DIY: How To Restore a RUSTY Truck Frame LIKE NEW with Basic Tools!
#Eastwood #PowerWagon #Restoration
Check me out on Instagram @PartsAndRestoration
Today, I’ll show you how to restore the steel frame of your rusty old vehicle using a few basic hand tools and some
great products from Eastwood!
My 1958 dodge power wagon lived a hard life as a landscaping vehicle before I got my hands on it. After stripping the frame down of everything attached to it, scraping and washing away all the dirt, I was ready to restore the frame to its original glory. I wire wheeled the frame down to bare metal and gave it a thorough degreasing with Eastwood’s Pre Painting Prep. With the surfaces prepared, I applied Eastwood’s Platinum Rust Encapsulator. After a 4 hour cure time, I applied Eastwood’s internal frame rail paint to encapsulate the rust inside my boxed in frame sections. Lastly, I applied Eastwood’s 2K Aerospray Chasis Paint in satin black. I couldn’t be happier with the result!!
---------------------------------
Links to everything I used:
Platinum Rust Encapsulator: www.eastwood.com/eastwood-rus...
Internal Frame Paint: www.eastwood.com/eastwood-int...
2k Aerospray Chasis Paint: www.eastwood.com/eastwood-s-2...
Pre Painting Prep: www.eastwood.com/eastwood-pre...
---------------------------------
Music Credits:
Idle June by Schematist | www.schematistmusic.com
Music promoted by www.free-stock-music.com
Creative Commons Attribution 3.0 Unported License
creativecommons.org/licenses/...
San Fran by Schematist | www.schematistmusic.com
Music promoted by www.free-stock-music.com
Creative Commons Attribution 3.0 Unported License
creativecommons.org/licenses/...
Time Dust by Schematist | www.schematistmusic.com
Music promoted by www.free-stock-music.com
Creative Commons Attribution 3.0 Unported License
creativecommons.org/licenses/...
How many cans of the 2K did you use?
5-6
That 5-6 cans, was that for one coat? Looking to use Eastwood 2K on my 1971 Monte frame and trying to figure out how much to buy for 2 coats. Thanks
@@tommik9368 Rattle cans give lousy coverage. Just use a spray gun, cheap enough and way better.
Hey Bud I’m looking to do an off frame build on my 68 C-10. I know the frame is still solid. But for future reference if I run across a project to where the frame needs a lot of work including patch work do I need to pass that project up or do I go ahead and spend the extra time on re-enforcement and bringing it back up
How much did the entire Eastwood stuff cost?
That frame is mint. Up here in Maine we make frame restoration videos on 2010 gm products 😹
Hahahahahha
I'll watch your video if you do not ad the extra crappy music or any music.
i was gonna say the same thing. try that here in upstate ny. had a 2013 the other day, almost time for junkyard
nice job though
Here in England we do the same on 2010 Land Rover vehicles!
There are lots of products out there to "peel and seal" frames now, but you get "props", for the wire wheel, manual labor, sweat equity approach! Some people don't have the work ethic you do, congrats!
Thanks bebo. Better to do it right and extend the life of this old gal
So true
You only have to do it once. If you do it right.
@@nicolec7290 That's the "thought" I live by, but not always the way I work, unfortunately! Ha Ha
I love your videos, keep them coming! I don't know anything about restoring an old car or truck so I appreciate all the little details in your tutorials (equipment, sprays and products you use, etc).
I like the mild humor and trying to make your videos fun. That's a lot of hard work and dedication you put into the frame. I can't wait to see the finished project. Keep up the good work and awesome job demonstrating some great products.
Brutally well done ... Always cool to see ppl giving old trucks a new lease on life...
Nice job, very thorough. I'm getting inspired to do my '55 chevy frame. My first frame off. Got a rolling frame looking at me. With winter coming, admiring your garage space too. Thanks
Your trick with the 2 pressure washers was nothing short of amazing & hilarious!!! You were levitating there for a few seconds. Awesome
Just scored a frame for my '92 F150 restoration project, so that's what brought me here. Its videos like this that keep me inspired to keep moving on my own projects, so thank you for that.
Restoring a 1991 f150 , I’m having trouble sourcing a new long box to replace the rusted out one
Wish someone would have shown me that hand-clap clean-up trick years ago. Would have come in handy. Kids today got it easy...
Haha you said it brother
My man. You are one dedicated hommie. Frame looks brand new
I like how you did the silver Rust Encapsulator on the bare frame, then the black 2K top coat. Makes it a helluva lot easier to see where you've painted, and where you've missed. Good subliminal tip!
I'm starting a '57 Studebaker 3/4 ton in similar condition this year. I needed to see this. Lotta work and a good job. Clever subliminal. Glad to see you ended the video the same way you started it; Murphy's. It's the best Irish stout. Thanks.
Good effort on the manual labour. I use one of those air varsol sprayer's to spray rust inhibiter inside a frame, it comes out as a fog and gets everything inside coated including seams.
When spraying inside your cross members,If you put tape about a inch from the end of the rubber tube,you will know when it is close to the end pulling it out. I hope you did not get any over spray on your truck parked in the doorway,you might want to cover it up if you spray again. You can buy a roll of plastic at the auto paint store,it's around 14' wide and 300' long to cover your projects with. It turned out great! Nice job.
Living vicariously thru these videos man. This is one of two cars I want to rebuild. Keep it up!
Always can appreciate a mans hard work and still have time to create these great videos
Just wanted to say that the level of your preparation is first class, Clearly you work to exceptional standards,
Wow that’s really kind of you to say. Thank you
Very nice!! Thanks for letting us know how much rust encapsulation you used. Would also be great if you can share quantity of other materials used. And, especially, how many hours of labor did it take you to do this frame restoration project? I enjoy doing projects like these but find I’m always underestimating the materials and time to complete...
Enjoyed the view, showing an average Joe with the bare basic tools performing a great job and enjoying the project...Eastwood is surely a company that is DIY friendly with tech support and easy to use products. Thanks again for the video and looking forward to more progress
You have a lot of patience and endurance! Very nice job!!
I did one 1940 Ford coupe frame at the same time as a 1957 Chevy ragtop frame...side by side. We sandblasted them roughly to knock off most of the rust and then sprayed both with a metal acid from Zep. Then repeated both steps the next day. Then sprayed heavy coats of epoxy primer, waited six hours and gave them another prime. Then sprayed catalyzed acrylic enamel black, numerous coats to get the shiney look. Even clear coated with a catalyzed urethane clear. Two years later, when we had both of the bodies finished and dropped back down with the engines, the frames looked fab. 34 years later, in 2018, the man who still owned both cars called me to come inspect the acrylic lacquer finishes (Ditxler). Even though both cars had been driven to various shows, but were lept in his barn most of the time, I got down on the floor and flashlighted the frames. They were still 100% and still shiney! Compared to the coal tar based black enamel the Ford factory used and the black alkyd enamel GM used, they really proved the better, doing it how we did. I hope I never have to do another frame, just like I hope I never have to hang another front clip on a '50 Chevy truck.
Dude. You are a beast. The frame restoration video was awesome! It’s about time someone did it right....And you didn’t even need expensive equipment.
Haha thanks. Gotta do it yourself how you want it done
Great Scott you sure did a awesome job on that frame! Hope to see more.
I have to say, you are a hard worker and don't mind doing the hard stuff. Well done, good ethics!!
You need 2 engine stands converted to frame holders which when you weld flat plates to them they can bolt straight to the frame on the front and back allowing for you to roll it around and also spin frame 360 when painting it. I have an buddy who did this technique for his 63 impala
Genius 👍
This is a huuuuge job, and the job done was absolutely perfect. There is not much more you can do to make it any better
Thanks brother! Labor of love!
True!! It was a lot of work. It looks GREAT. Right now, I got a 79 F 150 Styleside that my dad had new before I went into the Navy. I retired from the navy and been working on it. Engine, transmission and differential done. Time to put this puzzle back together. Real fun!!!
The frame looked rust free from the start. Nice
Remarkable work. Thanks a lot Dave, I really enjoyed watching and learned a lot at the same time.
Appreciate your hard work and talent on make old like new brother. Semper Fi!
I lost it when you walked through barefoot 😂
Mission accomplished
Me too. Shorts are bad enough.
Who doesn't want to see someone else work their ass off like that?! Good job!
Haha. You got it!
Brother ; I appreciate all that work you did. The end result was amazing… Keep doing what you do.
Love the level of humor and chill in this video. The pressure washing part had me cackling for a while
So ridiculously satisfying seeing all that rust and shmoo come off.
Yasssssss. It was fun!
Nicely done. That is exactly how i'd do it if I had somewhere to do it. I've got a few projects waiting for a shop to get built. Hopefully 2021 will be the year. Smart move using the silver chassis paint. Makes it easy to see if you miss any spots with the black top coat. I plan on using the Eastwood products when I get around to doing the frames on my squarebodies. I May even do the frame on my 57 Two-Ten but not sure yet as it's a little too nice to tear apart just yet.
Thanks brother. Good luck with yours. Get that shop off the ground ASAP. You only live once
That's a lot of work, but well worth the time invested. Great job !!!
I wish I had that much room to do my truck, nice work on the tidy up will look great when it's together
Brave man, spraying with your GMC parked 20 feet away in the doorway. I would be so worried about the drifting overspray speckling my truck 🙂
Haha. I park the truck to keep random people from walking into the shop (when I don’t, they do) 🤷🏻♂️🤷🏻♂️🤷🏻♂️🤷🏻♂️
@@partsandresto Just hang a sign that says "Warning: If you walk into my shop, I will paint you as well."
@@partsandresto I figured the GMC was parked there as a deterent, I would have done the same as well although would have also been worried about the overspray loool.......great job man, really hard work although really rewarding work! I have yet to try the Eastwood products although have had great success with Rust Bullet sealers and rust inhibitors, have you ever tried them on any of your projects? would be interesting to see between Rust Bullet and Eastwood which if any is slightly better than the other, Cheers bro
dries in air before reaching it
Most overspray will dry in mid air before touching the 20 foot mark leaving it easy to wash off so don't worry about it just paint and realize that there's an reason you hold your paint gun 6 to 8 inches away cause it gose on wet from that distance and sticks 20 feet is plenty room to get it off your truck I paint houses ,cars ,rod iron fences and have never got anything on my truck that wouldn't just wash right off. Good day to you guys and yes house paint is designed to stick to metal as well as wood and stucko also.
Looks good. Just need to remember to use a breathing apparatus at all time when dealing with aerosol and eye protection especially when your working under something like that frame when brushing on the protective coat.
Yes sir. I’ve since learned
@@partsandresto perfect job, just whispering here, next time if possible, cover that nice ride by the door from all the paint, man that frame, well done
@@partsandresto very thorough and nice job. Mopar lover myself. When you were doing the last part with the frame on its side, you can see the air currents (looks like) moving through the shop toward you. Wear painting respirator for this people. Those painting products are not made to be inhaled even in small amounts. Stay safe and GOD Bless.
Thats total dedication n pride to what u do
Love that inside spray. I’m planning to box a frame and I’ve been marinating for a while on how to get it painted inside!
When I was growing up, a farmer near me was always bragging about his KB-46 flatbed. That was back in the '60's. He had it many years.
Awesome. I bet it was sick
Wow Dave! Looks like an epic couple of days! The first day seemed to be a long one. Definitely, Great results 👍 Frame looks factory fresh. Love your videos, entertaining, informative; and well done! Look forward to all of them!
Thanks Paul, I shot this over two days and yes, day one was intense! More on the way sir.
New to this channel and I love to explanation about what you are doing and the products you use. Going to be doing my truck next year so I am looking at what others are doing and how they are doing it. Well done and keep up the great work!
Wow that frame looks fantastic 👍👏🏆
I know this truck. I’m looking forward to watching this project through.
Yes sir. More to come
I wonder what todays truck frames will look like in 63 years? Somehow I doubt they'll be anywhere near this nice! That's good old AMERICAN steel.
encapsulate the rust sounds like a time bomb. What will really stop surface rust in a cavity is lanoline grease (fluid film)
Not only a great frame restore, but that is a cool ass building! It has awesome character!
Nice job! Looking to use the same product on my F-350 frame. Curious how the finish was after brush coating the platinum paint.. Did it leave any brush stroke imprints or did it sort of self level and come out as a smooth finish when dried? If not, would you suggest using a spray gun instead of brushing for a smooth finish look?
To be honest it’s a little brush strokey
First ever video I've seen of yours and honestly it was awesome. Great job on all that hard work. Only thing I would have for criticism is typically when painting you do a really light first two coats allowing the material to flow and adhere better to the frame. I don't know if you'll have any bad effects from going so heavy right off the bat but I know that with everything I've painted going two light coats then a medium coat always serves me well. Cheers my guy
Thanks Ryan, that’s good advise. I’m literally flying by the seat of my pants
exactly
Nice to see a fresh website with a lot of pro tips!
This is therapy for me. 😁👍
This is one of the best frame restoration videos I’ve seen!, I subscribe to your channel!
Welcome brother!
Makes me wish I had a shop big enough to do a frame off resto. But for now I have to fake it. Doing the best I can for now. Looking awesome! Subbed and following along. Glad this showed up in my feed! Keep up the good work. Remember us little guys when you hit 100k subs. 😜🙌🏼
A thorough job. Good on Ya! Thanks, JD
Thanks brother!
I’m building a willys wagon with 1-ton Chevy gear & you’re approach is pretty much identical to mine. ...& that shop you got there is the real deal, I built my first hot rod in a barn & stuff like that gives everything we do a real charisma, I love it!
Yes sir, that’s the way to do it!
That frame was almost perfect to begin with
This was a nice video to watch. I'm in my shop by myself and watching you do exactly what I have done. I can relate to all the frame challenges. Good luck with your builds!
Thanks Scott!! Glad you liked!
Totally freaked out by sandblasting. Happy to see this process is totally legit.
You did a good job it looks great! I like the yellow cab hanging in the back. Wish new trucks were that cool.
I like the shop, looks like an old bootleg hide-out from the old Capone days.
Haha. 1924 built. Probably was
RE:Michael Carron. Yeah, I was thinking same thing. Neat looking!
Michael, Shhhh don't tell anybody, the vaults in the back! Ha Ha
@@bebo5558 Look at the brickwork, any changes in the mortar or bricks? That's the Vault. I would appreciate a finders fee for the loot. Lol
Looks like Philadelphia
When you painted subscribe ok n the frame I subscribed . Looking forward to seeing this build and the rest of the channel
Deep dive my friend. Welcome aboard 😂
Tub-0-Towels should be proud ! Awesome &informative..👍
So satisfying!
Hydro blast would have taken that frame right to the ready to paint stage in about 2hrs. They come to you, look into it. Maybe for the next project.👍 Great job on the frame!
Thanks Jim. Good ide
@@partsandresto As I get older I start to realize that the one thing I can never get back is my time. So I tend to contract out undesirable task. 🤣
It’s really interesting how a truck frame from the 50’s is so solid and the frame on my 96 Silverado is literally flaking apart. It’s so bad that a had to have 2 cracks in the Chanel repairs with diamond plate and 1/4” steel on both sides of the frame by the front spring eyes. But I do like Eastwood’s products and may try them out on a 79 trans am frame I’ll be restoring.
Yeah they are great. Worth a shot, you’ll be glad you did
Its not from the northeast that much is certain.
Looks like a satisfying end result.
Turned out great!
Wish you were near by, I would enjoy helping. Would make a nice practice run for Dad's 53 B3PW sitting in my yard.
Yeah this is exactly the kind of project where I'd happily help for free
That 1958 frame started out in mint condition compared to my 1994 GMC k1500. And you made it even better. Great Job!
Absolutely beautiful work
New subscriber here, I started working on my late Dad's 1971 Chevrolet C-10. There's some rust on the frame but mostly on the rear half of the truck frame, glad I found this video and now know what to do. Keep up with the cool Videos 👍🇺🇸..
Well this frame looked rust free to start with, try 15 years in Michigan.
No thanks!
I can relate I was born in Ann arbor Michigan and raised in Ypsilanti
Born and raised in Jackson, MI.. Work in Ann Arbor and Ypsilanti.. LU 252 master Electrician..
RE:william reid. Yeah, that frame looked pretty darn good compared to my 92 GMC from the "rust belt", Michigan, USA.
Downriver Michigan sucks for frames too😖
Nice job, I went with their middle of the road encapsulator about 8months ago and not entirely happy with the outcome, have you noticed any small bit of rust/oxidation coming through? I did alot of the same steps in the video and also did two coats of each product and feel like it should have last alot longer.. may gas tank skid is where I noticed it most. Maybe I should have used the 2k instead of the chassis black, hope to see updates, awesome looking frame brother!
Thanks Adam. Can’t give a down range report yet as it’s still been indoors the whole time. No issues noted yet
I used the Eastwood black encapsulator on my 95 Chevy truck frame. Have the same problem with rust coming back though it. And frame has been mostly stored in my garage.
@@nineten123 yeah, I think I'm going back to self etching primer at this point... I live in Chicago and we have yet to have snow/salt.
I am in the process myself with my 1936 dodge brothers truck , hope to have good results as well , great video
3 bangers in here too, I love the music haha
This man is a gluten for punishment. I envy his ability to stick with an long and boring task to achieve an excellent result.
Not happy about that flappy coat when using the angle wire-wheel. Great project though superb job 👍🏻🇷🇴🇬🇧
Haha. Yeah it was a bad idea. Had an incident, didn’t die, but I pooped a littlw
Absolutely love your shop !
seeing a lot of improvement in the quality of the videos, nice work. This one feels like you're catching your stride...good for you. dig the project.
Thanks Norman!!
Subscribed ! Fantastic video, what’s the music that you’re playing sounds really cool. Great work mate. 👍
Hmm, music should be in the description. Welcome aboard.
Great workspace, how did you get that?
I found it and bought it cheap before the neighborhood turned around
This was incredibly satisfying to watch! I'm curious, how much do you think that frame weighs on it's own?
You are very meticulous and detail oriented. I would never have the drive to do all of this. 👍🏻😁
Haha. Those words have never been used to describe me before. Thanks hahaha
@@partsandresto you’re welcome. You’re definitely a hard worker that does great work!
The music makes me feel like I’m on hold with my mortgage company
I had an old boss who would get on the phone with her mortgage company at work. I'd hear her in her office basically begging them not to foreclose 😥 it's no joke out there, take care everyone
@@reallyhappenings5597 well I was referring to the music being overwhelming generic 😂 but to address your comment...she must have had a shitty lender 🤷🏼♂️ my lender takes whatever you can afford and defers the balance to the end of the term...thankfully I haven’t had to use this option yet...For now I still make a good income but I know many are only a paycheck away from absolute ruin 😔 all over the common cold too 🤔
Started breaking a truck down today. Strange how big brother put this in my feed.
Haha. Welcome to 2020, that’s how they get ya
They listen using our phone be aware of what we discuss around it.
@@udkiannarajrajathinagaran4463 no doubt. I'm ready to go back to a campbells can and some string.
Looks like in exceptionally good shape especially for a 1958 Dodge.
Man, you work hard and the end product will show it!!!
Thanks brother
A lot of work but well worth preserving the build!
That’s it brother!
Sand blasting would of been way quicker I think. Damn I want to know how to get that clap cleanup to work, I try it and it doesn't work. Lol
You do great work man! I'm still looking for my truck.
Good luck bud, don’t let up, they’re out there!
I'm all in on the choice of refreshment dude slainte
I wish frames were coated like this straight from the factory
You’d think they would be!
Dude! you REALLY need a 3M respirator when using that spray paint, especialy the 2K types.
I’ve since learned. Never again
Thanks for sharing great work.
great work Sir you did well excellent workmanship.. cheers NZ
Is this for hobby or is this your profession/self employment? Reason im asking is because i love stripping cars and trucks down to frame... if so how did you get started?
Just a hobby, I’m a full-time fireman. I got started by just giving it a shot, this is Quite literally the very first truck I have begun a restoration on.
@@partsandresto thats pretty cool.. so is my '82 Chevy.. very 1st one of my own im taking all the way down to the frame.. its therapeutic to me a bit, idk why but it is.. are you in NY, NJ or MA?
Love your vid. But Dude, wear a proper respirator when you're spraying 2k paints! A dust mask doesn't cut it!
Wow you did a great job. Congrats.
Impressive, that's a lot of work, but it looks like it will be worth the efforts! Looking forward to the rest of the build!! Good luck!
Thanks Patrick! Stay tuned!