The plates that are connected with the two nuts and bolts should be non-electrical conductive. It should be nylon so there is no electrical current short between the positive and the negative plates. If using a metal bolt it needs to be covered with a plastic pipe preventing the plates from touching the mounting bolt that holds all of the plates together.
@HHOGAS Жыл бұрын
Nylon absorbs water... Might need a more exotic plastic or ceramic
@purduephotog Жыл бұрын
@@purduephotog 😂
@gepettobellucci8418 Жыл бұрын
Or simply put a plastic tube through the hole big enough for the bolt to fit through, to insulate it from the plates. I was thinking this as well.
@petedavis7970 Жыл бұрын
@@petedavis7970 or a slice of heat shrink. However, You want contact every other plate.
@andybilakshow260 Жыл бұрын
That's what I am seeing too. The separators are useless.
@ohlipbench Жыл бұрын
Made one of these with stainless steel wire ...gets an additional 6 -8 MPG on my 2002 Jeep GJ WJ Additionally it cleans out all the carbon in the engine ...Jeep runs great ...90,000 mile since the last tunup
@mikeespo77287 ай бұрын
BS
@Random-dq8ew3 күн бұрын
HHO gas is quite explosive, however, it can be used to cut or weld. If you want pure hydrogen, you need two 4 inch plastic tees. These should be oriented so that the two tees are connected with a 4 inch piece of pipe, and that the bottom ends have fittings, with removable caps, ( for cleaning). The two tees should each have the third opening, oriented straight up, to create two “chimney”. Add about 12 inches of 4 inch pipe, to each tee, and Top each one with a female 4 inch cap, and male plug cap. Drill 2 holes in each plug. One for a wire, and one for a tube, ( one side will produce pure Hydogen, while the other side will produce pure oxygen). These gasses can be moved into a bag, or other suitable container, with the use of diaphragm pump, and stored. This tube is filled with water, and so the two anodes, which are put only a few inches below the water level, connect electrically, through the water, below, however the two gasses are separated because of the shape of the apparatus (called a Bowman’s apparatus), and the fact that all gasses rise, in a liquid. 😁
@richardmcdonald75658 ай бұрын
I was doing this 20 years ago, I stopped doing it with stainless steel after learning that the water becomes contaminated with chromium and becomes hazardous waste. Carbon or graphite is better to use.
@timyorba Жыл бұрын
So glad someone mentioned such :D
@martinwashington3152 Жыл бұрын
how dangerous water pollutant explain better sr Tim yorba
@darwingarces1400 Жыл бұрын
trivalent chromium (Cr(III)) ion is considered an essential nutrient in humans for insulin, sugar, and lipid metabolism.
@cereusareoles9123 Жыл бұрын
Nikkel is good?
@carolkinde2420 Жыл бұрын
@@cereusareoles9123 is trivalent chromium the same as the chromium used in stainless steel?
@timyorba Жыл бұрын
Nice Vid!😀 Takes me back to when I used to do this stuff. I began over 10 years ago. You can produce the HHO, but it's not safe, takes lots of energy to produce, and loses efficiency quickly -unless you can get your hands on some platinum plates. Platinum plates won't break down during electrolysis, so no more brown muck from degraded Stainless Steel plates! Also, what you have here is a wet cell. A dry cell would work out better, and allow you to control the voltage better. Basically, you need to find the sweet spot (can't recall if it's about 2.2V between plates) to balance productivity and heat. The whole thing goes REAL deep! Sigh; it takes a lot of work to get things going right. After which, you learn that your car will fight against you because of the excess Oxygen produced. Yes, the ECU will soon try to set your results back to stock. So, you will need to separate the HH from the O. That means special membranes, that cost.... I finally stopped after realizing that I could simply make pure hydrogen using water + aluminum + drain cleaner. Even then, it's hard to control, unless you powderize the aluminum. But doing that can be costly and dangerous -going into bomb-making territory. Not something I wanna tangle with. I finally gave up on HHO ad Hydrogen. It ate a LOT of my time, but I also learned a lot while doing it. Best I ever got was about 50mpg, I think.
@hhofox Жыл бұрын
Try building a charcoal gasifier. You can crack enough water to run an 100% on the gas. This is also how I got my start building HHO devices and then I shifted to wood gasification and then later charcoal systems with water injection that produce "water gas" If you want to make a ton of H2 efficiently this is how you do it and anyone can do this. Note to anyone thinking electrolysis works for boosting an ICE., It dont work and you are just wasting your time and will eventually come to that conclusion after you spent gobbs of money and spent tons of time on it.
@Thrive-Off-Grid Жыл бұрын
About separating the H2 from the O2: Cant it be done rather easily by having seperate seperate electrodes in a water container that is open at the bottom, but seperate farther up, so all the o2 bubbles go up one funnel/ hose and all the h2 bubbles up the other?
@c2h7 Жыл бұрын
@@c2h7 Yes but limits your design that will not be very eficient.
@Thrive-Off-Grid Жыл бұрын
@@Thrive-Off-Grid how does the charcoal gasifier work for you? Or is it worth the trouble OR is it the same as these hydrogen gas solutions... Just a fun project to do with the kids but definitely not worth trying to make an actual, functional system that can replace gas to run ur automobile.
@teeshark6584 Жыл бұрын
@@teeshark6584 Yeah teach your kids how to build a gasifier and thats an important skill that will last them the rest of their life. Don't waste your time and money on an HHO device. They can not sustain running an engine nor will they even boost an engine. In the event of a power outage, no operating gas pumps etc. You can generate power on fuel you make your self. Just make fuel prior to the event and store it in 55 Gallon drums with lids. The fuel dont go bad unless you let moisture get in it. If you have never seen an engine run on wood it will blow your mind while waking you up a bit. As we were not taught about this technology in history class. This is nothing new and it ran the world at one point in history. In WW2 this is Europe used to fuel cars, farm equipment, stationary power etc when petroleum supply was cut off. There were over a million gasifiers in operation over there at that time.
@Thrive-Off-Grid Жыл бұрын
Even though you separated the plates, don't the 2 connecting metal bolts contact all the plates creating a short circuit?
@ProlificInvention Жыл бұрын
holes in the plate are bigger than bolts..
@albertnario4877 Жыл бұрын
I thought the same
@fazendocoisasinsanas Жыл бұрын
The inside bolt is insulated
@dapakers Жыл бұрын
@@albertnario4877 terminal both short circuit by washer !!!!
@pabanmahata8014 Жыл бұрын
@@albertnario4877 No. U know that wont fly?
@derekstarkjr5128 Жыл бұрын
excellent job describing your procedure results and effects of alterations thank you Albert
@edge2science7 ай бұрын
thanks
@albertnario48777 ай бұрын
i put my setup in a clear undersink water filter assembly (thick clear plastic)and held everything together with neoprene washers and nuts/bolts as to not touch the 2. have 1/4" bolts coming out the top of the filter system so i can hook up everything and it already has 3/4" adapters for hoses on top of the undersink water filter unit.
@naturalstatepoolandspallc3389 ай бұрын
Use nylon bolts to hold cell together. Shorting plates to each other.
@timcarico8908 Жыл бұрын
"1:54 ...you can see he makes the holes bigger on one set of plates so they never touch the bolt. It's all cool. =)" -@Squelchy
@Mack_Dingo Жыл бұрын
I was working at a hydrogen start up company in Toronto, same concept, but what they do is use thicker steal plates that they CNC channels to allow for more surface area of metal to water to increase efficiency.
@sleepycat6120 Жыл бұрын
Amount of energy from hydrogen is still less than the actual amount of energy from battery
@vanmam Жыл бұрын
@@vanmam true, however it would be interesting to see hho replace lithium Especially the instance of solar farms as the problem isn’t generating power while the sun is up, it’s of course storing power for when the sun is down
@userhandler0tten351 Жыл бұрын
Did they go out of business?
@BB-yj2rb Жыл бұрын
How can I contact this startup?
@salimsantouh1406 Жыл бұрын
@@salimsantouh1406 contact them for what purpose? These don't work. They're all a scam.
@BB-yj2rb Жыл бұрын
Very interesting ! You've done almost everything correct so far... NO glass jars ,a bubbler and a battery.... however you need to remember that even though the HHO makes the engine run smoother you will not gain anything in gas mileage unless you reduce the gasoline going into the engine. (everyone forgets that!) if your putting 20 mpg through the carb and add HHO your gas mileage will still show 20MPG ! so you must reduce that amount of gasoline to see better gas mileage. I liked your 1st cell the best, adding the neutral plates in my opinion is a waste of time, your better off just having them all +_+_+_+_+_ through the stack and you did that fantastically !.... Now Plate AREA (surface area of the plates) does relate to how much HHO is produced but only a small amount what has the bigger influence is amperage ! and the closer spacing of the plates of the cell you have the ability to create a heck of alot of HHO there .... if you put 200AMPS of DC into that cell (with larger wires ) you may well be able to run that car without ANY Gasoline ! .... I made a cell, reduced the gasoline going into the engine and achieved 45~48 MPG on a R22 toyota pickup back in the 1980's I figured I needed 12 LPM to achieve running without gas..... so I started building cells and getting a 200amp alternator.. SHTF and I never completed the project..... but, It Can be done ! .... you must keep the cells clean though I cleaned mine about once a month and I used KOH as the electrolyte and adjusted the amperage to 40amps to the cell and I was putting out 4LPM....to achieve that gas mileage.
@bobkelly244710 ай бұрын
not 100% true on your 20mpg add hho and still 20mpg, i built one for my Mercedes turbodiesel with no electric voltage whatsoever it added so much power to the motor i have to back off on the accelerator by almost half to stay at normal highway speeds so if you accelerate less you are burning less fuel , I don't tell anyone how I did it and what i use for making the vapor
@tonycavez8 ай бұрын
@@tonycavezyou can share with us. I also drive merc cdi. It would be helpful to save the plenet from ev
@ariolkolici89538 ай бұрын
What's KOH
@nealapple91927 ай бұрын
@@nealapple9192 Potassium Hydroxide (KOH) available on line , I used flakes as it is easier to deal with and desolves in water easy. used as the ACID to make your electrolyte add slowly and watch your amps climb on the amp gauge the more amps you draw the more HHO you will make. it is a STRONG ACID so act accordingly. I used 4" ABS Sewer pipe, caps and removable plugs (pop off plugs)
@bobkelly24477 ай бұрын
@@nealapple9192 an electrolyzer, Potassium hydroxide
@Jax02387 ай бұрын
The two screws in the middle are creating a direct short between the plates because each screw is touching both positive and negative plates because they are not insulated from touching the plates at the threads pass through areas!
@Duane002 Жыл бұрын
6 plates with small holes, 5 plates with large holes, the short circuit is excluded!
@jozsefjuhasz70 Жыл бұрын
Pls sir reply me
@V.kGarage6 күн бұрын
The frequency used in a hydrogen generator can affect the yield of gas, but it is not the only factor that determines the efficiency of the electrolysis process. Other factors such as the voltage, current, electrode materials, and the quality of water used can also affect the yield. In general, higher frequencies can increase the rate of gas production, but there is an optimal frequency for each hydrogen generator design that maximizes the gas yield. The optimal frequency can vary depending on the size and configuration of the electrodes, the distance between the electrodes, and the properties of the electrolyte solution. Typically, the frequency range for electrolysis of water is between 50 Hz to 10 kHz, but some designs may operate at higher frequencies. It's important to note that the use of high frequencies can also increase the risk of electrical arcing between the electrodes, which can damage the electrodes and reduce the overall efficiency of the system. If you are designing your own hydrogen generator, it is recommended to experiment with different frequencies while monitoring the gas yield and the overall efficiency of the system. This will help you determine the optimal frequency for your specific setup.
@dpgedward5947 Жыл бұрын
Correcto amigo, utilizando la frecuencia adecuada optimiza la producción de hidrógeno, reduce el amperaje de consumo y calentamiento del agua, muy bién
@hernanm2880 Жыл бұрын
На постоянном токе , работать не будет? Где-то видел что подключали аккумулятор.
@user-ft1ps9gw2r Жыл бұрын
@@user-ft1ps9gw2r right. Dc(batteries) has no frequency.
@chananielwizman240111 ай бұрын
DC is what is normally used in electrolysis. What frequency are you talking about?
@techskills404610 ай бұрын
@@techskills4046 freq main poster is Talking about.
@chananielwizman240110 ай бұрын
I love the production of hydrogen and the use of a spark to cut the power at the beginning of the video.
@kevinmiller5467 Жыл бұрын
I’ve done this exact experiment. I used stainless steel wire 3/16 diameter and probably took I think 5 feet I had to been to the specific way, but I did put a neutral in between two different polls. There is one flaw in that design once the water temperature exceeds that a boiling a chemical reaction changes, and becomes extremely unstable.
@sleezye100 Жыл бұрын
دوتا پیچ میانی که نظم صفحات تشکیل میده..عایق نشدن..ومتوجهشون نیست...باید با یک عایق از اتصال پیچ مهرهای میانی با صفحات جلوگیری کند🌷
@user-fn9vx7gr2z Жыл бұрын
Well you did a lot of thing wrong. First of all you need a square wave signal that is between 5hz and 10hz. Second you need to circulate the water. Third is to separate the gases and only capture the H2 not O.
@someguytu11 ай бұрын
A lot of comments talk about the water getting so hot it boils. Just think how much energy it takes to boil water. If you’re getting that energy from the cars alternator then it’s getting it from the cars engine, which is getting it from the fuel. This heat is a net energy loss to the system. This means it takes more energy to produce HHO than you recover by burning it in an engine that’s already only 30% efficient. You’re making your cars mileage worse by using these devices. I’ve seen properly done experiments that verify this. Car makers are desperate to produce more fuel efficient cars to meet federal and state regulations. If they thought this technology was possible they would have thrown a billion dollars at it instead of going to complex and expensive hybrids and other technologies.
@bcreason3 ай бұрын
Good job on the diy! Curious, why not run two separate chambers, one + and one -, that way one chamber produces pure H and the other O2?
@johnarizona38209 ай бұрын
Wow, producing HHO in an open container and you're wire sparks on contact, good thing there wasn't a lot of gas at the time.
@gregorsmith8541 Жыл бұрын
Hahah you are funny and clue less
@Viraldanceworlds Жыл бұрын
@@Viraldanceworlds You're hilarious, at least I have my eyebrows.
@gregorsmith8541 Жыл бұрын
@@gregorsmith8541 just gose to show your iq
@Viraldanceworlds Жыл бұрын
@@Viraldanceworlds Funny how I point out a safety concern and all you can do is try to be mean. I say try because you're opinion means nothing to me. So go ahead and try again. 😃
@gregorsmith8541 Жыл бұрын
the hands on manufacturing process video was great but i would have liked more thorough commentary. and more info on power source you used to supply the 4kw
@qhew Жыл бұрын
Nice build! Look for a switch that can handle that power
@adamalex74027 ай бұрын
Ótimo projeto, acrescente um regulador de volume de som por exemplo, e vai conseguir controlar a quantidade de energia que entra nas células.
@clone3dflex7 ай бұрын
Percebi um erro. Os parafusos que seguram as placas junto com os separadores causa curto entre as placas. Deveria ser de um material isolante.
@asandrom5 ай бұрын
@@asandromasta am vrut sa zic si eu, si de aceea se incinge apa si consumă bateria imediat, trebuie niște șuruburi de plastic, se gasesc in comerț!
@sergyy15 ай бұрын
@@asandrompendek tidak akan terjadi kerana plat dipisahkan dengan saiz lubang yang berbeza
@isajakwa4059Ай бұрын
You most place metal bolts in plastic pipes, isolate heads and nuts and after place tham all in holes in plates.
@mixailsarmazov4848 Жыл бұрын
Your HHO setup looks good, as long as you have PRE-COMPUTER CONTROLLED engines, even if We can DE-COMPUTER some of the new-er Vehicles and go back to "Normally aspirated" engines, because I don't think EV's will last long, there is Not enough Electricity being Made to re-charge them, so it will get to a point where the Government will STOP YOU CHARGING your nice new EV, and say that it is for the Better. The Western Governments are "Pushing" us all toward EV's, but with Basically no new ideas to Actually Make more Electricity for recharging all these EV's, I think it is all a "ruse" to get us out of Petrol or Diesel vehicles, and into Electric vehicles that are Nearly Impossible to maintain yourself, because of all the Computer stuff, and when they have you all in, Make the Entire EV market Fail at the Same time with a Flick of a switch, and Make us all walk or not leave certain areas, where your movements can be CONTROLLED, the English "15 minute cities" is the Starting point, what is NEXT. The Arabs are talking of a New Project called "The Wall" which will be a fully integrated city 170 KM long and can hold 9 Million People, a "Megapolis", I had seen Talked about back in the 80's, how many other Countries are also thinking of this Idea. ??
@scottcarr3264 Жыл бұрын
good job man, you are very resourceful! i see your electricity is pretty well all provided by the battery pack
@buttondeity39339 ай бұрын
Thank You, for your video. Just a little tip on drilling stainless. If you will use water in-lieu of WD40, it won't get as hot & will help your drill bits out. Cutting stainless as well. Learned this years ago from a guy on utoob that worked with alot of stainless & its saved him time cutting and drilling & money for bits and jigsaw blades. Again, nice video!! 👍👍
@paulshull9247 Жыл бұрын
you are wright but for this project trying to keep containment down is paramount, even grease from handling he needed to re wash the plates. maybe it would help pre drilling to assist the large peck drilling.
@RichieWellock9 ай бұрын
now that is one technically detailed work of an hho generator 👏👏
@b1ts3m45 Жыл бұрын
You should rough up the exteriors of the plates with a wire brush to increase their surface areas of the plates to increase HHO production.
@sky-son4 ай бұрын
VERY GOOD 👍 THANKYOU KEEP UP THE GREAT WORK FROM AUSTRALIA 🇦🇺
@renripari551410 ай бұрын
Nice project bro, very interesting, Ang galeng 👍 +1 sub for you..
@softbytesunlimited7 ай бұрын
Cramming such high voltage you will undoubtedly create a lot of heat.. After between , ( 6 to 11 ) hours of run time you're going to produce FOAM ... You need to keep this in mind when designing the whole system layout... Good video, thanks... Thom in Scotland.
@fuelban Жыл бұрын
Agreed. You need to clear away the bubbles so they don't form huge air gaps. The air gaps lower efficiency, and cause heating on the place due to the air being an insulator Use a mag drive pump to push water through the fins should force the bubbles out quick enough.
@ShivaTD420 Жыл бұрын
@@ShivaTD420 Indeed in principle, then you are correct, yet ... 6 to. 11 hours you get foam, which does not go away, so.. thinking on, how can you escape this conundrum I as you...well I have an answer, but first I offer you a question, a system of HHo, constricted in size, then thinking again a pump as you suggest, with bubbles of foam running tho it will at 12% collapse the pump flow... But I have resolved all of this.. Thom in Scotland.
@fuelban Жыл бұрын
@@fuelban ahh yes, I've seen this foam with copper electrolysis.
@ShivaTD420 Жыл бұрын
@@ShivaTD420 hi, this foam is a state of highly charged waters, and will happen with all types of electrodes, stainless steel 316 being most often used, but FOAM is part of every reactor type... After (6 to 11 ) hours running it occurs. Thom in Scotland.
@fuelban Жыл бұрын
The screws must be insulated with an insulating plastic tube
@MAMHZH Жыл бұрын
That's what t hought as well.
@clearraines49 Жыл бұрын
I just put a couple of layers of electrical heat shrink wrapping on them, it's quick & easy. As I'm always modifying & changing units from wet to dry cell units.
@melmacind Жыл бұрын
I used nylon all thread, washers and nuts
@jimbo9124 Жыл бұрын
Yes the bolt threads may touch the plate at the hole and can short circuit between the +ve and -ve plates.
@sajit63 Жыл бұрын
He instead had bigger holes on half on the plates and glass fiber "washers" between all of them. So the plates are insulated, but if he drops it, or the plates shifts out of plates it will touch the screw and short out
@philswift8116 Жыл бұрын
I think there was a video somewhere that you could use pulsed dc at 400khz to split water more efficiently.
@travismoore78497 ай бұрын
In conventional direct current electrolysis, various experimenters achieved a doubling of the gas volume at the same input power when a strong magnetic field acted parallel to the direction of flow of the ions of the electrolyte, i.e. in the same direction. The Lorentz force created a vortex (torsion) on the ions. The magnetic field was generated by neodymium permanent magnets. It was crucial that the correct electrical polarity was applied to the plates. If this is wrong compared to the north and south poles of the magnets, the gas evolution is lower. All processes of gas evolution take place in the Helmholtz bilayer. The Debuye length is also decisive there; thus, among other things, also the plate spacing. The amount of gas emitted can be increased if the electrodes of the electrolyzer are provided with carbon felt. The carbon pores thus increase the total area of the electrodes. A significant increase with high coefficients of performance (COP values) in gas yield is said to occur when the electrolyzer is charged when switching from direct current to nanopulses. This is what two Indian researchers claim. Figure 6 of their paper shows that nanopulse electrolysis is 31.56 times (3156%) more effective than conventional DC electrolysis at the same input power. The extremely steep nanopulses literally exert karate blows on the electrolyte molecules. Of course, this is only possible if space energy makes a significant contribution; because there is no such thing as perpetual motion. gehtanders.de/Downloads/waw-nanopulsDC-HHO-IJEE_13_v3n1.pdf
@hanswurtz5560 Жыл бұрын
Definitely recommend you try insulating the bolt on v2 of this. Should give better results
@carnagefpv82568 ай бұрын
1,5 миллиона просмотров за две недели. Вот это интерес!
@Siergiej.Motorv Жыл бұрын
Very good work. I hope you're not storing those gasses!
@olddanb18 ай бұрын
Awesome experiment, Like physics but never experimented too much with chemical and gas yet Might want to try the hydrogen experiments, energy storage part of it. Regards, Jean-François
@ChrysalideEngineering8 ай бұрын
bro, that output is pretty insane
@thorgraum1462 Жыл бұрын
Don't worry about the trolls, people like you pushes boundaries of human knowledge. I hope you get good income from KZhead to continue with your experiments. 😉👌
@mchaves7663 Жыл бұрын
"pushes boundaries of human knowledge"? This is OLD sh!t dude! 😂
@taunteratwill1787 Жыл бұрын
he's not pushing anything.. this is old tech... we used it for electroplating for decades. probably a century now.... and brown's gas (hydrogen as a fuel) is a 1960's PATENT
@harleyme3163 Жыл бұрын
Nice job on creating a huge spark just as you produced a load of hydrogen
@MrRedeyedJedi Жыл бұрын
Add a kind of piezo shaker, to remove the bubbles from the surface more quickly.
@WolfgangS8 ай бұрын
Even though there's something wrong, i still think this is the best video on hho i've ever seen, i can see you're really intrested in it and you did some research. Love this type of video, and the comment section is just *chef kiss*
@dongasta5612 Жыл бұрын
mine puts out that constantly.. why can his only take a quick shot? poor design.. (ps the center bolt grounds all the plates together so it would work in the first place, he'as drawing 4000 watts because its a short LOL mines tas 7 amps at 12 volts to make 3x more with half the plate size .. 80 warrs..
@harleyme3163 Жыл бұрын
This is the worst design on youtube
@4kays160 Жыл бұрын
HiFi 1000W amplifier, with sounds as mantra (low frequencies). S.Meyer worked with 1.2V : have to cumulate frequencies in phasis.
@fred-san Жыл бұрын
Jeezus! That's crazy, well done dude
@TheZombieSaints Жыл бұрын
I Congratulated you for the successful result of your 2HHO experience for improving the combustible problem in the future.
@narcissebernard1201 Жыл бұрын
2HO
@narcissebernard1201 Жыл бұрын
@@narcissebernard1201 Nope 2H2 + O2 since both are diatomic
@milanswoboda5457 Жыл бұрын
Alguns probleminhas prata funcionamento em carros. 1. Recarga rápida de bateria. 2. Recarga suficiente da bateria para produzir gás suficiente de autonomia. 3. Controle do aquecimento 4. E o mais importante, explosão seca do hidrogênio, fazendo a elevação da temperatura do cabeçote para 600 graus centígrados, provocando deformações no material que não foi feito para essa temperatura.
@Lacostta2 Жыл бұрын
Ele mostrou que e possível
@celiovieira3792 Жыл бұрын
o gás HHO deve ser misturado com o gás de escape e, assim, reduz a temperatura na cabeça
@darwingarces1400 Жыл бұрын
@@celiovieira3792 Ligar o motor é possivel, mas fazer o carro andar somente com esse gerador que ele fez, NÃO. fora que é burrice gastar 10x mais energia do que o necessario pra remover o hidrogenio da agua
@mrshadow57965 ай бұрын
Great video! It's nice to see people interested in hho.
@Hydrogen4Health Жыл бұрын
No it is not. HHO is scam
@afre3398 Жыл бұрын
@@afre3398 I'm sorry your having a bad day. Maybe tomorrow will be better.
@Hydrogen4Health Жыл бұрын
A 1.6l car needs only 4Amps and 0.26lpm for optimum performance as its mixed fuel nice vid dude
@joemason91876 ай бұрын
Excellent. I am sure that serial production will start soon and it will be possible to buy such a generator cheaply enough. My sincere congratulations and much success in production. LP Somy
@mmarjan1 Жыл бұрын
To be honest, if you kept multiple positives, multiple negatives and enter change the neutrals in between each layer, he would’ve produced 10 times as much like I said the enemy is heat. It works with you and against you the best way I found to do this experiment is using copper housings you can’t see the reaction except in the bubbler. It’s the only way to keep the unit cool enough to continue the process and be efficient I drove from east coast to west coast. I filled up one time ran fully hydrogen boost. It was the one it’s called. I drove over 4000 miles on one tank of gas.
@sleezye100 Жыл бұрын
Did you make your own unit or buy one? If you did build one, would you be interested in sharing how you did it?
@dimitriguzman3396 Жыл бұрын
Hmmm... wet or dry cell? What was the electrolyte made of? What voltage between plates? How many miles per gal? Did the water get muddy? Is this setup still working?
@hhofox Жыл бұрын
i too am curious. I bought an old truck (1990) to experiment with HHO. It was fuel injected and with my set up it burned MORE auto gas then before. I believe it was because the fuel sensors recognized increase in oxygen and just kept dumping more gas to match the oxygen. How can we over come that?
@pilotegardner Жыл бұрын
@@pilotegardner filter out the o2
@markcollard9326 Жыл бұрын
@@pilotegardner you have to build a ecu tuner. There are some good platforms out there based on a raspi and Arduino and allow you to control the fuel at any point and then you run a wide band sensor instead of a normal O2 sensor but it doesn't matter. In the end the extra O2 is consumed burning the hydrogen and the extra power is negated by the fact that you then run less gas and that means leads calories and less combustion power cause hydrogen and oxygen while very very combustible just doesn't do it vs gasoline under high compression ratios. The hydrogen and oxygen will ping and all sorts of fun shit.
@twistedsocal Жыл бұрын
If you configure your anode and cathode you can separate the two gasses completely.
@rexdenemo523510 ай бұрын
Thank you for speaking English some of these DIY videos. There are different languages and I’m a dumb American. I didn’t learn any other language. I have a hard enough time learning English and I’m English speaking.
@davebosma48083 ай бұрын
Yes , the bolts should be sleeved or made of a non+metallic material ( plastic )
@rickphillips7257 Жыл бұрын
пластины центральными болтами замыкают между собой, смысл от боковых контактов, надо трубку изолятор одевать на болты
@user-xg1jg5zu6q Жыл бұрын
Тут уже индусские законы физики задействованы
@keshstreet Жыл бұрын
Отверстие больше болта. Но трубку надеть действительно нужно.
@user-fe5rp9qd6z Жыл бұрын
Млодец, ты, заметил
@user-tu3yq8iz1s Жыл бұрын
The two central clamping bolts should be plastic bolts or have a plastic tube over the threads to eliminate the direct short at this point making the device not operate where it is shorted between plates.
@robgad2271 Жыл бұрын
1:54 ...you can see he makes the holes bigger on one set of plates so they never touch the bolt. It's all cool. =)
@mickenoss Жыл бұрын
i agree the main bolts cant be conductive it ruines the ability to even somewhat control n the output you have to fully seperate each plate 1 wire per plate if you need to do that but the person making this obviously has a creative mindset so im sure youll make a much better design if you really put your mind to it also liek you said the more power it takes to make more hho when the water is warmer so there is a preportinal gain in container size to the size of the electrolysis plates system you use so make the water conatiner bigger to keep the water cooler but once you figure out the design of the plates for the electrolysis hho generator youll figure out the rest fairly easier if you pay attention to all the stuff to optomize it! still cool video was hoping to see you make a decently working design tho
@krackd-tv1364 Жыл бұрын
@@krackd-tv1364 he is producing steam lol
@deadlypngoldies431 Жыл бұрын
you noticed to huh, dunno why these idiots try to baffle us with our own technology, they think they look smart, but they truly dont understand they're making themselves look kinda silly
@harleyme3163 Жыл бұрын
@@mickenoss THAT IS NOT ENOUGH SAFE! Plates not fixed on all x-y-z axis, FIXED ONLY ON Z AXIS!
@marketing3720 Жыл бұрын
nice work man.. i wander if we can make it bigger generator and use direct current from alternator.. will be so power so less gasoline
@mazdadaus28798 ай бұрын
How you can separate s.s. plates since you are using metal nut and bolts to fix all plates together although you use some material washer to keep the plates desperate but Boles are connecting all together. Please correct me if I am wrong.
@jamalfuzail43698 ай бұрын
Please ignore the uneducated people and keep doing what you're doing you're on the right path, great work!
@jamesfrancis8765 Жыл бұрын
Know-it-alls think they know everything. They feel superior, are dismissive of others' opinions, are unwilling to listen to others, and love to tell others how to do their job. Know-it-alls like to hear themselves talk. This behavior may become so ingrained that it becomes part of the know-it-all's personality. : "I would say that by listening to that motor there that the amateor sprocket is causing interference which in turn causes the combustion line to interfere with the flow in the dynaflow."
@Mr.Robert1 Жыл бұрын
@Mr. Robert yeah ignore those fancy pants know it all scientists that think this just an inefficient way to waste a lot of electrical energy to make a little chemical energy. Big oil and big EV just want to hid the fact that with enough fiddling, you can power your car with some water and a few rc batteries.
@ryanphillips8492 Жыл бұрын
Were there any comments like that? It looks like all cheers to me.
@Cineenvenordquist Жыл бұрын
Generating hydrogen is a cool school science experiment designed to impress kids and is about as easy as learning how to fart. But being able to safely store and use hydrogen in practical everyday applications (without blowing yourself up) is definitely not as easy as farting.
@Zodliness Жыл бұрын
Actually this technology was suppressed "In 1968 over 40 years ago in the Philippines, Daniel Dingel invented the first known "Water Powered Car" The water powered automobile invented by Mr. Dingel impressed past Filipino leaders such as Ferdinand Marcos and Corazon Aquino, whom expressed optimism for such an innovation, yet according to Daniel Dingel the Filipino government warned that such an invention as the water powered car would not be welcomed due to the agreements in place between the Filipino government, and the IMF (International Monetary Fund) along with the World Bank which prohibits any type of competition for such monopolies that each governing body controls such as fossil (oil) fuel."
@pepito79959 ай бұрын
Good work and succes
@Serius_Santai_Cerdas7 ай бұрын
Grato. Otima demonstração. Va em frente, voce vai se dar bem.
@pierpalumbo4156 ай бұрын
I think that your active plates area is 13*10 cm in 4 stacks. Each one of 4 stacks has 5 series plates. As per the HHO low, the max ampere for your each stack is 10.88A . and more than that is boiling. So 10.88A * 4 stacks = 43.52A . Then 43.52A*12.85V= 559.23 W . Which will generate 1.817 LPM . My humble advice is: Where that you use 5 plates/stack you volte per each 2 plates= 12.85v /4space = 3.21v . the recommended volts = 2.5~2 V. So If you add 1 more plate in each stack you will get more products with same Ampere and same Watts . It will be 2.272 LPM.using 12.85v/5space = 2.57v. I know that you know how to increase to the ampere to rech the 560w . Good luck. I am a H2O producer . My product is "ZX spectrum 200W and 410W" 0.95LPM and 1.95LPM
@H2ON_MEA Жыл бұрын
I also notice you are using an older vehicle that does Not have a computer controlling the Engine, this will work well because a computer STOPS you making any effective output increase. HHO does not seem to work well in Computer cars, because I tried it and even with other electronic devices to trick some of the Sensors it keeps learning that you are Tricking it, and Negates your advantages. So pre 90's cars with No computer you can make big inroads to your economy, new vehicles the Manufacturers INTENTIONALLY make it Impossible.
@scottcarr3264 Жыл бұрын
@@scottcarr3264 No... you're still putting fuel into it, so all it does is back off the pwm cycle for the fuel injectors, therefore using less gasoline, but the idle speed stays the same.
@kleetus92 Жыл бұрын
where can i find the formulas tha you are using to create more efficient hho generators?
@xjoke6981 Жыл бұрын
Can i contact you?
@cocoxan482711 ай бұрын
Well you do know if you drill holes in those plates smaller-diameter than the thickness of the plates you're adding surface area and can get more hydrogen production you can actually reduce the weight of each plate by about 80% while increasing the surface area
@miketully959211 ай бұрын
И потом большой "ПАРА-БУМ" и нашли деда километров за шесть ))Особенно при размыкании контактов ,искра и ****
@rubenhayastan4854 Жыл бұрын
Ну барабум вряд ли. Что б взорвался водород нужно точное соотношение в процентах. Он очищает его от кислорода через водяной замок(бутылку). Но тут другое. Даже не нужно подобное собирать, что б понять что это не работает! Можно просчитать. Есть все данные в таблицах. Сколько получается водорода электролизом и сколько он может отдать энергии потом сгорая. Так вот. меньше в половину при идеальных условиях. Это видео для идиотов ради заработка на рекламе от ютюба. Все.
@xxxl495 Жыл бұрын
@@xxxl495 я в этих делах не спец. Ну так этот кулибин собирает свою приблуду, дома на коленке) в гараже. А ели на это, замахнутся а промышлено,- заводском изотовлении. На ещё привлечь научно и следовательно технический институт
@user-tu3yq8iz1s Жыл бұрын
@@user-tu3yq8iz1s Зачем привлекать институт? Электролиз изучен и описан век назад. Это самый дорогой способ получения водорода. Очень дорогой. В школе на уроках такой был наглядный эксперимент. Я сам собирал такой на кухне, побаловаться. Энергии полученной таким путем гораздо меньше затраченной. Что тут смотреть? Кстати ещё так ЗЭКи на зоне из лезвий делают и чай кипятят. ещё со времен гулагла.
@xxxl495 Жыл бұрын
If the electrolyzer cell is pushed beyond its capabilities and creates a fog gas that is the electrolyte will pass through the bubbler and into the engine and crate engine damage. In the bubbler, you should see no cloudiness fog at the top of the bubbler if the bubbler is properly designed to handle the flow of gas with the proper amount of water to extract any fog moisture leaving the electrolyzer. It should also go through a porous plastic secondary filter system to extract moisture to assure a dry gas. The bubbler by itself will not remove all moisture and electrolyte 100% unless it goes through a secondary porous plastic filter system to finalize the dry gas process.
@HHOGAS Жыл бұрын
I wish good luck for you always for your work..I'm Khalil from Baghdad. Good bye
@khalilsalihalsaidy3674 Жыл бұрын
Está bien lo que hizo, mis observaciones son, 1.- Demasiado voltaje de batería, debe trabajar en 12 volt, que es lo que usa el vehículo, ésa batería debe estar recargándose con el alternador del vehículo, el cual se dañará por el consumo de la celda. 2.- todo el consumo de la celda lo tendrá que reponer el alternador del vehículo por lo tanto no se recomienda mas de 15 amperes 3.- la separación de laminas está bien, sólo que debe asegurar que la placa no se desplace y toque el perno poniendo un separador mas 3.- se requiere de un controlador de pulsos para limitar el consumo de energía y precisamente de ( éso depende el éxito del sistema ) conseguir que el controlador regule el amperaje de consumo que uno le programe, ya sea 15 amp. o unos 20 amp. si se quiere usar mas amperaje lo cual no recomiendo, se deberá cambiar el alternador por uno de mas capacidad de carga, me refiero a amperaje. Y por último, con la cantidad de hidrógeno que se ve produciendo en el video, por lo menos está consumiendo mas de 30 ampéres, con lo cual al cabo de 10 minuto o menos el agua estará hirviendo y perderá toda su eficiencia ya que a medida que el agua se calienta la calidad del hidrógeno disminuye, la ciencia está en un buen controlador CCPWM y refrigerar el agua, que siempre esté a la menor temperatura posible, saludos desde Chile y se les puedo ayudar con sus dudas encantado.
@hernanm2880 Жыл бұрын
El acero inoxidable es el ultimo en la escala De conductividad. Y a medida que reacciona el agua en la electrolisis, se genera calor. Creando mayor resistencia al flujo de corriente aplicada. Incrementandose De manera exponencial el consumo De energía. Igualmente la temperatura del electrolito. Placas gruesas demandan mayor consumo. Ideal placas De cobre en El (-) y de plata en el (+). La plata el primer elemento en la tabla de conductividad, y el cobre De Segundo. De resto serian ,puros calentadores de agua y generadores de oxalato de Cromo, un desecho canserigeno, que es Ese barro marron que generan las placas, de acero. Cuando se realiza la electrolosis, u oxido reduccion. En periodo de prueba un inversor de polaridad constante para restringir la migracion De cationes. Para minorar el deterioro de las placas y formacion de oxidos. Incluso utilizando agua destilada, al agregar El catalisador., se produce la oxido reduccion aplicando la corriente.
@junioralbertocarrillo323910 ай бұрын
El CCPWM es solo un regulador de intensidad. Cualquier regulador de intensidad funciona bien o limitador De corriente. Mientras las celdas estén bien configuradas generan calor, pero en menor cantidad. Una Buena recirculacion de electroliro y gases disipan el calor en el tanque De reservorio. Recomendable, instalarlo fuera del compartimiento del motor, pues se genera demasiado calor impidiendo la refrigeración de la celda. Si se emplea demasiado catalizador, al pasar el tiempo en La electrolisis, el electrolito se polariza disminuyendo la cantidad de producción de gas. La tensión de carga del vehículo no puede caer por debajo de 13.5 voltios .,con la celda en funcionamiento. Por debajo de ese limite el alternador no es capas de cargar la batería. Tensión no es igual a intensidad. Encender la celda con el motor en marcha, prender las luces y equipamiento del Vehículo y medir el voltaje de La bacteria .si cae por debajo de 13.5 voltios, en ese momento ya se esta descargando la batería. Esa es la prueba definitiva de que el modelo De la celda de hho funcione correctamente. Yo estoy fabricándolas ,con elevadores de tensión , me elevan El voltaje solo para la celda. Y puedo manejar el voltaje y amperage sin darle tanta caída De tensión en el sistema de carga del Vehículo. .
@junioralbertocarrillo32399 ай бұрын
the efficency got reduced, at 13V it was 30percent and it got down to 17percent at 48V
@zazugee Жыл бұрын
You should connect a water chiller to it some alittle bit distance from the tank. So the water can flow through it. An old radiator would work or. A array of copper tubes from a old air conditioner that's in a ice chest of something else to chill it. Have the water run through the cold. Pipes. And use as a cooler heat sink to not heat up water
@masterblaster9123 Жыл бұрын
or simply make one thats not shorted by the center bolt LOL
@harleyme3163 Жыл бұрын
Your cell works great . Now try making an ozone generator and mixing the ozone with the hho .
@Squeezingjuice101Ай бұрын
You have a long way to go & a lot to learn...
@thedevilsadvocate3577 Жыл бұрын
: "I would say that by listening to that motor there that the amateor sprocket is causing interference which in turn causes the combustion line to interfere with the flow in the dynaflow."
@Mr.Robert1 Жыл бұрын
great idea with the spacer material. You are using too many neutral plates tho. i get more bubbles with 4 plates for this kind of electrolizer, positive neutral neutral negative. it makes it a theoretical 6.6v but i find 12 works with a little heating which can be offset by extra electrolyte.
@cereusareoles9123 Жыл бұрын
Dyslexia
@stephenrocks7004 Жыл бұрын
Geralmente para fazer a separação eu uso acrílico com etil polimerisante
@fernandolima8250 Жыл бұрын
Добрый день! Расскажите, пожалуйста, подробнее про ваш метод разделения с использованием акрила.
@SvetRodaMoego Жыл бұрын
the pos and neg plates should not be connected which they are by means of the two bolts used to hold plates together.
@waynechannon52536 ай бұрын
Very informative thanks for posting 😊
@johnnychristo4895 Жыл бұрын
Muy bien excelente
@gloriaotalora350811 ай бұрын
Кундустане закони физики не существует, уних всё работает 😊
@rasuldjaisanovich656 Жыл бұрын
I think you would be using way more power to produce the hydrogen than what the car "gains" with the generator
@Mindcrime13 Жыл бұрын
That is exactly what happens.
@BobFeiring Жыл бұрын
Для производства одного киловатта энергии, требуется затратить 2 кВт. Сергей Васильев.
@UserUser-uq5ux Жыл бұрын
Brilliant, just brilliant DIYer!
@ORION4442222 ай бұрын
This is an amazing video great job you are very talented
@sebastianharrison611811 ай бұрын
We need to respect Faraday’s laws As a mathematical simplification of, a 7 plate generator will produce 64 ml/minute of HHO per 1 amp of current. Therefore a 120 watts generator will have a maximum output of 64 ml x 120 amp = 768 ml HHO You need about 12 cm2 of surface area for each watt usage or else your stainless steel plates or titanium will stress and erode Thus for a 120 watt transformer you need a surface area of 12cm2 x 120 = 1440 cm2 1440 cm2 divided by 12 is 120 cm2 Therefore the size of the plates need to be 12 x 10 cm big 4000 watt system needs 120\4000 x 1440 cm2 surface area = 48,000 square cm surface area or 4.8 square meters of stainless steel b!!!!!!
@janbeute4902 Жыл бұрын
Source?
@oceanmastersa Жыл бұрын
Our hydrogen plant uses deionized water (non conductive). Tap water is extremely conductive, hence your power wastage and high voltage. 😊
@anishaimagesolutions6097 Жыл бұрын
Did you know some Guide or archives about the HHO generators? I made one when i as little and want to build a Bigger one now using the Power from the outlet (DC 220v/10A)
@anonimoqualquer55039 ай бұрын
use distilled water , i believe he knows that , tap water is dirty it will attract a lot of garbage to the plates , i tried sea water it's so powerful it made loads of hho but melted my electrodes
@tonycavez8 ай бұрын
Very nice job simple and easy 😊
@yparadkar9 ай бұрын
Xt60 - 60a max. 80v*60a=4800w max. With a plate area of less than 1 meter square, more than 800 watts will boil water and there will be air between the plates.
@user-tx3hy5ly7i7 ай бұрын
Great, you've made something that can burn 4000 watts to produce a gas that you'll only get around half the energy back from when burned. Also stainless electrodes means you'll be turning some of the chrome in the anode into carcinogenic hexavalent chrome in your solution. Perfect.
@ferrumignis Жыл бұрын
You are way to kind with "around half", calculated he has about 16% conversion efficiency assuming this is pure gas without water vapors in it and this is on the heating value of the gas created.
@milanswoboda5457 Жыл бұрын
Thank you for highlighting the energy this device waste to produce a small amount of hydrogen / oxygen mixture
@brettjasonhead3740 Жыл бұрын
Todavía hay gente que fabrica estos componentes yo arme uno y hasta hoy no pude terminar ni probarlo al máximo primero que mi auto justo dejo de funcionar y probar su efectividad con transfirmador también es trabajoso seguramente funciona pero yo todavía no pude
@albertoramonacosta1212 Жыл бұрын
You give more than you get. What's the benefit? The cooling problem is also a gift.
@t.c.nevzatozdogru7929 Жыл бұрын
Use fiberglass bolts to hold the plates together. You can get fiberglass closet bolts, used to hold a toilet to the flange.
@billymule9619 ай бұрын
The great thing about a 4000 Watt hydrogen generator is that after you pump that hydrogen up to 10,000 PSI, store it in a tank and then later send what hasn't leaked out to a fuel cell you get 1400 Watts of power back. What a great deal!
@NackDSP9 ай бұрын
good job . good effort . room for improvement . careful . oxyhydrogen is more volatile than petrol . my question is : in another video . 1 ) show us you close the petrol supply and run entirely on oxyhydrogen 2 ) also before & after physical appearance of stainless steel plates & water .
@pakbusu Жыл бұрын
The car will not run on Hydrogen, there is not enough of it, to run even a small car of a generator like this you would need one the size of a truck, this generator would not even run a lawn mower.
@marksmusicCC Жыл бұрын
an American fellow did this back in the 70s on a 125cc bike (don't think it was Meyer). it ran well for about 20 mins then started to fail. I believe because petrol despite being fuel lubricates the pistons to some extent. without this the pistons just get eaten up from the friction. also requires radical timing change as HHO is implosive, not explosive. hence why most use only as additive :)
@chronicsys Жыл бұрын
@@chronicsys Petrol in the 70s was also full lead, this increases full density and it is also an upper cylinder lubricant. That same motor would not like current unleaded fuel either. It is not hard to make a motor run on gas, I have had several cars that run on LPG but Hydrogen is 1000 times more difficult to use than LPG. As I stated before simply pumping some gas down the air intake of any motor does not help anything. Hydrogen or HHO is not implosive, where on earth did you get that rubbish from.
@marksmusicCC Жыл бұрын
Nice to see your video. God bless you
@SohanLal-yq1su5 ай бұрын
I look to be easy but very dangerous. 😮thanks your experience explain. ❤
@raghupathyvp710522 күн бұрын
Brak tulejek separujących płytki od śrub...
@kapsel2105 Жыл бұрын
Верно, я тоже это заметил, должно было коротнуть, болты не изолированы от пластин просто тупа в ставлены текстоливые шайбы и плюсовые с минусовыми пластинами находятся в К. З
@user-tt4mc6ir9j Жыл бұрын
Center bolts should be plastic! Or in a insulated tube
@bluhuptie Жыл бұрын
yeah, he had bigger holes in the Neutral plates but I know what you mean, if any of those plates move and you "shorten the Voltage line you could get extreme amps instantly.
@scottcarr3264 Жыл бұрын
Wow ur bolts are not short circuiting. I m interested in such bolts only. Forget hydrogen.
@Arun-wd6zx Жыл бұрын
The added oxygen, O2, that is produced along with the hydrogen causes the oxygen sensors on the car to increase the fuel injector duty cycle which causes an increase in fuel to the cylinders which increases the RPM and gasoline consumption.
@billcrane24448 ай бұрын
It's a carburetor car no O2 sensor
@davenorman82514 ай бұрын
@@davenorman8251 Thanks. I didn't see that.
@billcrane24444 ай бұрын
would love to hear how your project goes when you refine it ,i think really need to reduce that voltage though as 48 will be had to integrate into car in the long term
@katiekumcgil Жыл бұрын
You do not want to put crap like this into your car ...You will use around 300 watt hours of energy to produce around 2 watt hours worth of hydrogen. Your fuel consumption will actually increase. ... this example would not even produce enough Hydrogen to run a lawn mower.
@marksmusicCC Жыл бұрын
I actually agree with that. Its not really saving energy unless you're converting it with solar. Cuz it takes to much energy to make it. Unless you ues aluminum. Which is consumed as a chemical reaction. The best way to convert it is very slowly. Wich is fine if you can store it.
@CalebGibbsAvenue Жыл бұрын
I like that it runs clean. And is very clean for a combination motors to run on. I'd love to run a nitrogen set up with my car to run as part of the fuel mixture.
@CalebGibbsAvenue Жыл бұрын
@@CalebGibbsAvenue Why would you want nitrogen ? it is an inert gas and it will hamper combustion. How would you tell your ECU that you have nitrogen or Hydrogen going into your motor ? How would you calibrate your O2 sensors ? Yes Hydrogen is very clean, the biggest problem with it is that you need a lot of it and a motor specifically designed for it. That car would also need a maintenance schedule that would rival that of a fighter jet. Hydrogen is very hard to store and needs a special tank, spaceX or NASA might be able to help you out there but it might cost a bit... good luck
@marksmusicCC Жыл бұрын
I meant NOS. Obviously, it's not that one. So far as regulating it I'd just use a propane regulator. But onistly I'd have no idea if it work. Just a thought. I'm merely describing the set up I have in mind.
@CalebGibbsAvenue Жыл бұрын
Is this producing a mixture of hydrogen and oxygen gas? Also, do you think it would be difficult or effective to connect some sort of system to circulate the water to a bigger take that has ice in it to keep the temperature down? Would that help the first design work better without increasing demand on load?
@doofusrickj19zeta75 Жыл бұрын
That's a Wet Cell, electrolysis start at 1,5 Dcv,if you are putting 12Dcv you are getting, home water heater, after 1,5 volts the rest of the voltage is wasted and goes to heat up the water,
@AlbertoMartinez-pb3sp Жыл бұрын
E=MC2 is just a joke!! OMG: Let's get educated #1. The most powerful part of a magnet is the center!!!, #2.The entire universe is magnetic. If it weren't for the center of a magnet AC current could not travel nor radio waves. FACT!! #3. If you want to play with anti gravity it's right at the center of a magnet!!!!!!!!!!!! TRY THIS: TAKE THE CENTER OF A BAR MAGNET AND TAP IT ON ANY NONE METALIC MATERIAL>> YOU DONT WANT TO DISRUPT THE MAGNETIC FIELD WITH ANY IRON>>> You will see it will loose about two thirds it weight.. Most UFO'S are not detected by Radar because they are none magnetic . Not in the North South pole thinking!!! IT'S ALL ABOUT THE "CENTER" get your act together. You need get past the North and South pole thinking..they are the weakest part of any magnetic field!! We all got screwed in the early ages by Edison and D.J. Ludwig. They would not allow Tesla to expose the center of a magnetic force and all the benefits to man kind. INDUCTANCE IS THE OSILLATION OF THE NORTH AND SOUTH Fields VIBRATING IN THE CENTER Field.::: The height of ones intelligence is directly proportional to their own realization of their own ignorance111111111111111111
@vincecox8376 Жыл бұрын
@@vincecox8376 what are you talking about? If you’re questioning my intelligence, I’m no Einstein but I am also not an idiot. I work in the power generation/transmission industry and have for 15 years but my knowledge is limited on this kind of stuff which is why I’m asking questions to try and better educate myself. Are you a bot? Unhinged? Or just trying to swing your dick around at random people?
@doofusrickj19zeta75 Жыл бұрын
Этот не передаваемый запах хлора!🥰
@alexanderbelkin59788 ай бұрын
Aqueous potassium hydroxide is employed as the electrolyte in alkaline batteries based on nickel-cadmium, nickel-hydrogen, and manganese dioxide-zinc. Potassium hydroxide is preferred over sodium hydroxide because its solutions are more conductive.[18] The nickel-metal hydride batteries in the Toyota Prius use a mixture of potassium hydroxide and sodium hydroxide.[19] Nickel-iron batteries also use potassium hydroxide electrolyte
@user-ec7lw3cq7b7 ай бұрын
Thanks for Upload this Video ! You can increase hho production enormously if you sonicate the water to be split with ultrasound. There are now reports that this method increases the hydrogen yield by a factor of 14. Or you can reduce the energy required in this way.
@DJENERGY63 Жыл бұрын
Nonsense! This is just wrong info - also in the mentioned video!
@rilosvideos877 Жыл бұрын
Have you tried that? Australian researchers have tested this possibility with ultrasound and achieved an increase in yield gas. That was in several news channels, not only to read on KZhead.
@DJENERGY63 Жыл бұрын
@@DJENERGY63 ultrasound frequency range is 2 to 18 megahertz. I used 8Mhz and I only get 2% extra, with same watt. Do you suggest a spesial hertz number
@H2ON_MEA Жыл бұрын
@@H2ON_MEA The question is, how do you bring in the ultrasonic frequency? As far as I know, the Australians installed a piezo speaker at the bottom of the electrolysis test rig, driving the sound directly into the electrolyte. The frequencies are me currently not known, but I would try 20-60 kHz. Power anywhere up to 10 W.
@DJENERGY63 Жыл бұрын
@@DJENERGY63 I see . Thanks for that information. I was pulsing the DC in 8KHz . So it is derance than you ment . Can you please right the name of the video from the Australians piezo speaker to search for it 🌹
@H2ON_MEA Жыл бұрын
You are creating highly explosive mixture of hydrogen and oxygen
@ksharindam Жыл бұрын
I wonder, what is the energetic efficiency of the hydrolyser? I have read that simple hydrolysers are around 50% efficiency. It is quite a science to rise the efficiency to 80%. Right plate material (Platinum maybe), right water solution with some salt or base like NaOH, right voltage and current on the plates. Plus hydrolyser water filling system, as there will be some pressure inside the hydrolyser.
@callmeadmin Жыл бұрын
Where did the electricity to charge the battery come from?
The plates that are connected with the two nuts and bolts should be non-electrical conductive. It should be nylon so there is no electrical current short between the positive and the negative plates. If using a metal bolt it needs to be covered with a plastic pipe preventing the plates from touching the mounting bolt that holds all of the plates together.
Nylon absorbs water... Might need a more exotic plastic or ceramic
@@purduephotog 😂
Or simply put a plastic tube through the hole big enough for the bolt to fit through, to insulate it from the plates. I was thinking this as well.
@@petedavis7970 or a slice of heat shrink. However, You want contact every other plate.
That's what I am seeing too. The separators are useless.
Made one of these with stainless steel wire ...gets an additional 6 -8 MPG on my 2002 Jeep GJ WJ Additionally it cleans out all the carbon in the engine ...Jeep runs great ...90,000 mile since the last tunup
BS
HHO gas is quite explosive, however, it can be used to cut or weld. If you want pure hydrogen, you need two 4 inch plastic tees. These should be oriented so that the two tees are connected with a 4 inch piece of pipe, and that the bottom ends have fittings, with removable caps, ( for cleaning). The two tees should each have the third opening, oriented straight up, to create two “chimney”. Add about 12 inches of 4 inch pipe, to each tee, and Top each one with a female 4 inch cap, and male plug cap. Drill 2 holes in each plug. One for a wire, and one for a tube, ( one side will produce pure Hydogen, while the other side will produce pure oxygen). These gasses can be moved into a bag, or other suitable container, with the use of diaphragm pump, and stored. This tube is filled with water, and so the two anodes, which are put only a few inches below the water level, connect electrically, through the water, below, however the two gasses are separated because of the shape of the apparatus (called a Bowman’s apparatus), and the fact that all gasses rise, in a liquid. 😁
I was doing this 20 years ago, I stopped doing it with stainless steel after learning that the water becomes contaminated with chromium and becomes hazardous waste. Carbon or graphite is better to use.
So glad someone mentioned such :D
how dangerous water pollutant explain better sr Tim yorba
trivalent chromium (Cr(III)) ion is considered an essential nutrient in humans for insulin, sugar, and lipid metabolism.
Nikkel is good?
@@cereusareoles9123 is trivalent chromium the same as the chromium used in stainless steel?
Nice Vid!😀 Takes me back to when I used to do this stuff. I began over 10 years ago. You can produce the HHO, but it's not safe, takes lots of energy to produce, and loses efficiency quickly -unless you can get your hands on some platinum plates. Platinum plates won't break down during electrolysis, so no more brown muck from degraded Stainless Steel plates! Also, what you have here is a wet cell. A dry cell would work out better, and allow you to control the voltage better. Basically, you need to find the sweet spot (can't recall if it's about 2.2V between plates) to balance productivity and heat. The whole thing goes REAL deep! Sigh; it takes a lot of work to get things going right. After which, you learn that your car will fight against you because of the excess Oxygen produced. Yes, the ECU will soon try to set your results back to stock. So, you will need to separate the HH from the O. That means special membranes, that cost.... I finally stopped after realizing that I could simply make pure hydrogen using water + aluminum + drain cleaner. Even then, it's hard to control, unless you powderize the aluminum. But doing that can be costly and dangerous -going into bomb-making territory. Not something I wanna tangle with. I finally gave up on HHO ad Hydrogen. It ate a LOT of my time, but I also learned a lot while doing it. Best I ever got was about 50mpg, I think.
Try building a charcoal gasifier. You can crack enough water to run an 100% on the gas. This is also how I got my start building HHO devices and then I shifted to wood gasification and then later charcoal systems with water injection that produce "water gas" If you want to make a ton of H2 efficiently this is how you do it and anyone can do this. Note to anyone thinking electrolysis works for boosting an ICE., It dont work and you are just wasting your time and will eventually come to that conclusion after you spent gobbs of money and spent tons of time on it.
About separating the H2 from the O2: Cant it be done rather easily by having seperate seperate electrodes in a water container that is open at the bottom, but seperate farther up, so all the o2 bubbles go up one funnel/ hose and all the h2 bubbles up the other?
@@c2h7 Yes but limits your design that will not be very eficient.
@@Thrive-Off-Grid how does the charcoal gasifier work for you? Or is it worth the trouble OR is it the same as these hydrogen gas solutions... Just a fun project to do with the kids but definitely not worth trying to make an actual, functional system that can replace gas to run ur automobile.
@@teeshark6584 Yeah teach your kids how to build a gasifier and thats an important skill that will last them the rest of their life. Don't waste your time and money on an HHO device. They can not sustain running an engine nor will they even boost an engine. In the event of a power outage, no operating gas pumps etc. You can generate power on fuel you make your self. Just make fuel prior to the event and store it in 55 Gallon drums with lids. The fuel dont go bad unless you let moisture get in it. If you have never seen an engine run on wood it will blow your mind while waking you up a bit. As we were not taught about this technology in history class. This is nothing new and it ran the world at one point in history. In WW2 this is Europe used to fuel cars, farm equipment, stationary power etc when petroleum supply was cut off. There were over a million gasifiers in operation over there at that time.
Even though you separated the plates, don't the 2 connecting metal bolts contact all the plates creating a short circuit?
holes in the plate are bigger than bolts..
I thought the same
The inside bolt is insulated
@@albertnario4877 terminal both short circuit by washer !!!!
@@albertnario4877 No. U know that wont fly?
excellent job describing your procedure results and effects of alterations thank you Albert
thanks
i put my setup in a clear undersink water filter assembly (thick clear plastic)and held everything together with neoprene washers and nuts/bolts as to not touch the 2. have 1/4" bolts coming out the top of the filter system so i can hook up everything and it already has 3/4" adapters for hoses on top of the undersink water filter unit.
Use nylon bolts to hold cell together. Shorting plates to each other.
"1:54 ...you can see he makes the holes bigger on one set of plates so they never touch the bolt. It's all cool. =)" -@Squelchy
I was working at a hydrogen start up company in Toronto, same concept, but what they do is use thicker steal plates that they CNC channels to allow for more surface area of metal to water to increase efficiency.
Amount of energy from hydrogen is still less than the actual amount of energy from battery
@@vanmam true, however it would be interesting to see hho replace lithium Especially the instance of solar farms as the problem isn’t generating power while the sun is up, it’s of course storing power for when the sun is down
Did they go out of business?
How can I contact this startup?
@@salimsantouh1406 contact them for what purpose? These don't work. They're all a scam.
Very interesting ! You've done almost everything correct so far... NO glass jars ,a bubbler and a battery.... however you need to remember that even though the HHO makes the engine run smoother you will not gain anything in gas mileage unless you reduce the gasoline going into the engine. (everyone forgets that!) if your putting 20 mpg through the carb and add HHO your gas mileage will still show 20MPG ! so you must reduce that amount of gasoline to see better gas mileage. I liked your 1st cell the best, adding the neutral plates in my opinion is a waste of time, your better off just having them all +_+_+_+_+_ through the stack and you did that fantastically !.... Now Plate AREA (surface area of the plates) does relate to how much HHO is produced but only a small amount what has the bigger influence is amperage ! and the closer spacing of the plates of the cell you have the ability to create a heck of alot of HHO there .... if you put 200AMPS of DC into that cell (with larger wires ) you may well be able to run that car without ANY Gasoline ! .... I made a cell, reduced the gasoline going into the engine and achieved 45~48 MPG on a R22 toyota pickup back in the 1980's I figured I needed 12 LPM to achieve running without gas..... so I started building cells and getting a 200amp alternator.. SHTF and I never completed the project..... but, It Can be done ! .... you must keep the cells clean though I cleaned mine about once a month and I used KOH as the electrolyte and adjusted the amperage to 40amps to the cell and I was putting out 4LPM....to achieve that gas mileage.
not 100% true on your 20mpg add hho and still 20mpg, i built one for my Mercedes turbodiesel with no electric voltage whatsoever it added so much power to the motor i have to back off on the accelerator by almost half to stay at normal highway speeds so if you accelerate less you are burning less fuel , I don't tell anyone how I did it and what i use for making the vapor
@@tonycavezyou can share with us. I also drive merc cdi. It would be helpful to save the plenet from ev
What's KOH
@@nealapple9192 Potassium Hydroxide (KOH) available on line , I used flakes as it is easier to deal with and desolves in water easy. used as the ACID to make your electrolyte add slowly and watch your amps climb on the amp gauge the more amps you draw the more HHO you will make. it is a STRONG ACID so act accordingly. I used 4" ABS Sewer pipe, caps and removable plugs (pop off plugs)
@@nealapple9192 an electrolyzer, Potassium hydroxide
The two screws in the middle are creating a direct short between the plates because each screw is touching both positive and negative plates because they are not insulated from touching the plates at the threads pass through areas!
6 plates with small holes, 5 plates with large holes, the short circuit is excluded!
Pls sir reply me
The frequency used in a hydrogen generator can affect the yield of gas, but it is not the only factor that determines the efficiency of the electrolysis process. Other factors such as the voltage, current, electrode materials, and the quality of water used can also affect the yield. In general, higher frequencies can increase the rate of gas production, but there is an optimal frequency for each hydrogen generator design that maximizes the gas yield. The optimal frequency can vary depending on the size and configuration of the electrodes, the distance between the electrodes, and the properties of the electrolyte solution. Typically, the frequency range for electrolysis of water is between 50 Hz to 10 kHz, but some designs may operate at higher frequencies. It's important to note that the use of high frequencies can also increase the risk of electrical arcing between the electrodes, which can damage the electrodes and reduce the overall efficiency of the system. If you are designing your own hydrogen generator, it is recommended to experiment with different frequencies while monitoring the gas yield and the overall efficiency of the system. This will help you determine the optimal frequency for your specific setup.
Correcto amigo, utilizando la frecuencia adecuada optimiza la producción de hidrógeno, reduce el amperaje de consumo y calentamiento del agua, muy bién
На постоянном токе , работать не будет? Где-то видел что подключали аккумулятор.
@@user-ft1ps9gw2r right. Dc(batteries) has no frequency.
DC is what is normally used in electrolysis. What frequency are you talking about?
@@techskills4046 freq main poster is Talking about.
I love the production of hydrogen and the use of a spark to cut the power at the beginning of the video.
I’ve done this exact experiment. I used stainless steel wire 3/16 diameter and probably took I think 5 feet I had to been to the specific way, but I did put a neutral in between two different polls. There is one flaw in that design once the water temperature exceeds that a boiling a chemical reaction changes, and becomes extremely unstable.
دوتا پیچ میانی که نظم صفحات تشکیل میده..عایق نشدن..ومتوجهشون نیست...باید با یک عایق از اتصال پیچ مهرهای میانی با صفحات جلوگیری کند🌷
Well you did a lot of thing wrong. First of all you need a square wave signal that is between 5hz and 10hz. Second you need to circulate the water. Third is to separate the gases and only capture the H2 not O.
A lot of comments talk about the water getting so hot it boils. Just think how much energy it takes to boil water. If you’re getting that energy from the cars alternator then it’s getting it from the cars engine, which is getting it from the fuel. This heat is a net energy loss to the system. This means it takes more energy to produce HHO than you recover by burning it in an engine that’s already only 30% efficient. You’re making your cars mileage worse by using these devices. I’ve seen properly done experiments that verify this. Car makers are desperate to produce more fuel efficient cars to meet federal and state regulations. If they thought this technology was possible they would have thrown a billion dollars at it instead of going to complex and expensive hybrids and other technologies.
Good job on the diy! Curious, why not run two separate chambers, one + and one -, that way one chamber produces pure H and the other O2?
Wow, producing HHO in an open container and you're wire sparks on contact, good thing there wasn't a lot of gas at the time.
Hahah you are funny and clue less
@@Viraldanceworlds You're hilarious, at least I have my eyebrows.
@@gregorsmith8541 just gose to show your iq
@@Viraldanceworlds Funny how I point out a safety concern and all you can do is try to be mean. I say try because you're opinion means nothing to me. So go ahead and try again. 😃
the hands on manufacturing process video was great but i would have liked more thorough commentary. and more info on power source you used to supply the 4kw
Nice build! Look for a switch that can handle that power
Ótimo projeto, acrescente um regulador de volume de som por exemplo, e vai conseguir controlar a quantidade de energia que entra nas células.
Percebi um erro. Os parafusos que seguram as placas junto com os separadores causa curto entre as placas. Deveria ser de um material isolante.
@@asandromasta am vrut sa zic si eu, si de aceea se incinge apa si consumă bateria imediat, trebuie niște șuruburi de plastic, se gasesc in comerț!
@@asandrompendek tidak akan terjadi kerana plat dipisahkan dengan saiz lubang yang berbeza
You most place metal bolts in plastic pipes, isolate heads and nuts and after place tham all in holes in plates.
Your HHO setup looks good, as long as you have PRE-COMPUTER CONTROLLED engines, even if We can DE-COMPUTER some of the new-er Vehicles and go back to "Normally aspirated" engines, because I don't think EV's will last long, there is Not enough Electricity being Made to re-charge them, so it will get to a point where the Government will STOP YOU CHARGING your nice new EV, and say that it is for the Better. The Western Governments are "Pushing" us all toward EV's, but with Basically no new ideas to Actually Make more Electricity for recharging all these EV's, I think it is all a "ruse" to get us out of Petrol or Diesel vehicles, and into Electric vehicles that are Nearly Impossible to maintain yourself, because of all the Computer stuff, and when they have you all in, Make the Entire EV market Fail at the Same time with a Flick of a switch, and Make us all walk or not leave certain areas, where your movements can be CONTROLLED, the English "15 minute cities" is the Starting point, what is NEXT. The Arabs are talking of a New Project called "The Wall" which will be a fully integrated city 170 KM long and can hold 9 Million People, a "Megapolis", I had seen Talked about back in the 80's, how many other Countries are also thinking of this Idea. ??
good job man, you are very resourceful! i see your electricity is pretty well all provided by the battery pack
Thank You, for your video. Just a little tip on drilling stainless. If you will use water in-lieu of WD40, it won't get as hot & will help your drill bits out. Cutting stainless as well. Learned this years ago from a guy on utoob that worked with alot of stainless & its saved him time cutting and drilling & money for bits and jigsaw blades. Again, nice video!! 👍👍
you are wright but for this project trying to keep containment down is paramount, even grease from handling he needed to re wash the plates. maybe it would help pre drilling to assist the large peck drilling.
now that is one technically detailed work of an hho generator 👏👏
You should rough up the exteriors of the plates with a wire brush to increase their surface areas of the plates to increase HHO production.
VERY GOOD 👍 THANKYOU KEEP UP THE GREAT WORK FROM AUSTRALIA 🇦🇺
Nice project bro, very interesting, Ang galeng 👍 +1 sub for you..
Cramming such high voltage you will undoubtedly create a lot of heat.. After between , ( 6 to 11 ) hours of run time you're going to produce FOAM ... You need to keep this in mind when designing the whole system layout... Good video, thanks... Thom in Scotland.
Agreed. You need to clear away the bubbles so they don't form huge air gaps. The air gaps lower efficiency, and cause heating on the place due to the air being an insulator Use a mag drive pump to push water through the fins should force the bubbles out quick enough.
@@ShivaTD420 Indeed in principle, then you are correct, yet ... 6 to. 11 hours you get foam, which does not go away, so.. thinking on, how can you escape this conundrum I as you...well I have an answer, but first I offer you a question, a system of HHo, constricted in size, then thinking again a pump as you suggest, with bubbles of foam running tho it will at 12% collapse the pump flow... But I have resolved all of this.. Thom in Scotland.
@@fuelban ahh yes, I've seen this foam with copper electrolysis.
@@ShivaTD420 hi, this foam is a state of highly charged waters, and will happen with all types of electrodes, stainless steel 316 being most often used, but FOAM is part of every reactor type... After (6 to 11 ) hours running it occurs. Thom in Scotland.
The screws must be insulated with an insulating plastic tube
That's what t hought as well.
I just put a couple of layers of electrical heat shrink wrapping on them, it's quick & easy. As I'm always modifying & changing units from wet to dry cell units.
I used nylon all thread, washers and nuts
Yes the bolt threads may touch the plate at the hole and can short circuit between the +ve and -ve plates.
He instead had bigger holes on half on the plates and glass fiber "washers" between all of them. So the plates are insulated, but if he drops it, or the plates shifts out of plates it will touch the screw and short out
I think there was a video somewhere that you could use pulsed dc at 400khz to split water more efficiently.
In conventional direct current electrolysis, various experimenters achieved a doubling of the gas volume at the same input power when a strong magnetic field acted parallel to the direction of flow of the ions of the electrolyte, i.e. in the same direction. The Lorentz force created a vortex (torsion) on the ions. The magnetic field was generated by neodymium permanent magnets. It was crucial that the correct electrical polarity was applied to the plates. If this is wrong compared to the north and south poles of the magnets, the gas evolution is lower. All processes of gas evolution take place in the Helmholtz bilayer. The Debuye length is also decisive there; thus, among other things, also the plate spacing. The amount of gas emitted can be increased if the electrodes of the electrolyzer are provided with carbon felt. The carbon pores thus increase the total area of the electrodes. A significant increase with high coefficients of performance (COP values) in gas yield is said to occur when the electrolyzer is charged when switching from direct current to nanopulses. This is what two Indian researchers claim. Figure 6 of their paper shows that nanopulse electrolysis is 31.56 times (3156%) more effective than conventional DC electrolysis at the same input power. The extremely steep nanopulses literally exert karate blows on the electrolyte molecules. Of course, this is only possible if space energy makes a significant contribution; because there is no such thing as perpetual motion. gehtanders.de/Downloads/waw-nanopulsDC-HHO-IJEE_13_v3n1.pdf
Definitely recommend you try insulating the bolt on v2 of this. Should give better results
1,5 миллиона просмотров за две недели. Вот это интерес!
Very good work. I hope you're not storing those gasses!
Awesome experiment, Like physics but never experimented too much with chemical and gas yet Might want to try the hydrogen experiments, energy storage part of it. Regards, Jean-François
bro, that output is pretty insane
Don't worry about the trolls, people like you pushes boundaries of human knowledge. I hope you get good income from KZhead to continue with your experiments. 😉👌
"pushes boundaries of human knowledge"? This is OLD sh!t dude! 😂
he's not pushing anything.. this is old tech... we used it for electroplating for decades. probably a century now.... and brown's gas (hydrogen as a fuel) is a 1960's PATENT
Nice job on creating a huge spark just as you produced a load of hydrogen
Add a kind of piezo shaker, to remove the bubbles from the surface more quickly.
Even though there's something wrong, i still think this is the best video on hho i've ever seen, i can see you're really intrested in it and you did some research. Love this type of video, and the comment section is just *chef kiss*
mine puts out that constantly.. why can his only take a quick shot? poor design.. (ps the center bolt grounds all the plates together so it would work in the first place, he'as drawing 4000 watts because its a short LOL mines tas 7 amps at 12 volts to make 3x more with half the plate size .. 80 warrs..
This is the worst design on youtube
HiFi 1000W amplifier, with sounds as mantra (low frequencies). S.Meyer worked with 1.2V : have to cumulate frequencies in phasis.
Jeezus! That's crazy, well done dude
I Congratulated you for the successful result of your 2HHO experience for improving the combustible problem in the future.
2HO
@@narcissebernard1201 Nope 2H2 + O2 since both are diatomic
Alguns probleminhas prata funcionamento em carros. 1. Recarga rápida de bateria. 2. Recarga suficiente da bateria para produzir gás suficiente de autonomia. 3. Controle do aquecimento 4. E o mais importante, explosão seca do hidrogênio, fazendo a elevação da temperatura do cabeçote para 600 graus centígrados, provocando deformações no material que não foi feito para essa temperatura.
Ele mostrou que e possível
o gás HHO deve ser misturado com o gás de escape e, assim, reduz a temperatura na cabeça
@@celiovieira3792 Ligar o motor é possivel, mas fazer o carro andar somente com esse gerador que ele fez, NÃO. fora que é burrice gastar 10x mais energia do que o necessario pra remover o hidrogenio da agua
Great video! It's nice to see people interested in hho.
No it is not. HHO is scam
@@afre3398 I'm sorry your having a bad day. Maybe tomorrow will be better.
A 1.6l car needs only 4Amps and 0.26lpm for optimum performance as its mixed fuel nice vid dude
Excellent. I am sure that serial production will start soon and it will be possible to buy such a generator cheaply enough. My sincere congratulations and much success in production. LP Somy
To be honest, if you kept multiple positives, multiple negatives and enter change the neutrals in between each layer, he would’ve produced 10 times as much like I said the enemy is heat. It works with you and against you the best way I found to do this experiment is using copper housings you can’t see the reaction except in the bubbler. It’s the only way to keep the unit cool enough to continue the process and be efficient I drove from east coast to west coast. I filled up one time ran fully hydrogen boost. It was the one it’s called. I drove over 4000 miles on one tank of gas.
Did you make your own unit or buy one? If you did build one, would you be interested in sharing how you did it?
Hmmm... wet or dry cell? What was the electrolyte made of? What voltage between plates? How many miles per gal? Did the water get muddy? Is this setup still working?
i too am curious. I bought an old truck (1990) to experiment with HHO. It was fuel injected and with my set up it burned MORE auto gas then before. I believe it was because the fuel sensors recognized increase in oxygen and just kept dumping more gas to match the oxygen. How can we over come that?
@@pilotegardner filter out the o2
@@pilotegardner you have to build a ecu tuner. There are some good platforms out there based on a raspi and Arduino and allow you to control the fuel at any point and then you run a wide band sensor instead of a normal O2 sensor but it doesn't matter. In the end the extra O2 is consumed burning the hydrogen and the extra power is negated by the fact that you then run less gas and that means leads calories and less combustion power cause hydrogen and oxygen while very very combustible just doesn't do it vs gasoline under high compression ratios. The hydrogen and oxygen will ping and all sorts of fun shit.
If you configure your anode and cathode you can separate the two gasses completely.
Thank you for speaking English some of these DIY videos. There are different languages and I’m a dumb American. I didn’t learn any other language. I have a hard enough time learning English and I’m English speaking.
Yes , the bolts should be sleeved or made of a non+metallic material ( plastic )
пластины центральными болтами замыкают между собой, смысл от боковых контактов, надо трубку изолятор одевать на болты
Тут уже индусские законы физики задействованы
Отверстие больше болта. Но трубку надеть действительно нужно.
Млодец, ты, заметил
The two central clamping bolts should be plastic bolts or have a plastic tube over the threads to eliminate the direct short at this point making the device not operate where it is shorted between plates.
1:54 ...you can see he makes the holes bigger on one set of plates so they never touch the bolt. It's all cool. =)
i agree the main bolts cant be conductive it ruines the ability to even somewhat control n the output you have to fully seperate each plate 1 wire per plate if you need to do that but the person making this obviously has a creative mindset so im sure youll make a much better design if you really put your mind to it also liek you said the more power it takes to make more hho when the water is warmer so there is a preportinal gain in container size to the size of the electrolysis plates system you use so make the water conatiner bigger to keep the water cooler but once you figure out the design of the plates for the electrolysis hho generator youll figure out the rest fairly easier if you pay attention to all the stuff to optomize it! still cool video was hoping to see you make a decently working design tho
@@krackd-tv1364 he is producing steam lol
you noticed to huh, dunno why these idiots try to baffle us with our own technology, they think they look smart, but they truly dont understand they're making themselves look kinda silly
@@mickenoss THAT IS NOT ENOUGH SAFE! Plates not fixed on all x-y-z axis, FIXED ONLY ON Z AXIS!
nice work man.. i wander if we can make it bigger generator and use direct current from alternator.. will be so power so less gasoline
How you can separate s.s. plates since you are using metal nut and bolts to fix all plates together although you use some material washer to keep the plates desperate but Boles are connecting all together. Please correct me if I am wrong.
Please ignore the uneducated people and keep doing what you're doing you're on the right path, great work!
Know-it-alls think they know everything. They feel superior, are dismissive of others' opinions, are unwilling to listen to others, and love to tell others how to do their job. Know-it-alls like to hear themselves talk. This behavior may become so ingrained that it becomes part of the know-it-all's personality. : "I would say that by listening to that motor there that the amateor sprocket is causing interference which in turn causes the combustion line to interfere with the flow in the dynaflow."
@Mr. Robert yeah ignore those fancy pants know it all scientists that think this just an inefficient way to waste a lot of electrical energy to make a little chemical energy. Big oil and big EV just want to hid the fact that with enough fiddling, you can power your car with some water and a few rc batteries.
Were there any comments like that? It looks like all cheers to me.
Generating hydrogen is a cool school science experiment designed to impress kids and is about as easy as learning how to fart. But being able to safely store and use hydrogen in practical everyday applications (without blowing yourself up) is definitely not as easy as farting.
Actually this technology was suppressed "In 1968 over 40 years ago in the Philippines, Daniel Dingel invented the first known "Water Powered Car" The water powered automobile invented by Mr. Dingel impressed past Filipino leaders such as Ferdinand Marcos and Corazon Aquino, whom expressed optimism for such an innovation, yet according to Daniel Dingel the Filipino government warned that such an invention as the water powered car would not be welcomed due to the agreements in place between the Filipino government, and the IMF (International Monetary Fund) along with the World Bank which prohibits any type of competition for such monopolies that each governing body controls such as fossil (oil) fuel."
Good work and succes
Grato. Otima demonstração. Va em frente, voce vai se dar bem.
I think that your active plates area is 13*10 cm in 4 stacks. Each one of 4 stacks has 5 series plates. As per the HHO low, the max ampere for your each stack is 10.88A . and more than that is boiling. So 10.88A * 4 stacks = 43.52A . Then 43.52A*12.85V= 559.23 W . Which will generate 1.817 LPM . My humble advice is: Where that you use 5 plates/stack you volte per each 2 plates= 12.85v /4space = 3.21v . the recommended volts = 2.5~2 V. So If you add 1 more plate in each stack you will get more products with same Ampere and same Watts . It will be 2.272 LPM.using 12.85v/5space = 2.57v. I know that you know how to increase to the ampere to rech the 560w . Good luck. I am a H2O producer . My product is "ZX spectrum 200W and 410W" 0.95LPM and 1.95LPM
I also notice you are using an older vehicle that does Not have a computer controlling the Engine, this will work well because a computer STOPS you making any effective output increase. HHO does not seem to work well in Computer cars, because I tried it and even with other electronic devices to trick some of the Sensors it keeps learning that you are Tricking it, and Negates your advantages. So pre 90's cars with No computer you can make big inroads to your economy, new vehicles the Manufacturers INTENTIONALLY make it Impossible.
@@scottcarr3264 No... you're still putting fuel into it, so all it does is back off the pwm cycle for the fuel injectors, therefore using less gasoline, but the idle speed stays the same.
where can i find the formulas tha you are using to create more efficient hho generators?
Can i contact you?
Well you do know if you drill holes in those plates smaller-diameter than the thickness of the plates you're adding surface area and can get more hydrogen production you can actually reduce the weight of each plate by about 80% while increasing the surface area
И потом большой "ПАРА-БУМ" и нашли деда километров за шесть ))Особенно при размыкании контактов ,искра и ****
Ну барабум вряд ли. Что б взорвался водород нужно точное соотношение в процентах. Он очищает его от кислорода через водяной замок(бутылку). Но тут другое. Даже не нужно подобное собирать, что б понять что это не работает! Можно просчитать. Есть все данные в таблицах. Сколько получается водорода электролизом и сколько он может отдать энергии потом сгорая. Так вот. меньше в половину при идеальных условиях. Это видео для идиотов ради заработка на рекламе от ютюба. Все.
@@xxxl495 я в этих делах не спец. Ну так этот кулибин собирает свою приблуду, дома на коленке) в гараже. А ели на это, замахнутся а промышлено,- заводском изотовлении. На ещё привлечь научно и следовательно технический институт
@@user-tu3yq8iz1s Зачем привлекать институт? Электролиз изучен и описан век назад. Это самый дорогой способ получения водорода. Очень дорогой. В школе на уроках такой был наглядный эксперимент. Я сам собирал такой на кухне, побаловаться. Энергии полученной таким путем гораздо меньше затраченной. Что тут смотреть? Кстати ещё так ЗЭКи на зоне из лезвий делают и чай кипятят. ещё со времен гулагла.
If the electrolyzer cell is pushed beyond its capabilities and creates a fog gas that is the electrolyte will pass through the bubbler and into the engine and crate engine damage. In the bubbler, you should see no cloudiness fog at the top of the bubbler if the bubbler is properly designed to handle the flow of gas with the proper amount of water to extract any fog moisture leaving the electrolyzer. It should also go through a porous plastic secondary filter system to extract moisture to assure a dry gas. The bubbler by itself will not remove all moisture and electrolyte 100% unless it goes through a secondary porous plastic filter system to finalize the dry gas process.
I wish good luck for you always for your work..I'm Khalil from Baghdad. Good bye
Está bien lo que hizo, mis observaciones son, 1.- Demasiado voltaje de batería, debe trabajar en 12 volt, que es lo que usa el vehículo, ésa batería debe estar recargándose con el alternador del vehículo, el cual se dañará por el consumo de la celda. 2.- todo el consumo de la celda lo tendrá que reponer el alternador del vehículo por lo tanto no se recomienda mas de 15 amperes 3.- la separación de laminas está bien, sólo que debe asegurar que la placa no se desplace y toque el perno poniendo un separador mas 3.- se requiere de un controlador de pulsos para limitar el consumo de energía y precisamente de ( éso depende el éxito del sistema ) conseguir que el controlador regule el amperaje de consumo que uno le programe, ya sea 15 amp. o unos 20 amp. si se quiere usar mas amperaje lo cual no recomiendo, se deberá cambiar el alternador por uno de mas capacidad de carga, me refiero a amperaje. Y por último, con la cantidad de hidrógeno que se ve produciendo en el video, por lo menos está consumiendo mas de 30 ampéres, con lo cual al cabo de 10 minuto o menos el agua estará hirviendo y perderá toda su eficiencia ya que a medida que el agua se calienta la calidad del hidrógeno disminuye, la ciencia está en un buen controlador CCPWM y refrigerar el agua, que siempre esté a la menor temperatura posible, saludos desde Chile y se les puedo ayudar con sus dudas encantado.
El acero inoxidable es el ultimo en la escala De conductividad. Y a medida que reacciona el agua en la electrolisis, se genera calor. Creando mayor resistencia al flujo de corriente aplicada. Incrementandose De manera exponencial el consumo De energía. Igualmente la temperatura del electrolito. Placas gruesas demandan mayor consumo. Ideal placas De cobre en El (-) y de plata en el (+). La plata el primer elemento en la tabla de conductividad, y el cobre De Segundo. De resto serian ,puros calentadores de agua y generadores de oxalato de Cromo, un desecho canserigeno, que es Ese barro marron que generan las placas, de acero. Cuando se realiza la electrolosis, u oxido reduccion. En periodo de prueba un inversor de polaridad constante para restringir la migracion De cationes. Para minorar el deterioro de las placas y formacion de oxidos. Incluso utilizando agua destilada, al agregar El catalisador., se produce la oxido reduccion aplicando la corriente.
El CCPWM es solo un regulador de intensidad. Cualquier regulador de intensidad funciona bien o limitador De corriente. Mientras las celdas estén bien configuradas generan calor, pero en menor cantidad. Una Buena recirculacion de electroliro y gases disipan el calor en el tanque De reservorio. Recomendable, instalarlo fuera del compartimiento del motor, pues se genera demasiado calor impidiendo la refrigeración de la celda. Si se emplea demasiado catalizador, al pasar el tiempo en La electrolisis, el electrolito se polariza disminuyendo la cantidad de producción de gas. La tensión de carga del vehículo no puede caer por debajo de 13.5 voltios .,con la celda en funcionamiento. Por debajo de ese limite el alternador no es capas de cargar la batería. Tensión no es igual a intensidad. Encender la celda con el motor en marcha, prender las luces y equipamiento del Vehículo y medir el voltaje de La bacteria .si cae por debajo de 13.5 voltios, en ese momento ya se esta descargando la batería. Esa es la prueba definitiva de que el modelo De la celda de hho funcione correctamente. Yo estoy fabricándolas ,con elevadores de tensión , me elevan El voltaje solo para la celda. Y puedo manejar el voltaje y amperage sin darle tanta caída De tensión en el sistema de carga del Vehículo. .
the efficency got reduced, at 13V it was 30percent and it got down to 17percent at 48V
You should connect a water chiller to it some alittle bit distance from the tank. So the water can flow through it. An old radiator would work or. A array of copper tubes from a old air conditioner that's in a ice chest of something else to chill it. Have the water run through the cold. Pipes. And use as a cooler heat sink to not heat up water
or simply make one thats not shorted by the center bolt LOL
Your cell works great . Now try making an ozone generator and mixing the ozone with the hho .
You have a long way to go & a lot to learn...
: "I would say that by listening to that motor there that the amateor sprocket is causing interference which in turn causes the combustion line to interfere with the flow in the dynaflow."
great idea with the spacer material. You are using too many neutral plates tho. i get more bubbles with 4 plates for this kind of electrolizer, positive neutral neutral negative. it makes it a theoretical 6.6v but i find 12 works with a little heating which can be offset by extra electrolyte.
Dyslexia
Geralmente para fazer a separação eu uso acrílico com etil polimerisante
Добрый день! Расскажите, пожалуйста, подробнее про ваш метод разделения с использованием акрила.
the pos and neg plates should not be connected which they are by means of the two bolts used to hold plates together.
Very informative thanks for posting 😊
Muy bien excelente
Кундустане закони физики не существует, уних всё работает 😊
I think you would be using way more power to produce the hydrogen than what the car "gains" with the generator
That is exactly what happens.
Для производства одного киловатта энергии, требуется затратить 2 кВт. Сергей Васильев.
Brilliant, just brilliant DIYer!
This is an amazing video great job you are very talented
We need to respect Faraday’s laws As a mathematical simplification of, a 7 plate generator will produce 64 ml/minute of HHO per 1 amp of current. Therefore a 120 watts generator will have a maximum output of 64 ml x 120 amp = 768 ml HHO You need about 12 cm2 of surface area for each watt usage or else your stainless steel plates or titanium will stress and erode Thus for a 120 watt transformer you need a surface area of 12cm2 x 120 = 1440 cm2 1440 cm2 divided by 12 is 120 cm2 Therefore the size of the plates need to be 12 x 10 cm big 4000 watt system needs 120\4000 x 1440 cm2 surface area = 48,000 square cm surface area or 4.8 square meters of stainless steel b!!!!!!
Source?
Our hydrogen plant uses deionized water (non conductive). Tap water is extremely conductive, hence your power wastage and high voltage. 😊
Did you know some Guide or archives about the HHO generators? I made one when i as little and want to build a Bigger one now using the Power from the outlet (DC 220v/10A)
use distilled water , i believe he knows that , tap water is dirty it will attract a lot of garbage to the plates , i tried sea water it's so powerful it made loads of hho but melted my electrodes
Very nice job simple and easy 😊
Xt60 - 60a max. 80v*60a=4800w max. With a plate area of less than 1 meter square, more than 800 watts will boil water and there will be air between the plates.
Great, you've made something that can burn 4000 watts to produce a gas that you'll only get around half the energy back from when burned. Also stainless electrodes means you'll be turning some of the chrome in the anode into carcinogenic hexavalent chrome in your solution. Perfect.
You are way to kind with "around half", calculated he has about 16% conversion efficiency assuming this is pure gas without water vapors in it and this is on the heating value of the gas created.
Thank you for highlighting the energy this device waste to produce a small amount of hydrogen / oxygen mixture
Todavía hay gente que fabrica estos componentes yo arme uno y hasta hoy no pude terminar ni probarlo al máximo primero que mi auto justo dejo de funcionar y probar su efectividad con transfirmador también es trabajoso seguramente funciona pero yo todavía no pude
You give more than you get. What's the benefit? The cooling problem is also a gift.
Use fiberglass bolts to hold the plates together. You can get fiberglass closet bolts, used to hold a toilet to the flange.
The great thing about a 4000 Watt hydrogen generator is that after you pump that hydrogen up to 10,000 PSI, store it in a tank and then later send what hasn't leaked out to a fuel cell you get 1400 Watts of power back. What a great deal!
good job . good effort . room for improvement . careful . oxyhydrogen is more volatile than petrol . my question is : in another video . 1 ) show us you close the petrol supply and run entirely on oxyhydrogen 2 ) also before & after physical appearance of stainless steel plates & water .
The car will not run on Hydrogen, there is not enough of it, to run even a small car of a generator like this you would need one the size of a truck, this generator would not even run a lawn mower.
an American fellow did this back in the 70s on a 125cc bike (don't think it was Meyer). it ran well for about 20 mins then started to fail. I believe because petrol despite being fuel lubricates the pistons to some extent. without this the pistons just get eaten up from the friction. also requires radical timing change as HHO is implosive, not explosive. hence why most use only as additive :)
@@chronicsys Petrol in the 70s was also full lead, this increases full density and it is also an upper cylinder lubricant. That same motor would not like current unleaded fuel either. It is not hard to make a motor run on gas, I have had several cars that run on LPG but Hydrogen is 1000 times more difficult to use than LPG. As I stated before simply pumping some gas down the air intake of any motor does not help anything. Hydrogen or HHO is not implosive, where on earth did you get that rubbish from.
Nice to see your video. God bless you
I look to be easy but very dangerous. 😮thanks your experience explain. ❤
Brak tulejek separujących płytki od śrub...
Верно, я тоже это заметил, должно было коротнуть, болты не изолированы от пластин просто тупа в ставлены текстоливые шайбы и плюсовые с минусовыми пластинами находятся в К. З
Center bolts should be plastic! Or in a insulated tube
yeah, he had bigger holes in the Neutral plates but I know what you mean, if any of those plates move and you "shorten the Voltage line you could get extreme amps instantly.
Wow ur bolts are not short circuiting. I m interested in such bolts only. Forget hydrogen.
The added oxygen, O2, that is produced along with the hydrogen causes the oxygen sensors on the car to increase the fuel injector duty cycle which causes an increase in fuel to the cylinders which increases the RPM and gasoline consumption.
It's a carburetor car no O2 sensor
@@davenorman8251 Thanks. I didn't see that.
would love to hear how your project goes when you refine it ,i think really need to reduce that voltage though as 48 will be had to integrate into car in the long term
You do not want to put crap like this into your car ...You will use around 300 watt hours of energy to produce around 2 watt hours worth of hydrogen. Your fuel consumption will actually increase. ... this example would not even produce enough Hydrogen to run a lawn mower.
I actually agree with that. Its not really saving energy unless you're converting it with solar. Cuz it takes to much energy to make it. Unless you ues aluminum. Which is consumed as a chemical reaction. The best way to convert it is very slowly. Wich is fine if you can store it.
I like that it runs clean. And is very clean for a combination motors to run on. I'd love to run a nitrogen set up with my car to run as part of the fuel mixture.
@@CalebGibbsAvenue Why would you want nitrogen ? it is an inert gas and it will hamper combustion. How would you tell your ECU that you have nitrogen or Hydrogen going into your motor ? How would you calibrate your O2 sensors ? Yes Hydrogen is very clean, the biggest problem with it is that you need a lot of it and a motor specifically designed for it. That car would also need a maintenance schedule that would rival that of a fighter jet. Hydrogen is very hard to store and needs a special tank, spaceX or NASA might be able to help you out there but it might cost a bit... good luck
I meant NOS. Obviously, it's not that one. So far as regulating it I'd just use a propane regulator. But onistly I'd have no idea if it work. Just a thought. I'm merely describing the set up I have in mind.
Is this producing a mixture of hydrogen and oxygen gas? Also, do you think it would be difficult or effective to connect some sort of system to circulate the water to a bigger take that has ice in it to keep the temperature down? Would that help the first design work better without increasing demand on load?
That's a Wet Cell, electrolysis start at 1,5 Dcv,if you are putting 12Dcv you are getting, home water heater, after 1,5 volts the rest of the voltage is wasted and goes to heat up the water,
E=MC2 is just a joke!! OMG: Let's get educated #1. The most powerful part of a magnet is the center!!!, #2.The entire universe is magnetic. If it weren't for the center of a magnet AC current could not travel nor radio waves. FACT!! #3. If you want to play with anti gravity it's right at the center of a magnet!!!!!!!!!!!! TRY THIS: TAKE THE CENTER OF A BAR MAGNET AND TAP IT ON ANY NONE METALIC MATERIAL>> YOU DONT WANT TO DISRUPT THE MAGNETIC FIELD WITH ANY IRON>>> You will see it will loose about two thirds it weight.. Most UFO'S are not detected by Radar because they are none magnetic . Not in the North South pole thinking!!! IT'S ALL ABOUT THE "CENTER" get your act together. You need get past the North and South pole thinking..they are the weakest part of any magnetic field!! We all got screwed in the early ages by Edison and D.J. Ludwig. They would not allow Tesla to expose the center of a magnetic force and all the benefits to man kind. INDUCTANCE IS THE OSILLATION OF THE NORTH AND SOUTH Fields VIBRATING IN THE CENTER Field.::: The height of ones intelligence is directly proportional to their own realization of their own ignorance111111111111111111
@@vincecox8376 what are you talking about? If you’re questioning my intelligence, I’m no Einstein but I am also not an idiot. I work in the power generation/transmission industry and have for 15 years but my knowledge is limited on this kind of stuff which is why I’m asking questions to try and better educate myself. Are you a bot? Unhinged? Or just trying to swing your dick around at random people?
Этот не передаваемый запах хлора!🥰
Aqueous potassium hydroxide is employed as the electrolyte in alkaline batteries based on nickel-cadmium, nickel-hydrogen, and manganese dioxide-zinc. Potassium hydroxide is preferred over sodium hydroxide because its solutions are more conductive.[18] The nickel-metal hydride batteries in the Toyota Prius use a mixture of potassium hydroxide and sodium hydroxide.[19] Nickel-iron batteries also use potassium hydroxide electrolyte
Thanks for Upload this Video ! You can increase hho production enormously if you sonicate the water to be split with ultrasound. There are now reports that this method increases the hydrogen yield by a factor of 14. Or you can reduce the energy required in this way.
Nonsense! This is just wrong info - also in the mentioned video!
Have you tried that? Australian researchers have tested this possibility with ultrasound and achieved an increase in yield gas. That was in several news channels, not only to read on KZhead.
@@DJENERGY63 ultrasound frequency range is 2 to 18 megahertz. I used 8Mhz and I only get 2% extra, with same watt. Do you suggest a spesial hertz number
@@H2ON_MEA The question is, how do you bring in the ultrasonic frequency? As far as I know, the Australians installed a piezo speaker at the bottom of the electrolysis test rig, driving the sound directly into the electrolyte. The frequencies are me currently not known, but I would try 20-60 kHz. Power anywhere up to 10 W.
@@DJENERGY63 I see . Thanks for that information. I was pulsing the DC in 8KHz . So it is derance than you ment . Can you please right the name of the video from the Australians piezo speaker to search for it 🌹
You are creating highly explosive mixture of hydrogen and oxygen
I wonder, what is the energetic efficiency of the hydrolyser? I have read that simple hydrolysers are around 50% efficiency. It is quite a science to rise the efficiency to 80%. Right plate material (Platinum maybe), right water solution with some salt or base like NaOH, right voltage and current on the plates. Plus hydrolyser water filling system, as there will be some pressure inside the hydrolyser.
Where did the electricity to charge the battery come from?
Hydrogen fuel cell?😁