Restoration giant subwoofer system // Restore 2000W subwoofer
2023 ж. 14 Қыр.
1 028 217 Рет қаралды
Thanks for watching, subscribe & share!
Restoration giant subwoofer system // Restore 2000W subwoofer
#mr_electricity #restoration #speakers
► Subscribe to channel: / mrelectricity1111
Please give me your opinion. Where is not good Let me improve.
------------------------------------------
Thank you for watching the video. please support me. Thanks you very much. love everyone.
вроде руки из правильного места растут, но есть несколько вопросов... первое - зачем пропитывать диффузор??? второе - стенки ящика надо делать в три раза толще!!! если хотите 2 kW снять, третье - трансформатор ватт 800 не более... так что 2 kW не получите. четвертое- без активного охлаждения ваши транзисторы стрельнут ровно через полчаса!!! пятое - на хрена щель????? у вас ЗЯ с фазоинвертором... кроме треска корпуса ни чего не слышно, столько трудов и в мусорку.
У них провод сопротивлением больше , так что с малым железом они получают мощность в разы больше. Посмотрите на трансформатор от микроволновки. А он почти два киловатта.
И ещё. Советский ватт, - это максимальная мощность динамика, при которой ещё практически нет искажений звука. Иностранный ватт, - это такая мощность динамика, при которой он разрушается за час. Точно не помню, но иностранный ватт раз в пять завышен по сравнению с советским. Китайский "перестроечный" ватт - мощность, разрушающая динамик за 3 секунды. Завышена по сравнению с советским ваттом раз в 50-100.
Это Бандпасс
Vendo esse vídeo de reforma do alto-falante, além da montagem da caixa amplificada, e um outro de conserto e restauração de um amplificador, me lembrei dos meus tempos de bancada, quando eu era mais jovem....trabalhei muito com reparos de equipamentos de áudio diversos e reformas de alto-falantes....Você só consegue fazer um trabalho desses se tiver paz e sossego, sem ninguém pra perturbar, pedir sua atenção ou te cobrando algo...até a chuva e som dela mostram a paz desse lugar pra se trabalhar...excelente vídeo...me trouxe boas lembranças...
A pior coisa que tem é da gente está se dedicando a algo e vem uns pra azucrinar nos ouvidos da gente!
About time for a new cutter in the router!
Very impressive!
The rebuild is very nice. The sound is wierd... I think the mic was swamped with to much sound?? If you treat the cone with a fluid and the cone becomes heavier you alter the moving mass from the unit and the Fs from the speaker. Did you account for that??
His mic and KZhead playback equalization don’t do justice to the sound.
I respect your efforts but eventually Sounds like Chinese Frying pan and Pot
Frying pans sounds better ...
The coil was put in bottomed out. Got to have equal distance centered on motor for linear excursion.
i heard it popping
The black glue around the coil to cone join is often softened by acetone, but that looks like a JBL in which case the most likely solvent is naptha (lighter fluid) Nice speaker. Well worth rebuilding.
Not a JBL. While having the same basket JBL doesn't have this cone or motor on their 18s
Wow that was a cool video great job
Para escuchar guarachas santiagueñas hasta el amanecer en navidad hasta año nuevo, genial man...
Начал просмотр с середины. Подумал, что будку кобелю на зиму строит, а оно вон что оказывается☺. Кстати, а у них вообще есть собаки?
مشاءالله تبارك الرحمن
Такой дома включиш крышу поднимет👍👍👍
Interesting build, with a bandpass enclosure. I would have went with a transmission line, and pushed it into the deep bass territory, just for fun :D
The editing to show the storm to explain the rain was brilliant. Keeping the story consistent so that we don't get thrown out of the "pocket." Thanks for the detail work!
I’ve watched you restore junk this ain’t so much junk but still ..Great job
i always reinforced the rim of the speaker outer cone with a few coats ov PVA wood glue.as i play a lot of dub bass n it needs reinforcing...just a thought...great vid,bought back memories of building me cabs back in the days
Nice work, but the heat sink will rattle, not fastened.
Great work interesting style woofer set up with built in amplifier
Vc conserta e vende
Hi, i'm from Brazil...I lke this channel very much... Congratulations and thanks.
Congratulate at your work 😎
He is highly skilled in speaker restoration Dịch
Excellent job.
Nice video, but you're really messing with my OCD at 6:44 when you almost did the cross pattern tightening, but stopped half way xD
very nice work. not a fun of box texture. you should have raised the coil a bit. also fasten the heatsink and reverse the on/off switch.
I also liked the rain on 10:30 and in the background!
I like you and profesional and I have subscribe. I am to Indonesia 🇮🇩.
Great if you like uninformative, boring videos with no narration.
You fu*ked up English
Great job Sounds Great.
You have to weld even the 2 giant condensators !
When i first saw it i was thinking my 15 looks pretty damn simlar wtf are you talking about.. then you measured it 😂😂 holy crow!
great job. perfect I would like to know the design of the box. Could you give me the measurements?
😊😊😊😊😊😊😊😊😊
`It is a great looking piece of kit and your craftsmanship is top notch,however.......lol I wouldnt put that piece in the front with the slot because I think it would cut off the really low long wave forms bigger than the hole.Most good designs offer an unobstructed path for low/large waves. the other slot is fine its just putting out the "backstroke" of the box. nice bit of kit tho!!!!
Bonjour de la France Mr Electricité.......... Très beau travail, mais attention la bobine mobile est trop basse, ça va taper dans le fond de l'entrefer...............
YO!! @ 7:15 - You REALLY NEED TO SHARPEN THAT ROUTER BIT!!!
I would have made it 4th order. Instead of that front slot. I would seal it
Вот откуда на aliexpress появляются акустические системы. Секрет раскрыт!
VERY LOW MASS GLUE, MAYBE SOME TYPE OF ACETONE ? AS REMOVER ?
Nice time to do the job inside or under a cover when raining! The rain is nice!
It looks great and you did a great job making that subwoofer I really appreciate your talent and ingenuity! Today I learned from you. really smart,
Perfect work
Nice idear. But not efficient. Same System like Electro voice in the earlier 90s. Better build 3 reflex enclosures and stacking. 8db more!!!👍👍🇩🇪
WOW!!! Amazing 🙌Work🙌🎶🔊
I have built loads of disco speaker boxes in the past. I had forgotten how much effort they take.
What's the amplifier model that you installed inside the woofer?
Indonesia bagian Jawa Timur hadir lhurrr
Wow a stomping subwoofer restoration
i like the screw holder
Don't worry about the quality, as long as it looks nice...
Ive experience also replacing speaker cone but didn't try assembling subwoofer but it much better if the hole youve made for exhaust of air must be circular and alike to the size of magnet so that the sound is pure bouncy rather than cracky.
С 80-ти вольт ага, два киловатта, конечно 😂
Buenas tardes que líquido usas para despegar tan rápido los conos de las bocinas
Good job but I will like to know the system brand or model. Thanks
Box speaker nta mantap sob...❤
Super.....
TOP Parabéns
Nice, but I hope you did not buy the power transistor and big capacitors in china, you could have a bad surprise soon.
Qual o nome desse produto gostaria de saber por gentileza
nice Job very good thx for your Video i like it
Very good 👏🏿👏🏿👏🏿👏🏿👏🏿
Great job !!! Well done !!!
most demanding video form mr electricity. This type video i need bro
Well done, great video 💪🏻😀
nice work
Exelente,, Felicidades,
Splendid!
Are you shure it's a subwoofer? Looks more like a wideband loudspeaker for concerts - short magnet with ability to take it apart
You build some very nice speaker boxes! I don't care what people say about you!
Усилитель ватт 200?))
As long as that copper coil is ok.Thats the main part needed!
Terrific 💯 PERCENT Job with that sub woofer build I really appreciate your talent and skill craftship Wow that is some high-quality skills you have to make that subwoofer If you were to sell that subwoofer how much would you sell that type of subwoofer Great job 👍👌😊
Bom dia valeu 👍 muito bom gostei
Great job💪👍👏😁
Very good👏👏👏👏👏
Котушка установлена неправильно. Он сильно утопил ее а нужно замерять толщину железа и выводить под железом и над железом на одинаковую высоту. По звуку кажется что котущка бьет в заднюю стенку магнитной системы
let's think about cleaning....soda blasting or sand ?.....I'm just giving you a hint....great as always:).......ps.Much faster!!!
Người Việt Nam mà làm KZhead hay nè
What is the name of the music? It can’t hear so clearly the music because it sound a low frequency bass.
Show muito toop
Nabangit mo sir na di ka nagamit ng monitor out what if may acoustic band ka pwede na yan di ba. if needed ng monitor may effects send to monitor ba yan?
Przepiękne jest ten stary zabytkowy głośnik odrestaurowany pozdrawiam serdecznie 👍👍👍👍👍
Excellent!!! Just one question: what kind of liquid do you use to remove parts such as seals, suspension, diaphragm, etc...? and what type of glue do you use for reassembly?? Thank you
No fan to cool of radiator? It will get hot 🔥🔥
Only thing missing is a voice to the video.
Um grande ❤
Alguém saberia dizer qual foi a tinta utilizada com a pistola para criar aquela aparência de bolhas na pintura? Would anyone know what paint was used with the gun to create that appearance of bubbles in the paint?
im watching and like ❤
It sounds very good, is it a 3rd order band pass design?
Awesome vidio❤❤❤❤❤❤❤❤
I feel a lot better about my router skills now.
QUE ESPETÁCULO DE HABILIDADE E SABEDORIA!
You got the on-off switch upside down. Start over again.
"Please give me your opinion. Where is not good Let me improve." It's very wise position.
My dad has a pair of woofers that look like this, legand has it that I sat in them when I was a baby! I guess that was a mistake that my dad only made once!😄😄😄
Maşallah cok iyi oldu
What preparation do you use to remove the membrane and spring? Please help... Regards
Membrane...spring?. How about surround, dust cap and spider? He either used acetone (like nail polish remover) or naptha (lighter fluid), depending on the type of glue.
Перед покраской металлических деталей их грунтуют
U r the heeeeero..❤
what solution did you use to undo it?
Seharusnya finishing memakai meja putar