How To Touch In Stone Chips Correctly, The best results for rock chip repair!
2024 ж. 15 Мам.
22 084 Рет қаралды
Unsightly Stone Chips? How to correctly repair Stone and Rock Chip damage on your car. Professional results for road debris damage and preventing rust from causing further damage to your car.
Learn in the video how to properly clean and treat the chip before the paint application process.
Preparation is key to ensuring a visually satisfying and long lasting result is achieved.
This video covers all bases and whole process can be watched in a step by step manor with text explaining every stage.
Excellent results!
Please check out www.paintgear.co.uk for DIY products, Kits and Detailing Products and accessories!!!
Help my channel, hit subscribe!
Great video mate. Something I’ll def watch twice
Another nice job. 😉
Cheers
My go to for chips is a prep pen/spot sanding pen. Highly recommend if you haven't tried it - it has a tip made of stiff fiberglass strands that allows you to sand all the rust and crap out of the chip very easily without marring the finish around the chip.
Yes mate this works well also 👍
Hey, thanks for taking the time to share such a great vid. I was curious, after the paint pen is there a protective cote after? I didn't see it? an then if there is do you mop and polish after application? Cheers dude, Lee
In this particular method (there are many) i just used solvent basecoat in the chips. In this method the polishing was done before. The touched in chip is the final finish
So can you mix a bit of base and clear ( making a single stage) to fill in the craters then also polish after too?
Have you got a link for that paint pen?
Great tips mate, did you wet and dry after filling with paint or just polished over the colour??
I didnt do anything after the touch in was done. This method is slightly different to others
Great to see your back with the videos i was wanting to ask you what do you use on the compressor for stopping water going into your airline when spraying i would be grateful if you could could help me thanks
Hi Brian its always a must to invest in a half decent water trap for this exact reason. Pipe it up in between your compressor and end of airline and ur good
@@cvrpov thanks so much for replying back you have been such a great help to me thank you
No worries Brian. Thanks for watching my videos
Did you use primer or clear coat on top of the colour coat? Sanding & polishing should be done as last steps also shouldn’t it?
Just colour coat mate. Adding primer etc is adding too may stages. Sometimes its good to add lacquer to the basecoat
Thank you. When the paint is spread, how long to dry and is it necessary to sand or polish ?
Leave 12 hours ideally
Come to my house and teach me how to fix my chips :D. Great video pal
Haha thanks pal
Can you show a video of doing the same to a silver metallic paint? I did it on mine but although it was paint matched the metallics turned out too dark/flipped to darker shade. Thanks!
Silver is a tricky colour I will be tackling in the future
@@cvrpov exactly and because KZhead has one old video it'll be great if you're the only person showing it right 👍 😁 I can't wait
Hi mate, could you show how is setup your van please?
Hi bud I've dont a part video on this but still adding bits to the van so there will be a vid down the line
So do you not need to wet sand after the paint to ensure its fully blends?
Polish the blend area. Wet sanding is to remove imperfections
Great video mate, I heard a rumour that paint gear might be releasing a paint touch up kit, with single colours or multiple colours and everything else needed for a repair, is this true? and when can we expect it to be available? Keep up the great work and thanks for passing on your expertise.
Can you put me on the pre order list for the paint gear touch up kit in black please.
Hi Will. Thanks for watching. Touch up kits are in the pipeline and yes you will be the 1st to recieve one. Martin @ CVR POV
What do you do if you applied too much paint to one spot and its dried and dripped? Do you wet sand it again to get rid of the drip mark? Lastly before i do damage...whats the grit of sandpaper what buffs out with polish? scared to go in with sand paper on my car haha!
It depends how bad the run/drip is. A big mistake people make is not using a low enough grit and end up rounding it off rather than flatting it. If its a very bad drip I've been known to use 600 grit, 1000/1200/1500/2000 then polish. Most runs if they are not too bad I can usually knock down and skip the 600 and 1000. If you burn through the lacquer then you will need to key up the area and apply more base and clear again. Ie repeat the repair process again. Make sure all paints are dried thoroughly before flatting and any re attempts at refinishing.
Nice one mate, Did you mix the paint up or buy the paint pen ???
I just use my own paint mate and an empty pen. Any paint can go in
I need the songs name please, great vid as usual
Thanks. Im not sure of the song name though sorry
So after you used the touch up pen what did you do to finish just leave it 😉
Yes. This finish is good enough. People seem to play about with it after touch up to make it right when I think preparation at the start is more important
@@cvrpov great stuff did you use clearcoat too or just polished in 😉
Please delivery in Brazil. Thanks
we are working on it
VW's are the worst ! My twin brother and I both had Golf R's, new stone chips every day. 2014 onwards, VW really cutting corners with paint application. New subscriber😁
Thanks for the sub 👊🏻
So you tell it’s so easy, no it cant be mate. #mindblowed
Ok sorry 😬
Where have u been it's been weeks,I was nearly going to jump off the gap.👍
Haha sorry mate. I have content, its just editing etc ive been busy with the Paint Gear site
@@cvrpov cheers
Easier to hide chip marks on white then metallic silver indeed.
Do you add clear coat on the repaired chips?
This will add durability yes
👍
Show us how to do this with a tri-coat paint, please. My car is in Premium White Pearl and I've tried like a dozen methods and they all suck balls :D
Hi mate, I may do a video in the near future explaining why touch ups wont work or give the perfect results people crave. Its a very colour dependant process and one method may not suite all paint colours and types. Your best bet is to make sure the chips are nice and clean and smooth (like in the vid), then the best method is to mix up some colour that is as close as possible using a base white with tiny amount's of black and a mustardy colour to change the colour slightly. Anyone with a solvent paint scheme can do this. I have touched in literally thousands of cars and tried everything and every method. This method works the best on pearl whites and 3 stage colours. It wont be perfect, but neither will anything else!
Thanks for the response! Maybe I'll just save up some money and get my bonnet fully repainted by a professional... :D
don’t you overfill them blade them off then polish them
That's another method. There are many
The video makes it look like all the chips have disappeared. There is no way you would get satisfactory results with the steps shown. You notice he never showed a close up shot of the repair. Waste of time.
I managed find an exactly the same white VW Golf and swapped them. U bust me
@@cvrpov Did you really? 😁
I done this as well but a bit different and it looks like it’s repainted even in the car shop they don’t see anything…
Check out www.paintgear.co.uk for DIY Kits and Products!