Making Hydraulic & Hydrostatic Dump Truck
In this video we will show you how to make an interesting vehicle that will be very helpful on the farm and around the house.
You might say it was easier to use a lawn tractor and convert it, maybe it was, but we didn't have one and we had a lot of parts we wanted to use.
Parts we used:
- Hydrostatic transmission from a lawn tractor
- The main frame is made of a 70x50x3 mm channel
- The steering gear was found in a scrapyard, unfortunately I don't know what car it came from.
- Briggs & Stratton petrol engine 14 HP
- The seat is from some lawn tractor
- The footrests, sides and crate are made of 1.5 mm stainless steel
- Fuel tank from the gx200 engine
- The air conditioning compressor is probably from a Ford
- Hydraulic pump with a capacity of 10L / min
- Hydraulic cylinder with a height of 200 mm
Specifications are:
Weight approx. 250 kg
Load capacity on the trailer: approx. 400 kg
Power 14 km
Maximum speed 15 km/h
The dimensions of the box are 90 x 96 x 40 cm
Check out our other videos:
• Making revers trike to... - Making reverse trike to Have Fun :D
• Making Hybrid Stump Gr... - Making Hybrid Stump Grinder
• Making 14 Hp Brush Mow... - Making 14 Hp Brush Mower - using Lawn Mower parts
You're a great fabricator...always a pleasure to watch!
Thanks! 👍
You should start production… AMAZING INGENUITY…!!!!!!!😮❤😮
A nice build and a useful machine.
It's always a pleasure watching a master fabricator build stuff.
10/10 on the reparability though. There's not a SINGLE inaccessible void, other than the obvious hydraulic oil tank.
EXCELLENT idea with the AC compressor clutch. Keep it on the same belt, flip a switch and you have PTO. Love it.
True Professional and I couldn't stop watching this magician from start to finish and I hope he is self employed because he is too good to waste on someone else
These hydrostatic transmission need larger oil capacity a external filter. For heavy work. Many failed here in mountain lawn mowers. Axels can't carry much weight also. Excellent channel 👍 My grandparents from Poland Lithuania.
I agree even on relatively flat land any transaxle smaller than a Tuff torque k66 just won't last on slopes... Also most transaxles under 1inch axle shaft cannot hold much weight... Best bet is to use transaxle as a transmission with a separate load bearing axle with hubs chain driven from transaxle shafts with a 1.5:1 or 2:1 chain ratio driving the rear wheels
It doesn't help that the box stores spec 30w motor oil in the TTs (my homedepot cub's manual states 30w). TT specs 50w in their service manuals. Built in failures. Only buy the mowers from the dealers. They are made in the same factory but built to different specs for the different distributors. You want a JD, go to JD for it, not the box stores.
Another mechanical masterpiece .
The thing I like the most about your channel is the advanced thinking you constantly put forward. While the rest of the planet is busy destroying itself, you are busy engineering and making positive contributions. I hope you last forever!
Dude you are amazing
Great build... you could go bigger in size and make an industrial version of this... SO cool !
Protect this man at all costs, we need him in the coming apocalypse.
Wouldn't it be wiser to seek/know how to avoid being here for what you've rightly said IS coming [tribulation/apocalypse]? Sadly, most reject the truth/answer when they hear it because it's inconvenient to their lifestyle. If people only knew how bad it's going to be [globally] for those who reject the answer: To be right with God; Jesus-by grace thru faith *apart from* human effort: good works, rites, ceremony [Eph 2v8-9; Gal 2v16/3v10/5v4; Rom 3v20]. *"Truth is a stubborn thing"* "For then *there will be a great tribulation,* such as has not occurred since the beginning of the world until now, nor ever will" [Matt 24 v21]
"for those who reject the answer" Didn't God say that this would be how it is in the end?😫
Молодец мужик рукастый !
Time well spent. There can't be much to go wrong with this either and anything that does can be fixed easily enough.
*GREAT JOB! GOOD LUCK TO ALL* 😎
Хорошая работа!
Yet another masterpiece of engineering. You always make something that is not clear from the beginning, but as the build grows, everything comes together as one perfect example of what can be done with a little forethought and some considerable skill. Thanks for teaching us what can be done, Much appreciated video, helps add to inspire ideas for the future. From UK.
Great work my master you are awesome engineer thanks for the sharing this video sir 👍 😊❤😊❤❤
Idealny sprzęcik w gospodarstwie, piękna maszyna. Pozdrowionka
Silnik z połowy Malucha ;)
Też tak umiesz, ty połowa mózgu ?
This might be my favorite build of yours yet! Such a practical and useful creation. Always a big treat when you post a new video!
Amazing talent he have and shareing his idea to everyone how we can make it such . Impossible thing to possible. 🥰🥰🥰
Love all your projects, especially your vehicles!! I learned a lot from watching your projects. This one is amazing, thanks for sharing with us!!! How about showing us how to make a 4WD vehicle 😎🙏
That's the coolest thing ever! Makes me sad though because I just threw away a Cub Cadet hydrostatic drive...but I did use the engine and controls in a wood splitter build. About that firewood- get yourself some IBC totes 🙂
Love the longer formats. If i want to skip a section... Tap tap + 10 seconds. Buuut. If I want to watch the whole thing now i can!
Patrz jaki pomysłowy Dobromir!
Impressive! Very impressive! Such skill in fabrication.
μπράβο σου φίλε πολύ ωραία κατασκευή χρειάζεται σε κάθε είδους δουλειά σου εύχομαι ότι καλύτερο ευχαριστώ για το βιντεάκι 😊😊😊😊
you mate are one talented guy, Top Class
O Stary, jesteś genialny! Z chęcią bym u Ciebie pobierał nauki i pracował. Bardzo zazdroszczę (w pozytywnym tego słowa znaczeniu) wiedzy, umiejętności i precyzji wykonywanych rzeczy. Mega szacun!
I enjoy watching and guessing what you may do makes it fun. Excellent work
Very nice build and video, thanks.
Taczka zmotoryzowana
I really enjoyed this. Excellent fab skills.
As always....well made clever design,👍
Sweet, great execusion. I've been thinking of building something similar for a while just not made it to the top of the list.
Howdie from Canada 🇨🇦 Sk thinking about how you built this awesome workmanship for what ya do and build thank you for sharing with us this is worth watching ya got this something that can be used and easy to make don't have to be a rocket scientist to be able to do this later mighty fine 😊
Retrofitting an old AC clutch to your hydraulic pump was really done!
Very nice job. Excellent fabrication skills.
Jak zwykle kawał dobrej roboty 💪
Podziękował 👍😁
Браво Маэстро !!!
Paul from Fabs Rat hasn't got anything on this fabricator. Nice Work 👍
Quel travail. Bravo c’est vraiment super. Merci pour cette vidéo.
Hello everyone have a nice day this is the amazing video
Love the build 👍, this looks like the projects on those small tractor forums where owners will add a backhoe or front end loader to their garden tractors.
Looks and runs great. I would add a few link of chain to the side panels of bed and a hook in the bottom corners of end gate so you can hook the chains to keep the dump gate from fully opening this would allow you to dump a consistent amout of gravel dirt or wood chips for spreading it as you dumped
Awesome job and a good job on the paint too I like the color cool dump truck so I take it you're a machinist by trade because you look like you know what you're doing awesome video hope to see more of your builds
Kind of cool but that's why you pull a dump wagon behind your riding lawn mower
I was trying to come up with a reason why this would be better than just making it a small dump trailer and all I could think of is "tell me you can't back up a trailer...without tell me " 😂 Impressive fab work regardless
@ 22:32 ... Who needs drawings & plans 2 work 2;... when they R stored in your Brilliant Mind...
That cutting to fit the bracket, So much for nice powder coat
jak zwykle, rozdupcony system. Brawo!
Thanks, just great! 👍💪✌
Very nice. I probably would have put a longer exhaust on it as well.
Już wiem jak zrobić wspomaganie w traktorku dzięki wielkie 🤠
Хорошо получилось! Ты настоящий мастер!
Well done great idea.
Another great build love your videos
Awesome build. You make some really kool stuff. Can't waite to see what you build next. Cheers from Canada.
Pracowite i zdolne to chłopczysko z Podkarpacia , a propos najbardziej podoba mi się ta piła do cięcia , chyba sobie taką kupię do krajania mojej swojskiej suszonej kiełbasy 👍👍👍👍👍👍👍👍
I love that work excellent excellent work thanks for sharing your video look forward to the next one and I love your welding
Bonjour belle réalisation avec de l’a récupérations de pièces automobiles et très bien équipé dans l’atelier 👍
Железный человек, у него наверно повышнный гемоглобин, так железо чувствовать, за что бы он не брался всё получается на высшем уровне. Всего хорошего хорошего вам.
You never fail to impress!
Nice smal dump truck . Great job . 👍👍👏
Super super, wygląda naprawdę ciekawie, dużo pracy
che bomba! bravissimo!
Годный трактор получился. Жалко, что ремень привода и подшипники снизу ни чем не защищены от грязи и веток. Надолго их не хватит.
Если хочешь чтобы при сварке было видно дугу на камеру. Сделай очень яркий свет. Чтобы камера не меняла яркость.
Натяжение ремня гидравлики правильно сделал а ходового ремня неправильно
good builder very talented keep going we love this stuff
I enjoy watching your videos. You all ways come up with new ideas 👍all the way from California 🇦🇲
Cool new addition to the work toys. Thankyou for sharing with us. 😀
hi forma cool hydroaulice truck two cool ass truck two🎉
Very impressive!
Барзо добже, пан!
Beautiful!! ⚙🔧🪛🔩🗜🔗👍😀
Za cały dzień oglądania twojej pracy na żywo, mógłbym na fajrant sprzątać warsztat 😂😅
i'm here since you only had an angle grinder and a stick welder, impressive how far you have come.
thanks for being our viewer for so many years!
i love your projects because all of them are heavy-duty and really strong
Thank you 👍
Excellent work again !! very usefull and cool project! salutation from Montreal,Québec !👍👍👍👍
Io posso solo dirti che ogni video che fai è un capolavoro di ingegneria. Quanto vorrei poterti stringere la mano e dirti che sei un ragazzo davvero geniale. Grande DARUZ
Really good you are talented.
Amazing work!
Master of Fabrication
Great job!
Nice work,👍🏻
Nice machine. I' want to build something like this but instead driving in opposite. So sitting on engine and have the load in front. This to reduce the space taken for having a seat.
Well built!
Love it! Nice burnout at the end too!
سلام خسته نباشید عالیی مرسی که هستین ❤❤❤❤❤❤❤❤❤❤❤❤
Great job, as always
Cool machine 👍
I always look forward to the adventures in your videos. Very nice work, and especially using stuff that is salveged.
Super! Jak zawsze ciekawy film!
klasse, hat richtig Spaß gemacht dir zuzuschauen, sehr kreativ, top Ergebnis
Fajny sprzęt, niechaj służy i cieszy 😎
nice bild ! cheers ben.
Great video/design as always. 👍
Awesome truck!
Coraz bardziej złożone te twoje projekty😊Z takim progresem to juz niedlugo łodzie podwodne i promy kosmiczne zaczniesz budowac😅Jak zawsze 3mam kciuki🤞i pozdrawiam z drugiego końca naszego kraju😉
Tak na marginesie czy w 12 minucie i 40 sekundzie tak mniej więcej czy proces spawania nie jest czasem puszczony odwrotnie? Czy tylko ja się zawiesiłem 😂 Zawsze staram się przyglądać wszystkiemu dokładnie alu tu wydaje mi się że film ,,leci do tyłu"🙃ale to pewnie ja jestem zakrecony 🚀
Z takich narzedzi co nie masz a można by pomyśleć to czas powoli zbudować giętarkę do rur💪to by było dopiero coś🤩rurowe konstrukcje, klatki, ramoklatki, lekkie i wytrzymałe a nie zawsze spawane z ciężkich profili ciętych pod kątem 🔥
@@marekroszkiewicz3524 A no trochę trzeba rozwijać kanał i iść i odmienne konstrukcje 😁😁 Mam taką giętarkę, hydrauliczną, ale jakoś rzadko jest w użyciu, jakoś ta bardziej wole profile niż rury 😅😅