We will leave out the rate of torque for some strange reason.
@lambfactory25372 жыл бұрын
On the Toro 4000 with the ZT4400 torque filter bolt to 200 to 300 in-Ib.
@danaevans35243 ай бұрын
My Ferris z3x has these pumps but the vent port is an 11mm and it’s in a terrible location for a service item.. the bolt in this video was more like 3/4 so something must have changed.
@jonathantaylor692611 ай бұрын
You think you could have put the vent port plug in more accessible spot? Impossible to get out where it is located on the Farris z3x. Just saying.
@gregpendleton49573 жыл бұрын
Greg Pendleton same with the gravelys. Make it look too easy with the transaxle out of the mower🤦🏻♂️. Would like to see how it’s done with it on the mower
@damorej4163 жыл бұрын
Bobcat makes it super easy to access on the zt-6000&7000 series zero turns. Not really hydrogears fault it’s hard to get too on other mowers. The oem should make provisions for it.
@denverstaib10258 ай бұрын
@@damorej416 Toro 4000 with the ZT 5400 Very hard & tight to get to the vent plugs!
@danaevans352418 күн бұрын
I have a Scag Cheetah with the ZT5400s, I can remove the vent port plugs but it's a disaster every time I change fluid as I can never catch it just right, resulting in an overflow mess. You now include two threaded fittings and two short lengths of transparent hoses with each oil change kit..... I was hoping this video showed their purpose. It did not.
@pmtips44822 жыл бұрын
I have the exact mower you're working on. It would have been nice of you to mention that you can't easily access (unless you have smurf hands) the port vent plug without removing the transaxles. It would literally add 4 seconds to your video, making it an even 3 minutes, but saving me a lot of aggravation. I see a half dozen locations you could have placed the vent plug to make it much more accessible without removing each transaxle. Good grief.
@johnsagraves143 жыл бұрын
How did you end up doing it? I’m stuck at this spot.
@drake23hector2 жыл бұрын
Those vent plugs are extremely difficult to access so when you finally get a wrench on it do not completely remove it just crack it open a couple turns this will allow it to vent, hope this helps.
@timpope1221 Жыл бұрын
Hydro gear purge
@edwarcandy4648 Жыл бұрын
what size is the socket to remove oil filter cover?
We will leave out the rate of torque for some strange reason.
On the Toro 4000 with the ZT4400 torque filter bolt to 200 to 300 in-Ib.
My Ferris z3x has these pumps but the vent port is an 11mm and it’s in a terrible location for a service item.. the bolt in this video was more like 3/4 so something must have changed.
You think you could have put the vent port plug in more accessible spot? Impossible to get out where it is located on the Farris z3x. Just saying.
Greg Pendleton same with the gravelys. Make it look too easy with the transaxle out of the mower🤦🏻♂️. Would like to see how it’s done with it on the mower
Bobcat makes it super easy to access on the zt-6000&7000 series zero turns. Not really hydrogears fault it’s hard to get too on other mowers. The oem should make provisions for it.
@@damorej416 Toro 4000 with the ZT 5400 Very hard & tight to get to the vent plugs!
I have a Scag Cheetah with the ZT5400s, I can remove the vent port plugs but it's a disaster every time I change fluid as I can never catch it just right, resulting in an overflow mess. You now include two threaded fittings and two short lengths of transparent hoses with each oil change kit..... I was hoping this video showed their purpose. It did not.
I have the exact mower you're working on. It would have been nice of you to mention that you can't easily access (unless you have smurf hands) the port vent plug without removing the transaxles. It would literally add 4 seconds to your video, making it an even 3 minutes, but saving me a lot of aggravation. I see a half dozen locations you could have placed the vent plug to make it much more accessible without removing each transaxle. Good grief.
How did you end up doing it? I’m stuck at this spot.
Those vent plugs are extremely difficult to access so when you finally get a wrench on it do not completely remove it just crack it open a couple turns this will allow it to vent, hope this helps.
Hydro gear purge
what size is the socket to remove oil filter cover?
1 1/8”