KZhead

Heavy Duty | Brake Shoe And Wheel Seal Replacement

Semi Workin
2020 ж. 27 Қыр.
670 024 Рет қаралды
Жүктеу

Thanks For Watching!!! Please Like And Subscribe.
Please check out semiworkin.com
Heavy duty brake shoe and wheel seal replacement.
Please check out my other videos: / @semiworkin
Check out some Semi Workin apparel: teespring.com/stores/semi-workin

Пікірлер

  • Can really tell some people in the comments section have either never done on the road breakdown or they just always have all the tools. Sometimes things just arent around or you dont.have time. Lots of admiration for this bloke, quality operator. Personally, and im sure this got done but idve checked for where the waters coming from

    @nickwhite6717@nickwhite67172 жыл бұрын

    • No gloves, waiting on your hand to fall off in 20yrs.

      @vanblue7317@vanblue7317 Жыл бұрын

    • @@vanblue7317 I don't know a single person in this industry with any skin issues, plenty over the 30 yr mark.

      @nickwhite6717@nickwhite6717 Жыл бұрын

  • I would only be presumptuous in asking if you found the underlying issue here. A bad wheel seal isn’t going to cause a big mix of rust and gear oil like that and I would hope you drained the diff and cleaned all components and fixed what I assume was most likely the vent or case leaking causing the water issue also wether it’s a “push in “ seal or not using a seal driver prevents uneven installation of a seal and would prevent that hammer from marring the edges of it as well . Not a bad install job but I would make any of my guys tear that back down and do it right before it rolled from my shop we maintain a fleet of 30 trucks and 20 mid sized to large excavation and a hand full of paving equipment. Taking the extra steps is what prevents unnecessary down time . Also cleaning the plate and surface around the s cam helps keep things from becoming contaminated like the shoes and rollers again aiding in longevity. Aside from that keep em rollin and keep the vids comin

    @bobbysawtelle3561@bobbysawtelle35612 жыл бұрын

    • Yeah, I did notice not a drop of oil came out of the hub when the axle was broke loose. Using a proper seal driver is ssssweet. Before stepped seals I have used an old type 30 brake pushrod. Always caged the brakes, I know it isn't going anywhere. Had a cheapo ratchet strap cut down. To hold shoes in place when installing last spring.

      @dgronzega8073@dgronzega8073 Жыл бұрын

  • Good idea using the bar to check the end play.

    @icelineman@icelineman3 жыл бұрын

  • Thanks. I enjoy watching someone else do this. Great job. Looks good . I’d drive it.

    @termlimitscom8739@termlimitscom87393 жыл бұрын

    • Thanks for watching and commenting!!

      @SemiWorkin@SemiWorkin3 жыл бұрын

  • Excellent! Only if every shop did it exactly like that.

    @user-wf8rr3lh1i@user-wf8rr3lh1i2 ай бұрын

  • I made my own brake spring tool 25 years ago. And still use it .it looks just like the one there selling.

    @rickmccalley6347@rickmccalley63472 жыл бұрын

  • Great work.l love watching this😊.

    @hotrod6427@hotrod64272 жыл бұрын

  • What seal are you using. Hammer install never worked out for me.

    @phild12pd@phild12pd2 жыл бұрын

  • Actually, I am far from criticizing others, because I do not know the circumstances and objectives in detail. However, I winced a little when I see how oil seals are driven in or how the ABS increment can be reinstalled without cleaning. The S-cam of the brake was also installed dry and uncleaned with new rollers. Hm ... that shown leaves an ambivalent impression on me. On the one hand, I like this channel very, very much because it shows things from real everyday life and from a professional perspective. On the other hand, some of the methods shown here are just too ... how should I put it, casual? Anyway or thumbs up for this channel and especially this film! 👍

    @michaelroloff2804@michaelroloff28043 жыл бұрын

    • Thanks for watching!!

      @SemiWorkin@SemiWorkin3 жыл бұрын

  • Thanks for your sharing and tutorial replace seal wheelhub 🙏👍🏻

    @Mekanik135@Mekanik1352 жыл бұрын

  • This is very similar to how I change wheel seals, except I add a small amount of 90W in the hub recess before installing the outer bearing. You can also raise one side of the duals, and let the oil flow to the other side slowly after its put back together. I never cage the brakes, just release them from inside the cab. Good Videos!

    @billyhorton5779@billyhorton57793 жыл бұрын

    • Same here. It doesn't take long to fill the cavity with oil going down the road though, and with a small amount of oil like he did put on ,the bearing is probably not hurt at all. But I always fill the hub first anyway...

      @santerresongarage7486@santerresongarage74863 жыл бұрын

    • Thanks for watching!!

      @SemiWorkin@SemiWorkin3 жыл бұрын

    • Thanks, I'm reassembling my first big truck axle and was confused about this. I'm restoring a 68 IH Loadstar with an RA-39 axle, so I appreciate your clarification.

      @dustinpollard6237@dustinpollard62373 жыл бұрын

    • Eu sempre monto os rolamentos com graxa azul.

      @claudionapoleaoferreira6741@claudionapoleaoferreira67416 ай бұрын

  • Ahh fun times! I worked as a Mechanic's Assistant (GoFer) from when I was 16- 19 years old. Quite when I joined the Army in '83. Done this a few times, then have it inspected. I don't hear the banter with the other mechanics... miss that.

    @bengardiner3867@bengardiner38673 жыл бұрын

    • Thanks for watching!!

      @SemiWorkin@SemiWorkin3 жыл бұрын

    • @@SemiWorkin I'm working on a scale model of a KW W925 to make it very similar to the Movin' On truck from the mid 70s. (Aftermarket Cummins VT 903 with an Eaton 13 speed. Both are different than the ones that are in the kit.) I'm following now and look forward to seeing your content!

      @bengardiner3867@bengardiner38673 жыл бұрын

  • Great Work

    @AliAli-py5yk@AliAli-py5yk3 жыл бұрын

  • Pre-loading bearings is 300 foot pounds. Three times, every time rotate the hub once. Then back off spindle nut and re-tighten using only your hand.

    @realToddLane@realToddLane2 жыл бұрын

  • Is showtime New brakes shoes, with hardware kit, new oil bath seals, Axle gasket, and bearings too. I love my job I love when my hands get a greasy oh yeah baby Nice video dude 👍👍👍

    @OscarMartinez-kg7tl@OscarMartinez-kg7tl3 жыл бұрын

    • Thanks for watching and commenting!!!

      @SemiWorkin@SemiWorkin3 жыл бұрын

  • Never seen a axel com-apart this easy ! I had to use a5-10 lb.sledge @ rap the center of the axel (quarry dump trucks )

    @philbell7952@philbell79522 жыл бұрын

    • Yep I have beaten the shit out of the half shaft with a sledge hammer to get it to come out !

      @davezoom2682@davezoom2682 Жыл бұрын

    • This is a Spicer Dana axle housing without the axle stud wedges , easily removable . Maintenance council has a recommended procedure to tighten wheel bearings on the double nut assembly with a torque wrench and back off .

      @vicpetrishak7705@vicpetrishak7705 Жыл бұрын

  • Perfect video thanks

    @daniloamador928@daniloamador928 Жыл бұрын

  • Want to really see some heavy duty brakes. Change some on a rescue fire truck. Mountain brakes. The drums have fins and are heavy as hell. The shoes have pins that have snap rings to hold them in. Lol

    @hddm3@hddm33 жыл бұрын

    • Thanks for watching!!

      @SemiWorkin@SemiWorkin3 жыл бұрын

  • Nice work 👍👍👍

    @IndianTruckWorkshop@IndianTruckWorkshop2 жыл бұрын

  • Das ist toll video 👍👏👏👏

    @hassankhorasani7273@hassankhorasani72733 жыл бұрын

  • Love your videos! Thank you!

    @equipmentdoc42@equipmentdoc423 жыл бұрын

    • Thanks for watching!!

      @SemiWorkin@SemiWorkin3 жыл бұрын

  • Good but you must clean well the whole surface for you to be able to inspect well in future when the heat builds up it will melt that oil mixture oil and dust...but it's a good job.

    @phaahlatshwere3997@phaahlatshwere39976 ай бұрын

  • Honestly should use a seal tool to install the seal. But can depend on what type of seal you are using. Definitely for a national and cr seal.

    @AngeloBerardi-em3js@AngeloBerardi-em3js3 жыл бұрын

    • Thanks for watching!!

      @SemiWorkin@SemiWorkin3 жыл бұрын

  • Great video as always semi working learning a lot this great content and is educating me very much thanks for the videos keep them coming God bless

    @isaaccharles1189@isaaccharles11893 жыл бұрын

    • Thanks for watching!!

      @SemiWorkin@SemiWorkin3 жыл бұрын

  • Merci pour l'explication

    @OclaryMisinga-js8gs@OclaryMisinga-js8gs8 ай бұрын

  • I just blew a wheel seal on my truck. Thanks.

    @jerrykinnin7941@jerrykinnin79412 жыл бұрын

  • Awesome

    @wvega182@wvega18219 күн бұрын

  • I'm gonna pretend I didn't just see you hubmount a wheelseal with just a hammer lol, but regardless I love your work bro

    @baileysomers2740@baileysomers27403 жыл бұрын

    • Sometimes you just don’t feel like getting up and grabbing the installer

      @unconventionalguitarist9129@unconventionalguitarist91293 жыл бұрын

  • Not sure if diesel guys flat rate but if they do, how much would this job pay? If you're fleet, about how much time would you be given to get this job done?

    @ricardorangel3241@ricardorangel3241 Жыл бұрын

  • Wawww se jeant thanke you very match forever goode job super job 👍👍👍👍👍💪💪💪💪🇩🇿🇩🇿🇩🇿🇩🇿🇩🇿🇩🇿🇩🇿🇩🇿

    @rachidboutoughmas7642@rachidboutoughmas76422 жыл бұрын

  • Nice

    @SmartEngineersOfficial@SmartEngineersOfficial3 ай бұрын

  • Good job

    @daviddabydeen6912@daviddabydeen69123 жыл бұрын

    • Thanks for watching!!

      @SemiWorkin@SemiWorkin3 жыл бұрын

  • At work its hard to get perspective on doing installs of any procedure. The supervisors aren't mechanics, so doing a real good job is not the standpoint at allot of these big companies.

    @kariemdubose5703@kariemdubose5703 Жыл бұрын

  • Did the diff.oil got replaced?

    @Elbribon1@Elbribon12 жыл бұрын

  • For those asking about grease. It uses oil. You never wanna use both.

    @DIAMONDISKEY@DIAMONDISKEY3 жыл бұрын

    • Thanks for watching!!

      @SemiWorkin@SemiWorkin3 жыл бұрын

  • Where can I get the socket to remove the nuts... what is the name of the wrench to remove the large nuts?

    @israelbecerra1497@israelbecerra1497 Жыл бұрын

  • Cómo es el primer mundo que cambian directamente los patines y la campana 🤣 soy de argentina y también me dedico a este rubro, aquí aquí no se pone todo nuevo, se encintan los patines y se rectifican las campanas 🤣🤣

    @tuliolopez1425@tuliolopez142511 ай бұрын

  • Hi How Power rate of this impact wrench? Please help want buy like this

    @massawejacob@massawejacob2 жыл бұрын

  • Desde México Tabasco

    @lorenzantony2252@lorenzantony22522 жыл бұрын

  • Alot of people like to criticize and have their own opinions...who needs tourqe wrench when you have the experience.

    @TolaTrucking@TolaTrucking2 жыл бұрын

  • Sir break shu pr break facing new lag jate hai

    @gurvindersingh6021@gurvindersingh60213 жыл бұрын

  • Super 👌👋👍👍

    @robertotoledo1910@robertotoledo1910 Жыл бұрын

  • Woww! No cleaning before put the news Brake pads?

    @juansantos1614@juansantos16143 жыл бұрын

    • Thanks for watching!!

      @SemiWorkin@SemiWorkin3 жыл бұрын

    • It was cleaned. Just skipped the boring process if you look right before the new brakes got put on.

      @stevenliberadzki9160@stevenliberadzki91603 жыл бұрын

    • Non, its one option 😂😂😂

      @carlosnogueiradacunha1414@carlosnogueiradacunha14143 жыл бұрын

  • Good 👍👍👍👍

    @salehsaleh8141@salehsaleh81412 жыл бұрын

  • Is there any pre-adjustment on the brakes right after installation; or do the slack adjusters do it automatically??

    @brianadams6628@brianadams66283 жыл бұрын

    • Adjust the slacks to spec, check the travel. Should be it

      @unconventionalguitarist9129@unconventionalguitarist91293 жыл бұрын

    • I remember the old manual adjust slacks around 20 yrs ago- that was part of a pre-trip inspection & always had a brake or 2 to adjust or the chicken coup bears would swat U down. Lol 😁

      @brianadams6628@brianadams66283 жыл бұрын

  • I watch Pakistani trucks and there they put so much grease on these parts/shaft it’s different here. Does it need grease or not.

    @mohammedyaqoob7882@mohammedyaqoob78822 жыл бұрын

  • ดูคลิปนี้แล้วทึ่งมาก ที่ลูกปืนล้อใส่แค่น้ำมันซึ่งไม่มากด้วย ตอนถอดทีแรกจึงมีลักษณะของสนิมแต่ลูกปืนยังมีสภาพที่ดี เทคนิคที่ง่ายๆไม่เสียเวลา ถ้าเป็นเมืองร้อนจะใช้วิธีนี้ได้ไหม ๓๑มีค.๖๕

    @AsdDsa-hb1lh@AsdDsa-hb1lh2 жыл бұрын

  • Exactamente tiene q limpiar antes de armar,

    @jorgetoledo3077@jorgetoledo30773 жыл бұрын

  • You are my teacher

    @davdihtoohtoo@davdihtoohtoo2 жыл бұрын

  • Good teacha

    @caliimaan558@caliimaan5583 жыл бұрын

    • Thanks for watching!!

      @SemiWorkin@SemiWorkin3 жыл бұрын

  • How much cost a job like that at dealership just wondering

    @norristaema2810@norristaema281011 ай бұрын

  • what about gear lube looks like its mixed with water , my cam bushing always had to be replaced he didn't even check them

    @realtruth172@realtruth1722 жыл бұрын

  • Is it normal to only oil the bearing rather than pack it with grease ? Will the diff ‘pump’ or splash it into the wheel bearings?

    @duncanrose7985@duncanrose79853 жыл бұрын

    • Oil will run to the outer ends of the axles and fill the hubs but I always put a little grease on mine.

      @johnnyholland8765@johnnyholland87653 жыл бұрын

    • Thanks for watching!! It gets oil through the rear diff.

      @SemiWorkin@SemiWorkin3 жыл бұрын

  • Love ur videos as it is educational program for the young youths.. but let us teach them the right thing as I would never put it on without a good clean all them oil and grease also show them how to check for damages..

    @bobjones3739@bobjones37393 жыл бұрын

    • Thanks for watching!!

      @SemiWorkin@SemiWorkin3 жыл бұрын

  • VÍDEO BEM VISUALIZADO E DEMONSTRATIVO.PARABÉNS.😀😍😍😉☺☺☺😃

    @antoniobraganca3141@antoniobraganca31413 жыл бұрын

  • Did you have to replace the bearings and races, or were you able to just clean them up ?

    @dennissmith460@dennissmith4603 жыл бұрын

    • Thanks for watching!! Bearing/Races were replaced just not shown in video.

      @SemiWorkin@SemiWorkin3 жыл бұрын

  • Limpieza primero que todo,

    @williamfernandogironlopez7643@williamfernandogironlopez76433 жыл бұрын

  • good job. The grease should be applied to the brake contacts or not😅 7:15

    @salimalhinai3034@salimalhinai30343 жыл бұрын

    • Thanks for watching!!

      @SemiWorkin@SemiWorkin3 жыл бұрын

    • Ya. Do you forget to add grease

      @jhondeer8453@jhondeer84533 жыл бұрын

  • Wow

    @reynaldomalapad@reynaldomalapad3 жыл бұрын

  • Todo bien pero por que no limpio la tierra? Digo para que se mire mejor es este mejor.

    @JavierRodriguez-pp8ci@JavierRodriguez-pp8ci3 жыл бұрын

    • ASI HAY MUCHOS MECANICOS ASI LES GUSTA

      @dennissoto5180@dennissoto51802 жыл бұрын

    • La tierra, la grasa, porqué no le dio aceite al retén , grasa a los patines, dejo el buje demasiado atacado ,etc,etc . Una verdadera chapuza.

      @MAN-pl8cu@MAN-pl8cu2 жыл бұрын

  • بس تسلم ايدك

    @mohamedeen1613@mohamedeen16132 жыл бұрын

  • I'm surprised that I didn't see him fill the bearing cavity with grease.

    @blthetube1962@blthetube19623 жыл бұрын

    • Thanks for watching!! This bearing uses oil.

      @SemiWorkin@SemiWorkin3 жыл бұрын

    • Hubs like this use gear oil, not grease.

      @petermoto409@petermoto4093 жыл бұрын

  • What kind of suspension is that? I can't remember seeing one of those.

    @earlycuyler8719@earlycuyler87192 жыл бұрын

    • I believe its a Hendrickson rubber block walking beam. Good on dump trucks.

      @jerrykinnin7941@jerrykinnin79412 жыл бұрын

  • And magically just like that, it’s clean! Wow I need to learn that trick! Also them brake shoes must be the magic pixie dust ones that are self adjusting! LOL

    @jeffreykreft5442@jeffreykreft5442 Жыл бұрын

  • Is the gear lubes full of water looks like rust ??

    @edantonuk690@edantonuk6903 жыл бұрын

    • Thanks for watching!!! The wheel seal was leaking and allowing water to get in.

      @SemiWorkin@SemiWorkin3 жыл бұрын

  • شغل نظيف

    @adelomar2183@adelomar2183 Жыл бұрын

  • Спасибо ютюб за скорость 2x

    @aoh5535@aoh55353 жыл бұрын

  • Exelente

    @julioibarra6441@julioibarra64417 ай бұрын

  • Muy bien pero debería limpiar todo se ve mejor

    @miguemolina627@miguemolina6273 жыл бұрын

  • What are the common socket sizes for the axle nut?

    @noahlittle3841@noahlittle38413 жыл бұрын

    • Thanks for watching!! This set should cover just about all of them: amzn.to/35eFdRW

      @SemiWorkin@SemiWorkin3 жыл бұрын

    • @@SemiWorkin sweet thanks

      @noahlittle3841@noahlittle38413 жыл бұрын

  • Ok well.i ain't no mechanic by any means ..but I a question..i saw no grease going with the bearing? Does this bearing needs no grease?

    @robertdivany1627@robertdivany16273 жыл бұрын

    • It does not need grease because there is already oil in the differential which will lubricate the bearings.

      @mecanopedago@mecanopedago3 жыл бұрын

    • Thanks for watching and commenting these bearings are lubricated with oil from the rear end.

      @SemiWorkin@SemiWorkin3 жыл бұрын

  • Thanks for watchin

    @tanuki379@tanuki3793 жыл бұрын

    • Thanks for watching!!

      @SemiWorkin@SemiWorkin3 жыл бұрын

  • The torge on the hub's is 50 without the cone and 300 to 350 with a cone

    @bradleynevills4444@bradleynevills44443 жыл бұрын

    • Thanks for watching!!

      @SemiWorkin@SemiWorkin3 жыл бұрын

    • @@SemiWorkin yes sir

      @bradleynevills4444@bradleynevills44443 жыл бұрын

  • Thanks for watching

    @mickysmith8851@mickysmith88512 жыл бұрын

  • El compresor de aire que tienen... debieran llevarlo a un taller mecánico de calidad, profesional y autorizado, para que lo arreglen... porque suena más que un bombo en fiesta. (Reparar el compresor... a ustedes les queda grande.... solo sacan y ponen ruedas)

    @mauriciowilson8829@mauriciowilson88292 жыл бұрын

  • You need to check the vent on that axle that's probably where the water's coming in and change that diff lude and always use a torque wrench

    @kevincaler7673@kevincaler76733 жыл бұрын

    • Thanks for watching!!

      @SemiWorkin@SemiWorkin3 жыл бұрын

  • How calling this type of suspension?

    @user-rf8ud2hl1l@user-rf8ud2hl1l3 жыл бұрын

    • Thanks for watching!!

      @SemiWorkin@SemiWorkin3 жыл бұрын

  • 1. He did grease the bearings 2. The seal is a hammer in seal not a press

    @brittneynichole6743@brittneynichole67433 жыл бұрын

    • Thanks for watching and commenting!! You definitely know what your looking at.

      @SemiWorkin@SemiWorkin3 жыл бұрын

  • Helo

    @phongta2006@phongta20063 жыл бұрын

  • Grease insted of oil put into d bearing.nxtwik d bearing is worn out again.

    @danielcasipit475@danielcasipit4752 жыл бұрын

  • Where the grease to protect this bearing?😱😱😱

    @edsonbatista4137@edsonbatista41373 жыл бұрын

    • Thanks for watching!! This bearing uses oil not grease.

      @SemiWorkin@SemiWorkin3 жыл бұрын

  • Parece que al mecanico no le gusta la grasa, en ningun momento se observa engrasar los rodamiento, solo lubrica con algo de aceite , o esta demostrando como se realiza el procedimiento del montage, mmmm hay dudas , parece que la lubricacion si es con aceite , se rellena por el centro del diferencial , descartar la grasa... lo inadecuado y lo correcto es usar un martillo de meno libra al montar el sello ya que estos son lelicado...saludo desde Chile. 🇨🇱🇨🇱🇨🇱🇨🇱

    @manuelvillalobosnavea4300@manuelvillalobosnavea4300 Жыл бұрын

  • على فكره كان المفروض تحط استك تنطر جاز تحت الحافظه اللي بيمشي عليها الظرف اللباد عشان لما بتسخن بتعدي من تحت البليه ليه زيت بيعدي على التيل

    @mohamedeen1613@mohamedeen16132 жыл бұрын

  • Brother, if this was an Indian garage. The needle bearing would have been replaced with 10kgs of grease

    @hruthwindas7056@hruthwindas70562 жыл бұрын

  • No puede al reverse arma los brakes shoes

    @denisgodoy711@denisgodoy7113 жыл бұрын

  • Would be great if he add the tool sizes

    @yusufahmed9715@yusufahmed97153 жыл бұрын

    • Thanks for watching!!

      @SemiWorkin@SemiWorkin3 жыл бұрын

  • Why he didn't put grease on bearings

    @mtxjack@mtxjack3 жыл бұрын

    • Thanks for watching!!

      @SemiWorkin@SemiWorkin3 жыл бұрын

  • Those tapered PC's never come out that easy

    @wcmboss@wcmboss3 жыл бұрын

    • Thanks for watching!!

      @SemiWorkin@SemiWorkin3 жыл бұрын

    • Not on this truck.

      @daronsteele7976@daronsteele79763 жыл бұрын

  • شدة فوق الاوساخ

    @ahmedhashem1931@ahmedhashem19313 жыл бұрын

  • Why you not give the Grease

    @edyharyanto7711@edyharyanto77113 жыл бұрын

  • Bi trục bôi trơn bằng mỡ thì tốt và phù hợp hơn dầu.

    @baotrimaintenance2334@baotrimaintenance23343 жыл бұрын

  • I don’t like the free style tightening of the hub

    @glackaglack1534@glackaglack153418 күн бұрын

  • should always use a stamp before installing the bearing ...

    @akhmadfauzy6843@akhmadfauzy68433 жыл бұрын

    • Thanks for watching!!

      @SemiWorkin@SemiWorkin3 жыл бұрын

    • What do you mean a stamp?

      @bladimirb4526@bladimirb45262 жыл бұрын

    • @@bladimirb4526 What I mean is Grease.....

      @akhmadfauzy6843@akhmadfauzy68432 жыл бұрын

    • @@akhmadfauzy6843 oh yeah good idea

      @bladimirb4526@bladimirb45262 жыл бұрын

    • @@akhmadfauzy6843 he put gear oil on them .they only use oil.The oil runs from the center, / ring and pinion carrier through the axles into the bearings and keeps them lubed that way

      @hopebrowning6300@hopebrowning6300 Жыл бұрын

  • 👍👍👍👍👍

    @user-sf6go8ik4u@user-sf6go8ik4u3 жыл бұрын

    • Thanks for watching!!

      @SemiWorkin@SemiWorkin3 жыл бұрын

  • А стопорная шайба ступичной гайки где?

    @user-6x6truck@user-6x6truck3 жыл бұрын

    • 10:26

      @malyshevvasiliy9541@malyshevvasiliy95413 жыл бұрын

    • @@malyshevvasiliy9541 это стопорная внутренней гайки, а наружней где?? Очень много случаев, когда наружняя гайка откручивается без стопора, а после и ступицы по дороге сами ездят..

      @user-6x6truck@user-6x6truck3 жыл бұрын

  • Girish kaun dalega

    @1ksubin1month30@1ksubin1month303 жыл бұрын

  • It needs bearings and races to.

    @joecanello8369@joecanello83693 жыл бұрын

    • Thanks for watching!!

      @SemiWorkin@SemiWorkin3 жыл бұрын

  • It's not necessary to put grease inside bearings hub .

    @longthonglee3676@longthonglee36763 жыл бұрын

  • No grease?

    @albertlavezares8441@albertlavezares84413 жыл бұрын

    • No grease

      @Jack-qn4vt@Jack-qn4vt3 жыл бұрын

  • Este cubo nao vai graxa.

    @geraldomiranda5412@geraldomiranda54123 жыл бұрын
KZhead