How to Replace Wheel Seal On A Semi Truck Step by Step - Kenworth, Volvo, Freightliner, Cascadia
How to Replace Wheel Seal On A Semi Truck Step by Step - Kenworth, Volvo, Freightliner, Cascadia
#wheelsealreplacementonsemi
Playlist Recommendation: Truck Maintenace - Chassis
► bit.ly/34BKxBu
🤩🤩🤩Exciting News:
Fleet owners and managers,
Do you want to run a smarter trucking business to achieving the goal of SAVING BIG? Discover five comprehensive solutions tailored to tackle fleet challenges head-on. From optimizing aftertreatment system maintenance to boosting diesel engine efficiency, ensuring top-notch warranties, slashing idle time with lithium battery-powered APUs, to gaining total truck control from anywhere, our expertise empowers your fleet for success. Head to our website now for the ultimate fleet transformation!"
► DPF cleaning, aftertreatment emission diagnostic & repairs
fttfleet.com/pages/dpf-cleaning
► Diesel Maintenance - clean the entire engine
fttfleet.com/pages/diesel-mai...
► Best engine and aftertreatment warranty you should have - NTP warranty
fttfleet.com/pages/ntp-warranty
► Remote diagnostic - remote regen and clear faults while your truck is thousands miles away
fttfleet.com/pages/software-s...
► Lithium battery powered APU - most affordable with the best lithium technology
fttfleet.com/pages/electric-apu
Don't forget that we have the most affordable aftermarket DPF, DOC, SCR & Detroit One Box and more in our online store, and don't hesitate to give us a call or send us a text to get a quote.
► fttfleet.com/collections/dies...
Our Specialized Aftertreatment Emission Shop:
Diesel Emissions Specialists
► Address: 1120 High Ave SW Canton, Ohio 44707
► Phone: 330-573-5396 (for appointment & parts order only)
► Email: info@fttfleet.com
► Website: fttfleet.com/
Connect with me on Social Media Platforms:
► KZhead: bit.ly/35YO3kN
► Repair Business: bit.ly/3IELcQJ
► Instagram: bit.ly/3C7hRy6
► TikTok: bit.ly/3QxGHMT
► Facebook Page: bit.ly/2QqBuZ0
► Trucking Facebook Group: bit.ly/34TbQXQ
My Favorite Products for trucking & truck repair needs from Amazon:
► amzn.to/3xZkDn3
Awesome Products and Services We Recommend:
► OTR performance diagnostic tool (super easy scan tool every trucker needs) - use promo code road3333 to get $100 off: bit.ly/3O3wshT
► Rig app (connects mechanics and truck drivers nationwide)
Download the Rig app today: bit.ly/3B7Cbi2
►Motive offers the #1 ELDs and Dashcams for the trucking businesses. Contact Roy Harris from Motive today to find out more about Motive, mention Channel Name to get $100 gift card after signing up.
- 650-547-4061
- roy.harris@gomotive.com
► Join Webull to get up to 12 free stocks for our subscribers.
a.webull.com/i/TruckingFixing...
► MyTee Products is the best place for tarps, straps, chains and more!
bit.ly/3N0IsiP
► Rock Rooster offers the best work boots for you. Use channel exclusive promo code road3333 to get 12% off of your order today. bit.ly/3HFLFDu
► Knowing your cost is crucial to the success of your trucking business. We recommend you to put this FREE trucker calculator tool into your toolbox.
bit.ly/3FzZ1RX
Want to work with our channel? Email us for more details
truckingandfixingwithryan@gmail.com
-----Disclaimer-----
The information and instructions provided by Trucking & Fixing with Ryan KZhead channel is for general informational purposes only. All information on the channel is provided in good faith, however, we make no representation or warranty of any kind, express or implied, regarding the accuracy, adequacy, validity, reliability, availability, or completeness of any information on this channel. Some product links are affiliate links which means if you buy something we'll receive a small commission.
Excellent, I drove for 30 years now its time to learn how to work on them.
Good video. There's got to be other mechanics that get off work and watch someone else work on trucks too lol. I've done too many of these in 20 years and see it done wrong alot. It's satisfying to see other techs do a job well done.
Great job Ryan! I hope you realize you are going to have more work than you will be able to do because your that Good, and honest!!
I appreciate the kindness! Enjoy your comment!
Great video Ryan! Wish I had watched your video first - the video I watched left out some very important details... they showed using a hammer and punch to tighten the nuts. Now I get to go buy a 4" socket and a big torque wrench. And this time I'll add gear oil to the hub as well.
👍
Thank you for this video. This will help in the future. Thank you indeed
You are welcome!
Hi Another great Vid. As I do most of my own repairs ( Apart From Engine strip downs ) whenever I have to change an oil seal I always fit new bearings ( Maybe overkill but bearings are not that expensive ). And an axel Oil change. ( Again oil is relatively cheap ). Enjoy your vids very in formative and you never stop learning from watching others at work..
I like your jack Stan safety always safety
Cool learning this stuff as a Peterbilt parts guy. Little more involved vs our average half ton truck. Also helps understand when a customer of tech is asking for something.
Glad it helpes!
Great video! Love watching this stuff, PLEASE keep them coming!
Great video please keep videos like these coming thank you so much
great job,,simple and professional..thanks..
Thanks for the video. Doing this job tomorrow for the first time on a freightliner if I can get the parts. Done them before on other trucks but it seems like they are all a bit different. I always love knowing what I am getting into.
Great video! Thanks for the in depth explanation. 👍
You are welcome!
I like that seal puller
Thanks for the video Very informative
Awesome channel!! Very informative. Thanks for posting.
Thank you!
Thanks 🇨🇱
Very nice work sir.! Thanks for the video!
Thanks for watching!
Excellent video Ryan. Great explanation. Subscribed.
Thank you!
top job Ryan......interesting work
Thank you!
THANK YOU
You are welcome!
Hi Ryan awesome job explaining thank you !!! Quick question if I need one seal replaced should I do all 4 ??? And whats the normal price for the job I'm in az
Thanks for this video!
You are welcome!
good video, Thx Ryan
Thanks 🙏
Good work 👍
Thank you!
thank's a good show. Dave
Thank you!
Good Video!!
Great video sir. Thanks
Thanks!
Great video brotha
Thank you!
good job ..... thanks
Gr8 video thanks
Thank you!
Got lucky on this one Ryan....the axle didn't have them nasty lock cups over the studs :) They sure can be a pain !! I remember the first time I came across them puppies , I did replace them but, with the split cups not the solids, it sure made it easier the second time around !! Thanks for the vid !
Here is a trick to removing those cone washers if that is what your referring to and yes this works for the solid cone washers. While hitting the end of the drive axle with a large hammer "may" break them loose, this method I was told by a head mechanic in a Peterbilt shop is pretty much guaranteed to work and with so little effort as long as you have a reasonably decent air hammer. First spin all the axle drive nuts loose so they are almost off of their respective studs but make sure they are still on by a few threads. Then take an air hammer and insert a dull chisel attachment, come in at what is almost a 90 degree ( probably 80 degrees ) angle from the axle end flange and set the dull chisel against the side of the bit of cone washer that protrudes. Only "blip" the trigger of the air hammer as it happens so fast that the cone washer shoots out of its bore and you don't want to hit the side of the drive studs and damage them. The reason becomes apparent for keeping the nuts on the ends of the studs as those cone washers will rocket across the shop otherwise !. One would swear how is that going to do much, well it does and once you do a wheel end that the cone washers don't just fall out with a couple of axle end whacks with a hammer and use this method, you will shake your head at how slick it works. Once the washers are all out and the nuts off the studs and you whack the axle end to pop it off the hub, your on your way.
Good job thanks
Thank you!
Excellent 👍✌️
Thanks
Great video..
Thank you!
I always wondered how they put oil in there . Nice video .
Thank you!
Very smart sir😊
Job very well done 👍👍👍
Thanks
Great video! just subscribed .. Thanks
Thank you! Welcome aboard! 👌
so far so good couple things i noted.. my volume was full blast and hard time hearing and shouldn;t there be a safety under besides the jack? thanks good job
Can i ask a question?will changing out old diff oil with new oili n my 26 box truck rear axle cause the axle seals to start leaking?The truck came from the cold east coast boston area and I brought it to California where I live.it has 200 k miles on it. What do u think? thanks very much
Hello Ryan,what size sockets are those axle nuts.
Ok stand corrected after looking thru the comments I found your procedures for this Spicer hub configuration and went to the Spicer web site never assume do your research on the equipment your servicing and follow the procedures in the service manuals that come from the manufacturer.
Are u gonna eventually do in frames once u get your shop open?! That would be awesome vids. I only replaced one drive hub seal on my truck since I had it. Over a million miles on it. Probably get the bearings and seals replaced soon. 😎
We have a one bay shop now. Can offer the bearing and seal job. But in frame job will have to wait until our 3 bay shop build up.
if the lock ring doesnt go on you flip it over first before you tighten it, the seal can be pushed in by hand, while adding oil to the hub is fine, it should be done by checking the diff level first, then jacking the axle up on the opposite side and filling, ensuring the diff is full, it looked like the scam moved when you checked it, which would be worn out bushings,
Thank you!
Is there a specific torque for each inner axle nut depending on the seal type or are they all torqued to 300? Love this videos man keep ‘em coming!
They are torqued depending on what axle nut.
hello, what size is that garage that you're in? what is the height?
What torque wrenches do you use and how often do you have them calibrated?
Can you tell me what is the average price to have this done? Found one starting to let go this morning on pre trip
These hub nuts are torqued to 300 then left, not backed off? How do you know which hubs to leave torqued and which to back off one flat of the nut?
Hey man, my shop doesn’t provide with this tool. Could you tell me the part number for the seal installer please.
Do you have a video on how to replace a rotor?
Easy money
😊
If the dowel pin does not align first flip it over , it may align if not proceed to tighten . To clean the hub bore use a die grinder with a emery flap wheel . Especially on the iron hubs .
Where could I get the torque wrench please if have tool item number that would help also thanks.
Sorry for the long delay, the model number is TQR600E, Serial number is 1112801486. It is a snap on part. I made a video about the specific tool and other information. Video will be released in a couple days! Hope it it’ll help!
You don’t check end play? Crush cones can deform. Actually not recommended to reuse but you can. But I always check end play on any hub that is reusing a crush cone.
If it’s too hard to turn with this type of hub would you do it by feel like a conventional hub or that’s normal? I was replacing a wheel seal and the previous guy who replaced the seal had the inner nut quite loose compared to the outer nut
Ryan what does that seal remover tool run, can send the part number or business info
Just out of curiosity, I just did a seal job on an older model Mack and everyone I talked to said torque the rear nut to about 300 ft lbs then back off a quarter turn, spacer plate, then 300 on outer nut, is that only on the trailer side? Or only on certain models? Or did I just do it wrong? lol
Me to..we own few coal trucks and the inside nut ends up not much more tight than by hand and the outer nut is the one real tight .
@@hopebrowning6300 That is right. Snug the inner nut then lock the outer nut. He did 300 lbs because there was a crush type sleeve between the bearings. That is used now on most newer bearings. I grew up doing older macks and we just snugged the inner bearing. There is a torque spec for no spacer but i cant remember what it is.
Why do wear the reflective gear in the shop
I think it's supplied by uniform company when you order they ask you if you want it with the reflective ,it's better to just have it incase of a service call
Hey bro how much you charge for full pm ,paccar mx13 epa 17
Sorry for the delay. Roughly $150 for labor.
@@truckingandfixing no bad ok ill keep your info ,thank you!
Can u please tell me why I have so much oil coming out through the blow by tube have to put oil every 2 days
It could be the rings or turbo issue.
I have been getting codes for the VGT turbo actuator
Does the hose coming off the turbo going to the charge air cooler have oil in it? If so you'll need a new turbo and VGT actuator. And would also recommend crank case filter
When the iner peace of the seal stays on the spindle hammer that lip flat on top sometimes on bottom it oblongs that peace and you can remove it by hand without damaging anything
Depending on the model of the seal
Oil ? Change axle oil ?
Trying to find that torque wrench and socket used in this video and the links ain’t helping my friend 😅😅
Ryan how do we in touch with you?
Paul, you can check the video description, it shows our business website, phone and email. Hope it helps.
@@truckingandfixing thank you West coast Seabee from a east coast Seabee
i can smell this video
wheel seals can seep its fine..
Ryan you can do all of that without removing the wheels
I still remove the wheels. It's just easier to reassemble without damaging the seal especially out of the shop when I don't have a wheel dolly.
Why not clean the spindle?
Nevermind I found it lol. Carry on
thats how prices rises using wrong tools
Where's the 1 to 5 thousands hub end play this is not the procedures that need to be followed there a are KZhead videos from the truck wheel bearing and hub manfactures on the proper precedures
Ur bearing Preload is wrong. Ur inner nut is ur adjusting Nut and should not be torqued to 300 it should be torqued to 100 and backed off 1/4. Ur outer nut is ur “Jam nut” which should be torqued to 350 ft pounds
This is a Spicer LMS Hub with a spindle spacer, so TMC RP-618, which you are referring to, is incorrect for this setup. As I said in the video, it can be identified by the plastic ring on the locking device, you can find instructions for these online, if you're unfamiliar with them. My instructions are correct, the inner nut is 300 ft lbs up to + 50 ft lbs, you never, ever back these off, period. If the locking ring does not line up, you tighten the inner nut further. The outer nut on the LMS goes to 300 ft lbs, as I said in the video, the Conmet types are usually 200 ft lbs. Again, this setup has a spindle spacer, so TMC RP-618 procedure would not apply to this hub type as it would for a manual adjust hub. Furthermore, these spindle spacer-type setups account for 95% of the wheels I what I see in the business, if guys out there are only torqueing them to 100ft lbs, then backing them off, that may account for the wheels/hubs flying off trucks out there. I have encountered many of these nuts (inner and outer) hand loose when I have went to remove them, most likely from using the incorrect procure when the last guy installed them.
Oh my god No wonder there are wheel offs no one people die from bad wheel seal jobs…. Dont dont this Just take it to your local ta its only $125 labor ish
We had a guy come into our shop once that someone put the inner nut on backwards. The tab on the inner nut was toward the bearing. The whole assembly (HUB, AXLE, TIRES, RIMS, and DRUM) came off and ended up on the bridge of I-95 and another truck hit it and ran into the water and the driver died. The tow truck brought the truck in with the missing wheel and said I got to go to another truck in the same spot. At the time we had no idea the truck that was at our shop caused the accident. A few days later we had, DOT, Highway Patrol, and everyone looking for the guy and for information. We are in SC but he had the wheel seal replaced in FL. The guy was from NC. Not sure what happened. Probably been 15 years ago.
It happens oh so often man… im in ohio and i see prolly 15 ish range every year
What makes you think the guys at the TA are so good?
@@helloneighbor11 their not but if falls off or kills people its covered
@@mikewilson3836 the guy in the video is working for someone. He's covered by someone's insurance just the same