Old 1930 Electric Motor (OLD TOOLS RESTORATION)
In this video you will see the restoration of a very old electric motor, from what I could find out it is from the year 1930 approximately, below I will leave you a little history about the company that manufactured this emblematic motor.
EMF Dordt is the name by which Willem Smit & Co.'s Electromotorenfabriek Dordrecht became known. This company existed from 1910 to 1977 in Dordrecht, in the Dutch province of South Holland, and the company manufactured electric motors.
History
EMF Dordt originated from the Smit Slikkerveer company and was founded by Willem Benjamin Smit. As the demand for electric motors increased, Smit Slikkerveer began to focus on large, specialty motors and generators. Series production of the most common engines would have to take place in a separate factory and a site for this was found in Dordrecht. Therefore, the company used the name: Smit Dordt as its logo. It was agreed that the engines manufactured in Dordrecht should not exceed 15 hp (11 kW). The largest engines would be manufactured at Slikkerveer.
In 1914 the limit was increased to 18 CV and in 1915 to 30 CV. In 1918, however, the demand for engines over 30 hp was also met and now EMF Dordt became a competitor to Smit Slikkerveer. The company name has now been changed to EMF Dordt. The company grew well. The registered capital (NLG 200,000) already doubled after two years (in 1913) and even increased to NLG 1 million in 1918. At that time it employed 160 people, in 1920 to 180. In addition to the factory (three floors) at Korten Parallelweg, the company also owned a factory building in 's-Gravendeelsedijk (including dyers). The 1920s were reasonably prosperous and the company was not even relatively affected by the economic crisis of the 1930s. In 1933, the Vereenigde IJzerfabrieken electric motor construction department became De Vijf in Doetinchem taken. In mid-1932, the NV Electric Machine Company, abbreviated EMO, was founded as a subsidiary, into which the manufacture of household items such as vacuum cleaners was incorporated. After initial success, it was liquidated again in 1940.
Some links of historical interest:
• Bedrijfsfilm Electromo...
• EMF Dordt 1950
Damn son, rewinding a motor is freaking dedication, I watch a lot of restoration blogs. But never have seen that level of perseverance!
At 12:08 I’d be dead in the water. This is courage and knowledge.
Muchas gracias !!! Se agradece mucho el reconocimiento , saludos !!❤️❤️❤️
Rewind is not the easiest thing to do.
Restored more than a few industrial motors. Had a dip tank for degreasing, (#1 cause of motor failure) and an oven for baking the varnish. I let the motor shop do the rewinding....
totally agree 👍
*manually* rewinding a stator isn‘t only labor work, it‘s an art! my deepest respect for this, including professionally folding the isolation paper. of course, the filling factor in the slots isn‘t professional anymore, and continuous perfomance will have go down without a resin impregnation. but the simple fact that someone manages to rewind a stator is really impressive.
Thank you very much!!
Круто
I was thinking the same - hand-winding is a lot of work. Glad to see those skills still exist and that people are willing to share that knowledge and experience.
When he started doing that my jaw dropped.
Gran trabajo!!! Las herramientas antiguas merecen ser recordadas con dignidad, sin ellas no existirían las actuales
muchas gracias !! estoy de acuerdo !
Making new windings for an electric motor is not for the faint of heart. Much respect! It's amazing how little electric motors have changed in over 80 years.
thanks !!!
Hola, muchos de los canales que he visto dónde se maneja este mismo tipo de contenido tienden a ser en cualquier idioma menos en español, me da felicidad saber que existe un lugar donde una persona hispano parlante está generando este tipo de contenido y lo más importante, saber que el resultado final es bueno y visiblemente llamativo. Felicidades sigue así!
Muchas gracias Ricardo !! Estoy muy contento con la aceptación que está teniendo el canal , seguiré subien contenido !!
También me alegro que hablemos en español....se agradece.
y no solo eso, es mas pulcro que muchos canales que he visto, mas detallista.
O aprender inglés...¿No? XD
@@myrelics1 para qué se usaban estos motores? Estoy gratamente sorprendida de ver la excelente restauración!!
Большое спасибо)) Специалисты по восстановлению обмоток электродвигателей это очень редкая, вымирающая профессия. Приятно видеть, что такие люди еще остались)))
Muchas gracias a ti !!
Только у нас на заводе обмотчица сначала замачивала двиг в лаке, а потом в печи сушила. а это так, ребячество.
@@pahab3 по технологии макают в лак и сушат дважды. Но если для себя можно и просто торцы помазать. Особенно, если двигатель будет использоваться редко и не долго. Лак это дополнительная защита от влаги и перегрева.
@@dmitriyyuryewitch7068 Мне кажется там люфты и потери мощности в зазорах? Похоже технология сборки нарушена и что то не донастроили?
@@Ignat99Ignatov Нет))) он такой и есть, там всего 500 ватт и 50 оборотов в минуту. На шильдике все написано.
I have enough trouble washing behind my ears. That sir is a work of art and very impressive. The worked who originally built that motor 90 years ago would think it just came from the factory. Very well done. 👏👏👏👏
thanks !!
Очень интересное занятие ! И полезное !!! Как в прошлом побывал...
Alguien más piensa que debería tener premio Nobel de paciencia y sabiduría ?
Gracias Toni !! No me considero un erudito , solo un hombre más de la tierra que aprende todos los días algo nuevo y le gusta aprender , saludos
Paciencia y orden porque a mi se me hubiese perdido todos los tornillos 😂 y un par hubiesen sobrado.
Mi compa usted ha dejado en pañales a un mago, qué trabajo tan pulcro y detallado. Usted raya la perfección. Gracias por su contenido. Tiene usted el conocimiento de punta. Mis respetos
Muchas gracias a ti Alejandro !! por ver el video y este gran comentario , me anima mucho a seguir dando lo mejor de mi
@@myrelics1 No, no, un gusto poder disfrutar de tan valioso contenido. Quiero atreverme a hacerle una petición, tengo un motor trífasico, qué era de una bomba de agua marca pedrolo, el motor quedó sin la parte de realizar el sistema de agua, es posible que usted pudiera realizar un proyecto de instalación y puesta en marcha para un esmeril? Mi primer pensado era poder hacer un molino de café, pero al no tener tantas herramientas, creo quedarme en el esmeril. Quisiera poder recibir ese conocimiento de instalación de ese motor. Gracias de antemano
@@alejandrom5347 tienes que infórmate de las revoluciones a las que trabaja ese motor los de bombas de agua suelen tener mas fuerza que velocidad y para un esmeril necesitas bastante velocidad
Ese motor o bomba hoy tiene 92años ya de uso....y esta como de fabrica..exelente.best work... **********
La verdadera nunca había visto restauraciones a este nivel y tampoco nunca había visto como se hacía un bobinado. Cuando vi 27 minutos pensé en seguir de largo pero la verdad que valió cada segundo. Mis respetos hacía su inmensa sabiduría. Saludos desde Argentina.
Muchas gracias Sergio !!! Saludos !!
Lo mejor es que no colocaron uns fastidiosa música de fondo, muchas gracias de verdad por eso.
De nada! gracias a ti por verlo !
Exato amigo é pessimo vidios com músicas de fundo principalmente musicas de malandros .
Йлмщхл
Un mexicano vio este video 🇲🇽✌😁
@@JuanAntio-Oz A un español le gusta eso !!😁
Madre mía que valor tienes, ya casi no quedan bobinadores profesionales, cuando te dio corto pensé que lo ibas a dejar como objeto decorativo. Es un trabajo increíble. Un saludo
Muchas gracias! Antonio , merecia la pena repararlo , este motor tiene mucha historia !
Que buen trabajo solo un detalle que no pudiste arreglar .y es la velocidad el motor esta muy lento .
Es de 4 polos 😂... no de 2
To restore this motor from the 30's like new makes you the GOAT at what you do.... Bravo.
Thank you very much !!!!!
(30/10/21) Sin palabras. señor, usted es un genio. He quedado sin palabras al ver a este eximio mecanico, al desarmar ese motor en estado fosilizado y después armarlo con tanta prolijidad. Desde Chile 🇨🇱, le envío mis felicitaciones, asombrado por la prolijidad exhibida. Un fuerte abrazo.
Muchas gracias Edwin !!!
Шикарно! Как можно поставить 1000 лайков сразу за такую работу?))))
благодаря
estos fueron mis mejores 27 minutos.... que gran trabajo señor Dios lo bendiga por su inteligencia mil gracias por compartir sus momentos.
Hola Antonio mil gracias a ti por verlo y por tus comentarios, un abrazo !
Beautiful restoration, i love when old classics are saved. They don't make them like they used to.
muchas gracias
Перемотка статора - большое искусство в бытовых условиях, уважение и поддержка. Красиво!
Но достаточно невежд которые это не понимают и ставят дизлайк
Rewiring the motor, few would have gone that far, and few would know how. EXCELLENT WORK . PERIOD !
Thank you very much!!
10:30: OMG, is he gonna rewind the stator?? YES!!! YOU ABSO-FREAKING-LUTELY ROCK!!!
🤣😂 Thanks !!
จะใช่4:00
No tengo ni idea de que hicistes, a mi me da trabajo encontral el positivo en una bateria de auto, usted ha logrado que una persona como yo que no le interesa la electronica se quide himnotizado por casi 30 minutos - Great job!
muchas gracias Pedro !! me alegra mucho que te guste !!
‘M N9
Grande colega yo tengo mucho trabajo que no tengo tiempo de pintarlos y todavía bobino motores de bombas marelli que tienen 60 años y siguen prestando servicio felicitaciones!
Gracias !!
Holy shit... I'm pretty sure this is the first restoration video on YT where the totally abused and destroyed tool doesn't magically have intact windings... Good job!
😂 Thanks !!
Un trabajo realizado por un experto... El embobinado es complejo y la restauración de todo el motor... 👍, Excelente trabajo de pintura. FELICITACIONES 🇲🇽
Muchas gracias Leonardo , no fue una restauración sencilla pero mereció la pena , me alegro de que te guste !
Титаническая работа, особенно с обмоткой! Просто впечатляет! Мастеру - респект, уважение и подписка!
Gracias !!!!
Обмотку надо пропитать лаком и запеч в печи. Тогда она не будет вибрировать и перетирать изоляцию.
@@user-gs2rv7ml9r Вот это я и заметил. Вибрация и люфты. Вы как раз ответили на мой вопрос что нарушено по технологии. Благодарю.
Not sure you will receive this, but... I believe the maker would wheep tears of joy, seeing how his motor was restored. But, for the stator [or any windings] heat the whole thing up in an oven to ~120° - dip in varnish & leave in for around 20-30sec - take out and place back in oven as the whole thing cools down. Alternate - place in vacuum flask with varnish - take out and bake in oven at ~120° You need the varnish to penetrate and hold the wires firmly in place as the motor starting torque is applied to them. Otherwise, as the wires move, they will rub off their own [intrinsic] varnish and short out. Awsome video. Thank you.
Gracias !!
Lo más interesante y asombroso: Re embobinado del motor. Algo nada común de ver en restauraciones de motores antiguos.
Gracias Karahel !! merecia la pena devolver a la vida este antiguo motor , un saludo !
Es verdad
facebook.com/100010680165476/posts/1407548782944447/facebook.com/100010680165476/posts/1407548782944447facebook.com/100010680165476/posts/1407548782944447facebook.com/100010680165476/posts/1407548782944447//jj L
Aquí en Argentina se re bobinan motores tambien. No son grandes lugares tampoco por lo menos los que estan en mi ciudad pero si tienen un intermediario. Algunos reparan electrodomesticos tambien.
@@ezequielaugustodelcastillo6467 el detalle con los motores actuales es que algunos son muy comerciales Y en ocasiones sale casi al mismo precio uno nuevo que reembobinar. Normalmente se reembobinan motores un poco antigüos o del cual ya no hay refacciones como para una bomba de agua. O aquellos que por la calidad del material con el que fabrican las piezas del motor lo permiten (en algunos casos sufren mucho desgaste) En este caso, el motor es una maravilla, sin duda los fabricaban para poderse conservar, dar mantenimiento.
He trabajado en un taller de reparación y mantenimiento de motores eléctricos y lo que sólo te ha faltado ha sido equilibrar el rotor 😂, es coña; cuando he visto cortocircuito no me esperaba que lo fueses a rebobinar! Muy buena restauración, ha quedado de 10 y además va muy fino. PD. Los motores de hoy en día no son como los que se fabricaban antiguamente, esos eran casi a prueba de bombas y con un buen mantenimiento lo que llegan a durar...
Muchas gracias !! te puedo decir sobre el que pesa por lo menos 30 k hasta las tapas son piezas macizas de acero , los hacían para durar toda la vida .
Soy un amante de las restauraciones y me gustó mucho revivir ese viejo pero inigualable motor un saludo desde Colombia
Saludos !!! Me alegro de que te gustase !!
Es satisfactorio ver cómo queda...si uno pudiera decidir que hacer con la vida yo hubiera elegido hacer esto
Ok mi estimado, si alguirn pudiera volver a reconstruirnos...que seria de humanidad?,,, Pero Dios es el que nos puede recontruirnos y hacernos de nuevo..felicidades..saludos.
el conocimiento es poder....!!! me viene a la cabeza esta frase, después de ver semejante restauración. Saludos desde Argentina.
Muchas gracias Alejandro ! un abrazo fuerte para Argentina !!
I know nothing about motors.... But loved watching you restore it
Muchas gracias Josep !! Me alegro mucho que te guste !!
what an excellent effort. most people after checking and seeing is a short circuit would have bought a new one. Congratulations
Thanks you sou much!!
Would I be right in guessing its an induction motor, never seen an armature/brushes like that, I thought I had patience. Man your in a different league. Patience of a saint springs to mind.
You are correct however this doesn't have an armature (windings on rotor) or brushes, it has stator instead (outside winding). the part that looks like brushes is a switch that turns off the capacitor (used to kind of kick start the motor) once its up to speed (weights go flying out at set speed, disconnecting from the rings and cutting the circuit).. hope that was the information you was looking for :)
Балансировка конечно не очень, но за перемотку сразу лайк. Отличная работа.
Muchas gracias !!
Да тоже понравилось как обмотку заменил.
@@lynmidl86 когда начал менять обмотку, я сразу решил что выкину нафиг старый двигатель и куплю новый
That was impressive! I've watched alot of restoration videos, but this is the first time I've seen someone rewind an electric motor. Well done.
Thank you very much !!!
sí, muy bien, sin embargo, no empacaste esos rodamientos correctamente, por lo tanto, se quemarán rápidamente. debe desarmar y empacar la grasa correctamente. yes, very nice, however, you did not pack those bearings properly, therefore, they will burn up quickly. you need to take back apart and pack the grease properly.
I dont know how you have the patience to rewire a motor like that. Nice job
Muchas gracias !! me alegra que te guste ❤❤❤
This is not just labor......it''s an art. You are very capable & skilled. Keep it up. Excellent job you did here
Thank you sou much!!!
Tremendo. Cuando te has puesto a cortar el bobinado del rotor he pensado "¿No tendrá los c*j*nes de rebobinar eso?". Enhorabuena, un magnífico trabajo.
jajajajaja gracias Fernando ! no fue tarea facil pero se pudo hacer , un saludo !
Yo tambien pense eso.
How nice to see something like this passionately restored . It looks brilliant and from a day and age before the throne away age . It exudes quality
Thank you very much!!!
jaja que bárbaro; la carcasa del motor es ¡una placa" de 1/2" de grosor aproximadamente;nada que ver con la simple lámina de 3/16" de las carcasas de la actualidad. Conocimiento y capacidad del experto para reparar un "dinosaurio" de los motores eléctricos;construyendo un nuevo devanado; lo increíble que pudo encontrar los rodamientos ¡91 años despues!;no cabe duda que antes las cosas se fabricaban para durar. Felicitaciones al experto,es un maestro de maestros. Saludos.
muchas gracias !! la verdad es que esas carcasas pesaban una barbaridad !!
Hermoso !!! Bello !!! Me hizo acordar a mi infancia con un padre industrial maderero. De niño me crié entre motores y aserrín, por unos céntimos, motor quemado, debía limpiarlo y dejarlo libre de toda suciedad. Ya más grande me encargaba de armar las bobinas, renovar el papel prespan (aislante) y dejarlo en condiciones de armarlo. Hice el secundario dentro del área de la madera. Al momento de elegir una carrera universitaria opté por la informática, lo que me alejó de todo ese mundo. A veces siento nostalgia ya sea por sentir el aroma del aserrín o ver un motor eléctrico que no funciona. Handsome !!! Beautiful !!! It reminded me of my childhood with a lumber industrial father. As a child I grew up between engines and sawdust, for a few pennies, every burned engine I had to clean it and leave it free of all dirt. When I was older, I was in charge of assembling the coils, renewing the prespan (insulating) paper and leaving it ready to assemble. I did the secondary within the wood area. When choosing a university degree, I opted for computer science, which took me away from all that world. Sometimes I feel nostalgic either for the smell of sawdust or to see an electric motor not working.
Estoy muy contento de que te gustase el vídeo , y muchas gracias por compartir esta historia de tu vida , saludos !!!
When I saw what he was restoring i said to myself, "If he winds new coils I'm going to go insane." So I'm insane now, thanks.
😂🤣🤣 thank you very much !!❤️
When i saw re-winding im impressed. I have never imagine it from the beggining of the restoration. If i were u i was already done with the restoration when i get short from stator. Amazing job
Thanks you very much!!!
Uma obra de arte . Linda a cor verde martelado. Parabéns!
Muchas gracias !!!
Отличная работа!!! Глаз радуется
Работа с электродвигателем, супер!!! Аплодирую стоя !!!! Молодец!!!
Gracias !!
Woooow, nunca pensé que todavía hubiera alguien que hiciera rebobinado. Me quedé impresionado.
Gracias ! yo es la primera vez que lo hago ...
Mis respetos, sea de 1930 o del 2000, es un trabajo extraordinario. Sos "UN MOUSTRO"..Espero ver un proximo trabajo..👍👍👍💯
Gracias !!
No voy a comentar sobre tú trabajo pero si sobre la dedicación que tienes en contestar los comentarios; eso dice mucho de ti. 👍👍👍
Muchas gracias Luis , intento contestar siempre a todo el mundo
The craftsmanship and dedication you put into rebuilding this motor is admirable.. kudos..
Thank you very much!!!
The best thing about the reconstruction video, it's the music, there's not back music, thank you so much guys 🙏🙏🙏
Thanks!
Mis respetos señor electrico el que sabe lo demuestra Arte en las manos Saludos desde Guayaquil Ecuador
Gracias Enrique , saludos !!
My hat is off to you man! Rewiring an electric stator is no small feat. Awesome just awesome. The entire resto was just beautiful. Congrats!
Un autentico restaurador, no como otros que son mucha lija o pura pintura. Hay que tener mucho conocimiento para hacer todo desde principio a fin.
Muchas gracias Sebastián !!
No se puede colocar mas me gusta, genial el trabajo de restauración, se nota dedicación y cariño a los motores de inducción del gran inventor Tesla, felicitaciones.
Muchas gracias !!
Unbelievable. After 90 years of rust, with a simple splash of remover, all screws loose without breaks. Greets from Venezuela. Wunderbar
Saludos !!
Finalmente qualcuno che ricostruisce anche le spire del motore, e include anche la storia della società che lo ha prodotto. Bene un vero recupero storico. Bravo
Muchas gracias !!!❤️
Felicitaciones por tu dedicación y por el resultado final!!! Te quedó hermoso y eso del bobinado fue una belleza.
Muchas gracias !!
I can't believe you actually rewired the motor. Holy crap that was impressive! Well done
Thanks !!!
That rewiring is so very, very impressive! When all old wiring was removed, I was like so now what... Well, you rewired, wow!
Thank you very much!!!
¡Usted es un Dios! Gracias desde Suiza.
Muchas gracias Marcelo !! Todavía me queda mucho que aprender y ni mucho menos soy un dios 😂😂 pero se agradece mucho tu comentario ❤️
No sabés el placer que me da ver tus videos. Recibe un cordial saludo desde Mexicali y que Dios te bendiga siempre.
Me alegra mucho que te gusten ivan !! saludos desde España !!
I admire you so much, because you even reprocessed the winding! Looking forward to more of your works!
Muchas gracias ! Seguiré subiendo videos para ti
Admirable mi hermano, con tan sólo escuchar: problemas en el embobinado, todos rechazarían el trabajo.
Muchas gracias !! Ese motor no fue tarea fácil !
eres un máquina....recablear el motor, pintar, desmontar, volver a montar....que crack!!
Gracias Carlos !!
Madre, me he quedado loco con lo del rebobinado, felicidades. La cantidad de roña que tenia el motor.
Gracias Andres ! la verdad que se notaba bastante el paso del tiempo en este motor , mucha roña sii...
Y yo 🥴
Вот так ,,оживает" техника. И кажется, что у этого старичка-двигателя тоже есть душа! Так что рано его выбрасывать на металлолом: он ещё послужит и порадует,несмотря на свой почтенный возраст. Автору канала спасибо за профессионализм и золотые руки.
Muchas gracias !!
@@myrelics1 🤝👍
Много ошибок.
Разбод
@@velvv5387 ты прав вд40 так неработает да пусть он старого КАМАЗа ходовку переберет герой сразу
Esse Restaurador é um gênio. Parabéns pelo seu trabalho
Saludos desde Perú un joven venezolano rebobinador encantado cada día más con sus videos maestro
Gracias !! Saludos para Peru
Perfect - a absolute Top Job There are very few on YT who get it managed, to rewire a magnet core - a real joy to watch, thank you 🙏
Thank you very much for watching the video and commenting, the truth is that it was not easy, but being such an old engine it was worth bringing it back to life
Респект и уважение за восстановление!👍👍👍👍👍🙂
Спасибо !!
Best restoration I've seen in a long time.
Thanks !!!!
Sinceramente estoy impresionado. Mis respetos y admiración hacía tu persona y a tan formidable trabajo que haces. Sencillamente excelente. Saludos desde Villahermosa Tabasco México
Gracias!!! Saludos para México!!
Why do I have the feeling this guy can do just about anything? I'm impressed.
Thank you very much!!
Perhaps you are not so good with your hands? Maybe? 👌
Es un profesional con mucha virtud, paciencia y sabiduría sin tanta habladera. wao!! Es increíble 👏👏👏👏👏👍👍👍🔧🔧🔧
Muchas gracias !! ❤️
B be Go
Sim sim
impresionante !!!!!!!! hay cosas que parecían perdidas, como tu vocación, pero lo as resurgido y de la mejor manera . felicitaciones !!!
Muchas gracias !!!
I used to work in a motor rebuilding shop, we would remove the old stator windings by baking it in an oven to burn off the varnish. They come out a lot easier afterward. Props to you for manually re-winding that bad boy, never seen someone do it without a winder.
Yes I was astounded by the hand wound method this fellow used . Must have a great focus on his work to make it pan out and then how he stuffed the windings into the fields[ or whatever those segments are called.] !
Impresionante, se merecía dos partes el video, muchisimo trabajo, y además trabajo fino
Muchas gracias Andrés !
No me esperaba el rebobinado, increíble trabajo!
Gracias Ref Jim !!
Unos de los pocos videos donde si restauran no solo maquillan. grande crack
Muchas gracias !!!!
brutal, todo el video es perfecto, planos de cámara currados y edición que facilita el seguimiento de la restauración/reparación, el despiece usando muy poco martillo, el arenado y pintado de forma profesional, el rebobinado con su diagrama dibujado para entender las fases, felicitaciones en mi opinión este canal de los mejores en este tipo de contenidos , bravo
Muchas gracias !! me alegra mucho que te guste el contenido del canal !! todavía tengo mucho que mejorar .. SALUDOS !!
Increíble trabajo. Sigue así. Muchas de las restauraciones que veo nunca son tan complicadas. Buenas manos. Espero que sigas creciendo
Muchas gracias !! me alegro mucho de que te gustase !
Ver esto es demasiado satisfactorio, ese re embobinado me dejo totalmente loco! Excelente trabajo! :)
Muchas gracias Andres ! me alegro mucho de que te guste , saludos!
At first, it looked impossible indeed! Great work! Wow! for the finished product!
Thanks !!!!
Buen video, Hacia muchos años que no veía bobinar un motor a mano. Excelente trabajo. Un saludo
Muchas gracias Guillermo !!! Un saludo !
Парень знает количество витков, расположение в полюсах, т.д. Работа профессионального обмотчика. Great RESPECT !
Muchas gracias !!
Да, особенно когда лаком с балончика брызгал!!!!!!!!!
Amazing, the amount of craftsmanship and engineering for such an old motor... Thanks for the detailed and well written history. So RARE these daze!
Thank you very much !!!
Exelente maestro no veia un embovinado de stator de motor del a#o 1970 ,,guy dia 2021 lo felicito maestro ,,me remonto casi a mi adolecrncia ,,al 💯 x 💯 ,,,gracias ,,lo saludo de midland texas
Muchas gracias a ti por verlo y comentar !! Me alegra mucho que te guste ! Saludos desde España !!
¡Asombroso, realmente asombroso! Estoy totalmente impresionada con este trabajo. Hay que ser un profesional como la copa de un pino para realizar esta restauración de modo tan impecable. La paciencia y la maestría te hacen merecedor de ser EL MEJOR de entre los mejores. Y es que este tipo de artículos merece la pena conservarlos. Me encanta haber encontrado este canal en español; prueba de que aquí hay estupendos profesionales. Una admiradora total. Suerte con el canal y a seguir así de bien. Saludos desde Córdoba.
Muchas gracias !! Me alegra mucho que te guste el canal !!
This is insane man, others have millions of views for a stupid blade and you just restaurate a whole electric motor, your work is awesome, keep going!
Muchas gracias !! Seguiré adelante !!
Вот это и есть настоящее восстановление старых вещей! Большинство "реставраторов" на ютубе ограничиваются чистой и покраской, а замену обмоток на столетнем электродвигателе делают единицы.
Спасибо !!
Извините, а лаком и запечь, так не делали? Просто вопрос.
@@clashroyaleminecraft9066 No se horneo , si se puso barniz , feliz 2021 !!
@@myrelics1 процесс называется спеканием, т.к. применяется лак, который кристализуется при высоких температурах в специальной печи.
@@igorovcharov7424 vale , ahora entiendo , gracias
We all envy you! The winding of the stator, is something that I wouldn't trust myself to do (even with the degree I have). I put down my degrees to you. Thank you. You are a treasure!
gracias a ti por verlo y comentar !! y por tus títulos 🤣
Sin lugar a duda lo artesanal convertido en restauración, te quedó perfecto
És um verdadeiro artista! parabéns! Resgatou a história desse motor guerreiro dando oportunidade de conhecermos como era antes essa relíquia e obra de arte! Sua pessoa é singularmente incrível! habilidosa! com grande inteligência! Ganhou meu like milhões de vezes se fosse possível! Sucesso em sua vida sempre!
Muito obrigado Roberto!!
Uma restauração de engenharia que eu sem dúvida considero uma obra de arte. Maravilhoso o trabalho.
Muito obrigado !!!
Es un chingon un video 100 por ciento valido media hora en mi vida que vale la pena..
Gracias !!
El ver este video me devuelve el alma,felicitaciones
Muchas gracias Gilbert !!!