DIY for changing Hydro Gear Oil for more info 4 qts of 20w50 SM, SL service - Motor oil www.hydro-gear.com/service-an...
Пікірлер
No life story. No waffle on about how your morning was. Just straight to instructions. Very good.
@aussiewelder61303 ай бұрын
Finally someone who gets to the point does the job shows it clearly and doesn't want to act like a puss about it. Someone who isn't concerned about every little freaking detail and worried about being critiqued by the world. Thanks brother
@durdyryder19 ай бұрын
Great video now I can skip the dealership
@nelsoninman36782 ай бұрын
Thanks for the video. This is the same procedure for the Fastrak SDX too. Same filter.
@aquaman01673 жыл бұрын
Thanks for the video, quick easy info. 👍🏻
@timbeech23174 жыл бұрын
Thank you very helpful... I will be doing this this weekend.
@PaulGruhn3 жыл бұрын
Great video! Thanks man!
@theinternets75164 жыл бұрын
Thank you for your great video you saved me money
@oscarchavez8512 Жыл бұрын
Thanks for the video!
@WeSRT43 жыл бұрын
Great video
@321CrashandBurn8 ай бұрын
The hardest part of this is removing the vent bolt and getting it back in.
@AmericanConcrete7 ай бұрын
Very helpful! Thanks!
@scubasteve30322 жыл бұрын
“Oil filder” haha
@followtherabbit2032 жыл бұрын
Good tutorial 👍
@luisbarcenas5330 Жыл бұрын
Good vid. I actually found it easier to reach in just behind the deck and across to get to the top vent bolt. Had to work each pump from the opposite side for best results. just FYI
@DerikStillPasinthrough4 жыл бұрын
instablaster...
@reeseimmanuel5262 жыл бұрын
great vid. Thanks
@mikemorris21592 жыл бұрын
It would have been nice if you had used a light taking vent plug out
@user-sr8qj4of6d7 ай бұрын
Great video, question though. It always I have a minor leak from one side. It appears to be leaking from a circular piece towards bottom of transmission. In your video, looking from the left side, just to the right of the filter is a brownish circle, can anyone identify this?
@njaimet Жыл бұрын
Great video man, made the change smooth and easy. Once complete, it was whining as I rode it around, does that whining eventually stop?
@josephsepulvado20483 жыл бұрын
Check your reservoir to make sure it’s not low.
@arubanjames2 жыл бұрын
A recent URL would be nice, as the one in the video doesn't exist anymore.
@vanstry3 жыл бұрын
Great video. Where did you jack the mower up?
@WBOS723 жыл бұрын
I'm wondering the same thing. I can't seem to find information on where a safe place is to do this on the Raptor SD.
@joek99622 жыл бұрын
On the back plate. On the hitch hole
@Four2NineProductions Жыл бұрын
Couldn't see how you have it jacked up. I assume the mower needs to remain level during this process?
@MrAirtaz4 жыл бұрын
I use a floor jack on the back metal plate, and used jack stand visible in the picture of the vid.
@Four2NineProductions4 жыл бұрын
Can’t find my oil filder anywhere. All I see is my oil filter
@rickysheep934 жыл бұрын
LMFAO
@nexushexus43654 жыл бұрын
Nexus Hexus 😝
@rickysheep934 жыл бұрын
You say potato, I say badayda ...
@arubanjames2 жыл бұрын
I said it perfectly, you just hear funny 😁
@Four2NineProductions Жыл бұрын
ami hutler se le cai la banda del la bonba q puedo aser
@josemar71284 жыл бұрын
Do you put the plugs back in before or after you bleed the air from the system?
@vanstry3 жыл бұрын
Before you bleed the air from the system. Trying to bleed the air without the plugs in would have oil going everywhere.
@garyclayton47653 жыл бұрын
Put the plugs back
@Four2NineProductions Жыл бұрын
I have 130 hours changed the oil but not the gear oil and my reservoir is empty what do I put in that matches the factory hydraulic oil?
@trinidadrm Жыл бұрын
20W50 oil
@dustinowens980610 ай бұрын
Is it 4.1 quarts per side or is that the amount needed for both??
@thatflippinrabbit9543 жыл бұрын
4 Qt total should do it
@ElonMuskX3 жыл бұрын
Total
@Four2NineProductions Жыл бұрын
Does the whole system take 4.1qt or each side take 4.1qt?
@Stl5152734 жыл бұрын
The whole system
@Four2NineProductions4 жыл бұрын
it is recommended to use synthetic oil ?
@oscarchavez8512 Жыл бұрын
No
@Four2NineProductions Жыл бұрын
What size is your Hustler
@paruggeri4 жыл бұрын
60in deck shows at one point in the video
@RyanDiederich3 жыл бұрын
what size filter wrench is that?
@evelyn201 Жыл бұрын
65/14
@Four2NineProductions Жыл бұрын
last thing you said (is literally why i came here to watch this video) ... "again, uh, make sure you uh, check the fluid in the reservoir and make sure you have the "correct amount in there"""" :// what is the "correct amount!!!???
@user-se9tk3cn8p7 ай бұрын
Great video! And I love the position of your jack stands. Is there any need to be level for this hydro change ? Some of the posters asked about jacking. This guy has a nice clip of his opinion on jacking and stabilization. kzhead.info/sun/YJhtm7icgKtug4U/bejne.html
No life story. No waffle on about how your morning was. Just straight to instructions. Very good.
Finally someone who gets to the point does the job shows it clearly and doesn't want to act like a puss about it. Someone who isn't concerned about every little freaking detail and worried about being critiqued by the world. Thanks brother
Great video now I can skip the dealership
Thanks for the video. This is the same procedure for the Fastrak SDX too. Same filter.
Thanks for the video, quick easy info. 👍🏻
Thank you very helpful... I will be doing this this weekend.
Great video! Thanks man!
Thank you for your great video you saved me money
Thanks for the video!
Great video
The hardest part of this is removing the vent bolt and getting it back in.
Very helpful! Thanks!
“Oil filder” haha
Good tutorial 👍
Good vid. I actually found it easier to reach in just behind the deck and across to get to the top vent bolt. Had to work each pump from the opposite side for best results. just FYI
instablaster...
great vid. Thanks
It would have been nice if you had used a light taking vent plug out
Great video, question though. It always I have a minor leak from one side. It appears to be leaking from a circular piece towards bottom of transmission. In your video, looking from the left side, just to the right of the filter is a brownish circle, can anyone identify this?
Great video man, made the change smooth and easy. Once complete, it was whining as I rode it around, does that whining eventually stop?
Check your reservoir to make sure it’s not low.
A recent URL would be nice, as the one in the video doesn't exist anymore.
Great video. Where did you jack the mower up?
I'm wondering the same thing. I can't seem to find information on where a safe place is to do this on the Raptor SD.
On the back plate. On the hitch hole
Couldn't see how you have it jacked up. I assume the mower needs to remain level during this process?
I use a floor jack on the back metal plate, and used jack stand visible in the picture of the vid.
Can’t find my oil filder anywhere. All I see is my oil filter
LMFAO
Nexus Hexus 😝
You say potato, I say badayda ...
I said it perfectly, you just hear funny 😁
ami hutler se le cai la banda del la bonba q puedo aser
Do you put the plugs back in before or after you bleed the air from the system?
Before you bleed the air from the system. Trying to bleed the air without the plugs in would have oil going everywhere.
Put the plugs back
I have 130 hours changed the oil but not the gear oil and my reservoir is empty what do I put in that matches the factory hydraulic oil?
20W50 oil
Is it 4.1 quarts per side or is that the amount needed for both??
4 Qt total should do it
Total
Does the whole system take 4.1qt or each side take 4.1qt?
The whole system
it is recommended to use synthetic oil ?
No
What size is your Hustler
60in deck shows at one point in the video
what size filter wrench is that?
65/14
last thing you said (is literally why i came here to watch this video) ... "again, uh, make sure you uh, check the fluid in the reservoir and make sure you have the "correct amount in there"""" :// what is the "correct amount!!!???
Great video! And I love the position of your jack stands. Is there any need to be level for this hydro change ? Some of the posters asked about jacking. This guy has a nice clip of his opinion on jacking and stabilization. kzhead.info/sun/YJhtm7icgKtug4U/bejne.html
FILTER WITH A T
P