Making Electric-hydraulic Tipper Trailer
I used a 12v hydraulic power supply that comes from a tail lift from a small van, The power supply has a built-in section divider, which makes it easy to install. To control the power supply I used a relay and a 12v winch pilot and receiver, and a 12v 20ah gel battery.
The hydraulic trailer can be attached to any vehicle, mower tractor, quad and car. Dump trailer the maximum weight it lifts is about 400 kg, limited by the strength of the wheels, if not for the wheels, it would be possible to easily transport and unload larger loads
Start supporting this channel and you will get these bonuses:
/ @workshopfromscratch
Tools:
Drill amzn.to/43dE6hO
Angle Grinder amzn.to/4a70xry
Other tools amzn.to/3IAQE9N
Camera:
Drone - amzn.to/4a5TvTP
Camera - LUMIX GH5M2 amzn.to/3UR6Niw
LUMIX G VARIO LENS amzn.to/49IfVdq
Camera - LUMIX G85 4K amzn.to/4a4deTY
GoPro Hero10 amzn.to/3uThjvm
Love the "pallet width" feature, very clever. Fantastic construction, I hope it helps a lot!
Thank you 😁
Bro! I'm mesmerized
Couple ideas to improve -- Build a hanger on the front face to hold the tailgate when it is not installed. And Install chains on the tailgate so you can limit the opening and control the spreading of product, like a dump truck does, Excellent video! Thank you for sharing!
Another awesome build! I never get tired of watching your skills and workmanship! Thank you very much for sharing!!!
Thank you 😁
Exceptional fabrication. I see you have bunches of high-end tooling machinery, but you obviously also have the knowledge to operate them. Best work I have seen in a long time!
What a superb design, followed by excellent construction technique. I have a trailer, but if I needed to build one, this is what I would use as a model.
Throughly enjoyed watching you work. Great skills & equipment!
That is a very nice design. One thing I would suggest is to cover the pump and battery with a solar panel which will protect them from the weather and keep the battery topped up without having to think about it. You might also be able to find an old tool box to mount them in which could also be a place for the remote control. I'm thinking of those tool boxes which would be deep enough, but then have a removable tray to cover the battery/motor and it could hold other small stuff.
This is a good idea! Every spot on my property that gets a mower, tractor, atv, etc parked in has a solar powered battery tender connection. That and flat tires are such a pain in my ass that I mounted a 12v battery and air compressor to a dolly... Has jumper cables just in case after one of the battery tender wires oxidized and that battery was dead even after being on a damn charger. Also has a shelf for a little 79cc 2 stroke harbor freight 700w generator but I haven't needed that for anything yet. I have grid power available in most spots but why have the constant drain when solar is sufficient.
In addition to the above modifications, I suggest adding a second set of tailgate connections to the front of the trailer so when you take the tailgate off the back, you can hang it on the front face of the trailer so you don't lose it, forget it and when you've offloaded whatever you took the gate off for, you can immediately put it back on the rear so you can then load more lose material (gravel, sand etc.) without having to go all they way back to wherever you left the gate...
I was rebulding a trailer last week and i sure wish i had access to the great workshop and tools you have there, you also have all the gear and great ideas, great workmanship
Super. I would change one thing and that is when the line comes in at the ram on the top. Put a hard line down to the pivot point this way the line only needs to move a small amount and the flex would be limited. Other than that a super build! Love it.
Was absolutely mesmerised from beginning to end. Quality I can only dream of. Hats off to you sir.
Thank you 😁
I'm a cabinetmaker of 35 years, shop full of tools, but the wrong medium.......enjoyed watching!
I have to say I quite enjoyed the drive to dump the cuttings while mowing but this makes dumping the cuttings more enjoyable! Please make a shute from the mower to the trailer for grass cuttings
That's a really nice handy little trailer. Thank you for taking time to film, build, edit and post this video.
Thank you 😁
@@WorkshopFromScratch you are welcome
Very nice job, enjoyed watching the build
Your skill is extraordinary your gifting from the creator of all things, such a pleasure to watch you work, sometimes I watch you for 5 or 6 hours and I'm still amazed at your skill. Keep it up sir, we enjoy watching you work!!!!!!!!!!!!!!!
ALL That WORK,and NO SUSPENSION;= PRIMITIVE PERFECTION.
Fantastic work, dude! 😃 The mechanism is brilliant! Well done!!! Stay safe there with your family! 🖖😊
Thank you 😁
Your workmanship is excellent and insightful And your video editing is getting even better.
Thank you 😁
Some outstanding metal work with some great tools to do so. Its always so much better to create something rather than to buy it.
You sir are a master fabricator!!👍
Great video. I hope the fittings on the hydraulic ram don't get knocked off - as they seem to be the lowest part of the lift mechanism - maybe some small skid plates to protect them would protect them. Stay safe out there.
Thank you 😁 There is more clearance between the mount and the ground than it looks in the video 😁
Great build and craftsmanship. Now I'm guessing the location of the ram is due to the length of its stroke and a possible need to tip it straight up, but if positioned so that the ram is closer to the front it would allow for heavier loads to be dumped, while simultaneously reducing the power needed to raise and lower the tipper save your battery and pump. But in the end it works and for diy that's all that matters. Thumbs up from me.
If my scrap pile was like yours I'd call it a gold mine.
Muito bom seus vídeos 👏👏👏👏 parabéns 🇧🇷🇧🇷
Excellent work, next project turn the lawn mower into a small front end loader🤣 👍👍👍 . Thank you for sharing. Take care of yourself, be safe 🇨🇦
Thank you 😁 But with this front loader you gave me a good idea - Thank you 😁
You're such an artist! Please keep making videos
Thank you 😁
Too nice , I think the kids will enjoy working while you watch them loading it with spades. I think you could have just lifted it off the hitch and tip it out lol , it's so small , sure the kiddies will enjoy their new toy. Very beautiful but you should make a bigger one for the big boys toys. Sure it's going to come in very handy in the paddock. I would really thinking of upgrading the axles though.
You sir are talented!
Nice build. I'd recommend a charge circuit for the battery otherwise it will just discharge as you use it. Maybe a solar charger or just recharge it after each use.
Thank you 😁 First I have to fix the charging in the mower troctor 😂
Excellent workmanship and a very good trailer. But a safety warning: this needs a swivel hitch to prevent the towing vehicle from turning over if the tipper trailer fell over sideways. It's an easy bolt-on upgrade. Also requires a fuse or circuit breaker on the battery connection.
Sounds excessive. Just don't tow or dumb on uneven grouf
Clearly you don't know what you are talking about. Even commercially built dump trailers don't have a swivel hitch. Why, because it's a weak point. That trailer isn't big enough and doesn't raise high enough to worry about tipping.
lol I'd be shocked if this trailer was capable of turning over a 4 wheeler or golfcart. how big do you think this trailer is? lol
My old man had a tractor tipper go over once at 30’ high. This is sound advice. Possibly not as much of a worry as his
LOL the design exceeds it's intended use .
You should install a tailgate release reachable from the drivers seat. Again, very nice construction as always.
Thank you 😁
That will come extremely handy in my garden. Well done. Very nice handy project. 👍👍👍👍👍
Thank you 😁
A master of fabrication. Beautiful. Thanks.
Nice trailer, well done!
Przydatny sprzęt w małym gospodarstwie, dobra robota 😎
Dziękuje 😁
Well, that project didn't take very long to build, but I would have painted it green. 😀 Handy little trailer... well done! Appears you have a bit of "scratch" invested in the workshop tools.
Thank you 😁 Troktorek mower is red that's why I painted it a similar color 😁 I try to save and buy tools all the time they are not always good quality tools but the most important thing is that they do their job :)
@@WorkshopFromScratch No need to justify the color you chose... I was just joking with you. I'm jealous of your tools. Cheers!
Super estetycznie Ci to wyszło. Tak trzymaj!
Dziękuje 😁
Excellent workmanship and an excellent result. Well done.
Thank you 😁
Nice work. Thanks for sharing. 👍👍👍
Piękna robota jak zawsze.
Dziękuje 😁
I'm like a kid again with some grown boy toys lol 😆 saving this vid. I'm gonna make one now.
Love the simplicity you keep in your builds. Hinges need some second thought.
Thank you 😁
Love the whole build. It's genius!. I would like to know more to where I can find that exact hydraulic pump and cylinder. I can't find it anywhere
Awesome design & assembly 👍🏼
Thank you 😁
Looks great. Very nice job! 👍
Thank you 😁
Jak zawsze super robota..👍👍👍
Dziękuje 😁
Nice workshop 👍
I’m impressed once again great work 👍🏾👍🏾
Thank you 😁
Great job. You have made such a beefy wagon. The only thing I would do differently is a better beefier tailgate latch system. The one you have does not match the rest of the wagon for strength. You have mad skills.
That's very cool, one day you'll make a 4x4 small Traktor just for the farming tools ... very nice job 👏
Yes, a small tractor is in the plans but I don't know if I will be able to build a 4x4, but maybe 😁 Thank you 😁
@Workshop From Scratch - tray to use hidráulica traction 2 wheels permanently on traditional gearbox, and 2 wheels with hidráulic traction. More controllable very simple to use and fewer parts and has independent traction and steering on demand. just an idea never seen I think, extreme hybrid 4X4 ... good job my friend
That will come in very handy. Good job 👍
Thank you 😁
Super robota pełen szacunek 😁😁😁😱 ja za swoją biorę się od 2 lat i wsiąść się nie mogę ha a może masz jakiś projekt na ta która zrobiłeś 😁😁tylko ja jeszcze muszę dorobić zabudowę z drobnej siatki żeby z tylnego wyrzutu kosiarki odrazy trawę łapać 😁
I am impressed, want to come down to Poland and buy it :D
Very nice trailer build, thank you.
Thank you 😁
Outstanding build, excellent job..
Thank you 😁
Nice build. With all the great tools its no problem making good stuff :-)
Awesome dump cart.
Świetnie wyszło!
This guy is a professional Fitter and Turner
No, I'm a self-taught amateur 😁
Your shop is so cool and never judge a book by its cover I guess
Nice work!
Pretty cool 😎👍😊 I wish you were my neighbor👍
i don't know why but i rather do it with external power source. make like trailer socket. because charging battery... im to lazy :D over all great job and amazing project... looking for your future builds
Spectacular job!
Thank you 😁
Niezła robota, właśnie sam szukam mechanizmu wywrotu do mojej przyczepki. Mógłbyś podpowiedzieć gdzie kupiłeś ten silownik i pompę elektryczno-hydrauliczną???
This was amazing to watch you build
Приветствую ,спасибо за хорошую идею
Belo projeto gostei parabens
Great Job 👍👍👍
Nice job!!
I love watching your videos your a very talented man
Thank you 😁
Maestria unica amico. Da manuale, peccato che per me è irraggiungibile fare quello che hai fatto. Ma come lezione per apprendimento è veramente unica. Grazie
O widzę nowa przecinarka taśmowa 😀👍
Tak, zagościła też nowa, ale stare też używam :)
Excellent craftsmanship 👍
Really nice build. You should sell the plans.
Nicely done.
Excellent job my friend congratulations 👏👏👏👏👏
Thank you 😁
Bardzo pomysłowe muszę powiedzieć że masz łeb na karku super łapka w górę 👍
Dziękuje 😁
This is just great.... can you write me how much milimeters has that piston woring lenght??? Distance between start and end position??? thanks
*Excellent!* I couldn't give this a "thumbs up" fast enough. Question regarding the sides: is there a specific reason, or advantage for the having angles vs straight sides? Is it to strengthen the box, or does it dump wet material easier without clogging? I also liked the latches you used-they're very similar to those on my trailer. [I think I shared a link with you at one point in the past on a previous build]. Anyway, great job-as always. *God bless.*
Thank you 😁 As for the slanted sides, it's mainly about larger capacity, thus not increasing the dimensions and wheelbase in the trailer, if I was making a larger trailer, I would use ordinary straight sides :)
I think the widening sides also act as fenders if making a larger, road worthy version.
You just simply amaze me!😃👍👍
Thanks 😁
Thanks 😂 know i know what Im gonna build My dad want that actually thanks for the idea also 🙌❤️ big fan u have made me do so many stuff
Thank you, i glad find my videos useful 😁
Congratulations sir for new cutting machine 😍😍🔥🔥 love from India ❤️❤️
Super travail 👍 une belle application
Merci 😁
Шикарно!👍
Spectacular ..mini truck i guess..⚘👍
You are an ARTIST!
Very good work. That must have costed a lot metal prices are crazy
O panie kolego, zajebiste !
It's nice to have a 100,000.00 machine shop at your house.
in the places where the tie rod was screwed, it was worth strengthening the holes and putting the bosses inside, in fact, almost the entire load falls on these two bolts, and over time they will bend the profile pipe ... it would also be nice to strengthen the welding points of the hydraulic cylinder mount and the hinged mount of the body ...
It is a trailer which, due to its dimensions, will not carry loads greater than 300,400 kg, so there is still an excess of material that I used
Very nice dumper!
Thank you 😁
super cool project !
Thank you 😁
Excellent work!!
Все красиво и замечательно! Но есть один недостаток! Ось прицепа нужно было сместить от середины прицепа хотя бы на 10-15 см!назад....А так при разгрузке он будет поднимать " тягач")....!
Always ALWAYS connect positive cable first - - then ground/earth cable last
you should add a section of chain on each side of the gate with a notch on the gate to allow you to limit the width of the opening so you can spread material rather than just dumping the entire load in one place.
big like. kool ideea.
Great job!!!👍
Thank you 😁
Smart work, so creative
Thank you 😁