When i touch my rollers i am only able to spin 1 when i touch it. The other 2 rollers i can not spin them. Should they be spinable when i touch them?
@franciscomaldonado335 Жыл бұрын
I'm not clear when adjusting the helix cap with the clutch installed on the machine. You say to install the threaded rod - so you need to remove (and retorque) the clutch mounting bolt each time you adjust the helix? Thx.
@moslereverett Жыл бұрын
hey! Yes, you must remove the secondary bolt each time to adjust. Very simple
@aftermarketassassins5491 Жыл бұрын
Also do you sell the TORSION SECONDARY SPRINGS? I would like to order it all together.
@scottscott53013 жыл бұрын
See Here: aftermarketassassins.com/products/ols/products/aa-can-am-x3-adjustable-helix We suggest the OEM spring as we found it to work best. Thanks!
@aftermarketassassins54913 жыл бұрын
How do I get one?
@scottscott53013 жыл бұрын
I am currently running this helix right now. only a few miles on it but i would like to bring my RPM range up a bit. i am at 7900 WOT and would like to be in the 8300-8400 rpm range. do i need to back the pressure off the spring?
@johncaughey61192 жыл бұрын
You'd actually want to increase spring pressure to increase RPM. If you are in H1 (hole 1) now on the quick click setting, go to H6 which should gain you more RPM. Keep in mind peak power falls off on a stock tune around 8000-8100, and with a tune 8200-8300 is max RPM @55mph or the clutch does not load the engine enough, and boost will taper off quickly.
@aftermarketassassins54912 жыл бұрын
Quick question. When I took my secondary clutch off my x3 120 the bolt had washers but there wasn’t one on the transmission shaft. Is it supposed to have one between the transmission shaft and the secondary?
@therowdyboysnetwork28273 жыл бұрын
You will just have the bolt, and a washer that is stepped to hold the secondary clutch on. The stepped washer sometimes stays in the clutch.
@aftermarketassassins54913 жыл бұрын
No washer on the back side?
@therowdyboysnetwork28273 жыл бұрын
@@therowdyboysnetwork2827 No washer on the back side
@aftermarketassassins54913 жыл бұрын
Thanks for helping me out!🙏🏼 I was worried I was missing a washer. These clutches are definitely different from Polaris
@therowdyboysnetwork28273 жыл бұрын
Hi, do you know the name of the tool or part# to compress the secondary to be able to remove the belt?
@drd1924 Жыл бұрын
You should have an OEM one in your tool kit, but we have this one that works well: aftermarketassassins.com/products/ols/products/can-am-x3-belt-removal-tool
@aftermarketassassins5491 Жыл бұрын
When are they going to be on the website?
@coltenthompson65923 жыл бұрын
Helixes are live! aftermarketassassins.com/products/ols/products/aa-can-am-x3-adjustable-helix
@aftermarketassassins54913 жыл бұрын
Do you have any distributors in Canada
@Kawarthametalsigns3 жыл бұрын
We do not currently, but ship direct to Canada almost every day. Thanks!
@aftermarketassassins54913 жыл бұрын
Can Iuse this system to lower RPMs? My X3 is street legal and on the highway I'd like to drop the RPMs some. Thanks
@rick3446 Жыл бұрын
Installing only our performance 1053 helix in your X3 would drop RPM roughly 200-400 RPM over stock, and lower cruising RPM for road riding, yes. You would want to use spring end hole C, quick adjust bolt hole 1. Thanks!
@aftermarketassassins5491 Жыл бұрын
@@aftermarketassassins5491 Cool I just ordered it. Thank you
@rick3446 Жыл бұрын
No thanks. I'll stick with the evo one. This is way to complicated.
@terryfrome16412 жыл бұрын
They are very easy to adjust and set up, thanks though!
Thx for this tips👍
When i touch my rollers i am only able to spin 1 when i touch it. The other 2 rollers i can not spin them. Should they be spinable when i touch them?
I'm not clear when adjusting the helix cap with the clutch installed on the machine. You say to install the threaded rod - so you need to remove (and retorque) the clutch mounting bolt each time you adjust the helix? Thx.
hey! Yes, you must remove the secondary bolt each time to adjust. Very simple
Also do you sell the TORSION SECONDARY SPRINGS? I would like to order it all together.
See Here: aftermarketassassins.com/products/ols/products/aa-can-am-x3-adjustable-helix We suggest the OEM spring as we found it to work best. Thanks!
How do I get one?
I am currently running this helix right now. only a few miles on it but i would like to bring my RPM range up a bit. i am at 7900 WOT and would like to be in the 8300-8400 rpm range. do i need to back the pressure off the spring?
You'd actually want to increase spring pressure to increase RPM. If you are in H1 (hole 1) now on the quick click setting, go to H6 which should gain you more RPM. Keep in mind peak power falls off on a stock tune around 8000-8100, and with a tune 8200-8300 is max RPM @55mph or the clutch does not load the engine enough, and boost will taper off quickly.
Quick question. When I took my secondary clutch off my x3 120 the bolt had washers but there wasn’t one on the transmission shaft. Is it supposed to have one between the transmission shaft and the secondary?
You will just have the bolt, and a washer that is stepped to hold the secondary clutch on. The stepped washer sometimes stays in the clutch.
No washer on the back side?
@@therowdyboysnetwork2827 No washer on the back side
Thanks for helping me out!🙏🏼 I was worried I was missing a washer. These clutches are definitely different from Polaris
Hi, do you know the name of the tool or part# to compress the secondary to be able to remove the belt?
You should have an OEM one in your tool kit, but we have this one that works well: aftermarketassassins.com/products/ols/products/can-am-x3-belt-removal-tool
When are they going to be on the website?
Helixes are live! aftermarketassassins.com/products/ols/products/aa-can-am-x3-adjustable-helix
Do you have any distributors in Canada
We do not currently, but ship direct to Canada almost every day. Thanks!
Can Iuse this system to lower RPMs? My X3 is street legal and on the highway I'd like to drop the RPMs some. Thanks
Installing only our performance 1053 helix in your X3 would drop RPM roughly 200-400 RPM over stock, and lower cruising RPM for road riding, yes. You would want to use spring end hole C, quick adjust bolt hole 1. Thanks!
@@aftermarketassassins5491 Cool I just ordered it. Thank you
No thanks. I'll stick with the evo one. This is way to complicated.
They are very easy to adjust and set up, thanks though!
Evo is just a hype.
If this is complicated then you’re a lazy bum