KZhead

How to make high-quality hand thread tap(don't forget the like)

Master mind
2023 ж. 14 Шіл.
1 421 958 Рет қаралды
Жүктеу

Broken and disposable tools are always usable and functional and will only require a little innovation and creativity
The best way to make hand thread tap: • The best way to make h...
How to make a handmade drill bit: • How to make a handmade...

Пікірлер

  • Great build and very innovative use of a drill bit with spiral flutes. There have been a lot of makers with straight flutes, but I like the spiral, and old bits are fairly easy to come by. Thanks and cheers! Someone should forward this vid to homemade tools.

    @howder1951@howder19519 ай бұрын

    • I'm so glad you enjoyed it my friend🙏👍💐

      @Mastermind-@Mastermind-9 ай бұрын

    • Делал я со сверла только с конуса на М12шаг 1,75 левый , отлично получилось .

      @user-fd3dy3hw6o@user-fd3dy3hw6o2 күн бұрын

  • Красавчик ! Чистюля !! Приятно , когда все почти идеально !!! Успехов ❤ , за наждачку и образив минус😢

    @user-mw5iu4iz6q@user-mw5iu4iz6qАй бұрын

  • Absolute HOCHACHTUNG! Das war der Beweis, daß es noch echte Handwerker gibt! 🎉

    @HorstJarnuszak@HorstJarnuszak5 ай бұрын

    • 🙏🙏🙏💐

      @Mastermind-@Mastermind-5 ай бұрын

  • Great job my friend! You left out only one thing, tempering. it is very important that the tool is not brittle, because one wrong move can break the teeth. in the case of tool steels, they undergo multi-step hardening, which makes the material very resistant. great job by the way!

    @Matthews_Tools@Matthews_Tools9 ай бұрын

    • Thanks for the watching and the tips my dear friend🙏🙏💐💐

      @Mastermind-@Mastermind-9 ай бұрын

    • For tempering steel that needs to stay very hard, like for a tap, sometimes just boiling water is hot enough, and if that leaves it to brittle, an oven at 150 degrees C might work

      @ALittleBitOfEverything-wd9ee@ALittleBitOfEverything-wd9ee17 күн бұрын

  • With no doubt, the very best tap. I know because I made some myself in desperation, on weekends where I need it one and every shop were shut, but the cheapest tap would do the job in good hands.

    @user-bl6it8ls6c@user-bl6it8ls6c4 ай бұрын

    • Thank you so much my dear friend🙏🙏🙏💐

      @Mastermind-@Mastermind-4 ай бұрын

  • This video really makes me appreciate just being able to buy one.

    @henmich@henmich6 ай бұрын

    • 🙏🙏💐❤️

      @Mastermind-@Mastermind-6 ай бұрын

  • A handmade tool is always a reason to be proud. Congratulations and best regards 😀.

    @ZygmuntKiliszewski@ZygmuntKiliszewski2 ай бұрын

    • Exactly, I feel proud everytime I use things that I made or restored

      @racing_mntage1584@racing_mntage1584Ай бұрын

    • Thank you very much my friend I hope other friends like you will understand the value of this work and not be superficial

      @Mastermind-@Mastermind-20 күн бұрын

    • 🙏🙏❤️👍

      @Mastermind-@Mastermind-20 күн бұрын

    • Thank you for the like 😀.

      @ZygmuntKiliszewski@ZygmuntKiliszewski20 күн бұрын

  • Witaj Fachmanie młody i najwyższy Szacunek od starego zawodowca, super robota!

    @zygmuntszulowski4197@zygmuntszulowski41979 ай бұрын

    • Dziękuję bardzo mój dobry przyjacielu🙏🙏💐

      @Mastermind-@Mastermind-9 ай бұрын

  • You should note that drill diameter are actually slightly smaller than stated size and tap diameters are slightly larger, so take care for a screw to fit the tapped hole!

    @garthdaddy7438@garthdaddy74389 ай бұрын

  • Damn fine work! That was some quality stuff. It's also nice to see someone that actually does things correctly and properly when it comes to machining and metal working. Nowadays I see so many people on the interweb KZheads that cut corners, force things, and sometimes simply just don't know what they are doing. Then they make videos and pass those bad habits on to others 😢. I also appreciate that you know how to correctly grind your own lathe bits which is something that all machinist should at least know how to do whether they use indexable bits or not. That is definitely a dying art. You are quite impressive my good sir, keep up the good work! 👍👏😊

    @JesseCase@JesseCase9 ай бұрын

    • Thank you very much, my good friend, and I will try to offer the best as much as I can🙏🙏💐💐

      @Mastermind-@Mastermind-9 ай бұрын

    • @@Mastermind- good stuff Maynard

      @samhiscox3511@samhiscox35119 ай бұрын

  • Very well done. I keep in mind your way to sharpen a tap drill.

    @cryon7260@cryon72609 ай бұрын

    • Yes, thanks👍

      @Mastermind-@Mastermind-9 ай бұрын

  • Pensa num cara treinado! Belo trabalho! Valeu muito obrigado!!!

    @aubrymacielpereirafilho3017@aubrymacielpereirafilho30177 ай бұрын

    • Muito obrigado meu bom amigo🙏

      @Mastermind-@Mastermind-6 ай бұрын

  • Good video. I will try this method some time. Cheers Rob

    @Xynudu@Xynudu9 ай бұрын

    • I am very happy my good friend cheers

      @Mastermind-@Mastermind-9 ай бұрын

  • The old way of screw cutting took skill and a sharp brain, it's scandalous how the salary of a toolmaker or machinest was so average for such a skilled job. Dying breed nowadays

    @martolomew956@martolomew956Ай бұрын

  • Do I understand correctly that first you release the metal (remove the quench), and then re-quench after processing? Cool work, but for those who have a welding machine or a heating furnace.

    @andrewlensky632@andrewlensky6329 ай бұрын

    • You almost guessed right, my friend

      @Mastermind-@Mastermind-9 ай бұрын

    • Heated and left to cool to a anneal the hardened metal, then after it was quenched in oil that steals some carbon from oil for hardness but it quickly cools the steel to lock in the rearranging molecules.

      @wellscody86@wellscody865 ай бұрын

  • Great job 👍

    @innovationtime20@innovationtime209 ай бұрын

    • Thanks for the visit🙏👍

      @Mastermind-@Mastermind-9 ай бұрын

  • Magnificent work.I need to make an m20 nut. I'm going to take advantage of the idea and do it with a 22 inch drill that I have in the workshop ... ( Not inches 22 m/m diameter )

    @pekpks7347@pekpks73477 ай бұрын

    • Go for it my friend

      @Mastermind-@Mastermind-6 ай бұрын

  • Excelente trabalho e muito conhecimento parabéns

    @invencoesecriacoescaseira@invencoesecriacoescaseira9 ай бұрын

    • obrigado meu amigo🙏👍💐

      @Mastermind-@Mastermind-9 ай бұрын

  • Bro i appreciate how clean you work ! Great job!

    @jasonbarnes3360@jasonbarnes33608 ай бұрын

    • Thanks for watching Thank you very much and I am glad that it was enjoyable for you, my good friend

      @Mastermind-@Mastermind-8 ай бұрын

  • Bardzo dobra robota!!!

    @tommec@tommec9 ай бұрын

    • 🙏🙏🙏💐

      @Mastermind-@Mastermind-9 ай бұрын

    • 709

      @NarinderSingh-bw9gv@NarinderSingh-bw9gv9 ай бұрын

    • Слышишь лях, а в где добрая работа??? Точность + километр -километр. .а цена 1 штуки 1 скудо.

      @KrugerdlyaMoisha-ce2xg@KrugerdlyaMoisha-ce2xg6 ай бұрын

  • Un artista!. Si señor

    @javiermaroto5529@javiermaroto55298 ай бұрын

    • 🙏💐🙏

      @Mastermind-@Mastermind-8 ай бұрын

  • Superb skills and hat off to someone’s that really deserve It.

    @mauriziograndi1750@mauriziograndi17507 ай бұрын

    • Thanks my dear friend

      @Mastermind-@Mastermind-6 ай бұрын

  • Good work. We shared this video on our homemade tools forum this week 😎

    @homemadetools@homemadetools9 ай бұрын

    • Wow, thanks🙏🙏💐💐

      @Mastermind-@Mastermind-9 ай бұрын

  • Hello, have a good time, don't be tired, thank you for your good video, it was very good

    @mrsnazgol5314@mrsnazgol53149 ай бұрын

    • Thank you! You too! سپاسگزارم سانازگل

      @Mastermind-@Mastermind-9 ай бұрын

  • Bonjour,quel beau travail. Très bien filmé. Mes respects 👍👍👍😉

    @lulubining5208@lulubining52089 ай бұрын

    • Merci mon bon ami et je suis si heureux que cela ait été agréable pour toi🙏🙏🙏💐

      @Mastermind-@Mastermind-9 ай бұрын

  • Gran Bel Lavoro da professionista e con stile. Complimenti sei Bravissimo.

    @enricodelre284@enricodelre2849 ай бұрын

    • Grazie mille mio buon amico🙏🙏🙏

      @Mastermind-@Mastermind-9 ай бұрын

  • Great job really! Only time I got was holding on to the part by hand during the drilling process. 🎉

    @elisancere3578@elisancere35784 ай бұрын

    • Worried*

      @elisancere3578@elisancere35784 ай бұрын

    • Glad it helped!👍

      @Mastermind-@Mastermind-4 ай бұрын

  • Buen trabajo aunque pensaba, sí, en el costo beneficio. Pero es un trabajo artesanal a costa de ingenio , paciencia y habilidad. Es una satisfacción para el que lo hace. Vaya mis felicitaciones para Master y gracias por compartir conocimientos.

    @Cesarlujan55@Cesarlujan55Ай бұрын

    • Gracias por tu valioso comentario, mi buen amigo, y me alegra mucho que lo hayas disfrutado.🙏🙏🙏👍❤️

      @Mastermind-@Mastermind-20 күн бұрын

  • Atelier propre, machines outil propre et enfin un travail effectué dans les règles de l’art. Je respecte et admire les personnes comme vous qui exécute des travaux frisant l’excellence, je remercie ceux qui vous ont transmis leur savoir et je ne doute pas une seconde que à votre tour un jour vous le transmettez à votre tour…… Cordialement

    @claudegillin8713@claudegillin87133 ай бұрын

    • Merci beaucoup mon cher ami et j'apprécie votre point de vue différent et j'espère que vous avez apprécié la vidéo🙏🙏🙏

      @Mastermind-@Mastermind-3 ай бұрын

  • Ficou muito bom!! Parabéns

    @RebobinadoraSaoFrancisco@RebobinadoraSaoFrancisco6 ай бұрын

    • Muito obrigado meu bom amigo

      @Mastermind-@Mastermind-6 ай бұрын

  • Genius!! The possibilites are endless!

    @googleuser2607@googleuser2607Ай бұрын

    • 🙏🙏🙏👍🌹

      @Mastermind-@Mastermind-20 күн бұрын

  • Very good idea, and better job ... i only ask how much oxygen was used, and how much would be instead cost a commercial tap ... ( of course not to deal with taps that are really "hard to find" on the market ... ). Note : a test with a blind bore would be much more relevant, as spiral taps are expecially designed for that type of holes ... Thank you very much in any case for your usefull lesson, i really appreciated both the heat treatments of common drills ...

    @alessandroandrenacci2372@alessandroandrenacci23725 ай бұрын

    • 🙏🙏🙏💐

      @Mastermind-@Mastermind-5 ай бұрын

  • Exelente me gusto la idea grasias por compartir

    @javiercalvo8031@javiercalvo80319 ай бұрын

    • Muchas gracias mi buen amigo y me alegro mucho que te haya gustado🙏💐

      @Mastermind-@Mastermind-9 ай бұрын

  • Instead of the Three Jaw Chuck, you should use an ER32 Collet for better grip and concentricity.

    @astridvallati4762@astridvallati47629 ай бұрын

    • buy us all one.

      @assyholey4224@assyholey42249 ай бұрын

    • @@assyholey4224 A mí que me compre un macho como ese, ya estoy conforme...

      @viejojorgge@viejojorgge9 ай бұрын

  • Nam știut ca din burghiu poate sa facă asa ceva tarod bravo meseriasule

    @ColiRuja-mg5zs@ColiRuja-mg5zs9 ай бұрын

    • multumesc prietene

      @Mastermind-@Mastermind-9 ай бұрын

  • Спасибо. Идея которая лежит на поверхности. Можно изготовить метчик с направляющей. Его иногда так не хватает.

    @silushkadebilnaya@silushkadebilnaya14 күн бұрын

  • Complimenti!!! bellissimo e perfetto lavoro👍👋 Un saluto da Roma

    @robertocentonze9653@robertocentonze96532 ай бұрын

    • Grazie e sono molto felice e onorato che ti sia piaciuto, mio ​​buon amico🙏🙏🙏👍❤️

      @Mastermind-@Mastermind-20 күн бұрын

  • Very Helpful and Informative video 👍✌️❤

    @MechanicAvenue@MechanicAvenueАй бұрын

    • Glad it was helpful!🙏🙏🙏👍⚘️

      @Mastermind-@Mastermind-20 күн бұрын

  • Nice 👍👍🤝 Dear friend so amazing🌹☺

    @masterQ20@masterQ209 ай бұрын

    • Thank you so much 👍🙏🙏💐

      @Mastermind-@Mastermind-9 ай бұрын

  • Sangat menakjubkan kawan. Hand trhead yang mantap

    @bimbim2000@bimbim20009 ай бұрын

    • terima kasih kawan🙏🙏💐

      @Mastermind-@Mastermind-9 ай бұрын

  • 4:03 which insert are you using for turning???

    @parikshitdeshpande7311@parikshitdeshpande731112 күн бұрын

  • Super jest to pomysł pozdrawiam serdecznie 👍👍👍👍🏻

    @andrzejporeda7281@andrzejporeda72816 ай бұрын

    • Dziękuję mój dobry przyjacielu i bardzo się cieszę, że Ci się podobało🙏💐

      @Mastermind-@Mastermind-6 ай бұрын

  • super good work !!!

    @towaker@towaker8 ай бұрын

    • Thanks a lot!🙏🙏💐

      @Mastermind-@Mastermind-8 ай бұрын

  • Parabéns pelo trabalho e pela organização e limpeza durante o trabalho.

    @donizetesiqueira-pezinho7621@donizetesiqueira-pezinho76219 ай бұрын

    • Obrigado, meu amigo Eu espero que você tenha gostado🙏

      @Mastermind-@Mastermind-9 ай бұрын

  • La pregunta es. Quien tornio las parte del primer torno creado ???

    @latinotvsa@latinotvsa9 ай бұрын

    • No te pillo

      @Mastermind-@Mastermind-9 ай бұрын

    • @@Mastermind- ósea quien hizo tornio las partes del primer tornó creado. Si no existia un torno

      @latinotvsa@latinotvsa9 ай бұрын

  • Well done that man.

    @philipdenner8504@philipdenner85049 ай бұрын

    • Thanks my dear friend👍💐

      @Mastermind-@Mastermind-9 ай бұрын

  • Very good idea.

    @joaopetrusdesouza5707@joaopetrusdesouza57079 ай бұрын

    • Many many thanks🙏💐

      @Mastermind-@Mastermind-9 ай бұрын

  • OLÁ. Gostei de ver. Acredito que o primeiro aquecimento foi para "temperar" a peça. A sugestão é a de um esfriamento mais lento colocando-a no mesmo recipiente porém envolta de grossa camada de "Carvão MINERAL". No final, a forma como foi feita a "CIMENTAÇÃO" é muito provável que a peça se torne 'QUEBRADIÇA". ABRAÇOS... Roberto Udo Krapf

    @robertoudokrapf453@robertoudokrapf4535 ай бұрын

    • Olá meu bom amigo Muito obrigado🙏🙏🙏💐

      @Mastermind-@Mastermind-4 ай бұрын

  • Grand Travail, bravo 👍

    @paulmacca3974@paulmacca39747 күн бұрын

  • отличный мастер молодец

    @eleddinabbasov6669@eleddinabbasov66699 ай бұрын

    • 🙏🙏💐

      @Mastermind-@Mastermind-9 ай бұрын

  • Just a quick question. Doesnt the reheating blunt the cutting edge of the tap?

    @barryvanwyk7467@barryvanwyk74679 ай бұрын

    • I don't think it has any effect, but to be sure, I resharpened the edges after reheating

      @Mastermind-@Mastermind-9 ай бұрын

    • no, he is now re-heat treating the tap as he annealed it at the start of the video.

      @glennschemitsch8341@glennschemitsch83419 ай бұрын

  • very good job,thx!

    @laszlohentes61@laszlohentes619 ай бұрын

    • Glad you liked it!🙏🙏🙏💐

      @Mastermind-@Mastermind-9 ай бұрын

  • Bom trabalho que fez com a broca quebrada, parabéns

    @jadae001@jadae0019 ай бұрын

    • Obrigado meu bom amigo e fico feliz que tenha gostado

      @Mastermind-@Mastermind-9 ай бұрын

  • I'm already subscribe from some previous ridiculous video I watched of yours. Love the innovations!

    @saytencushman3758@saytencushman37589 ай бұрын

    • 🙏👍💐

      @Mastermind-@Mastermind-9 ай бұрын

  • Muito bom excelente parabéns

    @user-yn2jx5qt6x@user-yn2jx5qt6x7 ай бұрын

    • Muito obrigado meu bom amigo

      @Mastermind-@Mastermind-6 ай бұрын

  • Now if you only had a twist drill that was left hand You could have the chips fall down Well done And I love the fact no crappy music Thanks

    @CMAenergy@CMAenergy9 ай бұрын

    • Thanks my friend🙏👍

      @Mastermind-@Mastermind-9 ай бұрын

  • Can an Acme hand thread tap be made in the same way? Would any modifications to this protocol be needed?

    @enigmaseth@enigmaseth6 ай бұрын

    • yes it will

      @Mastermind-@Mastermind-6 ай бұрын

  • Slick! Great video thumbs up.

    @craigsudman4556@craigsudman45569 ай бұрын

    • Thanks for the visit

      @Mastermind-@Mastermind-9 ай бұрын

  • 19:26 why this way? Use drill machine 18:25 for perfect coaxial hole.

    @helmut3356@helmut33569 ай бұрын

  • Jak ja dawno nie ostrzyłem noża oprócz przecinaków do plastiku

    @porcupinewspaniay5852@porcupinewspaniay585226 күн бұрын

  • Excelente trabajo🙏🤗

    @user-sz8vl1ej1z@user-sz8vl1ej1z2 ай бұрын

    • 🙏🙏👍🙏🌹

      @Mastermind-@Mastermind-20 күн бұрын

  • Schöne Arbeit, aber lohnt sich der Aufwand.

    @manfredgroma4608@manfredgroma4608Ай бұрын

    • 👍👍🙏🙏

      @Mastermind-@Mastermind-20 күн бұрын

  • When you just have many cool machines.))))

    @Ma_X64@Ma_X649 ай бұрын

    • And when you have great ideas and machining skills😉

      @Mastermind-@Mastermind-9 ай бұрын

    • @@Mastermind- Look at @Mehamozg. I'm shure you'll like it.

      @Ma_X64@Ma_X649 ай бұрын

    • I saw it and just👏👏👏👏👏

      @Mastermind-@Mastermind-9 ай бұрын

  • Nice work

    @petermcneill80@petermcneill809 ай бұрын

    • Thanks for the visit🙏🙏💐

      @Mastermind-@Mastermind-9 ай бұрын

  • muy bien para fabricar machos de roscas poco comunes parece una idea genial, para roscas comunes no merece mucho la pena acabo de compara un M11x1 por 4 euros( igual solo hace una rosca pero va a cumplir)

    @juancar2568@juancar25686 ай бұрын

  • That is my kind of recycling!!

    @victorreppeto7050@victorreppeto70509 ай бұрын

    • 👍👍👍💐

      @Mastermind-@Mastermind-9 ай бұрын

    • Sorry, not worthwhile at all. Btw, you should use grinding machine instead of lathe to make thread. HSS steel doesn't need oil as a cooling medium. Liquidifed Corbin dioxide can work.

      @quincylui95@quincylui959 ай бұрын

  • GOOD STUFF 👍 THANKYOU

    @renripari5514@renripari55146 ай бұрын

    • Glad you enjoyed it🙏💐

      @Mastermind-@Mastermind-5 ай бұрын

  • موبدع وعمل جيد جداً

    @user-rf3vo4rr2x@user-rf3vo4rr2xАй бұрын

    • 🙏🙏🙏👍

      @Mastermind-@Mastermind-20 күн бұрын

  • Compla ali na China, balatinho né?😂 Excellent job, congrats.👍👍

    @Seteclata@Seteclata9 ай бұрын

    • merci moninga na ngai👍💐

      @Mastermind-@Mastermind-9 ай бұрын

  • круто , но уж очень заморочено . 👍

    @user-cd7oq7yc6n@user-cd7oq7yc6n8 ай бұрын

  • Молодец! Работа на высоком уровне. Продолжайте повышать свои навыки.

    @vdovinandrey@vdovinandrey9 ай бұрын

    • 🙏🙏💐

      @Mastermind-@Mastermind-9 ай бұрын

    • Резьбу бы резать более полого на конус. Метчик будет так работать успешнее.

      @papa58857@papa588578 ай бұрын

    • Зачем заниматся целы день одним метчиком с очень низкой точностью, хуже китайских из 90х, если он стоит копейки, чисто хайпануть на восторженных дурачках, или если живёшь на северном полюсе в полной автономке.

      @KrugerdlyaMoisha-ce2xg@KrugerdlyaMoisha-ce2xg6 ай бұрын

  • Adamın dibisin kardeşim 🎉❤

    @hayatsanayi1238@hayatsanayi12389 ай бұрын

    • sağ ol, kanka Umarım eğlenmişsindir

      @Mastermind-@Mastermind-9 ай бұрын

    • @@Mastermind- hem eğlendim hem öğrendim eline sağlık

      @hayatsanayi1238@hayatsanayi12389 ай бұрын

  • Bellissimo lavoro

    @lucianoalberto7555@lucianoalberto7555Ай бұрын

    • Grazie e sono molto felice e orgoglioso di te, mio ​​buon amico

      @Mastermind-@Mastermind-20 күн бұрын

  • I enjoyed a lot and thanks

    @user-vj4fq7gq3f@user-vj4fq7gq3f6 ай бұрын

    • Glad you enjoyed it🙏💐

      @Mastermind-@Mastermind-6 ай бұрын

  • Bravo vrhunski projekat

    @bobansupergenije7512@bobansupergenije75129 ай бұрын

    • 🙏🙏🙏💐

      @Mastermind-@Mastermind-9 ай бұрын

  • Most TiN-coated drills are not real M2 or M3 HSS, so your tap is probably alloy. HSS is air-hardening, so it's very difficult to anneal.

    @Bob_Adkins@Bob_Adkins9 ай бұрын

    • HSS or Cast iron can be easily (not- really) Annealed by Submerging it into Limestone powder just after Reaching Red hot temp.

      @rameezsheikh7576@rameezsheikh75769 ай бұрын

    • Для HSS требуется температура закалки 1250 Цельсия. Это невозможно обеспечить газовой горелкой. Твердость будет маленькая.

      @VINOGRA@VINOGRA9 ай бұрын

    • This cannot be a cheap drill to start with,as some are just coated to make them look expensive.

      @glennschemitsch8341@glennschemitsch83419 ай бұрын

    • @@VINOGRA that is oxygen-acetylene torch which is up to 3200°C.

      @kieranh2005@kieranh20059 ай бұрын

    • @@kieranh2005 yes can reach those temps but this one was bearly turned on (still hot but not that hot)

      @arthurhuskins910@arthurhuskins9108 ай бұрын

  • 👍 brilliant!

    @James-fs4rn@James-fs4rn6 ай бұрын

    • Many many thanks my dear friend🙏💐

      @Mastermind-@Mastermind-6 ай бұрын

  • Nice work piece

    @josephmacuha3068@josephmacuha30689 ай бұрын

    • Thank you so much🙏👍💐

      @Mastermind-@Mastermind-9 ай бұрын

  • Toll gemacht … !

    @mighi68@mighi689 ай бұрын

    • Danke mein Freund🙏🙏🙏💐

      @Mastermind-@Mastermind-9 ай бұрын

  • The card is great, but the quality of your camera😢😢😢

    @user-xh7il8wf7b@user-xh7il8wf7b6 ай бұрын

  • Why you applied heat before machining the bit??

    @abdeljalilpr2033@abdeljalilpr20337 ай бұрын

    • For reversibility and softening of machining angle

      @Mastermind-@Mastermind-6 ай бұрын

  • Great teacher.

    @kiatthaitraditionalclinic9264@kiatthaitraditionalclinic92646 ай бұрын

    • Glad you think so🙏💐

      @Mastermind-@Mastermind-6 ай бұрын

  • Good work👍

    @chotuusian4127@chotuusian41279 ай бұрын

    • Thank you so much 🙏👍

      @Mastermind-@Mastermind-9 ай бұрын

  • How did you know how fast you need to rotate the piece and how fast to move the cutter in order to make the thread`?

    @ZorlacSkater@ZorlacSkater6 ай бұрын

    • No matter how hard the tool steels are, they are still harder than normal steels and must be machined at a relatively lower speed.

      @Mastermind-@Mastermind-5 ай бұрын

  • Nice job,👍👍👍👍👍👍👍👍

    @WayneCook306@WayneCook3066 ай бұрын

    • Many many thanks🙏💐

      @Mastermind-@Mastermind-6 ай бұрын

    • You're Welcome.@@Mastermind-

      @WayneCook306@WayneCook3066 ай бұрын

  • Bravo Bravo Türkiye İzmir selamlar ve abonelik 🎉

    @HayatHayat-yj8qn@HayatHayat-yj8qn9 ай бұрын

    • Merhaba değerli arkadaşım Eğlendiğine çok sevindim🙏💐

      @Mastermind-@Mastermind-9 ай бұрын

  • Muito bom!

    @edilsonmartins6653@edilsonmartins66539 ай бұрын

    • obrigado meu amigo🙏

      @Mastermind-@Mastermind-9 ай бұрын

    • 나사 작업후에 탭 열처리 안해도 됩니까?

      @taejin821@taejin8216 ай бұрын

  • If you tell me to like, I WONT!

    @mrdan2898@mrdan28986 ай бұрын

  • Super podoba mi się

    @krzysztofw3925@krzysztofw39259 ай бұрын

    • Dziękuję, przyjacielu🙏🙏👍💐

      @Mastermind-@Mastermind-9 ай бұрын

  • Very nice work

    @mohammadhafeezkhanraja4758@mohammadhafeezkhanraja47589 ай бұрын

    • Thanks a lot🙏💐

      @Mastermind-@Mastermind-9 ай бұрын

  • How much is the price? I like it

    @chungkhokamtouthang5509@chungkhokamtouthang55094 ай бұрын

    • Free for you my good friend and glad you enjoyed🙏🙏💐

      @Mastermind-@Mastermind-4 ай бұрын

  • Very nice mate.

    @markrainford1219@markrainford12199 ай бұрын

    • Thanks for the visit

      @Mastermind-@Mastermind-9 ай бұрын

  • Nice job sir

    @farhankhan-dh2tu@farhankhan-dh2tu9 ай бұрын

    • So nice of you🙏🙏💐

      @Mastermind-@Mastermind-9 ай бұрын

  • Eso está bien saber hacerlo , pero si iba a una tienda de metal mecánica, y lo compraba, se hubiese ahorrado todo ese trabajo y hubiese gastado mucho menos😅😅

    @vincenzociraso783@vincenzociraso783Ай бұрын

  • Excelente trabalho

    @JTelecom@JTelecomАй бұрын

    • 🙏🙏🙏👌❤️

      @Mastermind-@Mastermind-20 күн бұрын

  • Materiał zachartowany powinien być odpuszczony czyli jego twardość trochę się zmniejszy ale nie pęknie gdy przez nie uwagę spadnie, czy gwintowanie pójdzie trochę bokiem, lub inne sytłacje. Prosty sposób na chartowanie byłby taki jak zrobiłeś na początku. Grzanie jeśli możliwe całego elementu (najlepiej przez 1h) lub chociaż 30minut w szamot (cegły piecowe) i potem zachartować w całośći ale zostawić do czasu aż ostygnie w całośći. (Może w wodzie ale z dodatkiem soli (są osoby które dodają też sól do oleju ale efekt mi nie jest znany ??). Następnie czysty gwintownik wkładamy do piekarnika na 1h z tem 100⁰C (tu bywa różnie od metalu i odpuszczanie może być nawet w tem 250⁰C-ale jak dla mnie temperatura bezpieczna jest tem max 150⁰C. Tak naprawdę wszystko zależy od stali.) Czasami trzeba jeszcze raz włożyć do piekarnika po całkowitym ostygnięciu na kolejną 1h-100⁰C. Dobrym wyznacznikiem twardośći są koncówki (igły,szpilki wewnętrzne wtryskiwacza) i próba nabicia na główce małego punktu. Przy normalnym uderzeniu, głebokość punktu, lub uszkodzenie szpilki wew. wtrysku. (Sam czubek jest utwardzony . I nie polecałbym mocno bić młotkiem ,czy z boku gwintownika czy innego utwardzonego elementu). Na wpływ twardośći materiału ma też wpływ gaz jakim grzejemy materiał. ACETYLEN -powoduje że powierzchnia elementu staje się bardziej twarda !!!!!!!. Pozdrawiam

    @piotrwaalk705@piotrwaalk7054 ай бұрын

    • Dziękuję bardzo za dobre informacje, mój dobry przyjacielu🙏🙏🙏💐

      @Mastermind-@Mastermind-4 ай бұрын

    • @@Mastermind- ważne aby wymieniać się informacją ;)). Mam nadzieję. Że się przyda. Pozdrawiam i POWODZENIA 👍😉. I najlepszego na Te Święta 🎅🎅👝👝🍲🍲😀😀 i na nowy rok 🍾🍾🍻🥂🎉🎊☃️

      @piotrwaalk705@piotrwaalk7054 ай бұрын

    • 🙏🙏👍💐

      @Mastermind-@Mastermind-4 ай бұрын

  • Very Very good

    @jagjeetsingh8587@jagjeetsingh85878 ай бұрын

    • Thanks🙏💐

      @Mastermind-@Mastermind-8 ай бұрын

  • Все прекрасно. Мастер рукастый, но вопрос зачем? Метчик можно купить, а не тратить на это весь день

    @user-vj7cn5hk9v@user-vj7cn5hk9v5 ай бұрын

    • Работа занимает от силы пару часов, вполне адекватное решение, если нет доступного магазина инструментов.

      @user-hc6gb9oq9m@user-hc6gb9oq9m6 күн бұрын

  • perfect!!!

    @sugarmarmelate1952@sugarmarmelate19525 ай бұрын

    • 🙏🙏🙏💐

      @Mastermind-@Mastermind-5 ай бұрын

  • Mũi tê rô... mới tê rô 1 lần cùn răng rồi ak

    @QuangNguyen-up2xo@QuangNguyen-up2xo6 ай бұрын
KZhead