Timing Belt Alignment 2008 PT Cruiser . how to set up before replacement
Пікірлер
I accidentally separated the pulley from the bracket. Is there anything I'm supposed to when bolting both back together?
@1221Ralph2 жыл бұрын
The early service info for these engines was incorrect in the positioning of the crank timing mark. Timing mark on the cover had to align with the trailing edge of the tooth with the timing mark. I had one of these engines drive me nuts with that. Apparantly the service info was revised at some point. Also I read that the crank sprocket timing mark was moved the slight amount to allow a straight alignment with the mark on the block. I believe the discrepancy was was on the first 2 production years but im not certain...i was able to find the correct info on alldata.
@JimsRustyOldNuts3 жыл бұрын
Sofar I have not run into that. Thanks that's good info. I appreciate you watching and for Helping.
@NobleAutomotive3 жыл бұрын
What is the mileage/ time requirement fro replacing the timing belt ? I assume that the 2.4 is an interference engine. Thanks
@antonfarquar87993 жыл бұрын
It's a non interference engine. Based on 12000 miles a year it should be replaced at 102000 miles or 8 years. Thank you for watching
@NobleAutomotive3 жыл бұрын
@@NobleAutomotive pretty sure it is interference
@teevee2145 Жыл бұрын
It is an interference engine, and replacement time is a 102000 miles
@NobleAutomotive Жыл бұрын
@@NobleAutomotive 120?? They have schedule a and b
@teevee2145 Жыл бұрын
@@teevee2145the 2.4 is non interference with the pistons contracting the valves. The only reason it would have valve damage, is if the belt broke at high RPM’s. The valve would overlap each other.
@jessieharbinjr.6589 Жыл бұрын
Nice
@timmorris64796 ай бұрын
Thank You
@NobleAutomotive6 ай бұрын
I have a 2007 pt cruiser put a new crank , crank sensor ,cam sensor and new belt in it . lined up the crank and cam pulleys twice car starts right up but idles rough and engine tester says that the crank and cam sensors are not lined up right error code p00216. what am i doing wrong
@teddysimpkins2 жыл бұрын
Now usually if the crank is advanced the engine run rough but be more peppy if it's retarded then it will run real smooth but have poor power so I would think if it was me I would put everything in line Then loosen up the tensioner moved the crank gear back one tooth try that and see what happens it won't hurt your engine
@NobleAutomotive2 жыл бұрын
Now when I say back I mean counter clockwise one tooth
@NobleAutomotive2 жыл бұрын
sorry the error code is p0016
@teddysimpkins2 жыл бұрын
could you call me at 304=691=9338 please
@teddysimpkins2 жыл бұрын
would a bent valve cause a p0016 code
@teddysimpkins2 жыл бұрын
How did he manage to do the job without evacuating & disconnecting the A/C system line?!😲
@pancudowny5 ай бұрын
It's been a while since I've done this video. And I don't really remember any kind of issue with AAC getting in the way.
@NobleAutomotive5 ай бұрын
If you can't make your own marks your pretty much screwed factory marks are a joke if belt broke good luck
I accidentally separated the pulley from the bracket. Is there anything I'm supposed to when bolting both back together?
The early service info for these engines was incorrect in the positioning of the crank timing mark. Timing mark on the cover had to align with the trailing edge of the tooth with the timing mark. I had one of these engines drive me nuts with that. Apparantly the service info was revised at some point. Also I read that the crank sprocket timing mark was moved the slight amount to allow a straight alignment with the mark on the block. I believe the discrepancy was was on the first 2 production years but im not certain...i was able to find the correct info on alldata.
Sofar I have not run into that. Thanks that's good info. I appreciate you watching and for Helping.
What is the mileage/ time requirement fro replacing the timing belt ? I assume that the 2.4 is an interference engine. Thanks
It's a non interference engine. Based on 12000 miles a year it should be replaced at 102000 miles or 8 years. Thank you for watching
@@NobleAutomotive pretty sure it is interference
It is an interference engine, and replacement time is a 102000 miles
@@NobleAutomotive 120?? They have schedule a and b
@@teevee2145the 2.4 is non interference with the pistons contracting the valves. The only reason it would have valve damage, is if the belt broke at high RPM’s. The valve would overlap each other.
Nice
Thank You
I have a 2007 pt cruiser put a new crank , crank sensor ,cam sensor and new belt in it . lined up the crank and cam pulleys twice car starts right up but idles rough and engine tester says that the crank and cam sensors are not lined up right error code p00216. what am i doing wrong
Now usually if the crank is advanced the engine run rough but be more peppy if it's retarded then it will run real smooth but have poor power so I would think if it was me I would put everything in line Then loosen up the tensioner moved the crank gear back one tooth try that and see what happens it won't hurt your engine
Now when I say back I mean counter clockwise one tooth
sorry the error code is p0016
could you call me at 304=691=9338 please
would a bent valve cause a p0016 code
How did he manage to do the job without evacuating & disconnecting the A/C system line?!😲
It's been a while since I've done this video. And I don't really remember any kind of issue with AAC getting in the way.
If you can't make your own marks your pretty much screwed factory marks are a joke if belt broke good luck
Yikes