How to Solder Wires Together (Best tips and tricks)
Learn How to Solder Correctly. In this video I show you the tools, tips, tricks, and techniques to properly solder, from what type of solder and flux you should use to how to splice the wires together for a strong soldered joint. I show you how to strip the wires, add heat shrink, splice the wires, solder, and melt the heat shrink to make a perfect soldered connection!
Tools:
Solder: amzn.to/2cfjNcv
Rosin Flux: amzn.to/2bVPzMB
Soldering Gun: amzn.to/2UI618D
Soldering Iron: amzn.to/2c0cRiX
Wire Strippers: amzn.to/2cDPvyk
Automatic Strippers: amzn.to/2c0cV27
Silicone Paste: amzn.to/2cEMikT
Helping Hands: amzn.to/2bVQL2E
Heat Shrink Kit: amzn.to/2cr3NmA
Butane Torch Tip: amzn.to/2c1QPzg
Heat Gun: amzn.to/2Six0pB
Project Night Light: • Custom LED Light Bar B...
How to Build a Police Car: • How to Turn a Regular ...
How to Buy a used car: • How to Inspect a Used ...
Drift Car Build: • Help me Pick My Drift Car
Become a ChrisFix Subscriber→ kzhead.info_c...
Instagram→ / chrisfixit
Facebook→ / chrisfix8
Website → www.ChrisFixed.com
My Channel Home Page → / chrisfix
*If the video was helpful, remember to give it a "thumbs up" and consider subscribing. New videos every Thursday*
Disclaimer:
Due to factors beyond the control of ChrisFix, I cannot guarantee against improper use or unauthorized modifications of this information. ChrisFix assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. ChrisFix recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of ChrisFix, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not ChrisFix.
It's not just a soldering tutorial; it's a lesson in effective, clear, precise and complete communication. Thank you
Thanks a lot!
for real
@ChrisFix Best DIY channel on KZhead!!!
YESSSS!!!!!!!! Its an art to be concise and succinct, while also thoroughly covering the body of knowledge. Some people talk too much, and some people talk too little, leaving unanswered questions. In a world of having many irons in the fire, and I just need someone to tell me how to do this in under 15 minutes, this video was worth ALL 12 minutes.
Sodder :D
6 years later and this is still the best tutorial ive seen. Not repetitive, goes over common mistakes, and overall helpful. Now i just need you to make a welding one
what type of welding do you need help with?
All of it I need point a to point z
That was the most informative, direct, sensible, comprehensive, focused, and skilled crash course on soldering I’ve ever seen! He doesn’t waste time, he gets to the point, but also explains WHY you need to follow the steps. Excellent video!
The perfect comment. Lol, DIRECT, SENSIBLE, COMPREHENSIVE, FOCUSED, WHY AND MAINLY, HE GETS TO THE POINT. I hate the reviews where it takes forever to even get to the instructions.
SIMP
Totally! I agree 100%
I got the very best education in soldering from the Navy and I can usually find something snarky to say about almost every YT "how to" video on the topic. Except this one. You hit everything I would have said, and every time I thought of a tip to add (adding silicone, moving heat shrink down from the solder zone, etc.) you mentioned it. Very well done. I'm sending anyone who asks about soldering to this video.
I'm glad to see this is how the pros do it too, thanks!
Awesome!!
Hi Chris! I hope this comment doesn't get buried. I have a few tips in addition to what you showed: - For one, with the lineman's splice it actually helps a lot if you give the wires a pull, the splice will get tight like a knot. Properly done, a lineman's splice that is pulled tight can actually make a good connection without solder, just heatshrink to keep it in place. - I usually just cut any strands that are sticking out with flush cutters rather than trying to wrap them around as that can be painful sometimes. - If it's a situation where the wire is experiencing strain--bending, vibration, etc--you want to avoid having too much length of solid solder, because solder is quite brittle. If you did the lineman's splice properly and pulled it tight like I mentioned, you should only need a small blob of solder on either end of the splice. - Using 63/37 lead solder instead of 60/40 is a bit more foolproof, as with 60/40 you have to make sure the joint stays still as it cools. With 63/37 it's less of a concern - Silver-bearing leaded solder is mechanically stronger than regular leaded solder, and just as good in pretty much every other respect except cost. If you're not going to need a lot, and the price won't break the bank, silver solder is great for any situation where the solder joint cracking would be very bad. - I generally recommend people *don't* buy solder from hardware stores, as it's usually only mediocre quality and almost always very thick solder wire. Generally the thinner the solder wire the better. The thicker it is the easier it is to add too much. - you don't want to heat wires too long or it will start to melt the wire insulation - you can actually buy heat shrink tubing that shrinks 3:1 instead of 2:1 which can be helpful when you're soldering together wire of two different sizes, or when you can't get an exact size match.
I agree with all of this.
Great addition to the video. I like the way you don't try to diminish the great tutorial. This is a great beginners tutorial and it is done perfectly. Granted, there are other techniques for more critical situations. Thanks for the information!
Dope !!
This was also helpful
I would also add to clean off the rosin with isopropyl alchohol as it is corrosive to the metals over time
Aaahhh, it feels so good to watch a YT tutorial that is well filmed, well edited, stresses safety, and made by someone who knows what they are doing. Just found your channel and immediately subbed. Thanks for sharing your knowledge. ❤️
Thanks!
Agreed
I"m a year late to your insightful comment, but I've never really watched YT until Covid struck. I've watched mainly car repair and alot of these younger YT guys really take chances with flammable liquids, compressed springs, cracked frames. I get that it makes for good clicks to operate vehicles that are not safe for the driver to be operating in the vicinity of other drivers, but it's gott damn dangerous and selfish. I'm glad to see someone with a healthy fan base teach safety infused DIY.. Subscribed...
Well said
2 years ago you wrote this comment
Been soldering (when I need to) for 30 odd years. Still learned stuff from this vid, thanks ChrisFix, you're a legend!
I'm glad you still got to learn something from the video! Thanks a lot!
Hey, building a lightsaber from scratch, and wasn't sure how to solder. So grateful for people like you who share their skills with others. Thanks again!
That's a cool project! Thanks a lot!
⁷⁶
As someone with extensive soldering experience I approve and appreciate the work put into this
You have extensive soldering experience and approve of him not cleaning the flux after soldering the wire then heat shrinking it? Lol
@@hyunwhyte1338 no need to get angry, this guy is no longer among us... :'-(
@@Ev-wj3lm what do you mean?
@@JARMotors He passed away 2018. I think bike accident
@@moya9450 HE DIDNT NOT YOU DICKHEADS
Bro... So thorough. No 2nd guessing, no corny music and no childish punny jokes. Straight forward and educational. Subscribed ✌
Half his video is bullshit he clearly put it to get over 10 min to minimize it. If you actually cut to the part where he shows u how to do it less than 3 min
This is as thorough and detailed as humanly possible. Thank you
Honestly one of the best instructional videos I have seen on KZhead. Very organized. Straight to the point. Great camera detail. Thank you
Been soldering for over 30 years, yet I'm here, watching a soldering video. :-)
Lasse Huhtala same 👍
That is the right attitude. Never stop learning!
That's funny. I've been soldering for 50 years and here I am watching a soldering video. I will say though, I never thought of making my own solder gun tips, so here I am still learning.
Finally it's Ed any tips for very tiny fragile wires? They come pre tinned but crease and break easily. Anyway I can reinforce them or tips on striiping insulation off very tiny wire?
Hey Don, on very small wires such as 20 AWG or smaller I generally just use my thumbnail to remove the insulation without any trouble. You just need to be careful not to lose any wire strands when you do this. Also you can easily toast the insulation with too much heat so careful use of a soldering iron is your best bet. You would need to twist both wires around each other (like in Chris's video) and carefully add momentary heat and use a very thin solder along with some flux . You can actually purchase a "cold heat" soldering pen for jobs like that and eliminate the heat altogether. Good luck!
This is more useful than 75% of shit I learned at school
so true
As a mechanic you need practical not seating in a class and write down something
@@mohvolgs2808 id say seating in class should only be 10-20% if that
So original....as if they would teach you to fucking solder in school lmfao
i learned how to solder in school haha
Thanks for an extremely precise and well shot video . I learned to solder about 50 years ago, but I haven’t done any for at least 20. You covered everything I used to know, plus some things I was never taught. Thanks for making it easier than I remember.
This may be the BEST video I have ever seen on YT. So well-versed, well-explained and easy to hear and understand. I've soldered before, but I never knew how much I DID NOT know about soldering until today. Those 7M subscribers are well-deserved.
The second method is the style that NASA teaches Astronauts. Strip at least an inch back, pre-tin the wires, bend 90° two-thirds of the way back on the stripped section, twist the wires around a minimum 3 times on each side, now solder the wires. The goal isn't just a good electrical connection, it's a solid mechanical connection that doesn't have weak spots around the solder joint.
Thanks for sharing! Awesome info.
Just NASA alone make it better option.
Forgetting to clean off your rosin with alcohol after soldering.
Wow. Thanks for the info. But in cases where you don't need mechanical strength, i think the other method would have better transmission of electricity. Right? It's more contact.
@@jonathankr There is an important thing to remember about soldering, the lead and tin in solder have a significantly higher resistance than copper. But, due to its small size, the resistance of the solder joint is likely several orders of magnitude less than the overall resistance of the wire, and you already would need a piece of scientific equipment to accurately measure the resistance of measly any wire on a car. Twisting method would theoretically give you a better electrical connection because there is more wire involved in the connection. Twisting also gets the wires touching in a lot of area, which reduces the distance through solder that the electricity must travel. Crimping actually gives you the best electrical connection.
Blown away by how good this tutorial is... Holy crap. Literally the best tutorial I've seen on anything.
The best indeed
yeah, it's like he thought about it, planned it out, and then was willing to reshoot to get the correct example rather than just go "well, that's not what i meant to do. but you know what i was going for, so just do that" like a noob trying to give expert advice
Thank you. I really knew nothing about soldering until I watched this. I feel very confident to solder well and safe!
Glad I could help
I've been soldering for over a decade and didn't realize how much I've missed out on and you covered it in such a simple way without making me feel like an idiot. Thank you!
I've soldered for a living for the last 14 years, and this video is really excellent for people interested in soldering. The information here is quick, thorough, and most importantly - it's accurate. The only extra tip I would recommend is cleaning rosin flux residue off rubbing alcohol using a stiff bristle brush prior to the heat shrink application. Very well done!
I haven't yet watched through the entire video, but I must say that this is one of the most direct, chronological, detailed, tutorials I have ever watched. You list and link the tools that people would need and explain the differences amongst different tools and materials, adding in information to help further clarify our understanding of the concepts. No fluff, no wasted time. Straight-forward, detailed explanations. This was great.
did we watch the same video? packed it in at 1:50
@@davidmg1925 What do you mean?
YOu have a different idea to direct that i have. eg did you really need to be instructed not to solder outside a petrol tank. I lost it completely when he started advising about ventilation.
Bruh, its chrisfix here! Not chriswasteyourfuckingtime
I didn't read your comment yet but it was one of the most pointless and spammy type of comments that wastes time and storage space. It was a brilliant comment thank you.
Chris I came back to this video after having a really ugly soldering job with cheap tools and lack of materials. I decided to finally invest into proper soldering tools and do everything the right way. After trying it out with the right tools I was really impressed at how well it came out. Your video is especially helpful in understanding where I needed to improve my process. Thank you for putting so much detail into your work!
I use to be afraid of doing any DIY's to my bikes and trucks until I started watching this guy. With the knowledge, I'm no longer scared and this dude here has saved me massive amounts of cash with these videos. Major respect to this man
I clicked thinking I knew how to solder as I've done it since I was a kid. now I am mind blown. lol. thanks chris
Glad the video taught you some new tips and tricks!
*Thumbs up so everyone can see!!!* Hey guys, thanks for all of the support! After 3 years of working 7 days a week on KZhead, I just got back from a family vacation (which is why I did not post a video). I am back and pretty much all caught up and I will be drifting the #DriftStang this SUNDAY!!!! Wish me luck and again, thanks for all of the support! You guys are what make this channel tick and I hope you continue to learn a lot and enjoy the videos. Be sure to follow me on Instagram and Facebook so you can get updates on when videos go live and what I am doing every day of the week! Instagram→ instagram.com/chrisfixit Facebook→ facebook.com/chrisfix8
dope hope you had a great time
Good luck on Sunday!!
+Chrisfix I have a question are you left handed or right handed???
Thanks a lot guys!!!
hey yo no problem if you missed a video you deserved a vacation good thing you enjoyed
7 years on and your video is still teaching people. That was a really excellent how to video, just what i was looking for. Thank you 👍🏻
One of the best lessons I’ve ever seen on KZhead. Pay attention, everyone! And never prevent yourself from learning a new trick of a trade.
thanks for calling them tips and tricks and not hacks =P
👍👍
This comment ⬆
Collin Weis 👍
Collin Weis 👍
Temoor Ali &
Meanwhile in denmark ''As long as it is touching, We've got power.
lol
🤣
just put the damn electric tape on lmao I do that too 🤣😂
@@cambodiatransportv7482 nah we dont need safety
My car is down to one speaker because the previous owner used this method
This video is 7 years old but man do I appreciate every bit of it, You are such an inspiration and role model Chris, You have saved me and my car multiple times, especially when I did wheel bearings, tie rods and a bunch of other suspension components!
I have 30 years experience in the automotive industry and this was the most informative video I have seen in a long time hats off to this Creator and that's just everybody give him a thumbs up and hit that subscribe button and that Bell
*has been soldering wires for 45 years *still watches the entire video
Well how did he do?
Me too.
Chris is just a phenomenal teacher!!!
Thanks a lot Nicholas!
true
I've been soldering for a good decade now (mostly guitar amps), but I like to come back to video tutorials like this every now and then for a refresher to make sure I'm not getting complacent and missing any detail, and pick up new tips like using dielectric grease. This is easily one of the better ones out there.
Thanks!
If only all instructional KZhead videos were like this. Clear, well-filmed, no fillers, give reasons to why it is done in a certain way. Absolutely loved it, immediately subscribed and will be buying stuff from the links you gave. 13 minutes of my life I don't regret.
Me: "Say solder" ChrisFix: "Solder" Me: "Now say water" ChrisFix: "Wooder"
This pronunciation seems to be very common by Americans. It's not a bad video though if you need to learn about soldering.
Sodder
@@mfmr200: I'd always thought it sounded like Saader, but yes their pronunciation is bloody annoying!
Huh? I have never noticed even an American say water as "wooder." I always supposed that people who pronounce it "wooder" were otherwise in foreign countries.
Sodder ITS FUCKING SOLDER
I wish I watched this yesterday when I was wiring turn signals on my motorcycle. I literally made every single mistake you mentioned, but it still works somehow lol
Ace, don't feel bad, at least you LEARNED something and you SUCCEEDED ! ! ! Cheers from Canada !
Heh, me too on my car.. guess I'll have to do everything again so there's no short or even fire :D
Asus ROG?
I just use ductape, don’t feel bad
Me too
Being a soldering rookie, This was the most complete video of soldering and answered many questions I had. Very well done !!!
If my Z31 catches on fire I’m blaming u 💀
Did your Z31 catch on fire?
@@Chrisgoberrrno response probably
Thanks for showing me a "wooder-proof" connection for my "wooder-sports" trailer lights! You have the best production, best voice-over and most valuable information I have ever seen on KZhead!
LOL
saw dozens of these videos on soldering, this one is the thoroughest. Thanks Chris ! Keep on trucking ! (from France)
After watching over a dozen solder vids, and this video today, you can tell how much editing go's into this video. Just a fantastic job he does.
so you know nothing john snow ... ohh wait MakeFix .
Les vidéos de Chris sont toujours très exhaustifs et vraiment bien faits :). C'est une tâche vraiment simple, mais Chris trouve le moyen de faire un vidéo de 12 minutes dans lequel rien n'est superflu! :)
Thanks a lot man! I am glad you like the video and I do my best to cover all of the important topics in a clear and concise way that doesnt seem boring!
I love that you quickly laid out the steps before actually going through them. I was taught that a good presenter will tell you when they are about to present/teach, present and teach it, then recap what was just presented. Basically going over the info 3 times to really lock it in.
Wow, this is so awesome, Chris!! You cover everything clearly and quickly!! Your close ups really help to see soldering in action!! Thank you!!
your channel is genuinely great my friend
Thanks!
Every time I see you've posted a new video it's like Christmas! Thanks man!
Driveway Auto Body HAHA LOL
I just love these videos. It doesn't matter what he's doing, it makes me feel like I can take on the world. Thanks for another beautifully simple and complete tutorial.
Fantastic tutorial. I have tried this several times in the past and now I see why I was not very good at it. Thank you. Great focus on safety too.
One of the Fastest, most informativest, delitefullest, quickest 12 mins I've expereinced. Tq
Great video. I'm an electronic technician. Over 30 years experience. 2 suggestions. One don't sponge the tip off just after soldering. Sponge it off just before soldering. Leaving solder on the tip will oxidize the solder, and not the tip, the oxidized solder will protect the tip. Also, it would be nice to add in how to prevent and remove solder bridges when soldering on a circuit board.
Solder bridges, I keep scrap stranded 14AWG for cleaning those up. Fan the tip and press the iron down. Also, he said lead-free solder doesn't have the shiny look that leaded does. I use both, and if you do it right, lead-free is just as shiny as leaded.
Great video. This video and 30 mins of practice helped me make some great wire splices. One tip: I did this in a car wheel well and used small magnets to temporarily mount two alligator clips to the frame right underneath the wires. This gave me some control of the wires while soldering.
Watching this right after making my first wire soldering gets me right back into my garage and start it all over! Thank you CrisFix for another great and comprehensive video!
I've always felt the act of soldering is pretty therapeutic for me.
Soldering can make me nervous easily ..
Lol same here soldering at first seem like such a chore but if you just let the solder melt onto the cable it's pretty simple and easy.
It's because of the smoke..it calms your nerves down.
Not supposed to inhale the fumes. ;D
Has Chris ever made a _bad_ tutorial? This is honestly the best tutorial on the subject I've seen. And I've seen many over my career.
Thank you!
3:42 - Everyone's gansta with their rosin core solder until Chris opens up his rosin paste flux
Great tutorial!! Now I know why I had problems with soldering. I was doing it all wrong and made it much more difficult than it was. Lesson learned and you equipped me with much needed information with detailed explanations that will make a huge difference in my future projects.
I have to say, out of all the "how to solder" videos that i've seen, this is the best. Straight forward and simple!
Thanks!
It's not so simple as a beginner, but you'll get it.
Well done! I have never been satisfied with my own soldering jobs, and now I know why. I need to get some helping hands and make sure the solder never touches the tip of the soldering iron. Your videos are consistently practical and easy to follow Chris.
+Jay Grosse awesome! Glad the video was helpful!
Jay Grosse
Jay Grosse and I had the issue of blobbing.
Well said, exactly how I feel. My soldering was never "good" so we will see how it goes!
as long as you heat up the wires enough to make the solder flow into them there is no problem with touching the the tip of the iron with solder.
Your tip for those without high voltage electricity was the best tip by far. I've been using a 1lb propane torch with the tip closed up 75 percent. It just covers the few who live very poor or completely off the grid. In all, thanks man!
Your quick responses only add to the amazing job you do Chris! KZheadrs like yourself so casually teach people important things in life that help
First time ever having to solder wires together. I bought one of those easy off safety switches for my table saw, and since there will be a bit of juice running through them i wanted it done properly. Usually i have to look at several videos to get the right method for doing something properly. I read the comments to make sure people are actually showing the right method. Your viewers are pretty unanimous in this being one of the best videos out there on the subject, even i could follow. Thank you. 7 years pass rather quickly.
Thanks a lot!
@@chrisfix Just finished soldering them. Went very well thanks.
Nice tutorial to infinite free electricity 👌🏻
&^oòķķķo
Illuminati wants to know your location
WhAre is eletroboom
Just use a coat hanger and some damp grass. Don't you even tesla bro?
YES hahahahahahahahahahahahahaha
Butane soldering iron is one of the best tools I've purchased, especially for auto work. No cords and it heats up from cold in seconds. Remove the tip, and it's a heat gun/torch. Love that thing!
Do a search for Weller WESD51. It'll change your life.
@@HeWhoIsWhoHeIs Will do. One thing I've been doing lately is just using a maps torch to heat joints and feed solder into them. That obviously won't work in every situation but for large work outside of a vehicle it's way faster
@@skatedoof My mistake, it seems they upgraded the model. Now it's Weller WE1010NA Digital Soldering Station. You can find it on Amazon for about $110. Turn it on, set the temp, and about 10 seconds later you're soldering. It's amazing.
Thank you so much for labeling this video "tips and tricks" instead of "hacks".
I think that term is overplayed haha
Even your older videos are such a big help! Thanks Chris for helping me through so many automotive repairs
Well done video. One thing to note, the acid core solder is only used for soldering sheet metal(galvanized). The reason why you don't use it for electrical wires, is because the acid can eat away at the copper over time. The insulation on the wire should be unaffected by oil, gas, and acids. Lead-Free solder is lousy. It does not flow nicely like solder containing lead. Rather than the rosin paste flux, buy a liquid rosin flux. You can apply a few drops and capillary action will draw the flux into the strands. Really don't need the silicone grease under the heat shrink. That soldered connection you made w/o the grease and only heat shrink will be there for decades. If the soldered connection is being done on a boat, then yes, use the silicone grease or heat shrink tubing with glue.
"That soldered connection you made w/o the grease and only heat shrink will be there for decades." Not if it's exposed to salt water. Around here they use salt in the winter and it eats through copper wire. An untreated connection will turn into green dust.
+Slicerwizard I guess you didn't read all of my comment.
+electronicsNmore You said his use of grease is OK if the wire is in a boat. It's not, it's in New Jersey where they use lots of salt on the roads in winter. Silicone grease is a good idea under the shrink tubing generally; you never know the end destination of a vehicle after you sell it.
davecc0000 When I used the word "boat", that meant any connection which would be subjected to fresh or salt water. So if you're soldering wires together OUTSIDE a vehicle, then clearly you'd be using heat shrink with glue or the silicone grease. :-)
Then say that. Saying "boat" did not give me (and probably dozens of others) the idea that you implied very watery OR SALTY conditions. Think before you type.
One of the best How-To-Videoes I have seen the past 30 years. I have been soldering a few times every year for 55 years, including building a Hi-Fi amplifier in 1971 , and even I picked up a tip or two. Great camera,- editing,- and narration skills too!
Awesome! I’m glad the video was helpful!
Great video, thanks! I just wanted a quick refresher before I soldered in my new car stereo harness and this was great. Pro tip: the Lineman's splice is meant for wires that are under strain; i.e. being pulled on the ends like the wires going to your house from the utility pole.
Still such a great video 7 years later. Everyone testifying that it is great and covers every point, gives me the know how of what to get, and how to fix my current wiring problem, my power windows. Thank you!
The best soldering tutorial i've ever seen. Thank you.
6:25 "Now just squeeze down on the strippers." That was last Friday. Today is Tuesday, and I'm soldering wires.
lmao
You are a natural talent, I don't regularly compliment videos on how to but my goodness you are fantastic!
Chris I have enjoyed your videos for years. Anytime I need to work on my vehicles I come here to get your angle on how to do something. Your videos are well made and your advice offers a lot of value in a time where real value is hard to find.
hey Chris can i request a engine bay cleaning video?
thus should be done
I second that! I would LOVE to see how to properly clean the engine, and it's compartment! :)
My mom's car engine bay is dirty...
Been wanting this too. Just to know what I need to cover so I don't short stuff out.
+MTBVegan Rich just cover the obvious stuff lol. Don't overthink it.
Waiting for chrisfixes new vid was like waiting outside the Apple Store
I don't like Apple.. Not the same xD
and we're not ChrisFix sheep?
I don't go to apple store sorry
As an Novice RC racer with very little Electrical wiring background (Does 3 months of Electrical Shop class count in high school back 15+ years ago?) I am more than confident enough to actually start soldering! Thank you for the tips and tricks of the trade, simple, effective and the message is clear as day. Thank You!
Chris Fixer, thank you for this video. I needed to know this valuable and quality information on soldering. I just bought a soldering iron and needed to learn how to properly solder wires and get a good introduction into this topic. I had no idea what the sponge "was" for in my kit I bought, but now I know. I now know there are soldering guns and irons. Thank you!
Dude thank you Xlnt. lesson! You are the Ruler of Solder & Gammhora.
That was really helpful! I was cold soldering all the time! Thanks, Chris!
This is the cleanest most professional electrical work I have ever seen in my life , Perfect Job Chris
This is the 1st and only video I needed to see about wire soldering. Chris fix is just amazing, and the way he speaks is calming 😊
Well I've been cold soldering this entire time.. Gotta visit some old projects now haha
Can I use cold soldering on my medal upper false teeth?
Can I use cold soldering on my upper false teeth is it safe?
Lmao same I e been getting frustrated
Well if you're putting those into your mouth, then no, absolutely not, lead is very very harmful to the body.
I always wondered why none of my projects actually worked.
the cold-solder melting at 11:53 was low-key satisfying
this needs more likes... also I totally propose an entire video on cold-solder melting
This is the ONLY video that demonstrates tinning, cleaning, and soldering; and when to do those things.
Thank you for this video, I looked for a video like this 11 years ago and only found useless things, that didn't explain anything, youtube has gone a long way, I appreciate you explaining everything, feeling more confident to tackle some projects I've had in mind.
One more solder tip. Don't solder naked (or where solder can drip onto exposed skin). Ask me how I know.
*sigh* how do you know?
Oh, I know, you tried docking with the tip of the soldering iron
Let me guess, you soldered a joint and the some hot solder decided to splatter off the joint and land right on your nuts?
That is why the goggles, too. I can't count the number of solder splashes I have scraped off my glasses lenses in the last 50 years.
also don't fry bacon in the nude
5 years later but I’m so glad I found this video!! I’m working on small led fixtures to make cool toys and costumes for my sons before moving on to bigger projects like installing leds on my Silverado but thank you so much for your advice!! I was doing it all wrong and doing a cold solder! I hope I can get better but surely I’ll get there thanks to your help!!
You were perfect here in this video. I never knew half the things you went over. Luckily nothing I ever soldered was a risk to anyone or anything but I will use your instructions on the up and coming solder job I need to do. Thanks a lot of the great tutorial.
Chris I give you a Pat on your back!! Ladies and gentlemen this is how you do a “How to tutorial for everything “. For sure top 5 how to videos on KZhead. Chris I really enjoyed watching your videos. Everything about it was just perfect!!!! Keep doing what you do bud and I’m now going to be a long time subscriber. I do all the same thing you do. Been doing 12v ‘s and low voltage wiring for over 35yrs. I’m certified and ticked with red seal . Keep up the exceptional job. Thanks Diven N
I’ve been soldering for years professionally and you hit everything perfectly, well done. This will allow folks to get the most out of their hobbies.
Excellent!!!!!!!! You've given all the information. Grand!!!
This guy is on another, deserves every cent he’s made on KZhead, what a tutorial. Even a deaf person could follow it.
I have always wondered why my soldering was useless, because I was taught at school to "cold solder" again another reason why school wasted my time. I have learnt more from you videos than I ever learnt at school. Thank you for all you videos you show in detail step by step you explain everything and you take pride in what you do.
I appreciate this guy's work so much!! He puts so much effort in the videos, and they turn out to be amazing. This will definitely help many people. Keep at it man! Maybe you will even have your own show at a television channel!
I use the same method of sealing the wires with dielectric grease and heat shrink. Nice tips.
Thanks Mark!
I agree - don't know why I never thought of it.
This video showed me a lot. I could never master the art of soldering but after watching this video I see what my mistakes were. Thanks!😊
Just when I thought my soldering skills were just fine I see this. Excellent tips and directly to the point. Well done. Thanks!
*"Perfect soldering tutorial lesson dosent exis-"*
Perfection
well that is more than a professional job. hat is up for ya, dude.
I just got all the items and did foams soldering of wires today and it worked great. Thanks Chris for sharing all the tricks of the trades
Great video, I learned a lot! If I solder on old wires, I always use steel wool to remove any oxidation from the copper. Before covering the connection with the heat shink I check the solder for any sharp points with my fingertips and remove them with fine sandpaper if needed. Remember that the soldered connection is not flexible and that both ends of the connection are prone to fatigue. Chosing the right location of the connection and having enough overlap of the heat shrink can reduce the risk of breakage.