KZhead
Автокөліктер мен көлік құралдары

How To Completely Correct Contaminated and Scratched Paint With A Two Step Polish! - Chemical Guys

Chemical Guys
2022 ж. 28 Мау.
625 306 Рет қаралды
Жүктеу

Restore brilliance and shine by following along with today's video! Using a dual action polisher cuts polishing time and saves effort. The TORQ10FX gives the perfect speed, control, and accuracy to perform at the highest level on any job. Use lower speeds to spread wax or sealant with an even coat, or higher speed settings to remove defects like swirls and scratches. Speed and perfection was our goal in developing C4, the evolutionary compound capable of precision paint correction and perfection. Rapid results in less time in a compound that is effortlessly capable of removing scratches and swirls, sanding marks, scratches, acid rain etching, and severe swirls and holograms means this is your new go-to compound whether you have a DA or rotary polisher, or you’re working by hand. C4 is developed for fast cutting paint correction without long work times and is designed and developed for tremendous results in the shortest time possible.
With P4, speed is of the essence and long work times are not required, so you can get incredible results in the shortest time possible. When you’re looking for a truly perfect finish with deep gloss, P4 polish technology effortlessly produces flawless results with your DA or rotary polisher. The versatile polish is capable of correcting 2000 grit and finer sanding marks without dusting or leaving behind residue, making this polish extremely easy to use and work with.
- OG Clay Bar
bit.ly/453nABH
- Clay Luber
bit.ly/3MxdoKE
- C4 Clear Cut Correction Compound
bit.ly/3WaB2j1
- P4 Precision Paint Polish
bit.ly/3IinRXH
- TORQ 10FX DA Polisher
bit.ly/41Hj8ph
- Black Light Glaze
bit.ly/4531FdV
- Jet Seal
bit.ly/42EVISY
- Lucent Spray Shine
bit.ly/3IgDtet
- Polishing Pad Conditioner
bit.ly/3MwDLjK
--------------------------------------
● Find a Detail Garage Near You: www.chemicalguys.com/storeloc...
● Website: www.ChemicalGuys.com
● Subscribe to our channel: kzhead.info...
● Like Us on Facebook: / chemicalguysmfgco
● Follow us on Instagram: / chemicalguys
● Follow us on TikTok: / chemicalguys
#chemicalguys #detailing #polish

Пікірлер

  • Paint Correction Like A Pro! - C4 Clear Cut Correction Compound: bit.ly/3pJUB5I - P4 Precision Polish: bit.ly/432QsrN - Black Light Glaze: bit.ly/3MxiPcv - JetSeal Protectant: bit.ly/3IbOUnl

    @ChemicalGuys@ChemicalGuys Жыл бұрын

    • Yep 👍

      @TruckXaleRepair@TruckXaleRepair8 ай бұрын

    • Uii

      @shanehaynes9021@shanehaynes902128 күн бұрын

  • I love the fact that you guys did an older vehicle with dents, paint failing and showed real results! Been working on my 66' candy apple red Galaxy using Chemical Bros products including your buffer 👍👍

    @hankschrader149@hankschrader1498 ай бұрын

    • Thanks so much for tuning in!

      @ChemicalGuys@ChemicalGuys8 ай бұрын

    • Agreed, not everyone has a Ferrari, Porsche, or any other super car to apply these techniques to.

      @flytheater@flytheater5 ай бұрын

  • I'm a mobile detailer, and I absolutely love Chemical Guys product, I cannot say that I've disliked any! These videos were really helpful for me to start this business, thank you Chemical Guys

    @francjac4546@francjac4546Ай бұрын

    • Glad to have you as part of the Chemical Guys family!!

      @ChemicalGuys@ChemicalGuysАй бұрын

  • I appreciate the Chemical Guys team taking the time to make these tutorials for us.

    @davidmccallum3688@davidmccallum3688 Жыл бұрын

    • Hi David! Thanks so much for the awesome feedback!!

      @ChemicalGuys@ChemicalGuys Жыл бұрын

  • I used the C4 and P4 on my wife’s SUV…..WOW what a difference, great products guys! Keep them coming

    @itzdiff8555@itzdiff85554 ай бұрын

  • As always, it's good to see this stuff in action and that it's possible for everyone to do it if they want to. Great products and excellent results!

    @FordF4NN@FordF4NN Жыл бұрын

    • 💪 Thanks for watching!

      @ChemicalGuys@ChemicalGuys Жыл бұрын

  • Thank you, Joey! The list of compounds and pads are especially helpful. Not having the power-washing tools, your micro-fiber hand-glove and EcoWash followed by Luber and ClayBar before the cutting and polishing and protecting has been my favorite. Your process sure is impressive! Thanks for great products and demonstrations!

    @stephensynergy@stephensynergy Жыл бұрын

  • Paint correction is one of the sickest projects for sure.

    @P4SDetails@P4SDetails Жыл бұрын

    • Always satisfying! Thanks for being a part of the Chemical Guys family

      @ChemicalGuys@ChemicalGuys Жыл бұрын

  • Absolutely best car care video I have seen, am ordering all products now, fantastic, thank you so much gang.

    @stevegatting5237@stevegatting5237Ай бұрын

    • Thanks so much for being part of the Chemical Guys family!

      @ChemicalGuys@ChemicalGuysАй бұрын

  • I appreciate these “walkthrough” style videos.. thank you

    @randomdudehere4828@randomdudehere482811 ай бұрын

    • 😀😀

      @ChemicalGuys@ChemicalGuys11 ай бұрын

  • Glad Joey is still rockin it. Been watching his vids for years.

    @jeremiahmoss6015@jeremiahmoss601510 ай бұрын

    • 👍👍

      @ChemicalGuys@ChemicalGuys10 ай бұрын

  • I don’t care what they say about you guy’s, i love your products and my clients love how the car’s look so it’s a win, win. I have your entire collection of products, bucket, rags everything.

    @bryanmonserrate8288@bryanmonserrate8288 Жыл бұрын

    • Thanks so much for being part of the Chemical Guys family!

      @ChemicalGuys@ChemicalGuys Жыл бұрын

  • Thanks for showing how this can be done on a realistic car for most people. As much as we'd all like we cant be driving around in a Porsche 911 and sometimes gotta make do with a honda civic. But this shows yiu can still look good even if your car is a little beat up!

    @justcusimazn@justcusimazn4 ай бұрын

  • Y’all’s product is amazing I just did headlight restoration and I’m highly satisfied as ur customer and u highly satisfied my customer 💯💯💯💯‼️‼️‼️‼️‼️‼️

    @alexzuniga6329@alexzuniga63296 ай бұрын

    • Glad to have you as part of the Chemical Guys family!!

      @ChemicalGuys@ChemicalGuys6 ай бұрын

  • Dat background music got me bumpin my head... Dope video

    @paulpereza3845@paulpereza3845 Жыл бұрын

    • Glad you enjoyed the video!

      @ChemicalGuys@ChemicalGuys Жыл бұрын

  • Awesome 👏 job. Real educational

    @mantovauniepeters1927@mantovauniepeters1927 Жыл бұрын

    • Glad you enjoyed the video!!

      @ChemicalGuys@ChemicalGuys Жыл бұрын

  • I've got to say thank you to all the viewers for asking such great questions! You've helped me immensely!😊

    @MrBikedrummer@MrBikedrummer Жыл бұрын

    • Happy detailing!

      @ChemicalGuys@ChemicalGuys Жыл бұрын

  • yeah first timer with a DA even a Harbor Freight model your combos do work. I started with the V34/V38 now I will try this combo C4/P4. Thanks for the tips!!

    @k4x4map46@k4x4map46 Жыл бұрын

    • Let me know which combo you like better! For black paint

      @texasbrotherhood3930@texasbrotherhood3930 Жыл бұрын

    • @@texasbrotherhood3930 Copy that!! I been a lil lazy so I'll get on it and let ya know soon as possible!! Coincidentally I'm working on black paint as well...I didn't have the pad treatment so that'll be worthy to note as well.

      @k4x4map46@k4x4map46 Жыл бұрын

    • Enjoy your detailing products!

      @ChemicalGuys@ChemicalGuys Жыл бұрын

  • One more detail, in CA it's a bit hot and doing this stuff with car, which is really heated from the direct sun, this is not good for the health of the bodypart (If you want to ever do this and the hot weather is expected, do it in the shadow, or early at the day or in the evening). On the other hand I appreciate the job the guys have done.

    @kukkaties@kukkaties8 ай бұрын

  • Amazing as always ❤️

    @mmortada1978@mmortada1978 Жыл бұрын

    • Thanks so much for the awesome feedback!

      @ChemicalGuys@ChemicalGuys Жыл бұрын

  • I was thinking that maybe your products could be color matched with the pad colors! Thank you for the video!

    @SteveFloresCoach@SteveFloresCoach Жыл бұрын

    • Happy detailing!

      @ChemicalGuys@ChemicalGuys Жыл бұрын

  • Love your products!!

    @parmanndhensaw6845@parmanndhensaw6845 Жыл бұрын

    • Thank you for being part of the Chemical Guys family!

      @ChemicalGuys@ChemicalGuys Жыл бұрын

  • Great job Joey 💪💯

    @osanshouo1684@osanshouo1684 Жыл бұрын

    • Happy detailing!

      @ChemicalGuys@ChemicalGuys Жыл бұрын

  • Great video. My car has a similar issue as this one just above the windshield on the roof. Is there anything you recommend to fix that? I don't think its bare paint yet but can it be saved??

    @conradborba7856@conradborba78566 ай бұрын

  • Super helpful explanation

    @bboylorettoEight08@bboylorettoEight08 Жыл бұрын

    • Glad it was helpful!

      @ChemicalGuys@ChemicalGuys Жыл бұрын

  • Hi! what to do after polishing if i want to add some spray ceramic? do i rinse the car first with water to remove excess polish? or is it okay to just spray on top of polish? thanks!!

    @GgG-71494@GgG-714949 ай бұрын

  • Great video. Thanks

    @justinmieirs3501@justinmieirs3501 Жыл бұрын

    • Thank you for watching!

      @ChemicalGuys@ChemicalGuys Жыл бұрын

  • very informative. Thank you sir

    @abdulmajeed1173@abdulmajeed1173 Жыл бұрын

    • 😃

      @ChemicalGuys@ChemicalGuys Жыл бұрын

  • Can I use black light glaze right after washing my car with black light soap? Or do I need to need to use C4 and P4 in order to use black light glaze? The paint of my car is not really bad, btw.

    @victorf.4599@victorf.4599 Жыл бұрын

  • Bravo great work

    @alexhendricks9280@alexhendricks9280Ай бұрын

    • 👍

      @ChemicalGuys@ChemicalGuysАй бұрын

  • What happens do the roof? Do you still go over it? Do you ignore and go around the part that’s failing but still do the rest of the roof? Do you still Apply wax the whole roof after you polish it including the failing paint Even tho you didn’t polish?

    @raidersperez1278@raidersperez12787 ай бұрын

  • Do you have a video detailing steps for windshield/Windows? My windshield is having this tiny spot which looks like dust but won't clean with cleaners. Thanks

    @mokhan0982@mokhan0982Ай бұрын

  • Hey quick question, how can I get a dried up silly putty or silly string color, off-white car and dried up when the sun and left a marker type stain on it is there anything I can use that you recommend?

    @hitman3867@hitman38679 ай бұрын

  • Do you have a video of polishing a fresh painted car with some dust in the paint? If not what polish would recommend for wetsand

    @openshot@openshot8 ай бұрын

  • I purchased a polishing starter kit that includes V32, V34, V36 and V38. I am planning to perform "paint correction" on my old Mercedes that has mild and heavy scratches, swirl marks and everything else that you would expect on a well-loved 23 year old car. I will clay bar first. Should I begin with V34? Can I go down to V32 if I don't see the results expected with V34? Also, what is the difference between the V series products and the C and P series products?

    @raredan60@raredan603 ай бұрын

  • wow fabulous demo & tutorial -- am learnng so much about your products & process ... btw ..... what is the music @ 15:50? .. it is absolutly fantastic!! ... as ever .... thanks so very much for all your hard work and sharing your expertise with us ... Iʻve subscribed and will be following many more of your videos ;)

    @jmdfineart@jmdfineart Жыл бұрын

    • Thanks so much for tuning in and for subscribing!

      @ChemicalGuys@ChemicalGuys Жыл бұрын

  • How much pressure do you use when doing your passes with C4?

    @GarbageMan994@GarbageMan9949 ай бұрын

  • What a fantastic video.

    @irhm8640@irhm8640 Жыл бұрын

    • Glad you enjoyed it!

      @ChemicalGuys@ChemicalGuys Жыл бұрын

  • Hi there! Just to be sure-I can use clay or another decontamination liquid? Make any sense use dec liquid after clay? just to be sure is all gone? Greetings from UK, Tom

    @tenzin044@tenzin0442 ай бұрын

  • Will these polishing pads fit on an m18 milwaukee polisher? I have mo access to an AC outlet

    @chrispy4u2@chrispy4u211 ай бұрын

  • How does the C4 compound compare to the V32 & V34 compounds? Similarly, when to use P4 rather than V36/V38? Maybe I haven’t spent long enough studying Chemical Guy’s products, but it’s not intuitive as to which product is best for my needs.

    @anyfeckinusername@anyfeckinusername Жыл бұрын

    • Hi Ted! C4 and P4 are a great combination to cut down on time and effort while still achieving professional results. C4 is comparable to V34 and P4 starts out aggressive then refines to a comparable V38.

      @ChemicalGuys@ChemicalGuys Жыл бұрын

  • At 12:40 are you increasing the speed of the polisher?

    @RachaelMaresh@RachaelMaresh10 ай бұрын

  • Im about to do this process on my 2014 bmw, but its supposed to rain that night. Will it be okay to take out into the weather or does it need time to cure?

    @antilag8837@antilag88375 ай бұрын

  • I see your two Smarts behind you! What do you use on their soft plastic panels to keep them looking good?

    @clwest3538@clwest3538 Жыл бұрын

    • Hey! Check out HydroShield to lock in an OEM finish while repelling harsh elements. www.chemicalguys.com/hydroshield-vinyl-rubber-plastic-ceramic-shine-coating/TVD11616.html?gtmListValue=Internal%20Search

      @ChemicalGuys@ChemicalGuys Жыл бұрын

  • Chemical Guys, I've been looking for a source of information, or a "guide", so to speak. But I'm not sure what I'm looking for even exists. I've heard different professional detailers say different cars require different products inside and out. Do you provide such a guide in which you recommend certain products of yours for that specific vehicle? For example, let's say I have a 2008 Dodge "whatever whatever", I look that up in the guide, and it tells me which of your products are safe on the interior, seats, carpets, outside, wheels, etc. Thank you for your response!

    @slomotion1028@slomotion10289 ай бұрын

  • Hey CG how often do you spray pad conditioner onto a pad? Every time you add compound/polish or just one to three sprays at the beginning.

    @alexvasilchuk3601@alexvasilchuk3601 Жыл бұрын

    • Hey! Use Pad Conditioner for the first few panels then as needed.

      @ChemicalGuys@ChemicalGuys Жыл бұрын

  • I'm hoping I get to try the clay bar from your product line

    @MichaelFG@MichaelFG Жыл бұрын

    • Happy detailing!!

      @ChemicalGuys@ChemicalGuys Жыл бұрын

  • How would you compare Jet Seal vs Butter wax after using the black light glaze? I have butter wax but should I consider jet seal instead?

    @HoltistheGOAT@HoltistheGOAT Жыл бұрын

    • Hi there! JetSeal will provide a longer lasting barrier of protection whereas Butter Wet Wax adds a warm gloss. Use them in tandem for the best of both.

      @ChemicalGuys@ChemicalGuys Жыл бұрын

    • ​@ChemicalGuys will black light glaze offer a barrier of protection? I ask because I used butter wax and then the black light glaze recently on my black truck to prepare for winter

      @HoltistheGOAT@HoltistheGOAT7 ай бұрын

  • After putting compound, when i try to remove it with cloth the compound is just not getting off easy untill i put pressure on cloth with fingers

    @muhammadsameerdero1830@muhammadsameerdero1830 Жыл бұрын

  • QUESTION : If car has a lot of scratches and some are quite deep so you need to paint them..but you also are planning to do full paint correction.. should we: 1. We first sort those deep scratches (preparation,sanding, painting, polishing), then do the full paint correction of whole car... 2. We do painting of deep scratches mid way of full paint correction... (after wash...iron and tar decontamination and clay bar decontamination) 3. We do all the steps of paint correction and before applying ceramic coating we focus on sorting those big deep scratches

    @VBOJAN86@VBOJAN869 ай бұрын

  • do i need to polish and seal if i’m going to wax after?

    @enriquemos6778@enriquemos67789 ай бұрын

  • I don't know how many people are going to spring for a $500 Polish job on an $800 car but nice work.

    @2.Plus.2.Equals.5@2.Plus.2.Equals.5Ай бұрын

    • Those are the best cars to do it on. I got a E36 conv for 2k. And that baby is beautiful and I just did this job to it and got some BBS on it. Summer bout to be great.

      @voiceofalabama@voiceofalabamaАй бұрын

  • How often should you clean the pad during the compound and polishing stage?

    @DavidRuiz-nb9fh@DavidRuiz-nb9fh Жыл бұрын

    • Yes

      @pullingthestrings5233@pullingthestrings5233 Жыл бұрын

    • I've heard after every panel or some people like to clean it after every little section on the one panel

      @hoodiealan9518@hoodiealan9518 Жыл бұрын

    • Hi David! It is normal to clean the pad several times during the job depending on paint condition and products used.

      @ChemicalGuys@ChemicalGuys Жыл бұрын

  • Helpful

    @traceyclifford7489@traceyclifford7489 Жыл бұрын

    • Glad the video was helpful!

      @ChemicalGuys@ChemicalGuys Жыл бұрын

  • How often are we able to reuse the clay bar? Are we supposed to throw away the piece we just used? If not, how do we clean it?

    @lovelykkim9643@lovelykkim9643 Жыл бұрын

    • Hey! Roll and knead the clay bar until a clean side can no longer be found at which point the bar should be replaced.

      @ChemicalGuys@ChemicalGuys Жыл бұрын

  • Any chance you have a video on how to correct the scratches on and behind door handles?

    @Rooki3_@Rooki3_ Жыл бұрын

    • Hey! Check out this video. kzhead.info/sun/p7qnf7J9fWlrZIk/bejne.html

      @ChemicalGuys@ChemicalGuys Жыл бұрын

    • @@ChemicalGuys thank you!!

      @Rooki3_@Rooki3_ Жыл бұрын

  • Can you use C4 and P4 with a buffering pad, or do you need a rotary polisher?

    @blackfoxmp5@blackfoxmp5 Жыл бұрын

    • C4 and P4 can be applied by machine using a rotary or dual action or by hand.

      @ChemicalGuys@ChemicalGuys Жыл бұрын

  • So say i wanted to add ceramic coating to my car. Would that theoretically be applied after I have polished with the C4/P4 combo? Or would I still need to apply black light and then ceramic coating?

    @gabrielquinones-medina2707@gabrielquinones-medina2707 Жыл бұрын

    • Hi Gabriel! That's right, ceramic should be applied to a bare surface that has been polished.

      @ChemicalGuys@ChemicalGuys Жыл бұрын

  • Any advice on back and shoulder pains while polishing ?

    @Martiizzer@Martiizzer Жыл бұрын

    • Hi there! Reduce fatigue by using less pressure on the machine and finding the most comfortable position.

      @ChemicalGuys@ChemicalGuys Жыл бұрын

  • great video! quick question, from a noobie. What these same techniques be safe on a classic car, like a 1975 Corvette Stringray? As I understand, they didn't have clear coat back then, its just enamel.

    @josephciaccio8211@josephciaccio8211 Жыл бұрын

    • Yes, absolutely!

      @ChemicalGuys@ChemicalGuys Жыл бұрын

    • @@ChemicalGuys thank you! you're giving me the courage to try!

      @josephciaccio8211@josephciaccio8211 Жыл бұрын

  • Awesome as always 😎

    @honourvirtue3820@honourvirtue3820 Жыл бұрын

    • Thank you! Cheers!

      @ChemicalGuys@ChemicalGuys Жыл бұрын

  • You can also use the cigarette cellophane test. Great way to test to see if you need to clay more.

    @vermontvermont9292@vermontvermont929211 ай бұрын

    • Happy detailing!

      @ChemicalGuys@ChemicalGuys10 ай бұрын

  • Hi, excellent video, did you keep the speed at 1 the entire time?

    @johnnysmith5961@johnnysmith59618 ай бұрын

    • Hi there! Use the highest speed setting on your dual action to break down compound and polish.

      @ChemicalGuys@ChemicalGuys8 ай бұрын

  • can you use Black Light Glaze on Carbon Force ceramic coating?

    @pandaaazy5062@pandaaazy5062 Жыл бұрын

    • Hey! Yes, Carbon Force can be layered with your favorite glaze, sealant, and wax.

      @ChemicalGuys@ChemicalGuys Жыл бұрын

  • How long does one pass take to complete? What is your hand speed rate? Also what speed settings did you use for c4 and p4 passes?

    @chriswaidelich6640@chriswaidelich6640 Жыл бұрын

    • Hi there! Work in a 2 foot by 2 foot section, moving 1 inch per second.

      @ChemicalGuys@ChemicalGuys Жыл бұрын

    • What about speed setting for polisher? Still 1 setting?

      @adamcurrie3026@adamcurrie3026 Жыл бұрын

    • @@adamcurrie3026no. You’ll never get any results using 1. Most use setting 5 but you can play around and see what you like best.

      @ohboy2592@ohboy2592 Жыл бұрын

    • @@adamcurrie3026 The product bottles will give recommendations for pad speed etc

      @defritzel@defritzel Жыл бұрын

  • Can you go over blacklight glaze with the hydro slick or whatever the hydro ceramic coating is

    @brother_maleik@brother_maleik11 ай бұрын

    • Hey! It is best to apply HydroSlick to a bare surface and then it can be layered with your favorite glaze, sealant and/or wax.

      @ChemicalGuys@ChemicalGuys11 ай бұрын

    • @@ChemicalGuys ok thought so, cuz in the video you said you'll apply blacklight and then the sealant, which I was confused about I thought it should be the other way around

      @brother_maleik@brother_maleik11 ай бұрын

  • What speed settings did you use? Speed setting 1 to spread out c4/p4 but did you increase the speed to compound or did you keep at speed setting 1?

    @philliph259@philliph259Ай бұрын

    • Hey! Yes, when using a DA/Random Orbital use the lowest speed setting to spread the product and then use the highest speed setting to diminish the compound/polish.

      @ChemicalGuys@ChemicalGuysАй бұрын

  • What backing plate is that? I don’t see it listed on site. Doesn’t look like the ones I have on my torq polishers.

    @joshreece5803@joshreece5803 Жыл бұрын

    • Hi Josh! This is the original 5 inch backing plate.

      @ChemicalGuys@ChemicalGuys Жыл бұрын

  • I have to C4 cut correction I don’t have the polishing, so can I use the V 32 polish or is it the 38 the lower the number the finer it is right ?

    @richardPalmisano@richardPalmisano2 ай бұрын

    • Hey! Correct, the V-Line is variety of compounds and polish with the most aggressive being V32 and least aggressive being V38.

      @ChemicalGuys@ChemicalGuys2 ай бұрын

  • Do you prefer using c4 and p4 over your v-line polishes ? Which would give better results ?

    @anthonymorales1178@anthonymorales1178 Жыл бұрын

    • Hey Anthony! C4 and P4 are great for moderate to light imperfections or when you are short on time. Use the V-Line for multi-step corrections of heavy swirls and scratches.

      @ChemicalGuys@ChemicalGuys Жыл бұрын

    • @@ChemicalGuys what would be the steps using the v-line ?

      @anthonymorales1178@anthonymorales1178 Жыл бұрын

    • Thanks for your question! Helped me!

      @MrBikedrummer@MrBikedrummer Жыл бұрын

  • Quick question, when you showed Black Light Glaze it said it was a sealant. So why are you applying an extra sealant(Jet Seal) if Black Light is a glaze and sealant??

    @juanvel389@juanvel389 Жыл бұрын

    • Hi there! Black Light is primarily a glaze that has some sealant properties, follow up with Jet Seal to add a long lasting, durable layer of protection.

      @ChemicalGuys@ChemicalGuys Жыл бұрын

    • @@ChemicalGuys can i put a paste wax then a liquid ceramic coat ? Or only one ty for your time

      @Brandon-yj4pw@Brandon-yj4pw Жыл бұрын

    • ​@Brandon135 no a sealant needs to bond direct to the Clear coat to protect correctly and last. After you seal u can top coat with wax

      @davidsteadyjr8243@davidsteadyjr8243 Жыл бұрын

  • Welcome to this guy because he is cool 🤙

    @TruckXaleRepair@TruckXaleRepair8 ай бұрын

    • 🤩🤩

      @ChemicalGuys@ChemicalGuys8 ай бұрын

  • What is your recommendation for washing your car after apply Black Light and Jet Seal? Hand wash? Car wash? And would you need to reply after washing? Thanks for the great vid!

    @CaptianFlan@CaptianFlan Жыл бұрын

    • Hey! Maintain your coatings by using HydroSuds as your maintenance wash. Black Light will last a few months whereas JetSeal lasts up to one year.

      @ChemicalGuys@ChemicalGuys Жыл бұрын

  • What speed volume do you finish polishing with white pad?? Ijust ordered pads n compoud from chemical guys thanks...

    @hernang7509@hernang75099 күн бұрын

    • Keen to understand this too

      @Npg2@Npg27 күн бұрын

  • Mình là người miền tây và đã định cư ở Hoa Kỳ được 35 năm vô tình nghe được bài nhạc nầy mình đã không kiềm được cảm súc hay quá ca từ mọc mạc chân và phương tuyệt vời quá A Páo đẹp quê hương Việt Nam ❤

    @vinhlong7114@vinhlong71146 ай бұрын

  • I’m all set to polish tomorrow but forgot to buy your polish conditioner. Could I simple use the clay lubber water?

    @Frankie5Angles@Frankie5Angles Жыл бұрын

    • Hi Frank! It is safe to use clean water to prime the pad but this should be a temporary solution.

      @ChemicalGuys@ChemicalGuys Жыл бұрын

    • @@ChemicalGuys thanks for the quick response guys!

      @Frankie5Angles@Frankie5Angles Жыл бұрын

    • Happy detailing!

      @ChemicalGuys@ChemicalGuys Жыл бұрын

  • Does it work the same to just rinse off the clay lubricant with a pressure washer instead of wiping it off?

    @raysilva12@raysilva12 Жыл бұрын

    • Absolutely!!

      @ChemicalGuys@ChemicalGuys Жыл бұрын

  • So you could do a 2-step with C4/P4 but what about V34/V38? What would be the major differences here? If you started with V34 you could also do a 3-step with V34/V36/V38.

    @samdickinson8212@samdickinson8212 Жыл бұрын

    • My question exactly

      @18monthplan@18monthplan4 ай бұрын

  • Thats the nicest set of 5 spoke 7th gen wheels left on earth

    @xXsc3n1cXx@xXsc3n1cXx2 ай бұрын

    • 😆😆

      @ChemicalGuys@ChemicalGuys2 ай бұрын

  • Which would be best to use the C4&P4 or the V line products?

    @stephanietorres6835@stephanietorres6835 Жыл бұрын

    • Hey Stephanie! Start with a test spot to determine the correct pad and chemical combination. Use a White Pad with P4, if more abrasives are needed use an Orange Hex-Logic Pad and C4.

      @ChemicalGuys@ChemicalGuys Жыл бұрын

  • Can I do all these steps but replace the spray shine with Hydro Slick?

    @stevencastaneda4808@stevencastaneda4808 Жыл бұрын

    • You can mix and match almost anything! If you are going to apply Hydro Slick or any other ceramic, however, we recommend applying it directly after the polish, and letting it cure before applying any other waxes, glazes or sealants on top.

      @ChemicalGuys@ChemicalGuys Жыл бұрын

  • Can i put a wax after paint correction snd then liquid ceramic or no ?

    @Brandon-yj4pw@Brandon-yj4pw Жыл бұрын

    • Hello! After paint correction lock in your hard work by applying ceramic and then it can be layered with your favorite glaze, sealant and wax.

      @ChemicalGuys@ChemicalGuys Жыл бұрын

  • "Hey I'm looking for product recommendations to keep my car's paint protected and avoid stripping it during regular washes. After doing this process, Any suggestions for gentle yet effective car wash products?"

    @PalmiraBarbecue@PalmiraBarbecue10 ай бұрын

  • Does it have to be the entire car or can I just buff and polish say where the door trims use to be? I removed my door trim, left behind lighter shade of actual color and some minor scratches and swirls kinda…doi have to do my entire car or just those spots ?

    @santiagovalenzuela7454@santiagovalenzuela7454 Жыл бұрын

    • Hey! It is possible to spot polish only the affected areas however it may be necessary to blend the surrounding area to prevent a noticeable difference.

      @ChemicalGuys@ChemicalGuys Жыл бұрын

  • Is the c4 compound better than the V line compound you guys offer?

    @corrywilliams1290@corrywilliams12905 ай бұрын

    • Hi there! The combination of C4 and P4 is perfect for vehicles that don't require multi-step paint corrections or when you're short on time.

      @ChemicalGuys@ChemicalGuys5 ай бұрын

  • Could you of also used v32 or v34 instead? or are the results better with C4 and P4?

    @tmxx3328@tmxx3328 Жыл бұрын

    • Hey! For most aggressive cutting, use V34 or even V32 to remove deep imperfections.

      @ChemicalGuys@ChemicalGuys Жыл бұрын

    • Man you guys are on top of it, very thankful for your videos I was able to find one to get an understanding of your different polishes and compounds also v line products. Now I definitely see why v32 or 34 would not be too smart to use on here😂

      @tmxx3328@tmxx3328 Жыл бұрын

  • If I plant to use Black Luminous Glow Infusion, when should I use it? After black light glaze? And the jet seal, before or after using Black Luminous Glow Infusion?

    @victorf.4599@victorf.4599 Жыл бұрын

    • Hey Victor! Apply Black Luminous Glow Wax after JetSeal and Black Light.

      @ChemicalGuys@ChemicalGuys Жыл бұрын

    • @@ChemicalGuys thank you!

      @victorf.4599@victorf.4599 Жыл бұрын

    • @@ChemicalGuys and then can I still use banana spray wax as a last step after using those products?

      @victorf.4599@victorf.4599 Жыл бұрын

  • I don't have the luxury of a car bay or garage. What tips could you give ? Thanks

    @Ghost_8082@Ghost_808211 ай бұрын

  • when i polished my car with VSS and the TorqX, there was still paint scratches after, i’ve watched several videos of your guys tutorials, i don’t know what i’m doing wrong, how can you help

    @shanesackett7597@shanesackett7597 Жыл бұрын

    • Hi there! It may be necessary to use more abrasives for deep scratches and swirls.

      @ChemicalGuys@ChemicalGuys Жыл бұрын

    • Search orange peel paint, there's a guy sanding with an air sander he's the best explaining how to sand without the wet sand.

      @angelproductionsvip@angelproductionsvip Жыл бұрын

  • Hey guys, am I able to use a ceramic coating product after using ALL the products you guys used in THIS video?

    @rosendorendonjr@rosendorendonjr Жыл бұрын

    • Hey! Apply ceramic after the paint correction stage, then it can be layered with glaze, sealant and wax.

      @ChemicalGuys@ChemicalGuys Жыл бұрын

  • Rather than the spray shine could I use an actual ceramic coating? I'm trying to figure out when the best time to ceramic coat would be. After the sealant I imagine?

    @vermontvermont9292@vermontvermont929211 ай бұрын

    • ceramic coatings always goes before anything else. that’s the most durable, longest lasting protection, which is why you want it under everything such as sealants, waxes, etc

      @joey4261@joey426110 ай бұрын

    • @@joey4261 I did. Almost a month ago now. Did a light machine buff since my car barely needed it. Obviously a wash first, clay, and IPA in-between everything. You know what I mean. Then once the paint was super clean and ready I applied the ceramic coating. Waited a week until I washed it again. Since then I use a quality spray ceramic detailer after my washes.

      @vermontvermont9292@vermontvermont929210 ай бұрын

  • Can the P4 be used in combination with other glazes and sealants?

    @corrywilliams1290@corrywilliams12905 ай бұрын

    • Absolutely!!

      @ChemicalGuys@ChemicalGuys5 ай бұрын

  • Hi! What speed setting are you using for C4 and P4 after spreading on speed 1?

    @leetran04@leetran04 Жыл бұрын

    • Hey! When using a DA, use the highest speed setting to diminish the compound and polish.

      @ChemicalGuys@ChemicalGuys Жыл бұрын

    • @@ChemicalGuys hey Bud what will it be on a rotary 1-6 I just can't seem to find my speed I start getting friction immediately using that same C4 solution what ami doi g wrong?

      @jamiemorales2022@jamiemorales2022 Жыл бұрын

  • what speed on the 10FX for the cutting with C4? 25 / 35?

    @Daali@Daali Жыл бұрын

    • For spreading, use the lowest speed setting. For cutting, it depends on the level of scratches, but most times you can get away with the highest speed setting for the fastest cut!

      @ChemicalGuys@ChemicalGuys Жыл бұрын

    • @@ChemicalGuys cool deal. was looking for this answer versus posting a similiar question...

      @k4x4map46@k4x4map46 Жыл бұрын

  • When polishing you should do the least aggressive step first to avoid an extra step if possible

    @JesusPerez-ik3jd@JesusPerez-ik3jd Жыл бұрын

    • Hi there! Yes, begin with a test spot to determine what pad and chemical combination would work best starting with the least aggressive approach.

      @ChemicalGuys@ChemicalGuys Жыл бұрын

    • Thanks for that comment!

      @MrBikedrummer@MrBikedrummer Жыл бұрын

  • Do you need the pad spray or does any detail spray work?

    @agoodbogey@agoodbogey Жыл бұрын

    • Hi there! In a pinch you can use your favorite quick detail spray to moisten the pad however using Polishing Pad Conditioner is the best solution for pad longevity.

      @ChemicalGuys@ChemicalGuys Жыл бұрын

    • @@ChemicalGuys thank you! i have the pad cleaner spray and quick detail but not the pad conditioner.

      @agoodbogey@agoodbogey Жыл бұрын

  • how long does it usually take to wash, dry, clay bar, polish & sealant the car?

    @juthanemanase8818@juthanemanase8818 Жыл бұрын

    • Hey! Thanks so much for tuning in. A detail can take anywhere from 3 to 8 hours depending on the condition of the paintwork.

      @ChemicalGuys@ChemicalGuys Жыл бұрын

    • Long enough so CG have time to make another video with all new products so you have to start over. 😅

      @MrBikedrummer@MrBikedrummer Жыл бұрын

  • I have a question can you claybar with pinstripes over paint?

    @andrewsulfaro3468@andrewsulfaro3468Ай бұрын

    • Absolutely!

      @ChemicalGuys@ChemicalGuysАй бұрын

  • Can you do paint correction outside I don’t have anywhere that fits my truck I’m assuming I can..?

    @kristiangarnica6210@kristiangarnica6210 Жыл бұрын

    • Hi there! It is best to polish indoors or shaded area when the surface is cool to the touch.

      @ChemicalGuys@ChemicalGuys Жыл бұрын

  • Can I use this WHOLE LAYOUT to correct a ‘16 civic with parking lot scratches from carts and such also automated car wash damage to clear coat???

    @Earnyourday@Earnyourday Жыл бұрын

    • Absolutely!

      @ChemicalGuys@ChemicalGuys Жыл бұрын
KZhead