Manufacturing of carbon fiber rim using resin infusion method. Materials from: www.kevytrakentajanverkkokaupp...
Пікірлер
I like that part where the music went "Neenu naneenah neenu, nah neenah neenu..."
@markvincentcocjin3 жыл бұрын
Hi. your work looks really professional. I love it. Congratulations!!!! Wich epoxy glu are you using exactly ? I need to do some joins with fiber carbon parts (the same as you do in your rims) and i can not do a epoxy glu strenght test. Thanks a lot.
@MrRemotos7 жыл бұрын
that music is bloody mind numbing
@wotasod7 жыл бұрын
How did you guys make the mold? I want to make a mold like that one
@luiscastillo11757 жыл бұрын
Nice work! Clean and meticulous!!!
@robgoodsight62165 жыл бұрын
Does cutting the CF sheets on applying decrease the overall strength of the part, as compared to using single sheets ? Are parts made this way reliable for practical purposes where strength is a concern, such as rims itself ?
@srekib17 жыл бұрын
Excuse me may i ask how many hours total needed for you to work on this rim? from the making of mould it self until the final product that have been heated
@satrioharyoprakoso63427 жыл бұрын
nice work, do you make custom rims aswell?
@decoyduck39077 жыл бұрын
Such a weak rim indeed ! just one layer ? are you kidding ? and all the part are just glued together ???? you need to better think the lapping method in order to orientate the fiber with the direction of the stress (in a radial way). Then you have to add some reinforcement carbon rod/strip in it. And please, make it in one piece !!
@skyhacker65 жыл бұрын
Seems to be a rim for the eco-marathon Shell (fuel consume car challenge) so the speed will not exceed 50 km/h with an extremly light car... I think there will not be many stress applied on the rims during the run. But I was a little disappointed too at the first time.
@Manuchao63 жыл бұрын
how well has the wheel held up?
@adamm27166 жыл бұрын
You can just put the vacuum tape on your mold and lay vacuum plastic overtop, it uses less of it and is a bit easier to do, when gluing the parts together you could put a vacuum overtop for better weight distribution and better adhesion, also scuff the edges that will be touching each other as it adds significantly more surface area therefore a much tighter bond, i would heavily suggest adding a valve to your epoxy feed line, that way its easier to get the tube in without sucking a bunch of air, it also allows you to slow down the epoxy filling the mold, ive heard it helps with rigidity and air evacuation, finally why not add spokes? Seems like they would cut down on weight a bit
@kiyosenl.38893 жыл бұрын
Was needing a way to make wheels for a reverse trike project I'm working on, this might work. I need a wheel that is very off-set to one side so that i can get the steering knuckle up inside the wheel. Also considering using carbon fiber for the body and frame with front and rear mounted subframes.
@BartholomewCounty7 жыл бұрын
Hi Mark! I have made also wheels with that high off-set, and the knuckle is located directly above the tyre center line.
@RemmiTeam7 жыл бұрын
I like your way of working :) good job
@JacopoBeppe8 жыл бұрын
great job bro,👌
@msalman54626 жыл бұрын
im new to this why did you cut the pieces up of carbon fiber for the wheel and not just use one piece
@md1234206 жыл бұрын
I like the vacuum infused resin trick, I haven't seen it before. I checked your website and noticed that it left dry spots, did you guys get it worked out or switch to the traditional resin application? I also saw that the wheel cracked at the epoxied seam, have you switched to a stronger epoxy? Or did you try overlapping the material instead of butting it together?
@dickking1908 жыл бұрын
The small dry spots were caused by the spray glue that did not dissolve into the resin as it should have. And the epoxied seam did indeed crack, this structure was later designed completely different due to these problems.
@RemmiTeam7 жыл бұрын
Could this hold the vehicle weight??
@ymaylove7 жыл бұрын
very nice video ,good job!
@teozwtas74406 жыл бұрын
I'd like to know what your thoughts on a carbon motorcycle rim would be? Top speed ~200kph an aluminum hub obviously
@flavortown37815 жыл бұрын
They exist and they arent cheap
@blahblahblahblah28374 жыл бұрын
hello my frandy, you sells this Pierce of vacuum
@leonardonascimento86848 жыл бұрын
Please tell aboit halicopter blade, how make with carbon fiber.
@arifhussain51174 жыл бұрын
No Autoclave?
@AlfaEricWashDC6 жыл бұрын
May I ask what material your mold is made with please?
@shaneschuller2513 Жыл бұрын
what is the weight of the rim?
@tuncaysoylu84917 жыл бұрын
Tavataanks me hei torilla?
@JuisSekasi8 жыл бұрын
Hey, I'm curious about something. Is this CF-epoxy good for making aero-modelling parts? especially wing part. I know there's so many kind of CF out there. 1K, 2K, 3K, etc. But in this video, which ones you use to make that part?
@HH-hp9pe7 жыл бұрын
It is indeed excellent material for aero-modelling parts. There are so many techniques on how to make them and you should search for forums how people make them. On youtube I've seen many videos of making fuselages and wings. The 1K,2K.. number represents the number of fibers in one single tow of the actual cloth. You should be more interested of the weight of the fabric. One that I used was 200g/m^2.
@RemmiTeam7 жыл бұрын
Thank you very much for your explanation
@HH-hp9pe7 жыл бұрын
Can you explain me about degassing resin? And also could you clarify the end part of video where you bond the 2 rims? Actually I am new to this.
@rohanjere37806 жыл бұрын
I think by degassing they meant pulling out the air bubbles.
@-Sean_5 жыл бұрын
Rohan Jere and the reason for bonding the pieces together is easier than making the rim in one piece. This infusion layup system is one of the least expensive processes than prepreg setup. The rims could not be made in one piece, well they could, you just couldn’t get layup materials out of the inner part of the wheel upon completion
@mlinecomposites15 жыл бұрын
can you please give me a brief about how much of the epoxy was used for design i.e. weight ? also i wanted to know what will happen if i put the carbon sheets in different orientations , will it effect the structure strength ? for example if i am taking a 3k twill weave sheet and putting the sheet at 0 degree orientation and the second layer at 45 degrees and next one at 90 degress ? and how to decide how much resin i have to apply on each layer ?
@mayurgupta24227 жыл бұрын
Typically you use 60% carbon fibre to 40% resin but it can vary depending on application I suppose.
@2awesome2927 жыл бұрын
When making parts with this technique(resin infusion) you usually achieve fiber/resin content of 60/40. You always have to make sure to wet all your fibers, but in general the less resin the stronger part. Carbon fiber is very strong along the direction of the fibers so if you have loadings from multiple direction you will need to orientate your fiber parallel to the force vector. This is just very general information and in real it's far more complicated.
@RemmiTeam7 жыл бұрын
@@RemmiTeam, this is very good to know!! Thanks!!
@jmikronis73762 жыл бұрын
hola tengo experencia 6años in este trabajo en Airbus group TANGER y neseta hacer curso aqui in madrid in especialista en compuestos (composites) Garcia's
@hola45877 жыл бұрын
Yes, thank you
@mahmoudfaibar77416 жыл бұрын
How good where the tolerances? did you need to balance the rim?
@emiliomarin8 жыл бұрын
+emilio marin Rim ended up being good. Axial tolerances were very good which is important. After drilling hole for valve it had to be balanced.
@RemmiTeam8 жыл бұрын
Good work :)
@mehul1227 жыл бұрын
Very nice tnx for sharing!
@gustavopomodoro5 жыл бұрын
Can I carry this video to another website? I think this video is doing very well, so I want to share it with friends and other netizens. If you do not agree, I will delete the video I am carrying the moment I see your information. Thank you.
@user-vx2ou6wm5u6 жыл бұрын
Woah, this could easily weigh only a kilogram. By the way, isn't the wheel too weak? You used only 1 or 2 layers of carbon fiber for the sides of wheels. Will it not break?
@wewYugatechreader8 жыл бұрын
+Fred Nedor On the sidewalls there is 3 layers of carbon fiber fabric. Wheel was tested with 8 bars of pressure.
@RemmiTeam8 жыл бұрын
What I love about finland is that it's the home of sako and tikka
@otterconnor9427 жыл бұрын
which release agent have you used? thank you
@atharvapadhye34336 жыл бұрын
Atharva Padhye nanapethet milta tech
@tejasjoshi59186 жыл бұрын
Floor polish??
@RohitReddy46 жыл бұрын
good job
@cylinderheadgasket7 жыл бұрын
how many layers of carbon fiber do you use?
@bagastapa14934 жыл бұрын
1 layer
@henrylima69743 жыл бұрын
that rim looks pretty wide, what kind of bike was it for?
@Ucceah8 жыл бұрын
+Cuda FX This rim was made for special radial tire used in fuel economy racing. If you wanna know more visit www.remmi-team.com
@RemmiTeam8 жыл бұрын
that's because it could not handle and lateral pressure. this is not for the street.
@Bigwingrider18007 жыл бұрын
Kinda cool. Ways to make it stronger for sure. I would recommend crosshatching the shit out of that hub so the epoxy can grip better.
@rustusandroid3 жыл бұрын
is that a bicycle rim?
@loobkooblai35915 жыл бұрын
Sort of, it's for a prototype 1 seater car used in the shell eco marathon. At least I'm assuming that's what they are using it for since their car is right next to it the whole time and CF wheels would be a great improvement to normal aluminum ones. They are usually 3 wheeled and you need to keep them as light as possible
@derickhostetler73185 жыл бұрын
Whould you tell me what epoxy you used?
@argentosebastian4 жыл бұрын
It’s in the video....
@Smokeyr673 жыл бұрын
i have no idea of this stuff but if this rim was for a car why did you make it one full piece.. kinda lokks weird
@k-sugar8 жыл бұрын
cost
@ramodyadav83783 жыл бұрын
tengo experencia in AS A340 A380..... .
@hola45877 жыл бұрын
thats not a rim?
@soullessone46817 жыл бұрын
Those seems are a massive weak point why didn't you over lap them with more fibre. even just a strip would have been better than a butt joint.
@gusbisbal98038 жыл бұрын
+gus bisbal Do you mean the sidewalls? On the sides there is 3 layers of fabric which are laid on each other so that the seams are always in different place.
@RemmiTeam8 жыл бұрын
+gus bisbal Exactly my thought. Why bother with carbon if u just have some glue holding everything together anyway?
@leocurious99198 жыл бұрын
+Leo Curious the parts were glued together by epoxy glue. These glues are extremely strong and they are commonly used in composite industries to bond parts together. This for sure is not the weak point of the structure.
@RemmiTeam8 жыл бұрын
I am pretty sure that Gus and Leo are right. Butt joints are a major weak point, and epoxy in itself is very brittle. You really need to join those seems with another layer of carbon fiber on top, or make it out of a single piece of CF. Do a simple test with two epoxy infused rectangular pieces of carbon fiber, and you will see that it will break at the butt-joint every time.
@thomaslarang52518 жыл бұрын
Tom Lariot read his reply, they are three layers of off set seams. there IS another layer over each seam
@gusbisbal98038 жыл бұрын
Thanks guys.
@campanileLabs2 жыл бұрын
The same technique that Köenigsegg uses to fabricate wheels like this one for it's cars
@vaioskaliakoudas63887 жыл бұрын
ci puede ayoda me
@hola45877 жыл бұрын
Video was much better after I turned the sound off and played Five Finger Death Punch instead.
@feathercarbon5 жыл бұрын
Need to get the wheel balanced...
@madjimms7 жыл бұрын
This factory driving me crazy , Just a piz
@audiobanker17717 жыл бұрын
मुझे चाहिये
@ramodyadav83783 жыл бұрын
That looks like a carbonfiber dinner plate
@Frank_Hwhite6 жыл бұрын
U didn't show how you created a mold
@funaticsworld26486 жыл бұрын
looks like it was cnc milled (which they have showed in other videos)
@radihaydos956 жыл бұрын
remove the music just leave the live audio please
@PabloPazosGutierrez5 жыл бұрын
Lol this guy has that uber hold music
@AdventureWithAnthony5 жыл бұрын
The music tells the whole story, some narration would give us half a clue what’s going on..
@mikeb30102 жыл бұрын
I'm no expert, but that seems like a pretty inefficient design. What were your main goals in making this? How did it work out? Would you do it this way again?
@operator80145 жыл бұрын
well then
@cyancoyote73668 жыл бұрын
scissors on the vac bag, thats a carton!!!
@Theef3kw5 жыл бұрын
01:25 - when the scissors starts to gliiiide. HNNNNNGGGG.
@tikkivolta28546 жыл бұрын
not good process
@BerhampurH6 жыл бұрын
You guys need to improve your method
@georgemicheal90366 жыл бұрын
Έλληνας ;
@apostolisstathis91415 жыл бұрын
Looks like a frisbee rather than a rim. But ok.
@PeopleOfCasinos6 жыл бұрын
wow this music is much better than most free trash people use. why are people complaining? also i dont like listening to most vocal music its 98% trash anyway. That being said it would be much better if they didn't use music and talked about what they're doing even though i already know most of what their doing
@darkshadowsx59494 жыл бұрын
dragging your bag across the table where you do your cutting in never a good idea
@jamesperreault45065 жыл бұрын
sounds painful
@darkshadowsx59494 жыл бұрын
Hi James, you are absolutely right about that. If you look very closely you can see there is a piece of styrofoam between bag and table to protect the bag from being punctured.
@RemmiTeam4 жыл бұрын
Excellent except for the terrible music loop omg, my ears are bleeding....
@MixwizardTom6 жыл бұрын
Great song thanx for the upload eh! If you want to win .... eh
@av69665 жыл бұрын
The music forced me to stop watching. I really wanted to see this through to the end.
@dowatchagotado7 жыл бұрын
I'm sorry for that. We will learn about these comments and in future try something instead the music. Please subscribe to our channel, we will be publishing new video of making a carbon fiber monocoque.
@RemmiTeam7 жыл бұрын
Oh please...did it ever occur to you to turn off the audio, or turn down the volume... Your comment is beyond stupid...but then again, that is the bar you set for yourself
@prowrench79894 жыл бұрын
Hyvä video, mutta musiikki ei ollut hyvä.
@gregthornthwaite80115 жыл бұрын
I am sorry for saying this but I regreted watching this video.
@marshall_mj88773 жыл бұрын
Berisik amat musik nya👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎🏿👎👎🏾
@urban_pose7023 жыл бұрын
Combustion engine is dead. Dont waste your skills on greenwashing oil industry.
@pangrac15 жыл бұрын
no pre preg or oven or autoclave GG:) 100% failure from little abuse
@Zohar-Modifier6 жыл бұрын
It's called a wheel! The edge of a toilet bowl or something that doesn't spin is called a rim. Mostly Idiots call wheels rims not trying to be rude. Nice professional looking video with a goofy dumb looking title.
@johnwaldron23557 жыл бұрын
John Waldron chill out, when people say "rims" it usually means the part of a "wheel" not including the tire. tire plus rim equals wheel.
@sytran6667 жыл бұрын
TBH you are wrong, but people do say rims instead of wheels depending on where you are from. Do you go to the shop and ask for four new wheels or tires? Who cares really? Bahahaa
@djrowe0076 жыл бұрын
John Waldron, the rim is the part that holds the tire on. If you ever look at the construction of a bike wheel you'll notice they have 4 parts the hub the spokes the rim and the tyre (and tube, depending of tyre type) as they made the seat for the tyre, what they made is a rim
I like that part where the music went "Neenu naneenah neenu, nah neenah neenu..."
Hi. your work looks really professional. I love it. Congratulations!!!! Wich epoxy glu are you using exactly ? I need to do some joins with fiber carbon parts (the same as you do in your rims) and i can not do a epoxy glu strenght test. Thanks a lot.
that music is bloody mind numbing
How did you guys make the mold? I want to make a mold like that one
Nice work! Clean and meticulous!!!
Does cutting the CF sheets on applying decrease the overall strength of the part, as compared to using single sheets ? Are parts made this way reliable for practical purposes where strength is a concern, such as rims itself ?
Excuse me may i ask how many hours total needed for you to work on this rim? from the making of mould it self until the final product that have been heated
nice work, do you make custom rims aswell?
Such a weak rim indeed ! just one layer ? are you kidding ? and all the part are just glued together ???? you need to better think the lapping method in order to orientate the fiber with the direction of the stress (in a radial way). Then you have to add some reinforcement carbon rod/strip in it. And please, make it in one piece !!
Seems to be a rim for the eco-marathon Shell (fuel consume car challenge) so the speed will not exceed 50 km/h with an extremly light car... I think there will not be many stress applied on the rims during the run. But I was a little disappointed too at the first time.
how well has the wheel held up?
You can just put the vacuum tape on your mold and lay vacuum plastic overtop, it uses less of it and is a bit easier to do, when gluing the parts together you could put a vacuum overtop for better weight distribution and better adhesion, also scuff the edges that will be touching each other as it adds significantly more surface area therefore a much tighter bond, i would heavily suggest adding a valve to your epoxy feed line, that way its easier to get the tube in without sucking a bunch of air, it also allows you to slow down the epoxy filling the mold, ive heard it helps with rigidity and air evacuation, finally why not add spokes? Seems like they would cut down on weight a bit
Was needing a way to make wheels for a reverse trike project I'm working on, this might work. I need a wheel that is very off-set to one side so that i can get the steering knuckle up inside the wheel. Also considering using carbon fiber for the body and frame with front and rear mounted subframes.
Hi Mark! I have made also wheels with that high off-set, and the knuckle is located directly above the tyre center line.
I like your way of working :) good job
great job bro,👌
im new to this why did you cut the pieces up of carbon fiber for the wheel and not just use one piece
I like the vacuum infused resin trick, I haven't seen it before. I checked your website and noticed that it left dry spots, did you guys get it worked out or switch to the traditional resin application? I also saw that the wheel cracked at the epoxied seam, have you switched to a stronger epoxy? Or did you try overlapping the material instead of butting it together?
The small dry spots were caused by the spray glue that did not dissolve into the resin as it should have. And the epoxied seam did indeed crack, this structure was later designed completely different due to these problems.
Could this hold the vehicle weight??
very nice video ,good job!
I'd like to know what your thoughts on a carbon motorcycle rim would be? Top speed ~200kph an aluminum hub obviously
They exist and they arent cheap
hello my frandy, you sells this Pierce of vacuum
Please tell aboit halicopter blade, how make with carbon fiber.
No Autoclave?
May I ask what material your mold is made with please?
what is the weight of the rim?
Tavataanks me hei torilla?
Hey, I'm curious about something. Is this CF-epoxy good for making aero-modelling parts? especially wing part. I know there's so many kind of CF out there. 1K, 2K, 3K, etc. But in this video, which ones you use to make that part?
It is indeed excellent material for aero-modelling parts. There are so many techniques on how to make them and you should search for forums how people make them. On youtube I've seen many videos of making fuselages and wings. The 1K,2K.. number represents the number of fibers in one single tow of the actual cloth. You should be more interested of the weight of the fabric. One that I used was 200g/m^2.
Thank you very much for your explanation
Can you explain me about degassing resin? And also could you clarify the end part of video where you bond the 2 rims? Actually I am new to this.
I think by degassing they meant pulling out the air bubbles.
Rohan Jere and the reason for bonding the pieces together is easier than making the rim in one piece. This infusion layup system is one of the least expensive processes than prepreg setup. The rims could not be made in one piece, well they could, you just couldn’t get layup materials out of the inner part of the wheel upon completion
can you please give me a brief about how much of the epoxy was used for design i.e. weight ? also i wanted to know what will happen if i put the carbon sheets in different orientations , will it effect the structure strength ? for example if i am taking a 3k twill weave sheet and putting the sheet at 0 degree orientation and the second layer at 45 degrees and next one at 90 degress ? and how to decide how much resin i have to apply on each layer ?
Typically you use 60% carbon fibre to 40% resin but it can vary depending on application I suppose.
When making parts with this technique(resin infusion) you usually achieve fiber/resin content of 60/40. You always have to make sure to wet all your fibers, but in general the less resin the stronger part. Carbon fiber is very strong along the direction of the fibers so if you have loadings from multiple direction you will need to orientate your fiber parallel to the force vector. This is just very general information and in real it's far more complicated.
@@RemmiTeam, this is very good to know!! Thanks!!
hola tengo experencia 6años in este trabajo en Airbus group TANGER y neseta hacer curso aqui in madrid in especialista en compuestos (composites) Garcia's
Yes, thank you
How good where the tolerances? did you need to balance the rim?
+emilio marin Rim ended up being good. Axial tolerances were very good which is important. After drilling hole for valve it had to be balanced.
Good work :)
Very nice tnx for sharing!
Can I carry this video to another website? I think this video is doing very well, so I want to share it with friends and other netizens. If you do not agree, I will delete the video I am carrying the moment I see your information. Thank you.
Woah, this could easily weigh only a kilogram. By the way, isn't the wheel too weak? You used only 1 or 2 layers of carbon fiber for the sides of wheels. Will it not break?
+Fred Nedor On the sidewalls there is 3 layers of carbon fiber fabric. Wheel was tested with 8 bars of pressure.
What I love about finland is that it's the home of sako and tikka
which release agent have you used? thank you
Atharva Padhye nanapethet milta tech
Floor polish??
good job
how many layers of carbon fiber do you use?
1 layer
that rim looks pretty wide, what kind of bike was it for?
+Cuda FX This rim was made for special radial tire used in fuel economy racing. If you wanna know more visit www.remmi-team.com
that's because it could not handle and lateral pressure. this is not for the street.
Kinda cool. Ways to make it stronger for sure. I would recommend crosshatching the shit out of that hub so the epoxy can grip better.
is that a bicycle rim?
Sort of, it's for a prototype 1 seater car used in the shell eco marathon. At least I'm assuming that's what they are using it for since their car is right next to it the whole time and CF wheels would be a great improvement to normal aluminum ones. They are usually 3 wheeled and you need to keep them as light as possible
Whould you tell me what epoxy you used?
It’s in the video....
i have no idea of this stuff but if this rim was for a car why did you make it one full piece.. kinda lokks weird
cost
tengo experencia in AS A340 A380..... .
thats not a rim?
Those seems are a massive weak point why didn't you over lap them with more fibre. even just a strip would have been better than a butt joint.
+gus bisbal Do you mean the sidewalls? On the sides there is 3 layers of fabric which are laid on each other so that the seams are always in different place.
+gus bisbal Exactly my thought. Why bother with carbon if u just have some glue holding everything together anyway?
+Leo Curious the parts were glued together by epoxy glue. These glues are extremely strong and they are commonly used in composite industries to bond parts together. This for sure is not the weak point of the structure.
I am pretty sure that Gus and Leo are right. Butt joints are a major weak point, and epoxy in itself is very brittle. You really need to join those seems with another layer of carbon fiber on top, or make it out of a single piece of CF. Do a simple test with two epoxy infused rectangular pieces of carbon fiber, and you will see that it will break at the butt-joint every time.
Tom Lariot read his reply, they are three layers of off set seams. there IS another layer over each seam
Thanks guys.
The same technique that Köenigsegg uses to fabricate wheels like this one for it's cars
ci puede ayoda me
Video was much better after I turned the sound off and played Five Finger Death Punch instead.
Need to get the wheel balanced...
This factory driving me crazy , Just a piz
मुझे चाहिये
That looks like a carbonfiber dinner plate
U didn't show how you created a mold
looks like it was cnc milled (which they have showed in other videos)
remove the music just leave the live audio please
Lol this guy has that uber hold music
The music tells the whole story, some narration would give us half a clue what’s going on..
I'm no expert, but that seems like a pretty inefficient design. What were your main goals in making this? How did it work out? Would you do it this way again?
well then
scissors on the vac bag, thats a carton!!!
01:25 - when the scissors starts to gliiiide. HNNNNNGGGG.
not good process
You guys need to improve your method
Έλληνας ;
Looks like a frisbee rather than a rim. But ok.
wow this music is much better than most free trash people use. why are people complaining? also i dont like listening to most vocal music its 98% trash anyway. That being said it would be much better if they didn't use music and talked about what they're doing even though i already know most of what their doing
dragging your bag across the table where you do your cutting in never a good idea
sounds painful
Hi James, you are absolutely right about that. If you look very closely you can see there is a piece of styrofoam between bag and table to protect the bag from being punctured.
Excellent except for the terrible music loop omg, my ears are bleeding....
Great song thanx for the upload eh! If you want to win .... eh
The music forced me to stop watching. I really wanted to see this through to the end.
I'm sorry for that. We will learn about these comments and in future try something instead the music. Please subscribe to our channel, we will be publishing new video of making a carbon fiber monocoque.
Oh please...did it ever occur to you to turn off the audio, or turn down the volume... Your comment is beyond stupid...but then again, that is the bar you set for yourself
Hyvä video, mutta musiikki ei ollut hyvä.
I am sorry for saying this but I regreted watching this video.
Berisik amat musik nya👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎🏿👎👎🏾
Combustion engine is dead. Dont waste your skills on greenwashing oil industry.
no pre preg or oven or autoclave GG:) 100% failure from little abuse
It's called a wheel! The edge of a toilet bowl or something that doesn't spin is called a rim. Mostly Idiots call wheels rims not trying to be rude. Nice professional looking video with a goofy dumb looking title.
John Waldron chill out, when people say "rims" it usually means the part of a "wheel" not including the tire. tire plus rim equals wheel.
TBH you are wrong, but people do say rims instead of wheels depending on where you are from. Do you go to the shop and ask for four new wheels or tires? Who cares really? Bahahaa
John Waldron, the rim is the part that holds the tire on. If you ever look at the construction of a bike wheel you'll notice they have 4 parts the hub the spokes the rim and the tyre (and tube, depending of tyre type) as they made the seat for the tyre, what they made is a rim
5:14 degassing resin?!?! Hahaha
Please tell about halicopter blads, how make?
Worst rim ever.
This is wrong and dangerous