KZhead
Тәжірибелік нұсқаулар және стиль

How to Use a Diamond Core Drill - The Secret To Making Big Holes

The DIY Guy
2023 ж. 14 Сәу.
489 015 Рет қаралды
Жүктеу

Today i will be showing you how to use a diamond core drill bit and how you can make a big hole in a wall. Common jobs such as tumble dryer ducts and bathroom extractor fan installations all require this method. I will be showing you the tips and tricks that make the job easy! If you like the content leave a like and please subscribe for more content like this as I've got a lot more to come and there will be something that will help you out.
⚪ Buy The Tools Needed Below
🌟 Diamond Core Bit Set - amzn.to/43ecVmC
🌟 SDS Drill - amzn.to/3ZOnZEr
🌟 Tracer Pencil - amzn.to/3WVwdJG
🛒 My Shop -www.amazon.co.uk/shop/thediyguy
► BECOME A MEMBER OF THE DIY CLUB Click! 👇🏼
/ thediyguy1
► Get FULL access to the Discord Group and other perks!
Follow me on Instagram 👉 the_diy_guy_youtube
Thanks for watching The DIY Guy. My mission is to bring you the best Tips, Tutorials and Tools to help you learn and save money.
Please be advised that this is only a guide which is intended for informational, educational and entertainment purposes and The DIY Guy cannot accept responsibility for any work undertaken. Be safe and have fun! The Amazon links above are affiliate links and as an Amazon Associate I earn from qualifying purchases. I may earn a small commission if you purchase via the recommended links, however this will not cost you any extra.

Пікірлер

  • One little tip that I use to ensure you don't get plaster blow out on the inside is to use the core bit on the inside to just cut through that first half inch or so of plaster. Then move to the outside to cut the hole. The pilot hole will ensure that the two cuts line up perfectly, and as you have already cut through the plaster on the inside you don't get it blowing out as the core goes through. Sure, it does make a little dust on the inside but worth it to keep the plaster in one piece. 👍🏼

    @stephenspiceley3082@stephenspiceley3082 Жыл бұрын

    • Thanks for sharing 😀

      @TheDIYGuy1@TheDIYGuy1 Жыл бұрын

    • In your dreams mate

      @alemgas@alemgas Жыл бұрын

    • @@alemgas What is in his dreams?

      @thechumpsbeendumped.7797@thechumpsbeendumped.7797 Жыл бұрын

    • For pros, Makita do a dust extraction accessory for their diamond core drills - very expensive and heavy duty. As heavy duty DiYer, I do what you do

      @cuebj@cuebj9 ай бұрын

    • @@cuebj Potential cheaper solution? Henry + bag. Henry likes to eat all things, and rolls down stairs well, and are still pretty cheap. Mines 25yrs old and for the last 7 has been sucking up everything from masses of brick dust to lose cold ashes around the fire. Remarkable machines, especially the older ones.

      @Nine-Signs@Nine-Signs7 ай бұрын

  • You sir are a Godsend. Instructions clear and concise. That is a job I have dreaded but you have given me the confidence to do it myself. Many thanks.

    @formicapple2@formicapple2 Жыл бұрын

  • Top tips as usual, and I love how clean your safety goggles always are! Look forward to the renovations👍

    @jamesduffy5019@jamesduffy5019 Жыл бұрын

    • Thanks. Those are new ones sent to me from Unilite. Great glasses so far.

      @TheDIYGuy1@TheDIYGuy1 Жыл бұрын

    • @@TheDIYGuy1 Now do hearing protection and a dust mask. Wear all your PPE and set a good example

      @bobbymac2911@bobbymac29114 ай бұрын

  • Great video, I did an extractor fan recently using these bits 👍🏻

    @DjGiluk@DjGiluk Жыл бұрын

  • Thank you very much Your videos is very good Everything is well explained Please do more videos like this 👍

    @ibrahimeryuruk4728@ibrahimeryuruk47289 ай бұрын

  • Someone below mentioned it, kickback control, but didn’t quite get to the optimal solution. Left or Right there is always a drill-handle orientation that will let you catch the kickback, which is the only way the clutch will ever engage. For the hole here, rotate the whole drill clockwise 90, then release the handle and rotate that another 90 so it is pointing straight up. Now you can engage the drill with your right hand and the handle is such that kickback with be straight into your palm, allowing the clutch to trigger rather than having it rip away from your hand. Nice video!

    @jasonmcbride88@jasonmcbride888 ай бұрын

  • You can avoid any brake out on the inside by drilling a little that side first.

    @martinw245@martinw245 Жыл бұрын

    • That’s certainly another option 👍

      @TheDIYGuy1@TheDIYGuy1 Жыл бұрын

  • Good explanation! A little advice: in the future, try to move the handle in 90 degrees to right or left. In case of stuck or something you will control the drill much easier Good luck!

    @curentarul@curentarul5 күн бұрын

  • This is a very helpful video!

    @nikond90@nikond908 ай бұрын

    • Glad you think so!

      @TheDIYGuy1@TheDIYGuy18 ай бұрын

  • great video - any tips to stop core sticking to abour - tried copper grease already thanks

    @czeital@czeital9 ай бұрын

  • Perfect video! In Sweden we often use 125mm vent ducts. What dimension do you recommend for the hole?

    @johanlind3002@johanlind30028 ай бұрын

  • Great video i am drilling through a wall this week for extractor fan great tip drill out pilot hole first from inside and then drill from outside due to dust 👍👏

    @martinkiely3147@martinkiely3147 Жыл бұрын

    • Glad it was a help

      @TheDIYGuy1@TheDIYGuy1 Жыл бұрын

  • As always a great informative video 👍🙏

    @michaelshaw8656@michaelshaw8656 Жыл бұрын

    • Cheers bud 😀

      @TheDIYGuy1@TheDIYGuy1 Жыл бұрын

  • I can tell you from experience that the core bit / drive shaft you are using will bind together after heavy use. It is then virtually impossible to separate the shaft from the bit and that means you cannot change bits thereafter. Before use I would recommend making and breaking the shaft/bit joint and also using copper grease or similar to make subsequent release of the joint more likely. I was drilling foundation wall that consisted of heavy-duty concrete blocks laid on their sides. The second point I would make is that the stub shaft being used will not get you through such long traverses. Eastablish whether you need a shaft extension before committing to task as separate purchase of long shaft is expensive. If these extensions binds and won’t release you will have an even greater problem to solve. I eventually resorted to stitch drilling after first creating the first short penetration using diamond core. That worked well and was faster but not a neat finish on the exit side of the hole.

    @johnashton4086@johnashton40865 ай бұрын

  • Great tip about running the pilot bit all the way through and core drilling back in from the outside. Wish I had thought of that doing all my room vents 🤣🤣

    @tm2204@tm2204 Жыл бұрын

    • Glad to help!

      @TheDIYGuy1@TheDIYGuy1 Жыл бұрын

  • Excellent presentation as always!

    @Kidglove57@Kidglove57 Жыл бұрын

    • Glad you like the video 👍

      @TheDIYGuy1@TheDIYGuy1 Жыл бұрын

  • Nice work, thankyou ..well done.

    @thebrooklyngardenclub225@thebrooklyngardenclub225 Жыл бұрын

  • Informative video. Wondering if this would work with the Hilti TE 50-AVR.

    @rfrancislau@rfrancislau7 ай бұрын

  • It’s a good idea to put a slight rise, (out to in) on the hole, not level when to be used for vapour exhaust. Any moisture left in the ducting when machine stops will drain to the outside of the wall.

    @Pelt101@Pelt101 Жыл бұрын

    • Nice tip, not something I’ve ever done.

      @TheDIYGuy1@TheDIYGuy1 Жыл бұрын

    • Came here to say the same thing. Probably precautionary more than anything but it can’t hurt!

      @matthewsaunby9056@matthewsaunby9056 Жыл бұрын

    • Absolutely! Very important that condensation finds its way out and not in!

      @paulchatterton1@paulchatterton1 Жыл бұрын

    • But then if you're drilling through for something like a humidistat, the fan doesn't sit flush to the wall because the hole is on the wonk.

      @gaurasrspublishing@gaurasrspublishing9 ай бұрын

  • Excellent video and edit. look forward to the renovation series.

    @deanwellerassociates@deanwellerassociates Жыл бұрын

    • Thanks. I’m working on it. Currently I’m working on the edit for episode 1

      @TheDIYGuy1@TheDIYGuy1 Жыл бұрын

  • may as well get a condensing dryer as in a couple years we will see another video of you bricking it back up.

    @chrisjinks5414@chrisjinks5414 Жыл бұрын

    • I’ve an old boiler flue hole to brick up if it’s something you want to see 😂

      @TheDIYGuy1@TheDIYGuy1 Жыл бұрын

  • Beautiful job

    @MegaLove85@MegaLove859 ай бұрын

    • Thank you! Cheers!

      @TheDIYGuy1@TheDIYGuy19 ай бұрын

  • For the pilot hole bit (8 mm) does that bit need to be diamond tip also? Or can I use the pilot bit that comes with the core bit to drill the pilot hole?

    @user-kk8md7jr1n@user-kk8md7jr1n9 ай бұрын

  • Experience is the best teacher You're great

    @oluwordaj1729@oluwordaj1729 Жыл бұрын

    • Glad to have helped. Thanks

      @TheDIYGuy1@TheDIYGuy1 Жыл бұрын

  • Brilliant tip on drilling from inside to out first!

    @superamario6464@superamario6464 Жыл бұрын

    • Glad it was helpful!

      @TheDIYGuy1@TheDIYGuy1 Жыл бұрын

  • When I was drilling through some really dense comcrete using a 4.5” bit, it helped a lot to chisel away the inside core every inch or so

    @goldistocks609@goldistocks6095 ай бұрын

  • Thank soo much freind, i appreciate a lot your advices, i lear lot of things from you , thank again , good luck for futur videos

    @assili_abdellah@assili_abdellah11 ай бұрын

  • Great Job!!

    @yorkrojas1452@yorkrojas1452 Жыл бұрын

  • Great job and great video thanks for sharing with us this appreciations 🇩🇰🙏👍

    @melvis2017@melvis2017 Жыл бұрын

  • Great advice, and great Norfolk accent......"wull done bore keep on a troshin" 👍

    @boyo57@boyo579 ай бұрын

  • Great video !!!!! Looking forward tothe new series .........thanks 😊😊😊😊😊

    @michaelplays2449@michaelplays2449 Жыл бұрын

    • Thanks. Soon, I’m working on the final edit for episode 1 😀

      @TheDIYGuy1@TheDIYGuy1 Жыл бұрын

  • Awesome job 👍🏼

    @h.google@h.googleАй бұрын

  • Excellent video. Thank you.

    @Surbitron9000@Surbitron900014 күн бұрын

  • Lovely video mate

    @HarveyJohnWillmott@HarveyJohnWillmott7 ай бұрын

  • Great tip on the pilot drill

    @philipwilliams8114@philipwilliams811417 күн бұрын

  • Great video! How would you go about enlarging an existing hole to fit a cooker hood that needs a bigger hole?

    @samirguesmia4378@samirguesmia4378Ай бұрын

  • I've saved a few quid having a go myself, which I didn't really have the confidence to do before watching videos like this. Nice one DIY guy, keep them coming!

    @TomBlakey-we8rf@TomBlakey-we8rf7 ай бұрын

    • Glad I could help! Thanks!

      @TheDIYGuy1@TheDIYGuy17 ай бұрын

  • Hello mate whats the best length sds bit for this? I bought 400mm but think 600mm willl be better

    @BS-ix7qp@BS-ix7qp Жыл бұрын

  • Great video. One thing I'd point out in my case - even if it means some vertical ducting inside stay well clear of the DPC. My house sits on a plinth of some sort and if you hit that your hole stops there. Got lucky, but it was close!

    @tomsanders8714@tomsanders8714 Жыл бұрын

    • DPC? Democratic Political Cheat?

      @chipburns4123@chipburns4123 Жыл бұрын

    • Good point. I have exactly that: rectangular duct between wall and dryer, rectangular to round connector to duct in wall. Unexpected benefit is it's more flexible when I've changed position and brand of dryer - just shorten or lengthen the flat duct and change angle from dryer vent to wall vent

      @cuebj@cuebj9 ай бұрын

  • Can you give any tips for enlagering a previous hole?

    @wdy0196@wdy01967 ай бұрын

  • Good tips

    @Hitngan@Hitngan Жыл бұрын

  • spraying water occasionally, helps with dust and provide some cooling to the the core drill.

    @eliadbu@eliadbu Жыл бұрын

  • Would you recommend going from outside then doing the inner wall from inside out over if you had pipes and cables nearby?

    @PhasesOfIronCarbon@PhasesOfIronCarbon5 ай бұрын

  • I really enjoyed the way you explained it. Smart and clean. Only for safety put on a mask too beside the safety glasses. For protecting of all that dust entering to your lungs. If you do this on daily basis it can lead to nasty lung diseases.

    @samansrs6287@samansrs62872 ай бұрын

  • first time here .very informative will be looking out for more of your videos.

    @mykotliazad@mykotliazad Жыл бұрын

    • Awesome, thank you!

      @TheDIYGuy1@TheDIYGuy1 Жыл бұрын

  • great video thanks

    @MalcolmJames-sg3zg@MalcolmJames-sg3zg Жыл бұрын

    • Glad you enjoyed it

      @TheDIYGuy1@TheDIYGuy1 Жыл бұрын

  • is your drill machine rated for 117mm drill ???????

    @the_f0@the_f08 ай бұрын

  • Very helpful video Thankiyou so much very appreciate your help.

    @mohmedsirajkasadiya9367@mohmedsirajkasadiya93676 ай бұрын

    • Glad it was helpful!

      @TheDIYGuy1@TheDIYGuy16 ай бұрын

  • What is a recommended hand drill machine? I am asking about lowest watt machine required for a hole saw bit to drilling in properly?

    @TuhinBhuiyanWebDeveloper@TuhinBhuiyanWebDeveloper5 ай бұрын

  • great video what min wattage drill to use?

    @daifu4427@daifu4427 Жыл бұрын

  • Great video! Thank bro, wish you good health and success always!

    @dailytricks6161@dailytricks6161 Жыл бұрын

    • Thanks a lot you too 👍

      @TheDIYGuy1@TheDIYGuy1 Жыл бұрын

    • @@TheDIYGuy1 have nice day! bro

      @dailytricks6161@dailytricks6161 Жыл бұрын

  • how well does this work in fiberglass reinforced concrete and what happens if you run into rebar?

    @jimkurk5575@jimkurk55752 ай бұрын

  • I'm looking for an SDS drill that can drill big holes. The SDS drill you link to is actually the one I was thinking of getting but everyone says it's not going to be able to cope with core bits over about 20mm and I need a corded drill for anything over this. I notice you use a corded drill in this video, what's my best bet for site and domestic work as I don't really want to have to buy two for the different power ratings? Cheers.

    @42RHD@42RHD4 ай бұрын

  • I've been prevaricating on this one for my cooker hood for months, I'm sure I'll brave up enough to do it eventually - my complexity is timber framed house so i got moisture barrier to deal with also; though I also have only one layer of brick to deal with so swings and roundabouts.

    @streaky81@streaky81 Жыл бұрын

    • Hole saw or pad saw for the timber and plasterboard. The single thickness brick could be done with lots of holes using 6mm or 8mm SDS bit; then tap with small cold chisel. If you do hire or borrow diamond core gear, practice on a paving slab or block. Get very comfortable and solid in your stance for holding the tool and moving it through a position that mimics the hole you want to make - can you hold it without dropping from your line?

      @cuebj@cuebj9 ай бұрын

  • Great video as always, what would be great to see is what sealants to use for what’s going in the hole!

    @micro4012@micro4012 Жыл бұрын

    • Some dust control and lung protection is essential. Vacuum and P2 respirator.

      @gregarrell6132@gregarrell6132 Жыл бұрын

  • Great and good quality video again . 👍 👌

    @marcelobadilla5825@marcelobadilla5825 Жыл бұрын

    • Thank you 👍

      @TheDIYGuy1@TheDIYGuy1 Жыл бұрын

    • The detector can find the cavity wall ties? Just to avoid drill over a wall tie 😮

      @marcelobadilla5825@marcelobadilla5825 Жыл бұрын

  • Is this the right saw bit to cut through stucco, too?

    @Son_of_Aragorn@Son_of_Aragorn20 күн бұрын

  • Your presentation skills are getting better and better. Much more natural these days. Good vid, ta.

    @sprint955st@sprint955st Жыл бұрын

    • Much appreciated!👍

      @TheDIYGuy1@TheDIYGuy1 Жыл бұрын

  • If you are drilling through something a bit tougher and maybe using a long extension, try drilling 4 holes at the top, bottom, left and right outer parts of the hole you are trying to cut. This makes the core bit easier to drill through the wall as it hasn’t got as much friction due to the holes. I’ve done this many times, it makes it a lot quicker and easier particularly if you are in a tight spot. Try it out.

    @NeilFirbank-en1yd@NeilFirbank-en1ydАй бұрын

  • good work ! top video !

    @markmcgrath4853@markmcgrath4853 Жыл бұрын

    • Thank you very much!

      @TheDIYGuy1@TheDIYGuy1 Жыл бұрын

  • I was pleased to see you mentioned to put drill on drill only and not hammer! I really wish you would set example and were more ppe your setting yourself up for future I’ll health

    @garethdavies7951@garethdavies79512 ай бұрын

  • Oh how I wish I had one of these, instead it was a bolster and hammer job after drilling a grid of holes then mortar in after. The fun.

    @Nine-Signs@Nine-Signs7 ай бұрын

  • Are drainage pipes cut level also? Or do you need to cut them at the same angle the pipes need to drain? Is that easier than it sounds?

    @Cagstok@Cagstok4 ай бұрын

  • Your new home? Congrats

    @wch4972@wch497210 ай бұрын

  • I have a guild 1000w sds is this powerful enough?

    @MrUM96@MrUM96 Жыл бұрын

  • Pro tip, have a healthy breakfast before you start 😄

    @peterpowers4851@peterpowers48515 ай бұрын

  • Great video...👍🏿👍🏿👍🏿👍🏿

    @patrickbroaden9820@patrickbroaden98203 ай бұрын

    • Thanks 👍

      @TheDIYGuy1@TheDIYGuy13 ай бұрын

  • I cut and drill concrete for a living and I’ve broken my wrist with a 8” bit lol but was also using a hilti hand drill

    @Slidinr32gtst@Slidinr32gtst9 ай бұрын

  • You forgot the dust mask.but also a question do those bits differ, like for dry cutting and wet.applying water

    @kirembweabdulkareem3294@kirembweabdulkareem32946 ай бұрын

  • Nice! I wonder if these can drill through sandstone and granite rock.

    @SSchithFoo@SSchithFoo Жыл бұрын

  • Secondary pro tip if dust/debris mitigation is a concern. Bosch (and other tools brands) makes a suction cup attachment to the shop vac that, when the vacuum is activated, suctions it to the wall. You put your drill or core but through the center of the bristle attachment and all dust and debris get sucked out as you go. Saves a huge mess and minutes of clean up afterwards. This also saves you from wearing a respirator, which you should be for any masonry drilling application. Silica and mortar dust is incredibly harmful to human lungs.

    @JamesSmith-gk8sz@JamesSmith-gk8sz9 ай бұрын

    • 👍

      @TheDIYGuy1@TheDIYGuy19 ай бұрын

  • Thanks again for all the advice you give, i always make sure I never miss a video.

    @danwoodward7738@danwoodward7738 Жыл бұрын

    • I appreciate that!

      @TheDIYGuy1@TheDIYGuy1 Жыл бұрын

  • Very nice

    @cdbbroadfield6154@cdbbroadfield6154 Жыл бұрын

    • Thanks

      @TheDIYGuy1@TheDIYGuy1 Жыл бұрын

  • Core blimey!!! Cracking video 👍🏿👍🏿hole in one ⛳⛳⛳

    @paul_my_plumbs_uk@paul_my_plumbs_uk Жыл бұрын

    • Instagram top tip copper washers on the chuck adapter

      @paul_my_plumbs_uk@paul_my_plumbs_uk Жыл бұрын

    • Thanks 😊

      @TheDIYGuy1@TheDIYGuy1 Жыл бұрын

  • Worth greasing, or anti-sieze paste on threads

    @cuebj@cuebj9 ай бұрын

  • Dust aside - if kick back is most likely going into the internal wall from cavity. Would it not make more sense at this point to drill inside outwards? Some does but avoids kickback and also blow out risk?

    @IAAITKEN@IAAITKEN26 күн бұрын

  • Good video!

    @cherryannablong2832@cherryannablong28327 ай бұрын

    • Thanks!

      @TheDIYGuy1@TheDIYGuy17 ай бұрын

  • My sds drill (dewalt) clutch is not man enough for 4" core drill spend more time trying to get it to bite. I think I need a proper core drill.

    @duncanseath745@duncanseath7454 ай бұрын

  • Where can I get the complete set of this diamond core bits and the drill set

    @vincentoluchukwu1486@vincentoluchukwu148610 ай бұрын

  • Any advice for an overscrewed bit that won’t unscrew??

    @alldensg88@alldensg88 Жыл бұрын

  • Have you got a video where you make a Review on HP2071? 🤔 Would like to see how good it is.

    @lwandilebaliti2595@lwandilebaliti25955 ай бұрын

  • to reduce the blow out on the inside even more I usually run the coredrill in 5-10mm before going outside

    @Lanser1964@Lanser1964 Жыл бұрын

    • Thanks for sharing 👍

      @TheDIYGuy1@TheDIYGuy1 Жыл бұрын

  • Can a Milwaukee 1" 9/16 rotary hammer be used with a core bit to drill through concrete?

    @JoseMartinez-ss1pm@JoseMartinez-ss1pm Жыл бұрын

  • Easy 👍 please do pebble dash concrete next 😂😂😂

    @peterwickett9088@peterwickett9088 Жыл бұрын

  • I have2 concrete wall and 5 feet gap it’s between them how can I make that any idea?

    @jawadakbar133@jawadakbar1335 ай бұрын

  • Was going to say goggles, but also ear plugs and dust mask. Nice job though 😊

    @bbsaid218@bbsaid218 Жыл бұрын

    • Haha yeah probably best. Cheers

      @TheDIYGuy1@TheDIYGuy1 Жыл бұрын

  • Another tip. Be prepared for polyethylene insulation to snow out from the core hole. I've done a hundred of these in the past and i always have a bag or bit of rockwool to hand to stuff in the cavity if i think it has insulation.

    @jacbisgood2221@jacbisgood22219 ай бұрын

    • Good tip

      @TheDIYGuy1@TheDIYGuy19 ай бұрын

  • Hi can you make video about fuse box please

    @howede_destroyergamingandv4338@howede_destroyergamingandv43389 ай бұрын

  • What is the exact drill you are using here?

    @knightbeat@knightbeat9 ай бұрын

  • Drill mode only, no hammer action - is it only specifically for this core bit u're using, or any type of core bits out there? my instructor teach me to use hammer drill function. But, i think that hammer mode will destroy the bits. So im confused 😅

    @mugiwaraluffy9626@mugiwaraluffy96267 ай бұрын

  • If you go up on the ladder, make sure someone holding the ladder for you, and even changing turns! You can get tired quickly higher on the ground holding heavy drill and it will feel more heavier!

    @NeoFreshair@NeoFreshair Жыл бұрын

  • The shank type is this SDS Max? Cannot believe it would be a SDS plus.

    @antosavo3558@antosavo355810 ай бұрын

  • 👍👍👍Thanks

    @Pete.Ty1@Pete.Ty1 Жыл бұрын

    • Welcome 👍

      @TheDIYGuy1@TheDIYGuy1 Жыл бұрын

  • you rock!

    @nathanielluke2084@nathanielluke208421 күн бұрын

    • Thanks 🤟

      @TheDIYGuy1@TheDIYGuy118 күн бұрын

  • Always use the correct core drill with a clutch so save broken arms and wrists,i would not recommend use a standard drill for this type of job !

    @dg2076@dg2076 Жыл бұрын

    • It was a clutched drill 👍

      @michaelshaw8656@michaelshaw8656 Жыл бұрын

    • Exactly. The clue is in the name. Core drill for a core bit. SDS could land you a trip to A&E

      @prawnk1ng@prawnk1ng Жыл бұрын

    • I uses an SDS to core drill all the time, it has a clutch and has never kicked back at me.

      @ddfann@ddfann Жыл бұрын

    • Ok that's acceptable what you've stated But I did just that job some years back with a standard hammer drill. Yes I got got some slight kickback but I got the job done without any broken bones or bruises. Yes I took my time.

      @sydsnott5042@sydsnott5042 Жыл бұрын

    • Young guy I was working with drilled a core hole using a standard SDS. Drill kicked back and he tore his rotator cuff in his shoulder. A month off work and it’s at least 5 years ago now and never been right since 😖. Core drill for a core drill bit every time.

      @darrenpaulgreen@darrenpaulgreen Жыл бұрын

  • Is that the dewalt 133 sds?

    @Lee2k4@Lee2k43 ай бұрын

  • Great video. Just a cautionary word of advice. Protect yourself with a dust mask/respirator in addition to safety glasses. See new warnings on Silica dust and its effects. Cheers

    @tonym527@tonym527 Жыл бұрын

    • Cheers 👍

      @TheDIYGuy1@TheDIYGuy1 Жыл бұрын

  • Can I drill from the inside? I can't reach the brick on the outside because it's at height. Thank you for your help 🙏

    @rainyroad87@rainyroad879 ай бұрын

    • Yes however the dust will be pretty awful

      @TheDIYGuy1@TheDIYGuy19 ай бұрын

  • Hi, what was the name of the wire detector, please?

    @m.b4392@m.b4392 Жыл бұрын

  • 18v drill dream on

    @dash1890@dash18907 ай бұрын
KZhead