✔ Tutorial how to BSI reset step by step on Citroen and Peugeot
BSI Problems and reset procedure.
Don't buy a new BSI (Body Systems Interface or Body Control Unit) for your Citroen or Peugeot until you have read this and tried a factory reset first. Very often the reset will solve a multitude of problems especially the ones that suddenly happened after you fitted a new battery to your car or the ones that just 'appeared' form nowhere!
- Economy mode active?
- Wipers stopped working?
- Central locking gone mad?
- Windows stopped working?
- Indicators and lights doing their own thing?
All of the above can be caused by a nutty BSI and often a reset is all it needs so try this....
Put the driver's window down, lift the bonnet and ensure all equipment is switched off (stereo, lights, wiper, etc)
Ensure all doors are closed and remove key from the ignition.
Wait for 3 minutes, disconnect the vehicle battery and wait 15 seconds.
Reconnect the vehicle battery, wait a further 10 seconds (do not open doors).
Switch on the side lights through the driver's window.
Switch on the ignition and check system's functionality.
Hold lock button on key down for 10 seconds.
Remove key open & close door test central locking system.
Start the engine and complete the system's check.
Failure to follow this procedure could result in incorrect operation of many BSI related items.
Tutorial how to BSI reset step by step on Citroen and Peugeot.
Tools needed:
rover.ebay.com/rover/1/710-53...
~-~~-~~~-~~-~
Please watch: "Tutorial How to P0325 Knock sensor replacement"
• How to P0325 Knock sen...
~-~~-~~~-~~-~
Amazing .. now at 75 years young I will need to view your video a few more times to get the hang of what to do. excellent video .just the right speed for Old thicko's like me .
Thanks very much 👍
And me👴👍
A big thank you from me for posting this video, my cruise control wouldn’t work properly on my Citroen dispatch and it was driving me crazy, I followed your instructions and now my cruise control is as good as new … thank you 👍👍
Great, thank you for the positive comment.
CONGRATULATIONS!!!!!!!! On my Citroen Xsara VTS the central locking works again. Several technicians, proposed various solutions. The final one was to replace the BSI and the ECU!!!!!!!!!!!!!! Thanks again
👍
This looks more like some dark magic ritual, but worth a try. Thanks for the video.
A few weeks ago, I asked if the BSI reset might cure my Citroen C3 fuel gauge showing 2 bars and Still 2 after putting in £20 of diesel and then it would count down till zero range. I did the reset and IT WORKED!!! Can't thank you enough. Peter
Great! 👍
Thanks very much! Peugeot 308 1.6 hdi (2013),had problems with radio, Bluetooth, park sensors and power sterring since my last general inspection. And this worked like a charm! Thank you
Great 👍
Your dealership obviously didn't do their job properly.
first class-just saved me a lot off cash-mechanic said big job at least £200-central locking stopped working from key fob but locked when key turned in door--------looked at your video-tried it out------central locking 100% working-thank you for posting
Thank you for watching, and I'm happy that fixed your car.
@@WhatTube hi man my car 508 /2013 petrol The problem Eco mode doesn't start engine only. Otherwise all work. Is this procedure helpful. thank you for all
Chevy you did not need BSI reset, your key fob just got unpaired from the car. The manual mentions this may happen and explains how to pair it. The pair procedure was part of this video - turn the ignition on and hold the lock button on your fob for 10s, which is why it fixed your issue.
You're a legend for posting this, it worked like a charm thank you very much!
Great! 👍
What worked? His car could start?
Worked perfectly. Thanks for the simple fool proof step by step video.
Thank you for the comment.
This was 2018, and it's still good!! Got a Peugeot 308 2015 1.2ltr Allure, one day it would not even turn over, much less start, worked out it was the battery, went and changed the battery, and saw BSI on it render the audio screen frozen, non-communicative, after about five seconds. Would mute, no button pressing, nothing, change the screen. Absolutely peed myself, wondering what it was I had to do, on m own. Got onto YT, searched and found this video, it seemed compatible, gave it a go, followed everything, and it worked a treat!! Thumbs up.
👍
I've just bought a 2015 Peugeot Boxer and info like this is very helpful knowledge thanks very good clear video... thanks
Peugeot Boxer is a Sevel Fiat product with a magnetti marelli BCM, not the PSA BSI, this procedure will do nothing to it.
This also works if you can’t lower your window, you can do it with 2 people. 1 outside who disconnects and connects the battery and 1 inside to do the light, ignition etcetera
Thanks for this worked on mine. Wish my engine looked as clean.
alberto ascari, I'm very happy that worked, thanks. And my engine is not that clean outside (but inside is very clean, check my other video where I changed the engine oil and you will see how clean was the oil). Thanks again 👍
@@WhatTube My wipers and lights turn on by themselves will restarting help?
Didn't really believe this but i had a fault with my Expert van, one rear indicator had no power getting to it. Carried out this and now works perfectly,thanks alot !
Your welcome 👍
How did you access your battery inside with all the doors closed? Did you just stay in the van?
Worked for citroen c3 that had problem with electrical devices on stearing wheel such as indicators lights and odemeter and fuel gauge. Spot on easy fix
Great! 👍
I just pulled the shunt fuse for a few seconds and it's fixed. Thanks
Great!
😂😂😂😂
Which fuse?
Thank you so much, just got my first car (Peugeot 2008) And then trunk wouldn't open on my second time driving, tried doing the BSI reset as recommended by you and it WORKED, thanked you so much!
Great 👍
Thanks it worked!!! You saved me a stressfull day
Thank you for watching.
This turn off economy mode?
@@zuikispuikis6039 - "Economy mode" automatically turn off the moment you start the engine. BTW "economy mode" is set to safe guard the battery. So, it turn off interior lights, radio, etc, etc! Just to mention the most obvious things the driver can see/hear. Really, can't be simpler than that... ;-)
Faaaaantastick!!! Thank You thank You, good man!! Two days I was looking for problem, couse I could not start my Partner '06 2.0hdi, and after this reset it's ALIVE again!! May the force be with You!!! 😂 TY for this video!!
You're welcome. Happy to help 👍
Thanks for the video tutorial. Hopefully it will solve the problem of my ac blower.
Excellent video ,seems a very unusual way to reprogram fob but worked a treat . Thank you very much for posting.
👍
It's seems to fix a fob you need a car that can start?
Thank you very much for this video. Followed the steps shown. Am absolutely delighted to find the door locks/unlocks again when I press the remote for my Peugeot 407. Thumbs up and God bless.
Great! Thank you very much.
I changed the radio of my xsara Picasso 2005 1.6 hdi and lost function on screen. This procedure restored all screen info. Thank you so much for this.
Great 👍
Thanks a lot ! This is indeed a realy helpful video ! 💪🙏
Thank you 👍
325 Comments on a very helpful video. Kinda cringe worthy that ONLY 5 of those reply's are rightfully thanking the poster for his contribution but the other 320 free loaders have treated him like a Free Peugeot Help Line with no mention of the video whatsoever. You people need to stop taking and start giving. The Comment section is where the content consumers can leave their thoughts about the video not bombard the content creator with your car problems when you can't be bothered googling them yourself. Props to the poster as he's gone above and beyond by answering a huge chunk of your personal car problems, no doubt costing him countless hours of his time. People are so self important these days 😡
Josh Brookes thank you very much.
My car has problems can you help! Lol 😂
Very useful. Used to do this to cure my C5. However, I was told to put the side lights on before reconnecting the battery as they would then absorb any voltage spikes which may be caused if the battery terminal doesn't make a clean contact.
I can see how unclean contact of a battery terminal may lead to voltage dips, but how could it casue voltage spikes?
@@YS_Production as the battery terminal is replaced, the circuits pick up the voltage. If the terminal makes a series of contacts as it slides down the post, the contact will 'make and break' giving dips and spikes which sometimes can be heard as crackles or even seen as sparks. Even if the spikes are less than battery voltage, the processor may be damaged. I was told too that if there is any induction in the cars circuitry, then a falling voltage would produce a back emf which could be larger than battery voltage. I am just going on advice and explanation I was given myself. It always worked for me though!
@@YS_Production.
Sidelight? Blinker, orange light on the side of the car? That is not what he is turning on in the video. He is turning on the original front lights?
Fantastico! Funziona! Spia resettata. Berlingo 1.4 purethc 2018. Wonderful! It works! Thanks a lot.
Thank you for the comment.
Thank you sir. Extremely helpful!!!!
👍
Thanks. To paraphrase Arthur C Clarke, "Any sufficiently complicated reset procedure is indistinguishable from voodoo. "
Sufficiently? This is braindead. I had a weak battery and now I probably have to pay a 1000 euros to get someone to fix this pos car that cost 2000, just because of a weak battery wth.
Hi, Great video - will do you know if it will work on a 2004 peugeot 206 cc the central locking has gone haywire!
Any news on your question?
Thanks for all the effort in making and sharing this tutorial. I managed to remove the esp/asr fault today. 2013/2014 Citroen Ds3 1.6 Vti Style. 👍🏻👌🏻🙏👏🏻👏🏻👏🏻👏🏻
Hi, great job 👍
Its come back or not
@@ayol4343 No. Still off. Very pleased
I fix that with a brake light cable, connector pull out from the socket, fix light cable and error solved
Thanks, worked for my P405
Great 👍
Would be nice to know why the BSI unit needed a reset in the first place but very good video all the same
Try to use logic next time. Probably because of malfunction of the BSI...
@@Alonz3 i get
I get that the BSI unit malfunctioned, what i should have said was, what was the fault or problem that caused it to require the reset Does not matter now, was 2 years ago
I've currently got a fault on my Peugeot 3008 where the BSI has malfunctioned and is causing the battery to drain completely overnight (something isn't being told to power off by the BSI itself). Peugeot want £700 to fix it so I'm going to try a reset of the BSI and see if it fixes the drain. Apparently the BSI can go wrong when you have a battery replacement or even a new key synced to the car!
Thank you for your "how to.." . If the driver door is on the left side, which door and door window will be opened ? the right passenger door or left driver door?
Hi, The driver side (left in your case)
@@WhatTube wie ist es mit keyless? 😢
You saved me! Thank you so much!!
👍
Great. Thanks a lot.
Dude, that's my car! 😂 I'm certain of it! It's now got 169k miles and still going
Nice 😄 good to know 👍
2 years ago on my C4 mk2, when the RAC connected jump leads and removed the red tag on the battery positive to make sure the leads were connected... This action of connecting jump leads and removing the positive caused the fault to sound the alarm everytime the doors were locked with the fob, I had to lock with the secret key to stop it from happening. I tried some of this, door closed, window down switch off disconnect battery. reconnect battery and then press lock button, there is no key ignition only a fob start button, but when I did that the alarm immediately sounded. This method did not work on the new C4. I had Citroen do it they said they uploaded a new BSI software to fix it. To clarify, removing the battery positive with the engine off, did not cause this fault. The fault only occurred when the RAC had charging cables attached but also at the same time disconnected the battery. I think this is what caused the fault.
It's always better to remove the negative terminal first. If the battery needs to be charged remove completely the battery and charge it. This method is working on the C4 as well but in your case the RAC mechanic damaged some components that's why it didn't worked for you.
I was hoping this would reset airbag light on my mk2 c4 grand spacetourer but now I'm not so optimistic
I had this same problem with my 2016 grand picasso, I sat in the car started the engine pressed the mirror button to close the mirrors as if locked , turned engine off and left the car and pressed the key fob and the system had reset not had a problem since .
Thanks for this video.. coming back to it every now and then as my center console display sometimes in my peugeot just keeps black after i start the engine. Or it stays on even if i stop the car. So every 6 month or so i am resetting it with your videos help xD works! 😂
👍😄
Thanks for this procedure. It worked perfectly for me last week. Superb.
Great 👍
Hi my windscreen wipers on my ds5 have stopped working after them being disconnected to replace front struts would this procedure help get them working again, thanks
Hi, thanks for the video! On my P5008 (2012, Petrol 1.6THP, Left Hand Drive, 7-seats) I have recently only the following lock/unlock problem and only during winter: while pressing the lock/unlock key button, the car seems to get the signal (because the led [P] on the parking lever turns on) but the locks don't lock/unlock. Everything else works fine and even lock/unlock problems disappear when weather gets warm. So, I assume my lock/unlock problem this is because of cold weather and humidity. Can you please advise which components or cable connections are prone to humidity or watertightness issues? Thank you in advance. Gregory
Hi, Did you try to replace the battery in the key fob?
@@WhatTube Yes, but with the same results.
Ok, you can start by cleaning the car battery's poles, then clean all the main cables attached to the chassis (negative). Then remove, check if there is bad connection or corrosion and reinstall all the fuses and reles.
@@WhatTube Ok, I will do. Besides, I would appreciate much if you could also advise where I should check for any exposed cables or cable connections, regarding cables routing from or to the BSI. Finally, please let me kindly remind you that the malfunction I have described above happens only when locking/unlocking the car and only during winter. Thanks again!
Hi Gregory, could you fix it? I have the same problem
Brilliant. Worked a treat and saved a fortune.
Great 👍
Great video! I have a Volvo so I don’t know why I’m watching but thanks for showing this. I will try this i if I ever have a Citroen or Peugeot that has these problems.
Thank you
Well don't be so pedant! If you have a Volvo, it's quite possible that you also have a Peugeot /Citroen engine in it! Particularly diesel, for which Volvo's have pretty much close to 100% of Peugeot/Citroen in it's guts! On petrol it's just loose components! ;-) Either case Independently of brands and models. 100% of modern cars have computers (ECU's) meaning that some might need a reset on occasion. Just like your computer at home! As an example a basic 3 cylinder Peugeot 107/Citroen C1/Toyota Aygo has some 7 or 8 modules. On a car that doesn't even have electric mirrors! Any run of the mill Peugeot from 15 years ago can have >20 separate modules ! With this said I have/had several Peugeots and Citroens, NEVER purposely reset them! Because, quite honestly, it's rarely needed. Many drivers tend to do it as a "cure all" solution! From low tire pressure, to old battery. LOL 😂
crpth1 i do have a PSA engine in it and I’m not stupid I do know that stuff so don’t need it explaining to me like I’m fucking retarded.
Great video ... my engine cuts when I am driving along ... I get all sorts of alarms come up on the dash .. then the engine completely stops .... I turn the ignition off ... wait 15 seconds, then it’s start back up straight away .. any ideas ??? Would be most great full....
Hi, have you done a diagnostic scan?
Did you solve this. My 308 is doing the same thing
Did you ever solve this. Mine is doing this now. Thanks
@@martinedwardfleet My 207 HDI as started doing this, dangerous. I'm just looking into getting Peugeot planet 2000 and give it a scan
Thanks for video. Problem I have is that the lock button on my key doesn't work (I just lock it manually). Is there any way I can perform the BSI reset without doing the "Hold lock button on key down for 10 seconds." bit? Thanks.
Yes, just skip that point.
@@WhatTube 👍 Thanks, will try that.
@@MrWibble Hi , did the bsi reset worked for you even you skip the holding key lock button step ?? Because for me its the same case i have no central loking at all neither from the key nor from the lock button
@Wipols Walid Didn't try in the end as someone I work with suggested this - 'Switch lights on & disconnect the battery & leave for a while (I left it for about an hour) to totally discharge the system, then reconnect'. That worked for the problems I was having (no speedo/odometer, random engine management & PS lights & horn operating by itself even when car was locked & I was no where near it!). I guess it's basically the same sort of thing as the BSI reset process in the video. Hope this helps. :)
@@MrWibble Thanks for the reply ,i understood that you followed the steps as in the video except you skip the holding lock key step , i wanna tell you also that i checked the bsi today ans it seems to be damaged and need to be replaced by another one also reprograming the new one too also get th key pin code from the damnaged bsi , i'll try this method ans escape the key step if it doesnt work i have to change the bsi or put a new lock system
So this really works :)? That's amazing. I didn't know you can disconnect battery on running engine
Hi, yes, this works, but you don't have to disconnect the battery terminal when the engine is running.
Thanks, worked for my Citroen Jumper
👍
There's another cause of non-start and ECO-MOD display. If you replace the Key Shell, you must also locate the key code chip in the old shell (a little black chip in the corner, easily missed) and move it to the new shell.
Peter D Morrison That is true, without the transponder chip the car will not start at all. :)
does it need to be re-soldered to the new chip?
No, the transponder chip does not need any connections, it can be easily removed with just the fingers, sometime can be dropped accidentally .
Thanks for the info, I changed the shell of my key today and not a hope would the car start, I didn't even notice the chip, it's starting now after reading this comment, thanks man
some times the chip is part of the door remote control an does not have a separate chip on the mrk3 type c5 @@WhatTube
When need this to do it?
Would this work on a 2015 2.2 Pg Boxer? I got a discharged battery a couple of times in the last few months and tried unsuccessfully to start the engine. Would this sort of voltage irregularity cause the problem?
Worked like a charm. Appreciate that!
Great! 👍
How do I know if the bsi is actually reset or not?
Interested
Hey guys! Im having issues with my pegueot 207 (2008) where the instrument panel/dash lights start flickering, sometimes doesnt turn on (headlights and stuff work fine). Anyone else had this issue and could this method be a possible fix? It usually happens after the car has been parked over a period of time.
Hi, it looks like the issue is the battery itself, next time try to start the engine with the clutch pedal down and all the electrical things off (lights, stereo, ac, ...)
I've a 2017 C4 1.6HDI. All needed to do, when the car was shut down and off, was disconnect the battery for a second and reconnect. 3 minutes to re-boot and my central locking, and key fob non recognition all sorted.
Thanks. I followed this hoping to fix an unexplained rear nearside light cluster failure, which is intermittent. It didn't work, but the key fob seems to be working better now!
👍
I actually then tried removing the connector and cleaned the pin contacts. It’s working fine now 👍🏽.
Had it on mine on both sides with the earth pin, which had overheated on the loom side of the connectors and became corroded as well, replaced them with new connectors and working fine now
I left the light on in my 2010 berlingo and now it beeps every 15 seconds even when the ignition is off. Everything still works. It's just so annoying. Any ideas?
Hi, Do you have the navigation system whit the display? If yes I think is that one.
Hi I have a strange problem with my 2007 207 1.4 s .. I park up and walk away from the car with my keys and then maybe 10 minutes later my car wipers are going and heads are on. Open the door and it stops. Any help or advice would be great thanks .
Hi, most probably you have a corroded BSI unit, you can try to remove and clean it with isopropyl alcohol.
Hi there Clair as a Peugeot technician I do know there is also a TSB bsi software download for that very problem. Get someone to check for water ingress first as per the whatube comment.
Hi I have the same kind of problem can you please tell me how you fixed it lplease Thanks Kennny
Thanx very much . It worked perfectly
Great! 👍
Great video. I have a 308 so have to disconnect positive as negative hidden. Should side lights be turned on 1st before reconnecting in this scenario as someone else suggested?
What is the reason to reset BSI?
Without going into too many details. Consider this the equivalent off resetting your PC... In fact it's exactly the same! ;-)
Hi Does this method removes messages From the computer: for example depollution system faulty. I replaced EGR and the error stayed. Peugeot 307 lift 1.6 hdi 90km
No it doesn't
I have the same damn fault with my 2008 308 1.6 petrol its running like a bag of shit and the engine management light is on then when driving flashes and goes into limp mode
is this guaranty BSI thing to work or do you have to do it a couple of times, also if the front window is broken by the BSI am I done for.
Great video. I have a 2007 C4 GP and both rear view mirror electronics don't work including the indicators in the mirror. Going to try this reset to see if it helps
Thanks
did it work?
@@alanlozano6535 Too expensive to repair for me so sold it on.
Oh man the driverseat is on the wrong side :)
Pimp Dumbel Hi, I live in UK and here all cars are like this :)
Walk to the otherside !
It is on the right side
side lights through the driver's window
John Timbs kindly tell me how to deactivate red stop light in peugeot expert 2017
Thanks for watching and for all the LIKES. Important: Please DO NOT disconnect the battery while the engine is running, follow the steps one by one. Thank you very much!
Excellent video. Please continue to post more videos. I have a question regarding disconnection of the battery for post 2016 Peugeot 308. According to the manual, it says before disconnecting the battery, the doors and windows should be closed and wait 2 minutes before disconnecting the battery. I guess this is to put the BSI to sleep. However, I have seen many instructions including this video to leave the windows open so that the side lights can be turned on. So I am not sure if the newer models BSI are detecting the state of windows open or closed position. Any thoughts? Thanks. P.S. The peugeot 308 manual for 2016 model can be found online.
L Emech thanks, You need to open only the drivers window, if you don't leave it open before disconnecting the battery you can't reset the BSI and you can have various electric problems. Even the older BSI can detect the windows but if you wait few minutes the BSI enter in "sleep mode" then you can disconnect the battery. I hope that is helpful. If you have more questions let me know. Thanks.
Thank you for your kind response. I guess what I am not clear with is: 1. What is the difference with closing the doors and windows and after connecting the battery, wait 3 minutes then open the door to reset the BSI versus, leave the windows open and turn on the lights to reset BSI. I thought as long as the door is open after connecting battery, the BSI will reset. Or should a higher current draw be needed, then open the door followed by turning on side lights. 2. Is it necessary to always do a BSI reset after disconnecting the old battery and replacing it with a new battery? Or, the BSI reset is carried out only on a need to basis like there are problems with BSI. Thanks again.
L Emech 1. If you close the doors and windows then reconnect the battery and wait 3 minutes, then you open the door, in this case you are waking up the BSI by multiple functions (doors lock/unlock, door light, interior light, dashboard operation, ...) If you open the windows and after reconnecting the battery you switch on the light, you are turning on the BSI with only one function, so th BSI can't be "confused" by multiple operations. 2. Is better to do it every time the battery is changed but is not essential.
WhatTube Excellent! It’s all clear now. Thank you very much.
Excellent video and information! Will work this in my '00 106 gti? Thanks!
I think your car doesn't have a BSI but just the immobiliser box, so it will not work for you. Thanks.
Hi thanks for the info my c2 has antitheft message everytime I get in car will this procedure work ? Also do you have to disconnect the negative side of the battery ? Because positive side is just a clip
Hi, Try to use a different car key. You can try this reset maybe it will fix the issue. And yes you can disconnect the positive pole of the battery if you want.
Wow - I did not expect this to work, but it did -> PEUGEOT 206+ 1.4 HDi
👍
Thanks. Good job
👍
I have a 2013 308 1.6hdi active nav i will be changing the battery soon and wondered should i turn sidelights on before or after reconnecting battery or does it matter. As i have to reconnect positive last negative is covered by battery cover.
Good video. Got couple questions a) Can you disconnect the battery at either the positive or negative terminal. My battery negative is hidden well inside the bonnect, can't reach it without taking out the whole battery. b) do you think this reset might be fix fault that flag up in the system when you initially start it up. I have had Eco activated, Engine needs repair, gearbox fault and parking brake fault all in space of a week when I start car initially
Hi thank you. a) yes you can disconnect the positive terminal. b) the Eco mode might get fixed, for the others you need to check for any faults stored in the ecu.
Thanks for this
Your welcome 👍
Thanks for the video, very informative. Do you think this will reset the adaptive for the auto transmission? I changed the fluid but had no way to reset the oil counter. Thanks
Hi, for the transmission oil, there isn't any need to reset the interval. There are only few cars that have one, and you can do it only with the diagnostic tool.
My 2012 508 SW doesn't have a factory reset option in the interface, so is this gonna do it? The GPS and radio started malfunctioning for a few years now and it's almost unusable now, so I am unsure if this will help, but I will try. The systems work sometimes, but not consistently, so it has to be some software issue, and a tiny cleanup should do the trick if the problem's trivial.
THANKYOU! My 2003 Peugeot wipers stopped working. It spent 2 weeks at the garage - they tried a whole bunch of things to fix it but gave up. I’ve just brought it home and tried this as a last resort and boom. Wipers are working again. Can’t believe it!!
Great 👍
Hi got a citroen ds4 where the automatic tilting mirrors when reversing have stopped working. Would this help?
Thank you I will give it a go
👍
I just watched your video , i am looking for a solution to solve my Comm 2000 issue . Last year i saw a video about dissembly the Comm 2000 because the lights were turning on all the time . I did that , cleaned all electrical contacts and it worked . 2 days ago the issue returned but now whatever i do lights just dont go off . Today i did the same like last year but it didnt worked . Comm 2000 its very expensive ! After watching your video ( 5 min ago ) i go try to reset bsi doing exacly like you did . I have a Citroën c5 2.0 hdi exclusive 2011 , you did that on a C5 so im very positive it will fix . So , i go now try and will be back with the result .
Hi and thanks, if it's not fixing the issue you have a malfunctioning parts that cause this issue.
@@WhatTube Yes , probably . Think This time i will have to spent some extra money with a specialist 😩😩😩 . Thanks , keep making videos like this one are very helpfull
Excellent video. My car won’t start at all so going to try this first as the garage said they can’t fix it. My problem is that the keyfob isn’t working properly so won’t be able to complete the process without the key fob functioning?
Hi, if the garage's person can't fix it then most probably this reset will not work. The reset will work if only the buttons on the keyfob are not working but if the key itself is not working then the reset will not be completed.
Good video... I have a Pug 508 RXH no sound from the infotainment system. Its also a hybrid with ectric motor for the back wheels ... will it correct my sterso system?
Thanks. Merci beaucoup. Grazie
👍
Hi and thank you for this tutorial but can you give us the reset procedure for 508 from 2012 with keyless ignition ? Thank you a lot !
Krystofer Savarin Hi, thanks for watching the video. The procedure should be same, for turning the ignition ON you have to press the START/STOP button once but release it quickly. All the other procedure should be same like the video. If you have more questions let me know. Thanks.
Same way, same car
Hi, brilliant video but before I perform what you done, would this fix problems with the ecu? There isn’t really any specific error codes for the ecu it just says that the ecu has a problem as it is cutting my power when the turbo kicks in. My cars a Peugeot 208 GTi 2015
The BSI it's like a second ECU so you can try it and see if it solve the issue.
Wow!! Excelente tengo una 3008 Gt line y no me funcionaba el acceso a manos libres y me indicaba que no detectaba la llave, y con esto quedó totalmente solucionado!! Muchas gracias por tu video eres un genio!! Y de paso sabrás cómo actualizar cartografía latinoamericana a este modelo ??
Thank you for the comment
Thank u sir itz perfect
👍
thank you!
👍
That's amazing video thanks for ❤
Thank you for the comment 👍
Hi, great video. I'm wondering if this would help me though. I have a 2007 Berlingo Multispace that I have had a couple of months now. However, the fuel pump went today and when it arriveBSI reset work for that? Eco Mode also comes up on display.
Hi, you have to replace or fix the fuel pump first, then you can do the BSI reset.
Bonne vidéo ! Merci pour ce partage !
You're welcome 👍
Thank u sir...itz per
Hi, great video! I've got a citeron c4 1.4 2008 and I wanted to ask will this reset work for a ABS light on my dashboard? I figured if I turn the light off and it comes back then I know there's a problem.
Hi, No it will not reset the ABS light.
Hello, this tutorial works for a peugeot 307 1.6 hdi s/w year 2007? Thank you
Hi, yes it does work on your car.
Top vid. I have a 2004 c2 will doing this reset the electric steering also?
Hi, doing this procedure you reset everything, but if there's a different issue, for example the electric motor that moves the steering wheel, you have to fix that one.
Hey got a question does this work for bad fuel level readout on the dashboard
Hi thanks for the vid, I have two questions: 1 ) Does this clear the learned adaptions of the ECU? I.e. can I use this to reset the adaptions after installing a new VVT and chain , without the need for a diagnostic tool ? 2 ) does this clear fault codes ? Many thanks
Hi 1) yes, this method will clear some of the adaptions learned but not all of them. If you replace just the timing chain usually there is no need to reset but for the VVT you need to use a diagnostic tool. 2) This method does not clear fault codes, in some cases the light may not show on the dashboard but the fault is still stored in the ecu.
@@WhatTube thank you!
Hi Thanks for the video Do you know if this would work on mark 1 C5 automatic lights do not come on would it fix that? Thanks
Hi, the best thing is to try and see if it can fix it. 👍
Buenas, sabes si serviría para este problema de la berlingo? El velocímetro a veces funciona y otras no, cuando no está funcionando , cuando quiere se pone bien el velocímetro y el motor tira más, y también a la inversa. Esta bien y cuando quiere se pone en 0 el motor tira mucho menos . Gracias
It sounds like a problem with the engine, not the speedometer?
Hi there ! I have a C5 x7 2008 and the wipers work whenever they feel like it ! Any thoughts!? I saw your video replacing the motors ! Could it be something else apart from the motors? Thank you
Hi, check the fuses and the wires, but most probably it's the motor itself.
Heyo! Not yet tested this as I am charging the battery atm, was wondering if there was other things than this to try out to get my alternator working again other than taking it out (Its a Berlingo 2011 1.6 HDI Diesel engine, utter pain to get to it) Want to explore all other options before I gotta get in hard and dirty :P Barely use it as I mostly just use my job car. Got other issues aswell so hoping its just the bsi being bratty. If ya got any ideas to try out I'd really appriciate it! ^_^
Hi, if the alternator doesn't recharge the battery it can be the alternator clutch pulley as well. Check all the fuses and relays, and all the wires on the system. Check if the bsi is corroded or faulty ( if it is, then normally you have more than one thing not working or working inappropriatly)