Lexus Toyota VSC / Trac Warning Light FIX
2019 ж. 7 Там.
406 603 Рет қаралды
How to fix reset your Check Engine, VSC, Trac off warning light.
Lexus, Toyota and many other makes/models.
Follow the easy steps in this video to do it yourself and not pay dealerships $$$$ for something so simple and free!
Make sure to SUBSCRIBE to catch all the latest content! / @flipitgarage
Follow on Instagram @themvgarage
If you have any questions comment below! Please consider “Subscribing” to catch all the latest content! 🤙🏻 Note: If you have a check engine light on with the VSC watch this video: kzhead.info/sun/nLCrn9CgiaRvn6M/bejne.html
MV Garage hello I have a 2007 is250 my check engine light svc and traction control light is on does this method work with my vehicle?
Do you put the paper clip while the car is running?
lenny hernandez If you have a check engine light on then you need to fix that first and then the VSC will turn off.
Bie Ngosa You should install the clip with the car off. That’s what I would recommend. But should work either way since the plug has constant power.
Will this work for a 2008 gs350?
Just to let everyone know, i tried this method on my LS460 (2007) and it worked! Saved me thousands!! You earned a Sub my friend.
Appreciate the feedback! 🤙🏽
I was just gonna ask about the same car. I just got the starter changed on my LS460 (08) and to my surprise I have these lights on the dash that weren’t there before. Did you use the same pins as mentioned in the video?
Thanks so much my guy I just got my alignment done on my 2009 Toyota Matrix XRS and every time I tried to ride my car the light would light up and it was driving me crazy because before the light would light up the car would not let me accelerate passing certain mph so now it’s fixed. Thanks again 💯⚡️
Your welcome! Glad to help ! Thanks for sharing makes my day! 🤙🏻
Hi, i recently replaced both of the front cv axles on my car. These axles were replaced while there was a check engine light on the car along with trac and vsc flashing as well. The car became a pain to drive after the axles replacement. Car drives fine straight but is hard to turn. It's almost as if there is no power going to the wheels when i turn the wheel and give it gas. The car did drive fine before the axles were replaced, and at the time, the check engine light and vsc were both on. Problems started after the axle replacement. Should i have done the check engine light fix first and then the axles??
Thank you so much..just got an alignment and when I turned my car on this popped up..I appreciate the help brotha
Matthew Trujillo Your welcome! Glad to help!
Thanks so much! Can’t believe this worked. I’ve been trying to get rid of this for over a year
Awesome! Your welcome. Glad to help! 🤙🏼
I usually never write a comment and to be honest didn't think it would work but it did ! Thanks for saving me trip to the dealership and $ !
Oscar Mendoza well glad I’m your first comment! Glad it worked out and you got it fixed! Your welcome 😊
That's really helpful I have that same car right now and I have that exact problem I'm gonna try this .. Thank you so much for the tip I'll let you know if it worked for me.
Not a problem! Happy to help! Let me know how it goes! ;)
2007 LS460 - fix worked after tire shop had repaired a flat. Thank you!
Nice! Happy to Help! 🤙🏽
They asked me to pay $700 today for this lol thank you for this video
Positive Vibes lol! Crazy stealerships. Your welcome!
I have a 2002 Lexus RX 300. I had blinking VSC & ABS Lights flashing and nothing else worked in getting them reset. I did the paper clip action, as stated in this video, and both reset and stopped blinking. Thanks for the info.
John I Thompson Your welcome! Glad it helped!
Your video has the most concise information for this problem across YT. It should have gotten more hits. I am certainly going to spread your video around as it has the simplest steps and most helpful fix most of us laymen needed.
Thank you! Really appreciate the feedback and your support!! 🤙🏽
Great video. I have rx330 and for 3 yrs never knew the issue. Thought it had something to do with the gas cap. Changed caps and still was on. All along just needed a paper clip and your video. Thanks
Haha! Happy to help! Thanks for the great feedback. It’s appreciated 🤙🏽
I just saw a video where a guy said cleaning the gas cap fixed the issue but that didn’t make sense to my. How would a loose gas cap affect the traction control? 🤷🏾♂️
@@inaedemarughu8275 The “guy” that made that video clearly has no idea how to diagnose a car lol. Definitely not true.
Hi MV Garage, great video. Do you know how to do the Engine check light and VSC light in together. I cleaned the MAF sensor and throttle body but power on with MAF sensor disconnected.
John CW Chan Hi ! And thanks ! Usually if there is a check engine light that always triggers the VSC light as well. You would need to get the code scanned for the check engine light it could be one of a hundred different issues. You can get it scanned for free at any auto zone. Let me know the code and I can try to help. Thanks.
Much Appreciated will try scan codes then. Cheers!
2007 Lexus GS AWD This worked perfectly!!! Thanks soooo much!!!! (I noticed the light came on after I put a heavy generator in the trunk. This must have thrown something off. Now no lights 😊)
Appreciate the feedback! Happy to help 🤙🏽
I just meet on this condition. I'll try tomorrow morning. Thanks.
Great video, works for me and hope the warning lights stay off.
Did this with my GX470 and it worked flawlessly. Thank you so much I wasn’t finding any answers on how to fix it
Kathan Tomlin Nice! No problem. Glad it worked out for you! 😊
If I did it on my GX470 and it didn't go away does it mean there is a particular issue with VSC?
@@TheLANDSQUID hey bro this just happened to my gx470 today along with not being able to shift out of park when I start the car I have to override the shift lock release to get it into drive. There was four lights that came on the abs vsc off vsc trac and anti skid. But they came on intermittently and did not stay on continuously for the entire trip just as I’m pulling off out of park and a few more times throughout a road trip but there is nothing wrong with my car it never effected performance. Did your lights ever back come back on after you reset if with with paper clip trick? And also were the lights coming up intermittently for you or did they stay on until you reset it?
@@slickenzmcglickenz4671 same thing just happened to my 2006 is350
@@slickenzmcglickenz4671 you probably gonna need to replace your oxigen sensors soon, hope this help...if that's the case order them on Amazon, it will save you lots of money!!!
Thank you .. ‘this video was very helpful it works on my RX330...
No problem! Glad I was able to help! 😊
😂
Will this work for my 2006 Toyota 4runner? I had seen other videos using the paper clip but for the 4runner the other videos showed that one paper clip is in the 3rd hole on the top left and the other paper clip is in the 4th hole bottom right. I tried it and it didn't work, I had to touch them 4 times and turn the vehicle off and turn back on again and touch the clips together for 20 sec and then turn it off and on again. It was a workout. Please tell me I can follow your steps. Thanks.
Terrance Gamble I’ve never tried it on the 4Runner but it should be the same procedure since I did this on a 2006 Lexus. Also on a 2018 Toyota. And it was the same. But I can’t say for sure on your vehicle. Won’t hurt to try. Let me know how it goes.
Thx so much for posting this video! You saved me so much time after doing a tie rod replacement!
Happy to help! Appreciate the feedback!
Just done this today, worked a treat thank you.
keith hilton Your welcome ! Glad to help!
Thanks so much was so stressed about it and it worked!
How do I get rid of battery light as it shows and I changed battery and alternator a year ago after alternator damage. Car charges though
I actually tried it today, and guess what.. it f worked! The light didn’t come back, so most likely it’s gone. Now when winter hits hard, then my anti-spin should work I guess. A huge ‘thank you’ to you 🙏🏻🙃
Glad it worked for you! And your welcome happy to help 🤙🏽
@@FlipITGarage Man, I always pray for you because of this video lol. The light never came back, and my AWD was functioning properly. I have a question, when I accelerate, it smells like rotten eggs. What do you think it could be?
@@mesopotamia59 appreciate that! Thank you. Happy to help! 🤙🏼 that smell during hard acceleration is sulfur from the catalytic converter. Could be starting to break down but I wouldn’t worry about it unless it triggers a check engine light.
Im going to try this over the weekend wish me luck...
Thanks! Saved in my favourites for future reference.
Mark2790 Your welcome !
Thank you soooooo much!!!! Worked perfectly! I am so grateful for your generous sharing of this knowledge 🙏
Your welcome! Happy to help! 😊
Just got these lights on this morning, and just to make sure you have you gas cap right and my steering wheel 🛞 was originally off a few inches since my last mechanic replaced the starter sure enough it finally worked !!! Thanks so much !!! 🎉
Glad it worked out for you! Appreciate the feedback! 🤙🏽
After so many research, finally you showed me the right way to fix it. Thanks ❤
Happy to help! 🤙🏽
So what happens when you use the diagnostic tool to read the car does the code still show ?
Thank you so much! Worked like a charm!
You're welcome!
So I have a 06’ IS350. Has been scanned as a wheel speed sensor about a year ago, it only came on in the rain. I got a wheel alignment and now it’s on every single time I drive the car, doesn’t cause any issues, just annoying to look at. Would this work or would I need a nee sensor do you think?
I have Lexus 2008 is 250 same problem for this lights on I need to do just like this what you doing or so let me know please 🙏
Hi. Yes if you have the VSC light on this procedure will work to reset it on your vehicle.
Thanks a lot, It works on my 2007 Lexus 350is
Your welcome! Glad to help ! :)
@@FlipITGarage after drive it for 10 miles, then it comes back again!
Samson Wang Then is wasn’t just triggered. You may have a bad wheel speed sensor or something else. You’ll need to get it scanned. Let me know what faults you get I will try to help.
Will this work ina 2012 Tacoma
804peel SS. Never tried it on that truck. But if should work.
Hi, i have IS350 with check AWD system showing and as C1298 code. Both the connection and the wires are in good condition but the light still showing. How can you help out?
2007 GX 470 it’s the 4th from the right. Works like a charm. Thanks!
Update... worked but then the light came back on. Tried the paper clip trick, lights flashed but then didn’t turn off. What’s next??? I just got new tires and rims
Sound like you may have an issue with one of the speed sensors. Did you ever figure it out?
@@Justin-ge6fu hey bro this just happened to my gx470 today along with not being able to shift out of park when I start the car I have to override the shift lock release to get it into drive. There was four lights that came on the abs vsc off vsc trac and anti skid. But they came on intermittently and did not stay on continuously for the entire trip just as I’m pulling off out of park and a few more times throughout a road trip but there is nothing wrong with my car it never effected performance. Did your lights ever back come back on after you reset if with with paper clip trick? And also were the lights coming up intermittently for you or did they stay on until you reset it?
Thank you. God bless you
Same to you!
Thanks so much... I'm going to try this... I just bought a used GS 300... I love this car but the VSC light just came on.
No problem! Glad to help. Let me know if you have any issues 🤙🏼
Did it work for you? I have a 2006 Lexus gs300 same issue
@@ueray4 This video was made on a 2006 GS300. As long as it’s just the VSC light it’ll work.
@@ueray4 it worked but it was a temporary fix.. so I bought a code reader and I reset the alarm that way.... The alarm will come back on after about 10 miles of driving... Doesn't seem to have an effect on the car at all... Love my ride
Great video. I have GS300. What triggered the VSC light for you?
Appreciate it! On this car it was triggered by the speed sensor getting bumped when changing wheels. It is also a 2006 GS300.
@my garage will this work for 1998 Lexus GS300?
I get the tracking control light with the check engine light will this work the same way? have a 2010 rx350
Check out this video to reset those lights: kzhead.info/sun/nLCrn9CgiaRvn6M/bejne.html
Thank God for His wisdom upon your life . May the Lord bless you. It works on my Lexus 2006 RX 400h . Thank so much.
Glad to help! Thank you for the feedback! 👌🏼
having the same issue. lexus 400h. is the line up the same i noticed the plug is 90degrees rotated
@@sadrirammal275 did it work?
Does the VSC light being on have anything to do with the continuous beeping noise?
Myron Feggins Jr Usually doesn’t cause a beeping noise, well atleast it didn’t on my GS.
That was the door being opened thats why it was beeping
Worked perfectly on my 2007 ES350! Thanks for this!🤙🏼
Glad to hear! Happy to help 🤙🏽
Worked on my isF. Thank you very much. Deleted an o2 sensor code after replacing but the vsc stayed. This took it right off. Aggravating the cel triggers this and doesn't let me go into 1st or have traction
Glad it worked out for you! 🤙🏽
Great video, hope it works on mine!
I hope so too! Thanks for the feedback!
Bro I recently purchased a 2007 Lexus GS 350 has a few issues and your videos are everything I need 🙌 couldn’t ask for better help!!!
Appreciate the comment! Happy to help ! 🤙🏽
Is this actually true?
I just purchased 07 gs350 and it has check vsc
Wondering if this will work on a 2008 LS 460. Having a similar issue with all the brake and VSC lights. Any insight?
As long as the check engine light isn’t on this procedure should work for you.
Ahhhh man, what happens if the check engine light IS on???
Hi I changed the clock spring and steering angle sensor (I broke old by mistake) job was easy turned on now have trc and vsc lights. I have scan tool so reset steering angle sensor and cleared codes. U0126 keeps coming back. Lost communication with SAS control module. I tried all of these hacks also the one where you touch the cables 4 times within 8 seconds into the reset mode. No joy I still have the lights. Any tips or is my new (used of ebay) unit bad is my next thinking. Thanks in advance also checked every fuse. I did the job with battery disconnected and also have left disconnected over night to see if that sorts it. Still no. Also test drive to see if it re learns but no.
Henry Phillips Hi! Sounds like you covered all the basics. I would suspect a bad unit if everything is hooked up properly. I would swap it with another one to confirm. Also check all your connections.
@@FlipITGarage Fixed it! I was rite: The new used part on ebay was to blame! I only broke my clock spring not the SAS so worth a try I put my old SAS on the new clock spring and it worked first time! Re calibrated. No codes to clear because it was all happy. This all started because I was aligning the steering wheel to the rack for the correct amount if turns each way. Now I have done that job also needs major wheel alignment it was loose and way out! I hoped fixing this would also solve the serious brake judder but unfortunately it hasn't. This judder causes bad wheel bearings and drop links after 6 months it's so bad! New brakes all round also every bush and ball joint is good. New tyres and wheel balance. Drive / prop shafts good. On a Lexus is250. Any suggestions 🤔
Thanks ... Work like Charm
You're welcome! Glad it worked out for you!
Man you are the sh@t!!! I wish I would have seen this last year before I changed a sensor. A year later the light is back, hopefully it will stay away.
jayfaris112 Lol! Thanks. Glad to help!
What was the issue?
@MV will this work on an is250 too?
MrClopse Yes same procedure.
Hey man, I have a 2007 lexus is250 and my VSC and check engine lights both came on after replacing front right tire, I tried everything in your video, I connected the paperclip as mentioned and let the car run through the cycle you showed, after that, my car is currently driving fine but the lights are still on, how do I get them to go off?
Sometimes you have to repeat the procedure. Unless its a hard default then you need to address the issue.
Hi did you manage to find out the problem for your lexus is250? i have the same problem with my 06 is250
Love this sorted my speedo and tachometer aswell much love 👍🏼👍🏼😁
Red or Dead Glad to help!
@@FlipITGarage saved me buying a scanner 👍🏼👍🏼😁
After a mental breakdown
😂🤣. Exactly my feelings too!
Would this work for the 2009 Lexus RX-350? I am having the VSC Light and check engine light showing time to time on the dashboard recently for no reason. Thank you so much
The VSC is on because the check engine light. You can clear them by disconnecting the negative battery terminal for 10 mins. But if the lights comes back you will need to get it scanned to see the issue.
Easiest method I’ve seen yet. Fantastic in fact. It PLEASE!!!.....I BEG of you!!!......LOSE the opening whatever you call that aggressive sounding assault on my ears pounding electronic slop that I guess is supposed to be..........MUSIC?????
Brian James Glad to help! Lol yea I’ll work on that intro 😂
One thing to add. On mine I actually had to disconnect the battery first wait 15-20 minutes for charge to die and then reconnect the battery and do this procedure. Cleared the code.
Thanks for the tips for anyone that it’s not working for, worth a try. 🤙🏼
I have the same light and same car year and model (06 gs300). But my car's traction control doesn't work because of the light. I want it to work more than to erase it. Would my traction control work again if I do what you did? Thanks
Do you have the check engine light on as well ?
I have an 08 lexus is350, I place the paper clip in the 4th hole top in bottom and I did not go into vsc mode. Can you make a recommendation?
S Chance It should definitely work for your vehicle. Did you have the power on ? And compare with the video to make sure you were in the correct spot on the connector.
Dope video quick and to the point! Unfortunately I have an 07 and it set up differently (sad face)
Appreciate the feedback! 🤙🏽
Would this work on the Lexus is350?.. I dont want to accidentally short anything out if the connector pins are not the same
If it’s just the VSC light on this procedure will be the same on the IS.
I have 08 Lexus Es 350, I change my winter tires and put summers on . After few hours this light pops up. Should I try this magic on ES 350 as well ?
Sounds like the same issue I had. Yes should be the same procedure for your ES. Won’t hurt to try. Let me know how it goes !
Does this procedure apply to the 02 RX300,also ? Thanks
mckoy lach Yes same procedure on the RX300.
MV Garage thank you very helpful
Does trick apply to the "06" is250 model? Thanks for sharing.
Yes, this would work on the 06 but only if the VSC light is on without the check engine light.
@@FlipITGarage ok, both lights are on so I won't do the paperclip trick. I'll try the battery disconnect. Thank you for the reply.
This works like a charm. thanks a lot.
Happy to help! 🤙🏽
Hi MV, I got code P0A80 - Replace Hybrid Battery pack on my lexus 2006 Rx400 H. history- I did not drive for 1 month. So when it did not start got battery replaced by AAA and now I have check engine, red triangle 🔺 with exclamation, ABS on. Any suggestions what could I do to fix...
Haven't worked on many hybrids. There may be a reset procedure that needs to be preformed when installing new batteries on hybrids.
I have the same problem now, but my car is IS220d, will this procedure work please as my car is Manual not auto?
Ola Dapson definitely should be the same procedure for your car. Won’t hurt to try. What year is it ?
Hi my lights on my lexus is250 recently came on vsc light and check light also trac light. the code for the the check light was p2757 which was the transmission after replacing the transmission twice the light came right back after about 20 to 80 mile twice this happen so i know its not the transmission whats the next step i should take could it be my computer
Dang Vue Hi possible causes for that code. Dirty transmission fluid Faulty line pressure solenoid valve SLU Line pressure solenoid valve SLU harness is open or shorted Line pressure solenoid valve SLU circuit poor electrical connection Torque converter clutch Valve body is blocked If you checked all those and replaced what you needed to did you clear the code ? Reset it with a scan tool or disconnect the negative battery terminal for 10 minutes. The VSC light is only on because the check engine light.
Thank you a million times. How did you figure this out?
Your welcome! Happy to help. Learned this trick from a buddy that worked at Lexus.
My 05 ES 330 has VSC and trac off lights on and has a code P0442 also. It’s evap system small leak. Is this a separate issue ?
This is if you only have the VSC light. See this video to reset both: kzhead.info/sun/nLCrn9CgiaRvn6M/bejne.html
Sounds like maybe a bad gas cap or it wasnt screwed on good. Especially if you haven't had any work done to it recently.
Thank you bro 🙏
Hi. Will this work on Lexus 2007 RX 400h? Hybrid version. Looks like previous owner had the tires changed and this happened but I bought the car so I want to fix this. Appreciate any help given…
Hi! Is it just the VSC light on ? Or is a check engine light on as well?
I have the same car and it is the VSC indication, along with ABS, Traction, E brake, and Brake warning lights
Thanks for the informative video! What was the significance of parking of a level surface and with the steering wheel straight while fixing the check VSC light?
Nhat Tran Your welcome! I just had it parked in the garage. Doesn’t have to be perfectly flat but recommended to be as close as possible.
@@FlipITGarage What is the significance of that? What does that have to do with the VSC problem?
Nhat Tran The procedure also recalibrates the steering angles. So it best to do it so it doesn’t throw the steering angle sensors off.
Nhat Tran use some common sense
@@visionnumber7988 OK smart ass!
will this work on toyota mark x 300g 2006
lawrence wong It’s possible! We don’t have those cars in the US. Let me know if it does. Won’t hurt to try.
Will this work on 2017 Acura ilx?
I Play 2 Win Truth Seeker Never tried it on an Acura. I would think it would be a different procedure but I’m not sure, it might.
My car battery died there was some corrosion so we cleaned that up and when I jumped my battery the vsc light came on never came on before will this work for that or should I take to a garage (07 Toyota Camry xle)
Is it just the VSC light ? Or do you have a check engine light on with it?
My check vsc just came on while driving to work. Will this troubleshoot work for a 08' gs350?
I was driving normally and it appeared, did i find a way to fix it?
Yes, itll be the same procedure.
Have the exact same car thanks for the help!
Happy to help! Great cars!
I will try this on my 2007 IS250. The VSC, trac control engine light just came up after a couple of minutes passing through some rough bumps. I hope it helps
Keep me posted!
Did it work? I just got this car from my father in law and it has this issue.
@@GenericEricGames As long as it’s just the VSC light on it should work. Won’t hurt the car to try.
Mine is a toyota venza 2011. Would the same process work for it?
Should be the same procedure. Won’t hurt the car to try it.
Do u just use one paperclip in both holes linked the whole time
chris cash Yep just one paper clip to connect both side.
Will this work for VGRS system light?
Haven’t tried it to fix that issue but it won’t hurt the car to try it.
Question here putting the paper clip in there will not affect the car in any way? Like the ecu or other electrical component?
Nope, won’t hurt the car putting it in the correct slots.
My 2007 gs430 had the diagnostic say the right front wheel speed sensor fault. On checking the connector I noticed it has some vertigris on the brass pins and in the receiving sockets of the plug. Cleaning those terminals cleared the fault.
Nice! Glad you found it and figured it out. Easy fix 🤙🏽
Recently got a 08 is250, i have an intermittent issue with the vsc light, it comes on after driving a distance over 30km. Though if I switch the car off and on, the vsc light goes off. On the obd scanner it says foreign object interference or something similar on the left back wheel. I bought a new wheel speed sensor but when I installed it the vsc light came on immediately when driving. Would the new sensor be faulty or should I try this and see if it works?
It may be an issue with the wheel bearing itself that the speed sensor uses to read the data. The code was for a wheel speed sensor and you change the sensor correct ? I would lean towards faulty wheel bearing.
Hello sir my Lexus sc 430 2002 model gear indicator in display and reverse light not working and when I shift s gear to while you slowdown the vehicle it gives jerk plz let me know the cause ND solution
Convertible also not working I recently changed engine after that this all problem came
Sounds like you have multiple issues. That would need to be checked in a shop. Could be mechanical or a computer issue.
hi I bought a lexus rx400ah it shows me vsc system and hybryd system on board I can't accelerate it harder to leave the place the electric batteries don't move I think they are discharged the car has been parked for a long time
Will it work for lexus rx 400h? Mine has lights on and a beep alarm.😢
If you don’t have a check engine light on it should work. Won’t hurt to try.
Hey Man! just bought a beautiful 2007 is250 one owner. 167k miles Check engine, VSC and traction control light came up, I used a snap on OBD reader and codes P0894 and P2714 were shown. I watched a lot of videos and read a lot about this and it seems to affect a lot of lexus owners and seems to have multiple solutions. How will you approach this? I am very tempted to try the paper clip in the obd since I used that with a corolla and solve the problem. the car drives fine with no issues
The VSC light in your situation is on because the check engine light is on. They go on together. I would start by getting the car scanned for codes and go from there.
got an 07 250 my self and they just came on after weeks of not having it. it came on once when i messed up my maf sensor reconnected and fixed it but seems to not be the issue now. did the paper clip method work?
Would this work on my 2006 IS 350??
Meredith Fuentes should be the same procedure as I was working on an 06.
MV Garage. I asked you yesterday about this working on my 2006 4runner and I was reading some of the other questions and your replies it won't work if the engine light also comes on. Mines does and the code I got was P0430 -Generic Catalyst System Efficiency below Threshold Bank 2. Thanks again.
Terrance Gamble yea if the check engine light is on that is why your VSC light is on too. Need to fix that first then the light will go off.
@@FlipITGarage the engine light isn't on all the time. When I clear the codes the engine light also goes off. its like the engine light comes on and the other two comes on behind it and then I clear the codes again.
I tried this on my 2008 RX 400h and which was giving me DIAG VSC 43,45,62,63. After the reset I'm can't seem to clear 45? Any suggestions? I pulled the front wheel speed sensors and cleaned them, but they looked good. Also tried pulling the battery cable, but not change. No CEL. Just VSC.
45 is Acceleration Sensor Output Malfunction. You may need to do a zero point calibration to see if it goes away. If this method didn’t clear it you may need to do it with Techstream computer software. Or could just be the sensor needs replacing.
@@FlipITGarage That was it. I had to do the zero point calibration and it went away. So far so good! I just got the Techstream cable and software and took some time to figure it out.
@@dslemaire Glad you got it worked out! Must of been frustrating. Let me know if you need help with anything else 🤙🏽
I own 08' IS250 recently ran into a potholes and my VSC, check engine light came on. I'm going to use this procedure and see if the problem goes away. Wish me luck!!
PullMeSoftly44 Hopefully it works out for you. But just know whenever a check engine light comes on the VSC light comes on with it. I would look into the check engine light first. More than likely if you reset the check engine light the VSC light will go off.
@@FlipITGarage I tried your method several times hopping that it'll work but failed. So, I tried another method by disconnecting both terminal from the battery and wait several minutes before connecting them back an start the car, that finally solved my problem. The VSC and Chk Engine light went away.. Strange thing!! Thanks for the advice 👍
PullMeSoftly44 Yep. Disconnecting the battery will reset the check engine light. So the VSC light was on because the check engine light. If it does come back on you will need to get the check engine light scanned to see what the problem is. Hopefully it stays off!
Will it work for a 06 lexus IS250 AWD?
Should be the same procedure. Won’t hurt the car to try.
Hi .. How about LS 430 is it the same?
Should be the same procedure. Won’t hurt to try.
Will this work for a RX400h lexus 2008
Aniale Yang should be the same procedure. Most Lexus’s in this year range are the same. Won’t hurt to try.
@@FlipITGarage didnt work my rx400h
Would it work on a 2015 Lexus is250 fsport
Should be the same procedure. Won’t hurt to try.
Thanks so much I fixed the problem easy
Happy to help!!
Hi, my Lexus GS300 2006, very often show the sign of brake systems failure + check engine and VSC, three at the same time. Went to garage at least 9 times, none of those mechanics can fix it. They replace all 4 ignition coils, one set of spark plugs and one set of exhaust spark plugs, and two days later, these three hell signs come up again, I feel hopeless to get rid off these. Hopefully you have some great tips on it. Thank you
vanda Sir. If you can provide me with the codes you get I can try to help. Thanks.
Did you ever figure this out, I’ve read a gas cap, I’ve also read the wheel speed sensor replacement didn’t even work and new tone ring didn’t work
Are these the same spots to put the pin in for a 2005 lexus rx330?
Should be the same procedure. Won’t hurt the car to try.