EZABL Install 🔥 Ender 3 v2 [ Step-by-Step Guide 2021 ]
This is a detailed, step by step guide for installing an EZABL Pro, an OEM LCD Screen, and a Filament runout sensor on your Ender 3 V2. Check the timestamps listed below to skip to the most relevant part of the guide to help you. All of the parts used in this video are listed below, as well as any of the other guides mentioned throughout the video. If you have any questions at all, please feel free to ask them in the comments below, or join our discord server.
#3dprinting #ender3v2
Timestamps:
0:00 - Intro
1:38 - Setting up the firmware
9:08 - Installing the new LCD Screen
14:00 - Installing the EZABL
25:30 - EZout & Filament runout sensor
29:00 - Powering the EZABL
39:05 - Setting up the EZABL
48:09 - Slicer Settings & Test Print
52:59 - Setting the Z-Offset
56:38 - Outro
--------Parts Used In This Video--------
EZABL:
www.th3dstudio.com/product/ez...
OEM LCD Screen:
www.th3dstudio.com/product/cr...
Filament Runout Sensor:
www.th3dstudio.com/product/en...
LCD Screen Bracket:
www.th3dstudio.com/product/en...
EZABL Sensor Mount:
www.th3dstudio.com/product/ez...
Solid Bed Mounts for Ender 3 V2:
www.th3dstudio.com/product/th...
EZABL AC Power Adapter:
www.th3dstudio.com/product/ez...
TH3D Store:
www.th3dstudio.com/shop/?share...
--------Guides & Downloads Mentioned In The Video--------
VSCode Install & Setup Guide:
• Setting up VSCode for ...
Unified 2 Firmware download for Ender 3 V2 (When replacing the LCD Screen):
www.th3dstudio.com/hc/downloa...
EZABL Starting Gcode for Slicer:
www.th3dstudio.com/hc/product...
Unified 2 Firmware download for Stock Ender 3 V2:
www.th3dstudio.com/hc/downloa...
Discord Server:
/ discord
Support the channel with Bitcoin:
Bitcoin Wallet: bc1q9tk26lwzg3qnmh85ez4kxqtams6f6cu433mnxu
--------3D Printers, Upgrades & Mods--------
Ender 3 V2:
amzn.to/3jFduQ4
Ender 3 Pro:
amzn.to/3aLLirN
CR10 V3:
amzn.to/32USHRd
Bltouch Kit:
amzn.to/375q1HC
Raspberry Pi 4 2GB:
amzn.to/2Nn4DX6
Raspberry Pi 4 Full Starter Kit:
amzn.to/2OlAQyC
USB Webcam used for Raspberry Pi:
amzn.to/3jMuZ0S
TH3D ezFlex PEI Bed Sheet:
www.th3dstudio.com/product/ez...
Creality Direct Drive Upgrade Kit:
amzn.to/3d5aYl6
Upgraded Bed Springs:
amzn.to/3aVGyPr
Extra .4 Nozzle Kit:
amzn.to/3b0Zex8
Digital Calipers:
amzn.to/3qhfTmw
Monitor cable for Raspberry Pi:
amzn.to/3jI2i5b
40mm LED Fans for Raspberry Pi:
amzn.to/2Z6bxD1
TH3D Upgraded Extruder:
www.th3dstudio.com/product/ez...
TH3D PTFE Tough Tube:
www.th3dstudio.com/product/to...
Desiccant Packs: (keep your filament dry)
amzn.to/3d56CKA
Airtight Storage Container for filament:
amzn.to/3abKn3I
Enclosure Kit:
amzn.to/2U6dIYj
--------3D Printing Filaments--------
Black Sainsmart TPU:
amzn.to/2N0C9me
Green Sainsmart TPU:
amzn.to/3d5UQQq
White Sainsmart TPU:
amzn.to/3pcCQGc
Eryone Galaxy Sparkly Glitter PLA:
amzn.to/2YbkgU4
GIZMO Dorks PLA Pack:
amzn.to/2URZ073
Black SUNLU PLA:
amzn.to/39apN3o
White SUNLU PLA:
amzn.to/3phaafY
Some of the links listed above are affiliate links to Amazon & TH3D. This means that if you choose to purchase any of the products after clicking on the links, I will receive a small commission, at no extra cost to you. This is a small way to help support the channel, and if you choose to purchase anything it is greatly appreciated!
Tim and his crew are top notch, always deliver a quality product and customer service. I have the EZABL Pro on my Sidewinder with the EZLCD, works like a charm.
No doubt! I've always been highly impressed when dealing with them.
I have the EZABL sensor running on a BTT Octopus Pro 429 boar4d and BTT TFT35 E3 Touch screen running the latest firmware for the screen and Marlin 2.1.x. I believe that at the step where you bring the printhead Z height from +5 to +0 after you do the home. You Manually leveled the bed. But if you have on your printer's screen an option called Babystepping then use that option and a piece of paper or a business card to move the print head down to the correct position. Then make sure you press the SAVE to EEPROM option to SAVE SETTINGS! I find for my REVO Hotend that using a Business card works better because it is a little thicker therefore I have to readjust the "printing first layer Z offset" less than if I use a piece of printer paper. I have tried both methods. One other tip: If you bought the rubber standoffs/ Kit or what ever these are called from TH3D to replace your Bed Springs then you don't have to fully level you bed initially by the four corner method. I just bought the rubber spacers so I have not tried this method, Yet. It looks like there is a metal sleeve inside of a round rubber piece.
Instead of routing the black EZABL cable next to the bed, you could use the mounting clips included in the Sidewinder installation and run the wire in the bottom slot using the clips to keep the wire tucked in the groove. Good informative video.
I didn't have any clips :( lol but that is a good idea. The wire does sit nicely in the grooves though.
Great Video. Lots of good upgrades here.
Thanks!
Lcd screen from th3d is actually from bigtreetech. Ezabl seems to be lighter from original and all plastic now.
Can i ask why you changed screens?
And I am subscribed
Thanks bro :)
best thing i ever done was bin the creality crap th3d is great th3d uk tim lets do it
The VSCode does create unique .bin files because it adds date and time in the name.
Appreciate that info!
Can you use the original Ender 3 V2 screen?
as someone who doesn't have the tools that came with the machine. Anyone know the thickness of that wrench?
Yer thought it would be simple but thanks
It's pretty simple. I show every single step.
Why not just print your own mount for the EZABL to utilize the two existing holes?
Yea, that would have been a better idea.
you turned a v2 into a Ender 3-Pro, u went backwards smh