TRUCK DRIVE SHAFT REPAIR | Drive shaft repair and welding strengthening | Broken Drive shaft rebuild
2024 ж. 28 Сәу.
460 989 Рет қаралды
TRUCK DRIVE SHAFT REPAIR | Drive shaft repair and welding strengthening | Broken Drive shaft rebuild
#truck #drive #broken #pakistanitruck #reaper #welding #rebuild #shaft
Another episode of "let's see how far we can overload our truck"
A true artist. Babe Adams Golden Colorado USA
В каждом видео присутствует грустный мужчина, который просто стоит опершись о колонну...😀
это инженер по технике безопасности - он проверяет чтобы все были одеты в ночнушку и туфли с острым носом ахахахахаха
That’s the supervisor, ensuring they only wear open toes, no eye protection and no mask. 😂😂
I hope that arc welder ground lead is grounded to the piece he's welding and NOT clamped to the lathe. If the ground is clamped to the frame of the lathe all of the current is flowing through and arcing across the headstock bearings, that will damage the bearings.
So do you think this is the first time this guy did this type of work?
@@thepubliceye Why would you ask that? It's obvious that what he's doing is his job and he's doing the best with what he's got to work with. What I'm saying is a cautionary tale of why you should not ground the work through the body of an expensive lathe because the current flow will damage the bearings eventually via arc pitting between the balls/rollers and the race.
I understand that's one of those things that "Can Happen" but in reality seldom ever do. With roller bearings as tight as the lathe head it just doesn't happen. In addition to the rollers, there are a lot of steel gears and even a sleeve bushing.
@@thepubliceye I don't want to come across as argumentative or mean any disrespect to you but what I described is a real thing that happens and I was there when it was happening. Mechanics back in the 1980s working on Chrysler vehicles has a streak of bearing failures namely their front wheel bearings, we would just replace the bad bearings and the vehicle would return months later with the same problem. This happened frequently enough to where Chrysler engineers issued a TSB - Technical Service Bullitin when the figured out the cause of the premature bearing failure. There was no internet back then and mechanics got their 'critical' repair info via the TSB and that one directed us to look for loose or missing body ground cables/wires and to fix that issue while replacing the bad bearing. Over a period of time that problem once corrected went away. Peace
@@slomotrainwreck I am aware of that
у меня каждый раз сердце замирает - когда они стружку руками снимают. я один раз видел, как паренек потрогал стружку, просто потрогал, реки кровищи на всю жизнь отучили.
их бережет Аллах! Allah hafis!
Very interesting video on how to repair drive shafts - the one thing - you never see the drive shaft working - when they fix something I would like to see it working
I repair drive shafts and I can say this shaft is not balanced or zeroed out. It will fail in the same way it failed from the previous repair.
No sir, earlier someone had installed a piece of indigenous pipe, so that pipe broke, now we have installed a imported pipe, now it will not break. Thanks
That shaft will have so much vibration due to imbalance, guaranteed breakage.
@restorationtoolshop They did not use a dial indicator or a press to straighten after welding. You can't eyeball that stuff. It will fail.
EVEN IT WAS BALANCED DUE TO THE OVERLOADING OF THE TRUCKS IN THAT COUNTRY IT WILL FAIL.
@@kostasgrapatsas2074 okay thanks
Whats with the entire population wearing pajamas and sandles?
There is no way that that shaft will run true to the centrelineof the gearbox. They probably dont drive fast so the vibration wont be noticed. And itll get torn up with overloading anyway. Love to watch the work skills with what they have. Well done . Greetings from Australia
Уже ремонтировали сыромятиной - в этом месте и свернуло. Как всегда - из грвна и палок...
Молодцы ребята , очень уважаю!
This is the cleanest shop I've seen in a long time.
Thank you sir, you like our shop
Como serán las otras, si esta parece un basurero, taller horrible
All things relative this is a clean shop and some of the cleanest lathes also. That said I see shafts going into the lathe and not once have I seen anything wiped of floor sand. However if the a market accepts the results I guess it’s good enough, who am I to say.
Lol looks like a previous repair with sub par materials got twisted up like a pretzel and snapped off again in the same spot. That's one way to provide yourself job security, I suppose lol. Or, it could be a torque limiting safety feature, making it break in a predictable, easy to repair spot, in stead of screwing up the much more expensive gearbox or something. Either way, it's brilliant.
Порвало в месте предыдущей сварки миньонами)
Respect. I trust these guys.
Very nice work very well done you know what you doing very good job
Mashallah zabardast good work
Muy buena relación a esa cardan, saludos desde oaxaca México gracias por compartir.
Made in Индия или Пакистан, ой ой, с токарки можно в космос😮
Индийцы до луны благополучно долетели а вот УМНЫЕ ПРАВИЛЬНЫЕ СКРЕРОНОСНЫЕ расеянцы об луну распиздячились ОЙ ОЙ А ПАЧИМУ А ЧТО СЛУЧИЛАСЬ ВСЁ ПРОСТО ПОМЕШАЛА ЛИШНЯЯ ХРОМОСОМА ИЛИ ЖЕ ЯЙЦА ТАНЦОРУ ПОМЕШАЛИ
It looks like someone added an extension to the shaft that was too thin.
New full length tube would have been way better.
The weld is fine. But, I thought he would turn down the high spots in the weld while it was chucked up in the lathe.
You are right sir Thanks
Very nice work 👌👌👌👌👌
Отличный микрометр. И в целом операция - огонь.
Спасибо
Восторг! Несомненно, восторг!
6:19 спасибо за подсказку. А я думал, как же он его в станок вставит?
Good way to loose a finger - removing the shavings by hand when the lathe is still turning.
The way these trucks are so often overloaded and abused makes me realize why they just continue to replace with crummy stuff. It isn't really worth the cost and shipping for new replacement. My hat is off to these guys who create some pretty amazing stuff with old equipment. They make it work with what they have to work with. No waiting around for someone in a government agency to "save them". I'm wishing I was well off enough to send a c-111 full of safety gear and boots to these guys though 🙂.
Ремонт такой же уже был на этом кардане, и его свернуло, свернëт так же и этот ремонт 😀😀😀
А ТЕБЕ НЕ ПОХЕР СВЕРНЕТ НЕ СВЕРНЕТ КОГДА И ГДЕ СВЕРНЕТ ПРИНЕСЛИ ПРОСЯТ СДЕЛАЙ ЧЕЛОВЕК СДЕЛАЛ ты если руку сломаеш к врачу пойдеш и будеш лечиться хотя шанс перелома в дальнейшем все равно останется
Where is this filmed? Pakistan? What city?
Simply amazing.
Why not cut the ends off and replace the whole tube?
That's what we do in the USA
@@TOONMAN200because we do it right the first time. I guess its cheaper to use just a small section of pipe than an entire length.
The guy needed the extra money to buy more doo dads!
First of all in the USA I never seen a drive shaft twisted that bad.@@John_Redcorn_
You bill the customer for a complete length, you cut off only what you need and repair the gap. Extra profit, plus more shaft for the next job…
Hooray for the pajamas and sandals guys.
Just a thought… What would happen if they made it mandatory for their trucks to go over a weigh bridge to ensure they’re not exceeding the GVM of that vehicle. Can’t see that happening though, but it might prevent some of the catastrophic mechanical failures such as the one shown. Just saying 🤔👍
What about the most important bit, the balance. Unless you balance the shaft again it will just break again.
я подумал что на превью две рыбы.
Ты правильно подумал Спасибо
I hate to think what condition the lathe bearings are now in after being used as a conductor for the welding!!
عمود الدوران او مايسمى بالكردان مصنوع من الحديد الصلب. وهنا يتم تلحيمه وتوصيله بقطع حديد عادي غير معالج مما يتسبب في كسره مرة اخرى
انت على حق شكرًا لك
Ain't no way that's road worthy😂
As always great video. It's interesting to watch you guys repair stuff instead of sending it to the junk pile like most places these days. I'm sure the customer was happy to be back on the road asap. 👍
Thank you very much sir for liking our ka
Уже меняли в этом месте, по шву видно. Они понимают, что не на долго, но у них нет денег на новый.
Parabéns pelo seu trabalho 👏 👍 top 💖👏👏👏🤝🇧🇷🇧🇷🇧🇷🇧🇷🇮🇹🇧🇷🇮🇹
Выглядит надёжно
I built Rockwell drive shaft and Spicer drive shafts at Mack Trucks manufacture plant and at freightliner dealer ship and thats not how we repaired or built them Biggest error is splicing the tube If you noticed where it was twisted it had already been spliced next there is a indexing arrow on the stub that aligns with the slip tube that aligns with the yoke at the other end before welding ( the yokes will never align properly) true hacks that dont know what they are doing
No. First we have leveled the line of both the crosses and then we have done welding thank you
True hacks? That’s a little harsh. These guys are doing the best they can with limited resources. Give them a break.
我相信在巴基斯坦,人的技術比機器校準更為可靠
Why wouldn't you measure the shaft size and cut both ends off weld the ends back on and balance it ? This is not repaired .. this is job security
Após soldadura, é preciso calmar as tensões.
OMG - oiling the guideways, lathes that weren't built in Halifax in 1922, tidy workshop, am overwhelmed.
Okay Thanks
Seems like it would be easier to replace the whole entire pipe instead of piecing it all together 🤔
A longer piece of that tube is probably worth more than the truck itself!
Do these not need heat treated after welding?
ButI didn't see him align the U joints so that they're in phase...
Thanks 🙏
С карданом выдавать и инструкцию .,, Только по асфальту и без груза,,.
OSHA approved footwear?
Driver will get shaken, not stirred 😮
Почему не используете 3-кулачковый патрон на токарный станке ?
Потому что они точат кривые вещи. В 3-х кулачковом их замахаешься выставлять.
Not much people can't do this..the best skill..❤
very nice work
Thanks 🙏
Микрометр зачётный!
I have seen other channels do similar repairs with lots of high tech equipment, and the result is no better than this. Very enjoyable to watch your skill and ingenuity
Thank you very much
Shops with High Tech equipment wont repair drive shafts like that cause its just cheaper to replace.
@@The_Black_Sheep95 In Pakistan replacing is almost always not an option
@@The_Black_Sheep95 Thanks
@@The_Black_Sheep95 True but it's hard to grasp just how cheap labor is in Pakistan. It's so much less expensive to repair there. It used to be that way in the US also.
Mechanics fix the similar truck problem always, because drivers abuse their truck, overloading.
You are right Thanks
No they don’t there is no mechanic that will fix a drive shaft like this! It wont hold! Semi mechanics just replace the drive shaft with a new one! These need too be precisely balance or they break again or tear up the transmission
normal que ça casse avec un tube, à la base c'est du tube plein..... vu la force de traction ça pete
I like the third world country dial indicator they use for setting up job
Thanks
How about some oil on the center brace
Awesome job guys my grandfather was a machinist and I was amazed watching him you guys all have amazing skills and talent wow 👍 🇺🇸
Don't you just LOVE the sound of chatter coming from a dull tool?
The smoke is also a nice touch.
Trop fort 👍🏼👍🏼👍🏼👍🏼
We use a dial he uses a steel rod !
You are Right Thanks
That repaired drive shaft is probably more true than any new drive shaft built in the states !
Yeah, I think that’s a bit of a stretch of the imagination.😂
@@DimSimSam I don’t think that’s the first time they repaired that driveshaft in the same place . LoL 😂
not even watch the whole yet and can see the this “repair” has been done before and broke in the same spot the previous weld look strong.however the base metal of the repaired tube used is to soft that why it twisted.
You are correct, but it is not the welding that is broken, the pipe is broken thank you
Будет жуткая вибрация на определенной скорости,без балансировки .
Спасибо
Without doubt some of the best uploads on youtube , always a pleasure to watch , these "back yard " engineers have serious skills .
You are right they work for big vehicles thank you
Serios problemas con la seguridad personal
Super Coole Typen ...Respekt
а после сварки микрометром замерить биение десятки же будут.сварка ..сварка ведет металл
Вы правы, спасибо, сэр
Doesn't that driveshaft need to be balanced.........
You are right sir Thanks
Could have reached inside the six inch piece of pipe to weld like you did with the inside sleeve...?
No. One piece is welded from both sides inside and out and one is welded from outside only Thanks
... exzellentes Handwerk... 👍
Silly "fix" designed to get views. Other than that, an entertaining time.
That will definitely last until "next time"
You are correct thank you
No 3 jaw chuck was hurt during the making of this video….
No hurt, thank you sir
В данном случае зачем от трубы так ровно отрезать на станке, что-бы потом разрезать сваркой и приварить а потом опять на станок)? Все равно бить он будет жестко!
Вы правы, спасибо, сэр
Neat welding
Thanks
that's the same shop who made that shaft before it was broken
Yes, no, earlier they hired work from another workshop, now we have made it, it will not break thank you
They actually produce high quality repairs. The only thing you make is smart ass comments.
@@kode4420 thank you
@@kode4420yea lots of Google graduates come here for Mike these guys.😊
@@kode4420 haha high quality? probably it will be back soon in the same shop
Все заебись, на глаз, соосность выставляли молотком)))). Следующее мести под обрыв, там где стоял люнет
Вы правы, спасибо, сэр
Так по этому вставышу и будет отрывать , этот кардан наверное уже десятый раз ремонтируют .
@@user-vj4th8ks1i Ты прав Спасибо
@@restorationtoolshop Спорим, ты не понимаешь русский язык и даже не переводишь его.
The materials and the parts all are locally made not imported and the manufacturers shops are smaller than any local grocery store in United States
God job! Hopefully this time it will run next 5 miles without breaking apart.
Thanks Sir
It won't even make it out of the driveway.
@@markniilo Luckily for the owners all "repairs" included backlight-warranty. So most trucks never left these shops again.
It will work , most twisted drive shafts happen when forcing the tractor under a trailer that is heavy and too low . Or overloaded truck in a ditch and trying to just drive out . With normal use it will hold . Worked at trucking company 10 years and saw a few .
@@txrick4879 Impossible, working 10 years in Pakistan's trucking company, because until a few years ago, trucks were completely unknown in Pakistan and for all transportings donkey-carts were used. Maybe you're confusing it with a broken leg on a overloaded donkey?
Балансировка вала это лишнее 👌время еще на такую ерунду тратить
Restore master 👌👌👌🇮🇳🇮🇳🇮🇳🇮🇳
Thanks 🙏
High skill amazing you profesional mr x
Thanks Sir
Fabulous work.....!!
Very much cycle of liking the work sir
very nice job, only one major mistake, not maintaining the parallelism of the universal joint that will be mounted on the splined shaft of this shaft ! 🙏😩
@@staszekboroski526 According to us, we have done very well thank you
@@restorationtoolshop and the universal joints came out parallel ?
@@staszekboroski526 okay Thanks 🙏
I need some of these work pajamas.
Now the truck has a vibrating seat for the driver😂
Need oil
Will work just fine
Thanks Sir
@restorationtoolshop no problem u guys get it done thats all that matters
@@guypatts494 👍 okay
Best channel! The work done by the shop is always very professional and interesting to watch.
Thanks Sir
кардан крутан
Спасибо
I feel sorry for the truck driver 😵💫
Thanks 🙏
Do you think they say “that ain’t going nowhere “
Everything works in Pakistan thank you
Nice work bro 💯
Thanks Sir
Один раз уже провернуло, они опять горбатого лепят.
Родного в том кардане только шлицевая часть и приблизительная длинна и то не факт как думаеш кто лепит горбатого БОЛЬШЕ тот кто приносит или тот кому приносят тот кардан
You didn't want to use soft jaws on that driveshaft spline?
Yes Sir Thanks
They require balancing but that guarantees returned business it will fail again
Have not failed till date thank you