Round Pipe Bending Mistake // Round Pipe Bending Tricks
2022 ж. 4 Ақп.
1 448 519 Рет қаралды
Round Pipe Bending Mistake // Round Pipe Bending Tricks
How to prevent thin stainless steel pipe from being compressed
metal and steel pipe wrinkle problem solve
#mdkhan
#diy
#welding
Great idea ! I worked in a metal forming shop, we used a special metal called "KIRK SITE", it is like Aluminum, except it melts at 165. degrees Fahrenheit, we would heat it then pour it into tube or pipe then make the bends. Mostly in STAINLESS STEEL, then heat the piece and the KIRK-SITE would run out and the piece would be smooth without defects. Great Video. Greetings from Los Angeles. California 🇺🇸
Я заливал воду замораживал ,гнул ,потом лёд растает и вода выльется из любой конфигурации.
Thank you for this: This was amazing to me, so I did some research - : Kirksite melts at 395°C (745°F), it looks incredibly useful - The stuff you were using appears as though it could have been Cerro Bend which melts at just 70°C (158°F) ?
Have you ever tried sand? It's easy and efficient
સરસ સરળ અને ઉપયોગી આજ રીતે પ્લાસ્કિટ પાઇપ માં માટી નાખી બહાર થી હોટ ઘન વડે સરળ તાથી બેન્ડ કરી શકાય છે આભાર
Thank You very much MD KHAN!! May God give you more blessing!! ❤️❤️
Wwwwwoooowww !!! So amazing 😍 I haven't seen anything like it. You guys ROCK!
WOOO es una super máquina 🖒 podrías hacer un tutorial de como construirlo porfavor. Saludos de LIMA/ Perú 🇵🇪
kzhead.info/sun/md2dqaini2ivjHA/bejne.html
Muy buen consejo utilizar arena para que no se desfigure el tubo... desde Colombia
I will remember this cool trick for sure! Thanks!
First tube was thin wall aluminum. Second tube was thicker wall stainless. (You can tell by the color of the weld) I call BS using sand without capping the ends TIGHT.
No this is working...i used it before
You taking something that works and dismissing it. The point of the video is to use sand to avoid the example given.
Muchas gracias Maestro! 🙏
Slick. I've watched something like this done with pvc pipe.
¡Excelente trabajo MD KHAN! Saludos
Good job; congratulations.
Great video, thanks for sharing #mrnams
Bravo! Great!
Nice thank you very much👍👍👍
первая труба была с тонкой стенкой ) а у второй стенка толще) и согнуть ее без вмятин проще ) засыпь песок в первую трубу и посмотрим на результат)))))))))))
Tnx sa info sir
Bhai aap apna video kon sa category me upload करते हैं
Very good - thanks
Какая толщина стенки трубы?
Gracias por el video al fin voy a doblar tubos correctamente....... Esa dobladora me gusta..... Si no es mucho pedirles detalles o planos.... Gracias😢
Bhia circle ka size kitna hai
Kitne gaje Ka pipe hai
Bon travail!
Will any sand do?
It would be better if you use a pipe bending spring inside it so you can pull it out after you have done it on the bending machine you have olé.
Прекрасно !!!👍
Nice very 👍🏻
Good job keep safe stay connected
kzhead.info/sun/md2dqaini2ivjHA/bejne.html
great idea
Si tienes. Que hacer 100 tubos te lleva meses con ese sistema buena esa felicidades
Can we replace the sand that you put in the tube with mandrel
No because the mandrel won't bend.
Add grease to the follower and it should improve a little
Good ideas
Genius
Nice
Great
Awesome
Cambie la curvadora, trabaje con una bien diseñada y nunca deformo un tubo sin añadir arena .en produccion en masa no puedes estar perdiendo tiempo en taponar con trapos apretar la arena etc. Osea mala la maquina ademas esta mui lejos el punto de apollo, y pierdes tiempo en amordasar el tubo .lo digo con 5 años de experiencia trabajando con curvadoras curvadoras
Which companies pipe bender you are using?
Pour plier le tube de cette façon, il vous faut une olive,pour que le tube ne se casse pas, essayez avec une olive
Geniuses
Super
Machine ka naam kya hai
Hi, Why you do not use Mandrel for tube bending? it's very simple.
They can't even afford shoes is probably why.
@@iguanapete3809 mandrel is very simple and chip, we need a round rod inside tube
How do you keep your white cloth so clean?
First you must wear the shirt for two to 12 months straight, this will allow your bodies natural body odour to linger and survive long after you remove it for washing[your body not the shirt] remember you didn't wear it months straight to wash out those built up grease stains, next find a third world country so dirty no one notices your stench or filth, once you have gained access and blended in with natives you begin to whiten you clothes[note the joke of using plural of cloth as we all know that one shirt is it] now the whitening begins, role in lots of dusty environments usually asbestos is good as impregnates your rags you will become more or less fire proof, then the final stage is to literally burn all that grease and fat out of the clothes as you enjoy the once a year bath in the nearest river/sewer and bingo fire proof clean rags which no one dares steals as the stench is your own unique flavour. Enjoy.
Pin kro bhai 😊😊
good to know
Best bending
Fst like🤗🥰
Если немного доработать приспособление то можно без песка обойтись.
Não vem que não tem, o primeiro cano era muito mais fino que o segundo, quero ver ele fazer curva no primeiro mesmo com areia
Actually the tubes were already replaced by one with a larger thickness.
Красота, вершина слесарного мастерства!
I wonder if compressed air would work the same
It would not work the same. Gas compresses
Офигенный инструмент - все из кривой, приваренной на соплях арматуры, на второй ролик денег не хватило.
The pipe which came out with fine bended is thicker than the previous one which was very thin but the guy did not show the thickness of the pipe but for first pipe he showed that it was thin
you didnt get the point of this video? He showed you how to properly bend a thin pipe. And thats how you supposed to do it.
@@buduchildno, you
👍
Goodd
😊😊😊😊
这个我以前弯酒管永的设备
Super Arbeit 😂😂😂
Sand takes time, could easily convert this to a mandrel bender and be able to make bends with half the radius.
Mashallah 💞💞
يوجد افضل من هذا
सिल्वर पाइप की मोच कसे निकले
We need wheel of dye
If in doubt pack the pipe with sand first...
OMG Are you serious? I can't believe what I've seen! Black shoes and white socks? 😱
👍× 100000000
'smooth bend I'd grease up all the moving parts.
Bahi ap Pakistan main dilevrey Kar sktay hain
Kia chahye apko?
Ye machine chahye?
По мне так на 2.33 минуте лучше трубка загнулась, чем с песком!
Kha se ho aap bhai
Jabalpur MP
@@MDKHAN-9907 ओके भाई
İlk boru alüminyum ikinci boru paslanmaz birde aparatınız eski çağlardan kalma .benim kendi imkânımla yaptığım aparat pürüzsüz ce büküyorum paslanmaz ve normal çelik.
Why did you use the wrong diameter of bending device? No wonder the pipe is folding like this…
Не правильно собрана. Можно без песка
Segala pake pasir ..bikin rumit aja ..ngak praktis...alat kurang mantap..
Getting the rags and sand out is even more difficult. A better way is to heat the metal red hot then bend it. Much better method
Hola
Hola
Pahele vala pipe bahot halka tha 😄😄😄
😀😀😀 #mrnams
Use bol medarl
You need to fill sand to be successful, that is because your technology is not good, so how much time will be wasted. You don’t need to fill sand, just change the shape of the mold groove and you can bend successfully.
I don't understand how that worked. When I use sand I have to crimp the end of the tube off or it'll simply push the sand out of the way. This is for things like a brake line or gasoline line and making those tight corners.
Apparently you missed the part where he tamped the sand down after plugging the ends with rags. It does work. I have also filled them with water and froze them.
@@donmunro144 I didn't miss that part. It doesn't work. I tamped it down with as much pressure as I can put on a 1/4" pipe full of sand. Even using a #5 hammer to drive a rod into it. I tried it dry, wet, it didn't matter. It simply pushed it out when I bent it. Rags won't hold it and I'm fairly sure they didn't freeze it given where they are and the equipment they're using. Maybe it's different with a big relatively thin pipe vs a small pipe. Even with a crimped end it still has to be a very good crimp or it'll push that out as well. That is, I can't simply smash it together with a hammer for example. I have to fold it over. That's why I'm asking here. I'm trying to find someone that has done it without crimping it. I have a lot more brake line to make soon and that pipe is expensive. I'd love to know how GM, Ford, Toyota, etc do it in the factory. I know it's done by machine. However, they still have to worry about it kinking. Maybe they can get away with heating it. The pipe I can buy has an external coating that is very good. However, I don't think it can take the heat needed to bend it.
@Robert Thomas when I'm doing brakelines i use a pliers style bender for 3/16 & 1/4 in line. Then I have a die and shoe bender for up to 3/8 line. Anything bigger i normally fill the line with water and freeze it. Then bend it.
@@robertthomas5906 ... I do brake lines all the time, and yeah, I do occasionally kink one. The key to NOT kinking is holding pressure so the line stays in the groove of the bending tool. Depending on where the bend needs to be, sometimes it's better to put your bender in a vice so you have two hands to keep the work in the right place. In recent years I have switched to the coper / nickel variety line. So much easier to work with. BTW, I concentrate on the actual bends and if they don't line up quite right you can twist the tubing for a better fit. That's where the new stuff shines. Hint: remove the old line, place in on the bench, then use that for your template. If the line is more that 3-4 ft long make it in two pieces and add a union where it's easy to reach. (thinking about those GM lines along the frame rail) I usually do from the rear to the middle, and from the front to the middle, then do the union where they meet. (where you have room to work)
The radius of the bend should be at least 6x the diameter of your tubing to prevent kinks. I do brake lines and fuel lines all the time using a beer bottle. It gets you a variety of radius to choose from at the bottom of the bottle and along the tapered neck. Move the bottle along the tubing as you bend so you are bending a little in each spot. Use 1 hand on each side of the bottle holding the tubing with your 2 thumbs pushing on the bottle. No need for sand or special tools. Dont put sand in brake lines anyway
Are Naas he kar daya katye
You gotta fill it up with sand.
🏴☠️🏴☠️🏴☠️
牛
Nadar send karo
Pehele 22 gej phi 16gej
Or you can try filling it with sand
Yas
15+15=25
Ye 75 gaje ka pipe hai 😂😂
это для толсто стенного мать вашу
Samjga
Дикари "изобрели" трубогиб
Zonk 🤣
kalokohan, minipis yung unang tubo, yung pangalawa ay makapal at stainless pa
That first piece of tube was simply too thin to bend. The second piece was better. Sand filling helps but the stretch weakens the tube bif time. IF the end was not clamped so hard it would have bent a bit nicer
Pack sand in it before bending
He did.
Pagla .... boycott
What a waste of time. With proper tool you can bend even 0.45mm thick tubes without shrink. We are doing it in hundreds daily