Amazing Restoration of 50 Ton Hydraulic Jack || How to Repair Old and Rusty Hydraulic Jack
2023 ж. 22 Қыр.
437 378 Рет қаралды
Amazing Restoration of 50 Ton Hydraulic Jack || How to Repair Old and Rusty Hydraulic Jack
#hydraulicjackrestoration #restoration #oldhydraulicjackrepairing
Great to see these older tools being restored and not just thrown away. Plenty of more Jacks in the background ready for refurbishment, so there’s quite a need for it. 👍🏼
Often, people in the West throw out things that aren't even broken. They also would rather buy new than get something fixed. That's fine with me because I then get some free stuff. It's interesting how these guys specialize in only one thing.
Wow, that bench vice! Must be built to last for generations!
He needs to restore that bench grinder next!
Hadir JawaTimur saya senang kalau melihat alat2 yg sudah rusak di perbaiki 👍👍👍
You work with what you have, nice job considering, I’d have done it a bit different, but I’ve got access to more resources
Great job, 😊
Muy buen trabajo grasias por compartir..
Dude actually has a modern lathe. It's also clean to boot.
The old Ritchie Brothers overhaul I see
Great Work !!
Это не ремонт и не реставрация,это имитация работы.
kzhead.info/sun/h66PYdmwsKufqp8/bejne.htmlsi=BpcLbGGLp2TnU7zM
Good work 👍
inilah bezanya negara kaya dengan negara miskin. bagi kami negara miskin kami menghargai apa yang kami ada. selagi masih boleh digunakan kami akan memperbaikinya. kemiskinan membuat kami menghargai apa yang ada......
Surely the parts needed a wash.
Very good
He took the angle grinder,ground the outer diameter two different directions,then buffed the cylinder. I didn't notice him measure anything for out of round or taper. If it works ,he is very good or very lucky. Maybe he's a professional back yard mechanic.
He only ground the lift piston surface not the sealing area or the ring landings. Worst that could happen is a slow drift from scoring inside the cylinder walls. Better refurbishing than some others I’ve seen.
kzhead.info/sun/h66PYdmwsKufqp8/bejne.htmlsi=hhpvUUzQgpVDBXGz
That cylinder only uses pressure to extend, not retract. So rod diameter / taper is irrelevant in this case.
Machaalah
Dari cara kasar proses yg kurang teliti Saya kurang yakin pemulihan ini bisa bertenaga full seperti semula
What country?
Главное покрасить! Теперь можно смело сдавать в металлолом.
Show de bola
Молодец
This should work on 50 tons ? How long ? 2 minutes ? 👎
Repair cost of 2k thn buy new one 1k only😂😂😂😂😂
В конце жесть. Покрасили всё что есть собранным и грязным.
Это не ремонт!
❤❤❤❤
اعاده ترميم عفريته
Acho que esse povo não sabe o que são 50 toneladas.
Ну про 50 тонн это перебор, от силы 15- 20
Он ничего не поднимет потомучто это мусор😂
"... не ведают, что творят..." У каждого запасные глаза, пальцы, лёгкие. Идиотизм зашкаливает.
покраска 500лвл
रबड़ सील कहा मिल ता है बताओ गे
kzhead.info/sun/h66PYdmwsKufqp8/bejne.htmlsi=hhpvUUzQgpVDBXGz
дайте краски ЯВУ покрасить.
They haven’t heard about primer
Aapka adress milega
Do you not wash the parts before painting
Primer is prohibited in this country
WHy not oil treads all to do with cost
You mean 5 tonne ?
No way in hell this jack is 50 tons
I don’t know Rick I wouldn’t trust that Jack
I wouldnt trust these jack
👓👓👓👓👓👓👓👓👓👓
no under coat will rut in five minutes
Failure rate 50%, safety rate 2% , Job security 200%... Not sure if the parts are comparable looking at the work bench. i only pray for the soul that uses this... overall -20% success. peace
..................................fyuyy780knjhhhukkkkĵjjĵnlkjhyy89000 p 099 f h
❤😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😂😂😂😂😂z😢z😢😢😢😢😢😢😢😢😢😮😮😮😮rr5😅 pour 😅😅6 pas 666t qQQQQQQQAAAAAAAAAAAÀWWWWWWWXWXXXSSSZ
😊
15 ton !