7 Segment Display Counter 0 to 9 using 4026 IC by INVENTIVE TECHNICAL SUPPORT
I have made a project which is Analog Counter 0 to 9 using 4026 IC with 7 segment display.This Circuit Works as a 7 segment Decoder. Please SUBSCRIBE to my channel for more information about Electronics Project.
This circuit can be easily made at home. You can made it too. It take some component to make it which I used.
1. Bradeboard
2. Some Jumper Wire
3. 4026 IC
4. 2 Push Buttan
5. 10 K Resistor (3 Pcs)
6. 330 Ohm resistor
7. 680 Ohm Resistor
8. 7 Segment Common Cathod Display (CC)
9. 9V Battery
10. Battery Clip
11. Blue LED (5 mm)
12. Red LED (5mm)
Please SUBSCRIBE to my Channel (INVENTIVE TECHNICAL DUPPORT)
and follow me into my social accounts given bilow.
Thanks for watching this Video.
Circuit Diagram : drive.google.com/file/d/1qZvG...
Please Watch this video and Support Me
1. 555 Timer IC Blinking LED Astable Multivibrator : • 555 Timer IC Blinking ...
2. Auto On Time Delay Circuit Using 555 Timer IC : • Auto On Time Delay Cir...
Facebook : / pallab.sarka. .
Instagram : / _its_015
Song: Erik Lund - Summertime (Vlog No Copyright Music)
Music promoted by Vlog No Copyright Music.
Video Link: • Video
Amazing, thank you, great content for my who is learning this myself
Thank You so much 🤗🤗
Thank you very much!
Welcome 🤗
mantapp
Very good
Thank you
this is 70s years technology
I know, but it's the basics that never change. 🤗 Thank You 🙏🙏😊😊
😅😅😅😅😅well information good show 😅😅😅
Thank You 🙏🙏
Hi, Is there any other IC that can be used with the 4026 to make up/down?
No sir, there is no any IC that can be used with the 4026 to make up/down counter. 4026 IC is only for Up Counter. But there is another IC that can be used to Up/Down Counter. I'll Upload a video. Please Subscribe to my channel for this type of Information about Electronics and Electrical
hello sir, is it possible to use a switch that can like activate and starts counting and then you can pause it while the other switch is only for reset. i am making a stopwatch and not sure what kind of switch and other components i should use.
I'll upload a video about Stopwatch.
Can I use LDR instead oof switch with this?
Yes, you can use LDR instead of switch.
how to make 2-digit for displaying 12-hour clock? (0 to 12)
I will upload a video about 12 hour countour
How to drive decimal point so it turns off on 10??
I think it's not Possible without Microcontroller.
can u get it to count down, too?
The CD 4026 IC is commonly used as a decimal counter, and it can count only Up Count. I'll upload a video about Up and Down Counter.
sir, can you show me to make a 4-digit digital counter?
Ok sir ji, I'll upload a video about 4 digit digital counter
@@its015 OK, thank you, sir.. please guide me with the schematic, sir
Is there is possible to reset as a downcounter
No 4026 IC is only for UP Counter
can it be done with two 4026?
@@olsihack Yes, Counting from 00 to 99 can be done using two 4026 IC
3v denna barida
I can't Understand what you mean 🤔
auto counter 기능이 없는 게 아쉽네.
kzhead.info/sun/ZMWKYNpubIynaX0/bejne.html Auto Counter function.
It is not working
This is not supposed to happen. Please recheck.
@@its015 my ic is 846PR7KE4 cd4026 ic is it the prblm?
@@its015Plz reply fast
@@sreelakshmik6394 CD4026 is Correct IC.
IC pin 16, and 3 goes to VCC And IC Pin 15, 8 and 2 goes to Ground. A PullDown Resistor connect to IC pin 1. Resistor value 10 to 100 Kilo Ohm