Full restoration a 1000 cc motorcycle racing car that was broken into 3 parts in an accident
2023 ж. 13 Сәу.
1 577 692 Рет қаралды
Full restoration a 1000 cc motorcycle racing car that was broken into 3 parts in an accident
Full restoration a 1000 cc motorcycle racing car that was broken into 3 parts in an accident
1) 1000cc with 1 cylinder!!??? wowwww.I’m curious about the make and model. 2) the broken parts of the frame looks like they were already poorly welded and broken again 3) false rust (over paint) which is only dried mud or rust effect paint 4) welding of the chassis without a geometry guide and with concrete bar!!!??? = unstoppable and dangerous motorcycle 5) grinding and welding of the piston without disassembly 6) reassembly of not cleaned motor inside (crank, gear box, cooling system....) and reassembly of cases without joints 7) reassembly of rusty camshafts 8) painting a dirty and greasy engine 9) poorly and dirty painting on tank disapears on final reassembly It's obviously not the same motorbike at the beginning and at the end. All that is fake. What you did to the broken motorbike will never work. You did'nt do restoration but massacre. Fake video.
Not a single gasket to be found, welding on aluminum with steel, probably improperly timed judging by the installation of the valves and cams. This whole thing is just OOOF!
honda cbr 150r
Thanks for saving me the time to write this up.
1000cc.... Sebuah kebohongan...ini seperti Honda CBR 150cc..🤦
Я это тоже смотрел на одном дыхании. Думал что они его обратно выкинуть должны в конце😅
His welding knowledge is overwhelming: the rear suspension, the crankcase, and finally the piston. I must have missed these techniques during my apprenticeship.
Im not too sure I would trust the piston, or the engine build in general. But hey they were not trying to break the bank on this restoration either.
Se suelda así para no agujerear la chapa y para dar relleno a un material muy fino
Halo my frends from indoneisa🔔🇮🇩
Это ужасная халтура а не как не реставрация!
I can’t be the only one completely concerned through out this entire video 😅
100% bodge
Should come with a health warning….built for entertainment purposes only 😂
i'm still waiting for the transmission restoration, feel like incomplete
6x10 warranty........6 miles or 10 minutes, prettyish on the outside, argh on the inside.......
38:01 😅pop 11¹@@mekko2012
A fairytale.Once upon a time there was a boy with a pile of junk.And he thought he could make the general public believe he could turn it into a motorbike.
But the boy had some nice tik tok slippers 😂😂😂
После такой реставрации его еще раз надо реставрировать!
Да тут весь канал - один большой троллинг "реставраторов" :))) Заварка поршня, приварка рулевой - вообще адъ и израиль :) Покраска по окислам и ржавчине, сборка двигла со ржавыми распредами и ржавой корзиной сцепы - бест оф зе бест! На фоне этих юмористов даже е.матвеев - лох колхозный :)))
Ты же понимаешь что это не имеет никакого отношения к реставрации и в конце ролика совершенно не то что он так усердно в тазике всю дорогу моет?
That is not a 1000 cc Honda. Possibly, a 150 or 250 cc.
Callate y disfruta
Kaha ji rahe ho Honda gold wing 1800 cc ki hai
@@punditsushilkumar39 13:06 ่บอล ่
mistake.100cc
This is sooooo fake 😂. Here we go again with the fake rust, just like the “computers” restorers…All rusted still inside and not a single part replaced.. what a joke
Damn.. 1000 cc with single cylinder😂😂
Những chiếc xe 1000cc sẽ có 4 xi lanh 😅
Man was showing off the gas tank paint job like it wasn’t the literal worst paint job I’ve ever seen holyyyy😂
I a novice body man. I did a repair on the front and rear of a van. Noone could tell I did a repair and paint feathering job. Until I went and traded it in. They saw it. That paint work was less than quality for sure.
Esa pintura esta muy mal. Es pintura que le cae gasoline y se quita utedes me entienden 😮😢
A moto do final do vídeo e a sucata do começo não são a mesma. Por que você acha que ele pulou a parte mais importante que seria recolocar o motor no quadro, religar todos os sensores e etc, e pula para a montagem das carenagens ? Um motor nessas condições não volta a rodar simplesmente com uma "limpeza" mal feita como no vídeo. Isso só falando por alto sem entrar em detalhes. Olhem por volta dos 30 minutos do vídeo como as carenagens pintadas sem lixar estão cheias de relevos e olhem na montagem final como a pintura está lisa só com uns descascados na pintura, da mesma forma o motor.
And more.. the bike to stay in that state of "decomposition" would only likely be possible to be immersed in water for years.. but, notice that copper wires (the face is dirty but the copper is perfect) rusty aluminum parts, rusty tires, and even rusty plastic? Where have you seen it? So nothing beats this video!! E mais.. a moto pra ficar naquele estado de "decomposição" só seria provável possível de estivesse emergina na água por anos.. mas, notem que fiações de cobre (a cara esta suja mas o cobre está perfeito) peças de alumínio com ferrugem, pneu com ferrugem e até mesmo plástico com ferrugem? Onde já se viu? Então nada se bate neste vídeo!!
Meu irmão, o cara deixou o motor enferrujado, preto, td encardido e sua preocupação é essa??
La supuesta moto restaurada y la moto final son totalmente diferentes. Me tramó su forma de soldar, no se cuantos preinfartos me hubieran dado si no fuera porque a leguas se notó el montaje :D 😁😁😁🤣🤣🤣🤣🤣
I could tear this thing apart really fast. But I could never put it back together. Absolutely amazing work, and memory of where everything goes. Not in a million years would anybody tackle this project. Thats what I thought anyways
fake restoration video
Sir everything is cover with video,After you take apart and see video,you will be able to notice all the part in the same place
Absolutely incredible. I would not have thought it possible. I like the way the hole in the piston was merely welded and not replaced. I would like to have seen a bit more on the work to get the engine running. I'm sure it wasn't just press and go.
nice
You need at least milling machine to make that piston work. I actually don't really believe this restoration, that bike was too broken to make it work that easily. A lot of parts of the restoration are not shown so they could have replaced a lot of pieces instead of restoring them.
With the power of TikTok flip flops and a fake supreme hat anything is possible
Двигатель данного мотоцикла собран по всем правилам механики, особенно заваренный поршень!
Почему наши умельцы не умеют так ремонтировать-заварил поршень, отмыл немного, зашпаклевал бак с дырками. а им все новое подавай?😀😀😀
дааааа, как он искусно дыру в баке шпаклевкой заибенил..... а.... уметь так надо
Меня убило когда он поршень стал варить!
This is going to be really interesting when they try to fix the forks onto the frame,
Qsq
this would be incredible if infact that was the same bike cause that clear coat on the tank was obviously not the same one in the video unless you sanded it all down again all the way down to the bondo
The tank looked like a milk dud when he finished painting it... 😂
@@jimg8887 Lol totally
this is fake restoration video. and that engine is done no way it'll run
Я не верю не одному его сварочному шву . Стиль сварки называется СРАЛА МАЗАЛА 😂
I love the rusty plastic and rubber lol
I think that's a Honda VFR 750F from the late 80s to mid 90s I had one back in 1998 that I used to go to college with . It was 1997 Red.
Wow, if this wreck (and that's an understatement) can be restored, anything can.
He welded the top of the piston. You can’t do that. He cobbled that bike back together. Wow. Well done.
didnt even take the piston off, filled the crankcase with spatter and filings........jeeze
It's hard to call it a restoration. I'm surprised he's wound up)))
More like a patch up
This is like one of those movies you show your friends knowing it’s bad but that’s what makes it good. I’d love to start another channel just tearing into these “restoration videos” lol
При сварке использовал в качестве посредника пруток арматуру периодического профиля? Ну хотя бы гладкий, или просто болт креплени какой нибудь
This super 👍👍 they were born with an engine in their hands .Not a Canadian or an American who would do that . Congratulations to him . 🇨🇦👍👍👍👍👍🇨🇦
Incrível a capacidade de restaurar uma moto nessas condições, Parabéns 👏👏. Se eu desmontasse iria ser jogado para o ferro velho porque jamais conseguiria montar de novo😂. Abraço do Brasil 🇧🇷👍👏👏
A moto do final do vídeo e a sucata do começo não são a mesma. Por que você acha que ele pulou a parte mais importante que seria recolocar o motor no quadro, religar todos os sensores e etc, e pula para a montagem das carenagens ? Um motor nessas condições não volta a rodar simplesmente com uma "limpeza" mal feita como no vídeo. Isso só falando por alto sem entrar em detalhes. Olhem por volta dos 30 minutos do vídeo como as carenagens pintadas sem lixar estão cheias de relevos e olhem na montagem final como a pintura está lisa só com uns descascados na pintura, da mesma forma o motor. Se for procurar detalhes tem muito mais.
E mais... Onde é que já se viu ferrugem em pneu, pessoas?
Eu nem acredito que assisti esse vídeo inteiro pra ter um final tão frustrante. Deslike👎. Mas quando vi a solda e a pintura mal feitas já sabia que não ia prestar!
Motos totalmente diferentes. O motor ficou deplorável, e da pra ver que se trata de outra moto
Братан, это не ремонт, а пустая трата времени. Они ничего там не поменяли, покраску производили по ржавчине. Раму сварили как попало. На этом мотоцикле опасно ездить
Contando con lo que tenía... Buen trabajo!! Eso sí, 2000cc😂😂
1000cc and only a single disc on the front? wow!!
1000cc!!!! I don't know? Whatever it is, great build. 👍
Best of luck wielding a frame back together! Good Luck!
Oh that piston is fully restored, a little welded and it’s like new. Ready to run
Я надеюсь этот парень еще живой))))
The hardwork is mind-blowing
Essas pessoas que restaura parece ter super poderes, uma moto toda queimada ele não troca uma peça aí a moto funciona direitinho esses ferro velho tem que contratar esses cara para conserta .carro é moto 😂😂😂
MY NEW FAVOURITE SOUND AT 20:8 😂
Total litas tingkat tinggi.mantapp bro.salam dari indonesia.👍👍👍
Много не показанно, по итогу видно совсем не то, что делалось на видео.
Да а ещё на спортбайке рама из профиля 20-20 ещё и шовная.👍
Truly a brilliant piece of fiction!
An absolutely entertaining sci-fi short film!!!! 😆😆😆
Luar biasa dari kondisi. awal yg sudah hancur bisa jadi seperti motor yg bagus tapi saya juga yakin pasti banyak spare parts yg diganti terutama di blok mesinnya. Jarang sekali orang didunia ini yg bisa membangun motor kondisi hancur sampai 90 % ini bisa di sulap menjadi motor yg bagus bahkan bengkel motor sekalipun. tidak mau mengerjakannya 😂😂😂😂 anda luar biasa 👍👍👍👍👍
Don't get me wrong, this is impressive the way they can put these things back together. But I don't understand why they feel the need to cover them and Rusty mud colored Goop to make it worse than what it is. 😮
I was thinking the same thing! We’re these bikes in a nuclear holocaust? These guys are good at restoring, but better at making videos.
мне аж страшно стало за того, кто сядет за руль этой адской колесницы)
The longer I watched this the more I thought this was too good to be true.
Pusieron el mismo pistón? Mismo cilindro? Solo limpiaron el motor? Mmm una acelerada y explota o ni prende
I believe this was fixed, made to believe it was all fixed but I reckon most was replaced and we are made to believe it was the same part that was fixed. Parts of the engine didn't even have gaskets and the bike towards the end is obviously a different bike.
Ese arreglo no me ha terminado de convencer
Es una moto diferente la del final xd
Good restoration of the 150cc I don't know how he did it but I lost half of the screws but the description of the video says 1000cc the bike lacked a couple of displacements or I enlarged the work a bit.😂😂😂😅😅
После такой ресторации этот мотоцикл сможет доехать максимум до той же приемки металла откуда они его забрали, да и то если один из них будет толкать этот мотоцикл
Why are there so many haters in this world. Let the guy do his own work in peace. It's not you it's him. 🕊️ Peace!
that engine restoration part was BS
Awesome little 125 project 😂
Very nice motorbike, congratulations
Absolutely incredible liars.)
There's no way that's the same bike
Желаем пацану успехов.И поофессионального роста.
What brand ..1000 cc one cylinder i think ..200 cc yarn
👊😊 ¡Excelente restauración! 😲 Pero.. ¡El vitropiso y la pared de su casa señor! ¡No los eche a perder manchandolos de pintura! 🤦🏻♂️
did i missed it or the gear box was oky
1 cylinder 1000cc holy crap
Exactly, 500cc at most
@@mariofabrizi5050 it is a Honda cbr150 version 2.
Hm, nasty. props for making it run. hard to call it restoration though.
This is all assembled, what a coincidence that everything he finds has rust that comes out even with water and it has all the parts
bro no 1000cc 4 inline yes 1 cylinder 250cc?
I'm really confused about the half job they did on the engine
Amazing job
1000cc for 1 cyl🤣, it's CBR 150 Thai 2014,.... however it's awesome works
Asombroso!!!la capacidad de encontrar otraoto y simular que la restauró 🤣🤣🤣💞
cada vez gente me sorprende que tonta que es👏tu crees que soldando piston sin desmontar a motor no pasaria nada? restauración del moto 0 y luego pintura sobre la grasa🤓
Ya te digo es muy falsa esa restauración, como que sea una Honda de 1000cc con un sólo cilindro...
гениально нах@й, больше меня в жизни ни чем не удивить, судя по тому как они красят раму, все идет по плану
I dont think its the same bike
Kawał dobrej roboty lecz według mnie błędne spawanie należało do środka przed spawaniem włożyć kontownik ponieważ obecne spawy puszcza i pęknie rama
technologia z lat '45-'70'/80' w polsce.
Wow i didn't know plastic can get rust.
Hermoso trabajo saludos desde El Salvador 🇸🇻
You need a sand blasting cabinet
Sound's like a scooter "A" for effort 👍🏼
Good jobs brother👍👍👍👍
This just proves it when you have nothing anything is achievable if you really want it.
39:59 a valve cup is missing. Ready to be scrapped again
Волшебным образом двигатель с водяным охлаждением превращается в двигатель с воздушным охлаждением. Уже на этапе разборки стало ясно , что это фейковое видео. Двигатель не разобрали даже - и так понятно, что он сгнил и проржавел окончательно.
Its not the same bike because when he cuts to the video of him assemblying it you can notice a three things 1. Paint is not the same 2. Engine is not "freshly" painted 3. The frame welds are gone like the frame was never broken
its a CBR 150cc .how it become 1000cc
What a mess!!.............you did an awesome job!
Que lastima como cortaste una moto nieva y lo unico asombroso es la combinacion para hacer la patina de oxido las cosas por dentro estan nuevecitas!!!
How does tires and plastic fairings rust? 😂 and the red rear shock look brand new?
I've always wanted a motorcycle racing car
Es correcto esa moto es posible 200 pero lo que si son exelentes mecánicos además aprendes observando los vídeos 👍👍👍👍👍
Pengerjaannya kurang detail, seharusnya mulai dr awal sampai sedetailnya. Jd sy kurang puas, kl mr jack itu baru detail sedetail detailnya sampai bagian yg terkecil.
Where is the part 2 ?
Ich bin 75 Jahre alt, und habe auch selbst repariert und restauriert, Junge, du hast Ahnung und dein Schweißwissen ist fenominal, trotzdem bekommst du kein Lob von mir, warum nicht, ganz einfach, schlampige Arbeit, schlecht gespachtelt, noch schlechter geschliffen und nicht nach gearbeitet, nicht grundiert, einfach überlackiert, was man so lackieren nennt, den Motor ohne Dichtungen zusammen gebaut. Nein ich hätte mich nicht getraut solche Arbeit abzuliefern, auch wenn ich jetzt einen Shit Storm ausgelöst habe, das Video ist keine Werbung für dich.
Be interesting to see it pass a mot 😂😂
Think you have the gloves on the wrong way the green bit gose on the parm off the hand not at the top
Parabéns cara ficou muito bom trabalho muito bem msm
This is not 1000 cc it's Honda CBR
Wow! Fairings can rust … amazing
Que alguien le enseñe a soldar a ese muchacho por favor
Never leave a Vietnamese meal in a junkyard. Then he thinks he's in heaven!
It's Cbr 150 i think....
1000, com um cilindro e um carburador tem que rir, rsrsrsrsrsrsrs !!!
Primera vez que veo un Honda 1000 de eso es un Honda 200 a partir de 250 es 2 cilindros y la 1000 es de 4 cilindros
im amazed it runs lmao
26:38 looks like the meteorite from joe dirt😅😂
Damn 1000cc with single cylinder 😂😂😂