DO YOU EVEN LIFT BRO? | Giving the Pajero a 2 inch Lift
2022 ж. 20 Қар.
16 280 Рет қаралды
We wind up the torsion bars on the Pajero to give us a 2" lift up front.
#mitsubishi #pajero #mitsubishipajero #montero #4wd #4x4 #pajeromods #ozpajerolife #pajero4x4
By coincidence I just indexed my 93 Pajero today. The front was 4+cm low. After removing the bolt and dropping the torsion arm the end that the bolt is in slide off. I just rotated the bracket that the bolt goes thru 2 teeth. I tightened it up and adjusted it so the wheel well arch was the same front and rear. I drove the vehicle forward and back and readjusted the height a few times until it stayed where I wanted it. Odd part is after indexing the drivers side, the passenger side front is now even with the passenger side rear. Looks much better. Informative video. Keep up the good work.
Hey mate, glad it all worked out for you. There's a few ways to re-index you're right. I think it's great you had a crack at it yourself, it feels terrific when you get it right. Thanks for the feedback, appreciated.
Gen 2 🙌🙌❤️
2inch is a safe lifted.for a good 4H proformmance,do not lift over 9cm or the cv joint would break imedately
Thank you much bro!
Thank you mate.... for watching 👍🏻
Have you thought about the 25mm upper ball joint spaces? To prevent the chopping of the bump stops? Grate video love your rig & vids! 🤙🏽
No mate, i had no idea of this! Do you have a pic you can share on here for the viewers mate?
www.machter.com.au/~36426?gclid=Cj0KCQiA4OybBhCzARIsAIcfn9mBVEnBSH7-xrTbnrH1q8zPuYrgReJ5QealfGF3WQzlhk73UJ1BrckaAhpxEALw_wcB Nice work from Kayne viewers, check this out 👍🏻 This is what this channel is all about, sharing ideas.
@@dodgy_garage_4x4 Bj spacers is a safer opcion.
Awesome
Thanks mate... 👍🏻
Good video bud, I wondered if I should do that to my car..
Easy job if you're looking for a bit of lift on the front..... If you are not going to lift it the 2" then don't bother mate. Not sure what size tyres you are running but without the lift you can still get 33's under there pretty easy with minimal scrubbing, it's just when you start to flex that you get a little rubbing.
Hi sir, im planning to reindex my torsion bar as well. May i ask, how many splines/teeths did you reindexed on the bar tp get the 2 inches? Thank you.
Hi mate, I went 2 teeth/splines from memory. But depending on how much tortion your bars still have in them will dictate the correct amount. Try 2, see how you go. I will be doing a re-indexing video sometime in Jan... i have another Gen2 that needs doing. That's for watching 👍
@@dodgy_garage_4x4 awesome! Thank you very much! Yes will reindex mine on my off. 2 splines it is. Currently running 275/65/r18, planning to go higher since will go for bigger tyres. 285/75/r18. Thats around 32.8 inches. Close to 33 think? Looking forward on your next vid. Cheers! 😁
@@KimKim-oo2up just did mine, 2 splines. made a huge difference..
@@Michel251167 got it. Thank you sir! 😁
Hi sir! Merry christmas and a happy new year! Just another quick question. When you reindexed the car with 2 splines/teeth, did you require to use of an AISIN manual locking hub? Or would the new CV jont angle works? Thank you! Cheers! 😁
what suspension do you have in front?
Check this link out, mate... all the info you need. kzhead.info/sun/l6WpitSmpaN-nGg/bejne.html
This one lift up body without added accesories bro?
Did you lift up the body too?
Terry hi, this particular model, the 97 narrow body NK, came with a factory body lift mate.
@@dodgy_garage_4x4 thanks bro . Will try later then
bro how about at the back side.?
Check this video out. Cheers. kzhead.info/sun/l6WpitSmpaN-nGg/bejne.html
Are you Perth scooter?
No mate.