Homemade 200cc CHAINSAW With STAND For Cutting WOOD !?
2022 ж. 28 Қаз.
559 896 Рет қаралды
⚡⚡⚡T-shirts on sale soon⚡⚡⚡Follow this profile : / herosso_shop
.
My TikTok : / doctordsyoutube
My Instagram : / doctords_youtube
.
MAX Tools / Kožul :
www.kozul.hr/
.
Unior Tools: www.unior.com/
.
.
Photo equipment
-SONY A7III
-SONY 18-70
-SONY 18-200
-2x Nikon d3200
-Nikor 18-55
-DJI Ronin SC
-RODE
-RODE NT-USB
-GoPro 7 silver
.
Za poslovne upite: dadoskrbo16@gmail.com
For business inquiries : dadoskrbo16@gmail.com
Very dangerous design. You need to extend the control arm past the end of the chain or you'll end up chopped to bits. Don't lean over any where near the chain and put a kill switch on the end of the control arm
Think this ist really Dangerous by Design, the arm of the operator is to near to the chain. Another mistake is that the chain speed is to low, which can bei seen by the vibrations during sawing the wood. I would recommend everyone NOT to try this by yourself, the machine is highly dangerous.
Totally needs a guard for the end of the blade. I was expecting to see one built.
hello, the speed of the chain look to slow , no oil lubrification, bad position for the engine when you load the wood , cranshaft oil is over good level/angle , but good job :)
I think you should change the design as so you're not getting near the rotating chainsaw. If your clothes snag then you'll loose your arm!
Может рукоять просто сделать с задней стороны, чтобы рукоять не потерять.И такая пила будет тяжелой и трудной для заготовки дров на зиму.
sugestion its better put handle at back of the engine for safety rather your facing the chainsaw.
This cuts slower than a good chainsaw. BUT, now you don't have to shave your underarms. Well, maybe one. Agree on gearing -- way too slow. Even slower than the old gear saws. And maybe a valve on the oiler? Treadle control? And I know this is all in fun. My favorite caption: "Safety First!"
Great for cutting logs, arms,removing the odd elbow or 2. Not much in the way of health and safety......Please change but great concept but needs modifying.
Love the song in the background. Leaning on the everlasting arms. Song it in church growing up.
You just need to make a guard for that chain blade, the rest is perfect nice buddy.
Jedesmal wenn ich deine videos sehe denke ich es kann nichts dümmeres mehr kommen. Danke dass du mich immer aufs neue vom gegenteil übezeugst
Zu dumm um a Stihl zu starten....
@@christianhandwerker6863 😂😂 ne reperatur kähme unter 50€ aber man kann auch nen 200kubik motpr dranmachen. Kommt nur mir des so vor oder funktioniert des nicht soo wies der typ wollte😂
@@Pfoffagonder ....zu wenig Umdrehungen ....
@@christianhandwerker6863 gemau. Die 550xp dreht auf 14.000rpm hoch😂 so n 4takter normal nur 6-8😂😅
Sweet.A 'jackshaft' with a gear set to multiply the chain speed x5 will get your work done much quicker.Still,it's a good build as-is./Slatko. 'Pokretna osovina' sa zupčanikom podešenim za povećanje brzine lanca x5 će vaš posao obaviti puno brže. Ipak, dobra je izrada takva kakva jest.
The cutter should be placed in a balanced position so that when holding the handrail to cut it, it will not be heavy because the weight of the screw cutter will be heavy. Leaving it in the tensioned position by taking the spring wire to hold it when cutting will be lighter. .and the head of the wood when the saw is cut should also be left at 3/5 of the rack, the saw cuts off the wood, it will fall down by itself, we don't have to push it down from the cutting table.
After reading some of the comments I agree there needs to be some changes in the design to make it more safe .I also agree the chain speed needs to be nearly doubled .I think those issues addressed and this could work fairly well...The engine has about the same horsepower as a few of my larger sthil chainsaws but they have much higher rpm therefore high chainspeed so they cut smooth....I would double the chainspeed by gearing it different .I would also buy a racing kart camshaft that is designed for higher rpm....These little motors with mods such as cam and larger carb make almost twice the horsepower and can turn as much as 9k rpm .So my point is if this project has more fine timing and the safety issues addressed it really would be a good useable saw at much lower price than a sthil 660 or 661 .And could put out more horsepower but I don't think it needs alot of horsepower to cut the size logs that fit in the cradle....I do thing it's an interesting ideal and I've often wondered how one of these predator engines would work as some type of chainsaw....Stay safe and keep working on it and show us another video after your done
right on ,,chainspeed needs to be at least double if not even more,,that fourstroker revs maybe 3000 rpm while a chainsaw revs 10 000 rpm and a extension vith a 90 degree bend on it for the handlebar is a solution maybe to the crazy dangerus stick that he is using now, and the oiler needs to get in to the bar under the chain so a small hole and a groove behind the oilerhole in the bar and a nipple on the backside with a ballvalve should be a better way to lubricate the bar and chain
Keep an eye on that crankcase oil. You might want to add a little extra to compensate for operating the engine at an incline. If you ever do a redesign, consider a fixed engine position with the jackshaft to be the pivot point for the chainsaw bar.
triple or quadruple the engine speed(most saws run at 14krpm). a simple band break around the outside of the clutch would make it ton safer, make it so it disengages when you pull it down. also i think i would have made the blade only piviot. i don't really see the practicality of this, you just end up lifting heavier wood. if it were built into a log splitter i could see it. sorry to sound so negative, good video though.
I would not feel safe using that handle. I would bend it at a 45 degree angle towards the back and that way it won’t be facing you
Look for photos of chainsaw injury, never get that close to a running chainsaw. Good video terrible design.
My concerns is angle of engine with overhead valves oil getting in head and carb.also I would guard the chain.really don't sea how engine os running with carb tilted back so far.
Голодание маслом у двигателя не будет? Наклон большой.... Маслозаборник захватывает масло всегда?
U are a bit near that chain
i would put a guard on top of the blade!
Ok idea, but chain saw chains you have to constantly sharpen. A 24 inch buzz saw blade on an inch and 3/8 arbor would work much better with that motor and minimal blade sharpening. Cool the blade with water if you have to. Much safer way. I use one run off my tractor pto.
You have crazy amazing skills. That is absolutely amazing. Bro you should patent some of you inventions. You make millions!!! Another awesome video my dude. Keep up the amazing work
Dangerous
For christ sake put a guard over the blade before you loose your arm or worse
Workins but no safety !!!!
12:39 i was hoping the go kart seat was going on for lazy days
Do you still have all your limbs? good time to design a safety guard around the saw now you still able.
arm amputator 3000
That was one of the best inventions you ever ha is always nice to watch your videos. Kind regards buddy.
Das wird wohl nicht so gut funktionieren, wenn man bedenkt, dass der Motor nur bis 3000 U dreht und die Kettensäge bis 13000.
Odlično👍👍👍👍
I think its not good for this type of engine to work on this angle. The piston cant be oiled properly.
You do great work but this very dangerous. If that chain comes off watch out. Make a few modifications for your safety. You are very skillful and will come up with many more ideas for future projects.
The handle is a safety hazard. Design could have been better
Ovako napravljeno, možeš vrlo lako da ostaneš, ne daj bože, bez ruke. Mač je trebao biti okrenut "od tebe" sistemom poluga i pokriven- zaštićen jer ovako je mnogo NESIGURAN! 😉
Odlična ideja i posao,ali napravi zaštitu za lanac i polugu/ručku prečvrsti bliže da ti bude lakše upravljati🙂👌
Would it be easer spend 12.oo$ on carb kit doctor hardway????¿?
Pazi na svoje ruke da ne ostaneš bez njih. Sretno.
A very dangerous helper!
Эти моторы нельзя так сильно наклонять,а если его оставить так цилиндром вниз,то масло стечет в камеру сгорания.
that thing is super un safe no way to stop it with that clutch standing on the wrong side of the bar
Doctor DS logic: this thing stopped working, LET'S MAKE IT FKING 200cc
C'est un peu dangereux la lame passe à côté du bras. Sinon très bonne idée 💡
Samo sam čekao da vidim kako ćeš riješiti podmazivanje lanca 🤣🤣
Now you need a log splitter 😅😅👌👍
13:27 you almost destroyed your elbow.
it seem like too dangerous when you pull it from that side… the chain saw can accidentally touch any part of your hand or body, why don’t you make it push from engine site?
Really really cool 🤩👍
Bravo i hvala ti veliko prijatelju za sve video klipove koje objavljuješ.Prva liga,veruj mi...👍👍👍👍...
thats still really cool. atlhough u shud b on the otherside of the saw pushing not pulling. just an opinion.
Nice design you can increase the speed a bit by playing with sprocket ratio and change the way you are positioned to pull on the handle you are to near of the chain blade and too young to be injured :)
Sorry aber nach wie vielen Amputation hat er sein Holz geschnitten. Idee ist gut, nur in der Umsetzung doch arg Gesundheitsgefährdent.
great work !
dobra ideja ,motor bi tebao biti fiksiran na ravno zbog podmazivanja samo mac bi trebalo da se moze pomerati ,,bolja varijanta bi bila sa listom cirkulara ,lp
I would have just adjusted the Carburettor!
Good boss doctor 👍👌
Mean it’s time to buy a new saw😂
you killed me with "subscribe" and "like" reminder, every time i think i get a notification on my phone 😂
😅😅😅
Should have just fixed the chainsaw, yearly maintenance will keep those saws running for years..
I have to maintenance my ever other couple’s years to keep my running
I run premium gas though in mine
Super videi ❤️🔥👍💪,velika podrška, probaj na staru biciklu il nesto drugo montirati da pogoni motor od motorne pile 2kw
Odlična ideja svaka čast
Možda je preveliki ugao naginjanja za ovaj motor zbog podmazivanje,bilo bi bolje da je neki 2t motor zbog toga.
Odličan stroj samo što bi popravio ručku i štitnik za lanac bi metnuo odozgora
Napravi jos cjepac neki i imas full setup Samo nekako mi se cini da nema dovoljno obrtaja ,kao da sporo sijece Pozz
Good ii boss Doctor DS 💪💪👍👍😊😊✅✅
Besmisleno i nepraktično!
Hahahaha
koliko je vremena i para utrosio na ovu masinu mogo je napreviti magarca i brze bi rezao drva
this thing is the exact reason someone invented the fast, portable maneuverable chainsaw.
something feels like it doesn't quite turn out as planned.
,, Safety first " Yeah...but the chain run immediately, and never stop. Slow, heavy as f..k and not safe at all. "Good job"...
its nice but it doesnt look safe at all you almost hit your arm doing it , you can modify it a bet to be safer
Opala i tokarski si nabavija , , Uvjek si ima super ideje i pravio svašta al kroz godine si postao opušteniji i po malo ima zezancije i puno je zabavnije gledati vide❤️👍💪, , , , , da tako nekad dok upališ motorku već se umoriš 😂 , a gdje je najbolje gledat za dijelove za kartinge jeftino a dobro ,rabljeni ili novi djelovi ?
Karting svaštara, grupa na fejsu 🤗
@@DShomemade hvala
Good job what you did
Sieht gud aus, awwa das Ding geht jo wohl ken Schlach
Benim tek hayalim bir traktör
Amazing idea, but you should talk in your videos
this is exactly cuz of my travel to hospital with a bag in my hand what carries my other hand. Care pls.
please make a video restoring your old chainsaw(
Ottimo risultato lavoro eccellente
Jesi li ti jos davno imao strug posto ga dosad nisam vidjao
To je od tokara baš 😅
une protection de chaîne serait la bienvenue...
The approach to the product is solid. However, I believe that it is better to split 1 meter long logs firstly than to cut it to the size of the boiler, and then split each one again and again. Sawing logs is much easier and faster than splitting them. So, I advise you to first make a 1m splitter. I saw this approach in American blogger's videos . The Shepach company also makes 1010 mm log splitters for the same purposes.
The thing is Us Americans do not cut meter long logs. We buck out the wood to the size that we need which is between 16 inches and 2 foot. Then we split it all. I can process so much fire wood its not funny. I once bucked and split 5 cords in around 6 hours. I go to the river with my trailer and large side dump truck and have the farmer load me dead trees from 12 inches to close to 3 foot. Stopped doing the really big stuff and stuck with the 12 to 18 inch logs and get home and buck off the entire trailer using a cant and wedges when needed and while more than half of them land on the ground. I then split them in half then I will cut off the ends for some small bits and then split the log in to squares or rectangles. No wedges. I keep about 6x6 in the largest size. As this stacked quite well in my old stove.
Fora je, ali bezveze, opasno, lanac se vrti, kad das gas vrti se presporo, bas bas bezveze, ali ajde možeš i ti jednom totalnu glupost napravit, necemo odmah za zlo uzet😂😂 Popravi tu Stihlovku o mani se ćorava posla😂😂🍻
Šteta bagrem otišao u drva a sve dobri stubovi mogli biti😂
La idea es buena pero lo veo muy peligroso. Le falta un protector o sino desviaría la barra accionadora hacia un lado para no estar enfrente de la espada de corte. Un motor 4t? Pocas revoluciones. Creo que funcionaria mejor con uno 2t.
Ятак чут без руки неостался ветер подул ирукав зачепило вены на руку порезало
good job
thats going to give me nightmares i still like it awesome idea
Az àm a szuper illesztés!😂
where are you buying that motors in croatia
Great invention ! but why not use the original small engine? 👍🤔
bad idea since the engine is governured to 3600 rpm and the averagr chainsaw runs at the 12k rpms at full throttle therefore the chain doesnt speed fast enought to cut efficiently. What I would have done is bolt on chainsaw instead of the 200/212 cc engine and run it this was. otherwise great project. poz iz 🇸🇮
Super !!
I can ask for a name or a link to the apron. well done
4 stoke engine , not so good for chainsaw . Make it electrik
Looks like it needs a chain brake when the engine sits all the way back. What a great update video that would be.
Are u always using the same motor? otherwise awesome video as usual!
Good job
Nice but it's not good for engine
Sto pre napravi da motor stoji ravno a da se osovina gde je testera pomera jer u tom položaju motor ce da crkne jako brzo.... Inače video mi se svideo i dao si mi ideju jer sam cirkular prodao :)
Молодец как всегда🤟😁
put a gas pedal right of tire on engine side and put your lifter under the exhuast side too
Nekem tetszik👍👍 én örülnék ha ijet tudnék készìteni