How to make a one-way hydraulic jack
2024 ж. 10 Ақп.
210 247 Рет қаралды
#hydraulic #jokes #turning
how to make a one-way hydraulic jack
This hydraulic jack is a part of the spring bending device that can withstand very strong pressure
_____________________________________________________
• Steel turning:Steel ro...
____________________________
• How to make a square b...
_____________________________
• Square screw thread:(C...
_____________________________________________________
youtube.com/@MADtechnic?si=yv...
_________________________
#machine
#turning
#roller
#screw_thread
#Hydraulic
Nice
Youare an ace machinist and a great welder. Keep it going man. 👍👍👍
Thank you for motivating me. Wait for my next videos
Thank you for motivating me to wait for my next videos
Nice build. Hope you add a few more bolts on the top flange!
This is a part of another device that you will see how to make in the next ten days
This flange keeps the balance of the shaft in the center, there is no other pressure on it and the piston of the shaft does not reach it
Good work!
Thank you❤️🙏
It's great when the weld stag just peels off on its own.👍👍😀
Thank you🙏❤️
How high pressure oil will seal between ram and top cylinder cover.
This jack is one-way and the oil is in the upper part of the piston and pushes the piston down.
This hydraulic jack is used in a device that I will post a full video of in the next 10 days, subscribe right to see it.
nice stick welding proper old school job
Thank you, 👍
good job 👍
Thankfnl🙏
There are a lot of missing things like oil seals on top flange and bolts in it . And from where is the oil will exit
This jack is one-way, it comes down from the top with oil pressure, but a spring is used to come up. Subscribe me. In seven days, I will show you how to make a complete device that uses this jack.
U need more 4 more screws hole so it can withstand the pressure when press. Your gland head needed a WIPER seal so dust will not go in the cylinder. Your next design the piston should be more thicker with added WEAR RING seal. Good start to design own cylinder
Watch my last video. This jack is used in the device and the piston never reaches down to this flange. All you need to do is keep the shaft balanced in the center.
The oil pressure flows above the piston, not below. When the pump is pressed, the piston comes down, but a spring is used to return it, which you can see in my last video.
It is clear that you are a skilled craftsman and you know hydraulic and jack systems. I will be happy to hear such comments from you. Thank you.❤️ms🙏
Братан ты без страшный 😮
Am I scary or is it my job?
laik,verbal din partea mea ! (ma feresc de numarul care urmeaza )
I didn't understand that the translation doesn't translate, you can write in English
sory...@@MADtechnic
🙏❤️
Nigdy nie używaj gumowanych rękawiczek przy toczeniu bo napewno urwie ci dłoń pozdrawiam .
Zgadzam się z Twoimi słowami.To jest Iran.W krajach trzeciego świata nie przestrzega się bezpieczeństwa
Bạn lắp seal - oring chắc chắn sẽ bị rò rỉ!!!
Hello, this jack is one-way and the oil pressure flows behind the piston, and a spring is used to return the piston, and the bottom page is only for the balance of the jack shaft. You can see the use of this jack in the device that I posted the video
Top flange will fly some time😂
In seven days, I will upload the video of the complete construction of the device in which this jack is used, and you will see what pressure this jack can withstand.💪
@@MADtechnic i wish you luck my bro But i have long years experience with hydraulic presses and jacks i highly recommend to make the back flange like bolt thread it at least 1/3 of the cylinder length beside o ring at the top of the flange this way you well be safe more. Thank you for your video
Your opinion is correct, but about double-sided jacks, which are usually made of cast iron
Because the material of the piston and the shaft are both steel and it welds well, they are separated into one piece and the oil flows only on top of the piston, the oil pressure is directly on the shaft. I have been making this type of jack for fifteen years and it does not break.
@@MADtechnic all respect
Sir you not added any mouth seal so definitely there is oil leak in this cylinder in mouth
This jack is one-way, and the oil pressure to lower the piston flows only behind the piston, a spring is used to retract the piston inside, and the oil does not flow under it.
The use of this jack in the spring bending device is shown in the next video. You can easily see the function of this jack.
I don't have a lathe. Could I use a screwdriver 🪛?
No 🤣😁
@@MADtechnic well, thanks 🙏 for the video and showing what you can do.
These parts are part of the device that I will post a complete video of in the coming days
Ay mi hermano asta los huevos se me arrugan lijando interiores con guantes y manga larga ten cuidado usa un palo de escoba asle una ranura con la segueta y mete la lija si te jala o se te enrreda la lija no pasa nada pero con la mano te la giraen un atoron ya vivi esa acción con un amigo ,por meter la mano en un tubo
I agree that it is you who say that this work is dangerous, safety is not observed in my country👍🙏
Eso no sirve el propósito es Ber q lo q se ISO funcione pero eso no sirvió
I did not catch
In ten days, you will see that the device that uses this jack is working. These last four videos of mine are part of the device that I will show you how to make completely in the coming days.
Todo bien, pero el embolo tiene que ser mas robusto la pared de carga. a las 20 Ton. se puede acampanar.
It is true about the pistons that are made of cast iron and are attached to the shaft with flanges and screws, but the material of this piston is steel and it is welded to the shaft and it becomes one piece.
@@carlosramirez-cp5ni Check out my latest video, you can see the construction of the device that this jack is used in, how it withstands a lot of pressure.
Nice
Thank you🙏❤️