GTI TRANSMISSION REPAIR DIFF BEARING AND OUTPUT SHAFT BEARINGS
2015 ж. 30 Нау.
245 872 Рет қаралды
Hi this is a transmission that had a loose differential and I replaced the bearings on the diff and the output shaft.
Hi this is a transmission that had a loose differential and I replaced the bearings on the diff and the output shaft.
Awesome video still helping in 2024
Thank you so much for this video. It was incredibly helpful for me. I have 2 trans' 1 broke where the drivers axle smacked it. The other has a busted bell. Now I can make one from two. Your detailed teardown was very helpful. Don't worry about the haters, most of them are desk racers anyway.
Très bonne vidéo. Merci pour prendre le temps à le faire.
Very good video! Thank you!
Thanks for sharing. Great tutorial !
Where are you bro? Lol I would come to you. I really like all the details you check . Says a lot to me about you being a mechanic. Take pride in your work. My bearings need to be replaced. I need a rebuilt transmission. The bearing on my driver side axle is whining when I go through my gears. I was thinking get the clutch replaced to and everyone says my clutch is good and just change the bearings on the driver side axle . I put new axles in and it’s still whining. When giving it gas. Honestly I would rather bring it to you lol
Super Great video very helpful ty alot
To get the bearingraces out you can weld around the entire race, that will shrink the whole race together so you can pry it out easely.
Christian, it seems to me that you are a model teacher / explainer. At each step, you explained exactly what I wanted to know next, making it an incredible learning experience for me. No waffle. No nonsense about what a gearbox is and why you might want to fix one. Instead, straight down to business, with a step by step account of what's involved. I want most KZhead videos to be like this - it would be much better use of my time. I hope you are well and went on to do many more good things.
Cool video!
Thx so much, really appreciate your video, I'm really used with 02m trans and was very disappointed because I was not able to split the cases, shitty hidden bolt!!! Thx again, good job!
hi. a great video, what would you have to do to make the gearbox run backwards? i want to put a engine and box in a vw t2 and have 5 gears- i know can put the engine and box in turned around but it wont be pretty thanks
Could you provide some guidance? 2003 Jetta 1.8L turbo 5 spd manual Wolfsburg. Replaced lower control rods without disconnecting drive shafts. Somehow the flange shaft on the passenger side pulled out of the housing by about an inch. I plan to pull the drive shaft and see if the center bolt has backed out. Do you have any advice?
great video. I have a passat mk4 manual transmission 5 speed similar to this one, how much is the cost of this service, my car something wont go in 3rd or 4th gear but not all the time.
My friend I was searching about front differential video and I find a whole experience it is the best!!!! I have skoda rapid tdi 1.6 and trying to find how to change valvoline and differencial oil and what type should be!!! Anybody knows 😷
Hi, maybe I missed in video, was there any shims under bearing race ? Have you measured preload on bearings ? I am rebuilding transmission (different one) and there are some strange things going on there....
Recently got a vw jetta from coworker for $100 intended to swap my vr into. Long story short she sold it cheap thinking transmission was cracked. I looked in thought it was a slave cylinder since they're plastic and swapped in New one. Drove car to work this morning and saw trail of fluid into spot I parked at. It looks like I have fluid coming out of the top of the transmission. It looks like a inspection hole but I haven't had time to really look. Is this a sign of a bad input shaft seal? I am stumped but want to figure this out asap
Your video was very helpful. I was hoping to take the bell housing section off only for a repair. But after I decided to take it all apart I realized that wasn't going to happen. The bearing punched threw the casting where the 4 nuts are. I'm going to weld the piece back on and will probably need to remachine the bottom of the bore. I'm assuming zero preload and zero end play on the bearings.
Hi there
Hi where do you find the part numbers of each gear?