Heavy Duty Machining 1000HP Tree Grinder Shaft | Part 1
This video is Part 1 of heavy duty machining a new shaft for a 1000 horsepower Vermeer Horizontal Tree Grinder. We are using our TM-26120G centre lathe for machining the large tree grinder shaft. The material we are turning is a 2.6 metre (8.5' feet) length of 242mm (9.52" inch) 4340 solid bar. This job did not go to plan! The material caused some dramas which created a run out problem the deeper we machined into it.
Join our channel:
We upload new videos every Friday at 5pm AEST! If you want to see more of our videos click LIKE & SUBSCRIBE! You can subscribe to our channel here: bit.ly/ceesubscribe
Join our Patreon community: / cuttingedgeengineering
To see more follow us on online here:
Instagram / cutting_edge_engineering
Facebook / cuttingedgeengineering...
Official CEE Merch shop: www.ceeshop.com.au
Check out our AMAZON store and explore our favourite finds that we use in the workshop:
www.amazon.com/shop/cuttinged...
About Us:
Our channel is all about showing you real life machining work from our workshop on the Gold Coast Australia. We specialize in manual machining, hydraulic repairs and heavy fabrication for the earth moving, mining and civil construction industries. So if you're a machinist that wants to see some big gear in action be sure to subscribe to our channel right now. We upload new videos every week that show lathe machining, milling, welding and all the good stuff that comes from a machining workshop. If that sounds like something that you would enjoy seeing, then make sure to join us by subscribing!
Music: www.epidemicsound.com/referra...
#australianmachinist #machineshop #machinist
Hey viewers Happy New Year! Our first video for 2021 is part 1 of machining a new shaft for a 1000hp tree grinder. This did not go as expected and we had some serious issues with the material. Hope you enjoy the video 😎👍 Subscribe and hit the bell icon to turn on notifications so you don't miss our weekly uploads. 👇 🤳 Follow us online here: Instagram instagram.com/cutting_edge_engineering Facebook facebook.com/cuttingedgeengineeringaustralia/ Official CEE Merch shop: www.ceeshop.com.au
Возьми меня к себе я буду бесплатно работать,я хочу у себя потом такой бизнес открыть.
Is this something that the material supplier would replace at their cost?
Think about it though, the poor shaft is in for a life of grinding stumps, was there anything wrong with the first/original one? it failed, tried to be repaired but failed again....nice and noisy when failing i bet. So it is a crazy job this shaft is asked to do in it's life. But hypothetically, what if you made a perfect shaft, it could possibly work a tiny bit less efficient then the "banana" you have....as you said, you went for some flex... I'd like to think it could be worth the punt, what would the cost of labor and material be now, what if it failed after X? hours, what if it worked perfect longer than the original, can it do that much damage running out so little....FOR A TREE GRINDER MAIN SHAFT!!! How much more labor to finish it, X? more $ but i think it could be worth a try, what bearing can it hurt, what is the perceived problem this would cause...for a tree grinder?
Has the treatment that unfortunately made it worse...also made it stronger now? That could become a benefit for this lump of steel? How balanced is the drum it spins in the first place, could this be a deliberate "banana drum shaft experiment"? So? it could have a weird vibration but all that must become irrelevant once it starts grinding.
One last point maybe, even from 3:50 to 3:59 (nice close up slo mo again but need closer and slower) that shaft was showing it was going to fight, making spring swarf all the way doing that first support groove, it just seems to have wanted to be a lobe...can it be basically flexing your lathe and itself to keep this "imperfection"? But i still think you give the customer a chance to save as much as possible from the RUD (Rapid Unscheduled Disassembly *Elon) it's good recording your work like this so you can show what happened but why not still try it?
As Woodworker we bump into Problems with stress and bowing quite often. So we use heat treating as well. We heat the wood up to about 1000°C in the stove and this solves any Problem. :-)
But 1000 degrees C would cause the wood to.... Oh. I get it.
Yup! Solves the problem every time. I've also noticed that as the prices for wood increase the more common the problem becomes. Happy New Year to everyone wherever you happen to be in the world.
Right on.
As I work on making swarm traps from scrap 1/2" ply, I'm come across pieces of warped madrone, and having great success at heat treating. Toasty warm here in Origun, USA. No E. Happy New York 🇺🇲
@@timothyball3144 First Hermann had me like "umm what technique are you using, that would simply create carbon" (im a carpenter but I also deeply dive into new techniques and skills to broaden my knowledge) then I went to comment like yours and foudn your comment. To be fair, he is not wrong. XD
Enjoyed the video about the bent shaft that kept throwing out. I worked on a copper mine in the 70's in Africa and we often made shafts. I remember shaft turning carbon steel pump shafts and larger shafts for the mining operations. With long shafts with a ratio of diameter to length over 1:13 one had to keep turning end for end and between centres. There was no heat treatment, we just kept turning end-for-end with light cuts until the stresses eased out of the shaft. Later in life running my own company similar to yours we found alloy steel shafts needed heat treatment. Not annealing, but stress relieving treatment. There is a British Standard available I believe, forget the reference number now. We would rough out to plus 10mm on diameters stress relieve 1. then further rough out to plus three mm on diameters and stress relieve 2. and then rough to plus 1mm all over. We would not finish important diameters leaving them to the very last. Where large keyways or drilling operation were involved axially we left bearing diameter's until the keyways had been cut. If a shaft is absolutely critical sometimes it is best to let it rest for a week in the roughed out state in addition to stress relieving. I found a company in Saudi in the 80's that had spent a lot of work on a large shaft 6" diameter x 6ft long and ground all over which had moved after grinding and the throw was 4/10 thou. That is 0.0004". The shaft had been rejected. To the comment someone made about cheapskate customers supplying poor quality steel, I would say no billet or bar is always perfect. I have had to reject stainless steel bars with cracks in the core. It's part of life I guess. I'm not familiar with the steel designations given in the video I only remember the British EN series. From memory the most stable steel available for shaft turning, steel that did not move, was EN14. It's tensile strength is little better than 20 carbon steel i.e. 20 tons tensile, but it is stable and easy to cut, also resistant to cracking. Customers often choose better quality steel for a job, but it is not always better, the steel has to suit the application. I remember a customer coming to me in desperation, he had used every type of alloy steel for a railway application where there was heavy vibration. We eventually tried structural steel grade 43A and it lasted 20 years. No cracking and the welds held. I think you could save a lot of time by buying a small horizonal milling machine for boring out gussets and beating. The Cincinnati 2E is ideal for such things and bigger millers for the larger work. I am very impressed however with the automatic welding device for line boring. I've been retired now 20 years, and I suppose I miss the old machine shop work. But better to watch your videos. Best wishes, your videos are fascinating and I have earned a lot from watching.
Awesome story, thank you for sharing!
I've probably spent less than 10 hours running a lathe, and I'm probably wrong, but, when you started cutting, the free end had obviously quite a bit of runout. Thats fine because there was plenty to remove. I think the problem didn't occur until you flipped it. You should have adjusted the chuck for zero runout on the indicator, left the steady rest where it was, and all the runout would have transferred to the free end. Same as before. I'm sure sometimes material will spring after removing a good portion, but in this case i think it was operator error.
You’ve learned a lot?!? That’s very humble, and a real compliment to Kurtis. And yeah, we always miss the shop.
That's one hell of a Welsh name you got there, mate.
Great comment! 👏👏👏
I just retired from a machine shop in Philadelphia. After rough machining we always send in out to be stress relieved , before final machining.
Just came across your channel and enjoy the content. I’m a manual machinist and make these shafts often and can keep them running within .001” the whole way but they can be very temperamental .Couple things I have found/been taught. Number 1: 4 jaw Number 2: face up the ends of the shaft and have it banked against something solid in chuck Number 3: rough in the big OD the length of the shaft before turning the ends. For one it gets all the stress out from the beginning that’s in that top layer. It also reduces the size of the square shoulder which will warp the shaft Number 4: step in your radius while roughing so it looks like a staircase. This will help with the large square shoulder and help keep it from moving. Radius will always fit under a 45% angle. Say you are taking 0.100” perside when you get to the end of your cut stop 0.100” sooner the next pass until then go step it down some more when done roughing before finish passes. With a radius that big on a shaft of that length you want the radius on both ends roughed in before finishing either side or you will risk bending it. Number 5: gotta be careful with the steady rest can bend them with that also. Number 6: I scraped one the other week because I got some unexpected taper on my last pass. Besides that nice work and I envy your lathe. I make them on a 1940s 20” American. That rapid traverse on the carriage, DRO and the chuck for the tail stock make me drool.
@Devin Shock I've never seen Kurtis talk about runout on his scroll Chuck, but on these large shafts I imagine a 4 jaw would be better, and your advice about the steps in the shoulder seem sound. I watch ABOM 79 on KZhead (Adam Booth) and he does or has done many gearbox shafts of that length and girth and he uses the same techniques that you mention. Kurtis is a great machinist no doubt, but I think he would benefit from being a little more patient in his techniques. It seems he is always looking for the fastest way to get it done, which is great for his shop, as he appears to be a one man crew, but the fastest way is not always the right way, especially in manual machining large shafts, or machining in general for that matter. Enjoyed the video. Sometimes it does not matter your technique, a shaft can just be to out of wack. Strange though, I've never seen Adam Booth have this issue, and while I've not seen all his videos, I've seen a lot, and many are of this type of machining, and on much older machines!
Many milled parts are roughed out before normalizing. I have even hung vertically positioned while HTing.
9 and a half banana's... spot on !
😂👍
& 2,000+ lbs, that is bananas!
>bananas i see Kurtis uses the Imgur scale of measurement.
At least he didn't use precision guesswork.
Listen, I'm a machinist from America and I can tell you that is pretty funny. Waiting for the attempts to say standard is better than metric.
Enjoy your videos . Your explaining each step of the job is great. My grandpa was a machinist for the Pennsylvania Railroad in 1937 to 1960. He was excellent at his trade. Had his own lathe & tools , unheard of in those days. No one but he could use it. He was that good. He would have loved to see you work. Love your pup...your wife is great behind the camera, you’re a good team. God Bless
Hey mate, I’m an Aussie, not a machinist. But I have recently found your channel and have watched them all in a couple days. Love your work and genuine skills. If only I could turn back time, I’d love to do what you do and the skills you have. Thankyou!
Mate, having turned hundreds or more shafts like that, the only way to ensure it stays straight is to run between centres in a 4 jaw (or a bored 3 jaw), rough it out, let it sit overnight, then finish it. Heat treatment is sometimes needed, but only usually once in a thousand. If you rough it with 10mm green on each end, or maybe you can get away with 5, then let it rest, even for a couple of days, then face off the green and re centre it and run it between centres again, it’ll run true, because you’re not gonna be removing heaps of material in the finishing cuts to put heat in and stress it out. If it was 4140, it would be much less susceptible, and 1045 much less again. But 4340, you have to look after it.
@madaxe79 Time stamp 17:29 Yeah, have to agree about preferring the 4-jaw for this sort of job. About 0.7 mm runout at what looks like a foot or so from the chuck is bloody huge. I wish Kurtis had shown footage of clock readings closer to the chuck to give us all a better idea of the shaft curve. I ain't ever seen such an extreme level of internal stress movement over such a short distance. I'd be inclined to ask that 3-jaw some very probing questions over such readings on the dial.
Wise words there
@@lordchickenhawk 4 jaw 4 sure
@@kevinpeppers4311 4 jaw 4 sure.... heh heh, nice rhyme matey I'll have to pay that one :)
Also, while you've got material left, bang it hard a few times with a big steel hammer. The vibration will relieve some of the stress.
Interesting to see how different shops use different ideas to do the same type of job and I enjoyed seeing how you got it done. I used to do large commutator shafts of a similar size, and we had a few rules.... 1. No steady rest adjacent to the live centre. 2. Kept looking for another steady rest. 3. Span of less than 2 metres between Chuck/Live centre and steady rests, adding a second steady rest as required. 4. Opposing interrupted cuts for the two steady rests meant that we could send the material back. That interrupted cut behind the steady rest along the unsupported centre section had my teeth on edge...some evidence of sagging at the 12:00 mark. Building up heat in the work piece could explain some of your later run out issues as due to the thickness it likely wasn't heat treated fully before hand. Thanks again for an enjoyable video.
What are the pointers to sagging at the 12 min mark?
@@georgemarshall6657 That, I also would like to know!
@@1kleineMax1 A few seconds later i can hear the sound of the cutting ocillating up and down which suggests the cut is getting deeper and shallower once per rotation which means something is going on with the peice as the cut sound on anything other than a cleaup pass should be fairly consistent as you should be removing an equal amount of metal all around the work peice
@@georgemarshall6657 A few seconds later i can hear the sound of the cutting ocillating up and down which suggests the cut is getting deeper and shallower once per rotation which means something is going on with the peice as the cut sound on anything other than a cleaup pass should be fairly consistent as you should be removing an equal amount of metal all around the work peice
on long shaft I always turn steady band closest to the chuck first and work towards the tail with at least 3 bands Always 2 cuts to cut steady band. Lastly re-machine the centre. repeat this process a number of times depending on the diameter and metal to be removed rough out the entire shaft first and allow to cool. Machine new steady bands and centres again before finishing. Just my way. hope it helps someone.
That was just insane. The amount of work that goes into thinning that rod and turning the whole thing is crazy. You are amazing!
8:36 Shop dog. Best part! Happy dog.
I am in awe of Karen’s editing skills… Just awesome work, wish my wife could do this kind of work too. So BRAVO Karen for your work and skills…👍👍👍💯💯💯👏👏👏👏👏👏👏👏👏👏
The way this year has gone.... This is about what id expect.
yep my exspirience too you get a broken shaft its going nowhere good no fucking way no matter how strong you make it i had the same problem on a industreal drill press 500 euros secend hand 2 days in shaft breaks new motor 100 euros through the magic of machining i fucked it every way possibel and got it to work INBUS kv10.9 /24x100 br din912
LOL!!! I hear ya!
Thank you for showing us the issues that are acquainted with doing such a job look forward to seeing how this would be handled
Really enjoyable to watch Curtis go about his work. A real craftsman!
You two put a great video together. I always wondered how these giant machines worked and how they get repaired in a shop, etc. From Detroit, thanks for the look into the how to's.
.... nothing more beautiful than a freshly machined piece of quality steel! I guess I'm just wired a little differently? I just can't help it. Some people go nuts over fresh baked bread (I've got that bug too) but, for me, it's fresh cut steel! :)
For me it is freshly cut Ceratapetulum Apetalum (Scented Satinwood) - en.wikipedia.org/wiki/Ceratopetalum_apetalum
I really enjoy watching you guys perform your magic. Thanks for sharing this with me.
New to this channel. Been playing catch up with your previous vids. So much better than listening to 30 mins of part and stock numbers. Just gets on the job! Love the technical explanations at the end of each vid.
Hi. The problems you have had are due to the stresses caused by turning in the material. It is normal. But to avoid so many problems, you should do the centering points later. The material is always going to twist. It is a material of a very high quality and resistance. I really like the tailstock grip plate. From Spain, greetings. Very good work and very good channel!
I just want to say that I love your videos. The work you do is first rate and extremely interesting.
Just subscribed,machinist of 35 years in the UK and still learning,looking forward to Part 2 of this!
I remember the first machine shop I worked at and one of the things they made were impeller shafts about 10 feet long and about 3 inches in diameter made out of 4140. They would always warp .050-.100 once rough machined and left over night due to the fact the steel isn't stress relieved.
Left overnight in an oven, I hope.
Interesting method. Put 10 tradies in a room and everyone will have their style of machining.👍
I put three tradies in a room and ended up with five opinions. Worked a treat!
I learned from old tool and die makers...they threw my mistakes across the sho...lol
That's a 2020 piece of rod, you should've waited for the 2021 model 😂
Ha, ha... laughed my arse off! 🤣🤣🤣
Yup, exactly, should've waited. LOL
Better make that an 2022 rod. At least, if it's an European model :)
2021 are difficult to machine. have you bot heard of chip shortage?.
I'm retired but watching these vids makes me feel as though I'm beginning productive but please watch the profanities my dog watches them with me😁
Nice thing about watch old stuff, Part 2 is right around the corner. :) Edit: Seems I already watched Part 2, it be Liked. Gonna watch it again.
The machinist is a real pro. Such exacting work and knowledge to machine these parts is really impressive.
I can tell Your a Good machinist hence looks like You've been doing it all Your life thumbs up
Wow I never knew that could happen in that large of material. Great info 👍 👌. Your teaching teaching along just by doing your normal work 👍. Keep up with the videos. Very helpful.
The bloopers are amazing :) Love this!
Happy new year! You and your Mrs's make a fantastic team! Keep up the good work. Give wonder mutt an extra bone for keeping everything running smoothly.
Thanks for watching mate appreciate it!
"My favourite piece of swarf". I laughed like an idiot for at least a minute..... Happy new year Kurtis and Mrs Kurtis. I hope things go well in 2021.
Hey mate hahaaa glad you liked that one I'm still dirty on her for throwing it away 🤣
@@CuttingEdgeEngineering "How could you? My Mum gave that to me!" 🤣🤣
@@CuttingEdgeEngineering Worse! It was obviously your LUCKY piece of swarf, & hence the steel banana
@Cutting Edge Engineering Australia, I'm glad that I'm not the only one who has their favourite swarf, I wasn't going to tell anyone about it as I thought that it was kinda weird! I've noticed that ABomb also keeps his favourite swarf too, but his swarf weighs 75 grams or 0.165347 bananas!
There is something about watching milling that is relaxing to me. Thanks for the great video!
Lathe: Cuts a piece of metal KZhead: [Music]
2:21 Lifting metal KZhead: [Applause]
It was good to see your security officer come by for a consultation in trying to figure out a way to salvage that material. Here is hoping that 2021 will be a better year for all of us.
Your dog is so cute and so sweet. I like every moment of his videos. It feels like a stress relieving moments during machining process...Great video by the way and I do learn a lot from you.
Great start to the new year!!! Well at least for me it is watching one of your videos. Never would've thought that would be the cause of constant bad runout.
Hello from Northern Ireland, I’m a machinist in a heavy engineering shop and we do lots of screen shafts for the quarry’s! We would normally use a 4 jaw Chuck when machining them and we don’t get a lot of runout maybe 0.2mm
Strange last name there, you a red coat?
I'm missing Abom79 heavy machining video ! You guys are awesome !
So nice to watch a tradesperson work. Taking your time and doing it safe
Just fascinating to watch!!!!! All math, laying out, measuring!! Master craftsman in all aspects.
Awesome video! Never would have guessed internal stresses could be THAT bad.
What a video, bloody banana bar, can’t wait for part 2. Hopefully take 2 runs truer Happy new new year to you and the team🎉🐕
FYI I love the intro to this episode. So we could watch out for things going wrong. Also I love seeing the videos when things do not go to plan. I know it's unfortunate for you guys, but I love seeing how things going wrong gets handled. Thank you!
Hands down, Kerney & Trecker is the best brand of milling machine ever made.
That was a kick in the nads, looked like the heat was coming off in the chips really well, great video.
Thanks for watching mate 😎👍
FANTASTIC VID , LOVE THE CONTENT. KEEP THEM COMING, AND A HAPPY NEW YEAR TO YOU ALL. REGARDS RICHARD.
Can't wait for part 2! Amazing work on all the videos Kurtis. Love that you include the Pitty in the videos. Keep up the good work.
That's a Staffordshire Terrier
That's a seriously fucking crazy insane metal lathe. Like spinning up 900 points on center like that AND having the strength to bite into it. Wild. And I bet they come even more monster than that for corporate machine shops
Ahhhh....the sound of the metal squealing as it’s cut by the carbide, all day long. I love it.
Glad you enjoyed it mate
I worked at a company called SANDVIK and i made the powder for cutting tools, different powders for different tools.
Nice one 😎👍
Hey, I bet a lot of people watching have used Sandvic tooling.
Gotta love it when the customer supplies his own “low grade” material to save money... Was roughing out a customer supplied tool steel shaft on a lathe when it broke apart during a cut. Apparently the shaft was welded together and machined sometime in the past....
Love the way that refer to imperial measurements. Got my xmas viewing sorted anyway, going through all of your vids.
Greetings from America. I've been a machinist all my life and never seen this problem before. In this trade we learn something new every day. Looking forward to seeing if additional heat treating relieves the stresses.
No. No it will not, and I should know.
15:55 One thing I've learned over the years, don't ever slide the end with a run-out into the 3-jaw chuck. First of all there's no way to check the end of the shaft and second, the 3-jaws will try to move the run-out in different direction. As someone mentioned before 4-jaw chuck and working between centers is your best bet. But if it turns out that it's some shitty material, then there isn't much you can do.
I think your 3 jaws chuck is running out of center, I have some experience with these shafts and I do not trust but my 4 jaws chuck, I would say too, that your lathe needs more power and better bedways
well, his method worked and thats what matters so... if it aint broke dont fix it
Seeing you work is a pleasure to behold! You use numerical control machinery with disarming ease! You are not afraid of any job, you are humble and honest. Best wishes for a 2024 full of beautiful things for you and my lady. A hug to "homeless" ❤️❤️❤️
Another great video!! Thanks for sharing it with all of us!!
I love a good cliffhanger!
Happy new year, the quality of the steel makes a big difference, I remember years ago talking to a guy that sold lowboy trailers for hauling heavy equipment and one place that was building the trailer was using a cheap grade of steel and the trailers was breaking in half ,
@denny Barton, the quality of the raw materials makes the end product! That goes for everything in life! You should see my ex-wife!
Tell me please- How does Homeless not get swarf in his paws?? Love this channel! Chris UK
Homie KNOWS when dad NEEEEEEDS a pup hug😮😮😮
I love the raw clips at the end lol
Happy new year mate, I used to machine shafts similar to this one that you are making, we used to rough it out to within .250" all over and then let it sit and normalize for at least 3-4 weeks( its a long time if the shaft was needed ASAP), then do the finishing using minimum radius tooling to eliminate tool pressure on the job. we did as much as we could possible with the part setup without flipping it. TIR we used to get this way was within .002-.003 on the 96" length. Best Regards.
Only been machining for 3 years but wow man you inspire me !!!
I like your explanation on a quick fix or cheaper fix is not always in the customers best interest . but its amazing how many companys will cut corners doing jobs and then not stand behind there work. And if a customer wants corners cut well then its on them.
Good thing you have an understanding customer and supplier, if that was here it would be all the machinist fault and you would not be able to convince them different. Great video, and I have to admire the way you approach the job and do the machining. Happy New Year and all the best in 2021
I'm not convinced, but I would be if I was able to take some temperature readings while that bar was being worked on.
To prove what Jules?
I have ran many jobs that other shops couldn’t run by utilizing proper heat treating for that job.
If you take cuts that keep most of the heat in the chip and not the work, that might help.
"Turns out it had too much Mitsubishi in it" LMFAO haha
Staring at my 2 1996 eclipses in the garage right now with the motors torn all apart. Now I can’t stop laughing 😂
great videos and such a talent. love machine shops and your bloopers!
Great machinist, love watching your work.
Ohhh a part 2 ! Dose he sort it out ? Or dose he have to start again ? Dose Curtis loose his shit ? What’s the pup going to wear ? And will the floor ever be finish sweeping . Now we have to tune back in to find out all the details ! I’ll be back :-)
Lol
Do you do the narration/voice over for 'Outback Opal Hunters' by any chance?
@@TrevorDennis100 No, they all sound like that. LOL
Does...not dose...do you even grammar?
we've ran into that before with castings, we had to rough them, flip, rough some more, stress relieve them, semi finish, heat treat, then finish them. the worst part was every one wanted to warp in a different direction
Watch a bunch of your videos, so I subscribed.🇨🇦 Fantastic machinist, brilliant camera lady and a cool dog. Do love the outtakes you do at the end of your videos, awesome, wish you lots of success with your business and your KZhead.
Your Lathe-cooling is special. I have always cooled the HSS turning tools, drills, center drills etc. directly and sufficiently and never the workpiece itself. You want to protect the cutting edges from wear with it. Aluminum with a petrol can and a brush. We didn't cool the carbide plates at all or as much as you can't with your lathe cooling system. HSS turning tools are considerably cheaper and can be reground numerous times. You will need a chip hook to remove the chips without cutting yourself. The measuring instruments are always read directly on the workpiece and not after it has been removed. This is not meant to be a teaching, we just learned it in apprenticeship training. Keep up the good work, be careful with the machines, avoid working alone with the machines and it's exciting to watch.
I’m at the point now where I click like on your videos before they even start! Happy new year guys!
legend thanks mate we appreciate all the likes!
Sometimes I wish KZhead had an "auto like" feature.
Man dealing with you on a problem material must be a hell of a thing. You are so exact in what you do. These would be all precise answers. leaving no wiggle room for vender.
Upload part 2 please. I cant wait to find out what happens
you have many skills, but with the right tools it seems much easier...great job
Curtis, love you work and ethic, keep em coming....! .. ...
That's an incredible warp... almost doesn't seem possible that it's that bad right next to the chuck (17:12).
As a stonemason, this type of thing was a real downer, totally pull down and rebuild.
I really like your videos. I admire your work ethic and drive to get the job done right. You remind me of my dad, who was a genius with machinery just like you. I have learned so much from you. KEEP DOING THESE IMPOSSIBLE REPAIRS AND POSTING VIDEOS..
What I like most about your videos is your dog. He is great. Greetings from Tampico, Mexico
At the end..looks like Homie was running off to use the dunny really bad!
Hahaaa exactly what he was doing 😂😂😂
I thought the gut truck rocked up. "Cmon dad fuck ya I am starving,!,,,"
That was great, never saw much steel from so many cars ! You did well !
I love how you take great pride in your work. ❤
I'm retired and from my work experience in the IT industry I've realised there are three levels of quality control in overseas manufacturing. Accept/Reject/Australia (there so far away they'll learn to fix our mistakes). Happy New Year to you also David
Awesome videos Kurtis I just found your channel and as a machinist in the states I'm impressed with your know how and machinery, as well I collect ball caps I'd love to get into contact and get myself one of those CCE hats if you send them out thanks
You know after all this time watching and learning off you, I feel fully qualified to… … just shut up and keep watching the master at work! 😉👍😂
Keep it up 🤣👍
All that for one rod. Really makes one appreciate how much effort it's taken to build the modern world. amazing.
That's amazing I had no idea that could happen
Thanks for watching mate
I've been machining for years and never seen it, although I must say I've never machines a bar that size from stock. I've done repair work but never from blank
@@GeneralG1810 quite common with bright mild steel rectangular section, less so with round.
@@chrisstephens6673 Wow poor Kurtis that was HOURS of machine time just wasted
@@GeneralG1810 I've worked oil field equipment, I've seen it before, but very rarely. Almost always comes back that the material didn't meet heat treat requirements, or the metallurgy was a bit off.
happy new year
Cheers mate thanks for watching
Give the bar a Fosters, it always relieves my stress.
Great to be here again, almost 4 years later. Sit back and enjoy the show is how I am doing on a near blizzardy day. Nice chip control. Hard on the boot soles though. When it came back worse than nit was must have been dis hartening. Such a total loss of time and resorses eh.
Awsome. Love your work. Hopefully 2021 treats you well.
Thanks mate same to you
Worked around equipment and machinery my whole life, never machining though. The quality and level of work you do is next level. It seems controlling variables is a huge part of your trade. Obviously you can’t control the stock you’re provided. Can’t “polish a turd” as the saying goes! Looking forward to a lot more of your quality work and videos! Happy New Year!
Hey mate thanks for watching appreciate the support 😎👍
... the saying is you CAN polish a turd though
You can't polish a turd. But you can roll it in glitter.
@@carbunkle9902 didnt we just go over this? you CAN polish a turd
@@bmxscape Send it off to the baby shoe people and have it bronzed. Then polish.
Thank you very much, Engineering, for this nice information. Greetings from Egypt
Dogs really are the best people.
Compliments of the new year.such material need proper procedures to achieve quality. You need to premachine it close to size and take it off the machine for a day to give material room to react(stress relief.usually expose it to the sun) then machine it to size and also watch not to exerts too much force on the running centre. Thats my daily bread stuff. Hahahah