MOD 12 Hour Clock using 4026 IC Simulation Circuit By INVENTIVE TECHNICAL SUPPORT
I have made a project which is MOD 12 Hour Clock using Six 4026 IC , 555 timer IC and Six 7 segment display (Common Cathod).This Circuit Works as 12 Hour Clock Simulation. In the next video I'll made 00 to 59 Counter , 00 to 11 Counter, 00 to 23 Counter, Pure 1hz Clock Friquency.
If you like to see my video then Please SUBSCRIBE to my channel, Comment for more information about Electronics Project.
This circuit can be easily made at home. You can made it too. It take some component to make it which I used.
1. Six 7 Segment Display
2. Six 4026 IC
3. 555 Timer IC
4. 330 Ohm Resistor
5. 1 K Resistor
6. 10 K Resistor
5. 1N 4007 Diod
6. 25V 100uF Capacitor
7. BC 547 Transistor
8. Push Button
9. Red LED (5 mm)
this is Software Based Circuit Simulation, In the Next I'll Upload Bradeboard Circuit part by part.
Please SUBSCRIBE to my Channel (INVENTIVE TECHNICAL SUPPORT)
and follow me into my social accounts given bilow.
Thanks for watching this Video.
Circuit Diagram : drive.google.com/file/d/1J0Uy...
Astable Multivibrator :- 555 Timer IC Blinking LED Astable Multivibrator : • 555 Timer IC Blinking ...
1. 555 Timer IC Blinking LED Astable Multivibrator : • 555 Timer IC Blinking ...
2. Auto On Time Delay Circuit Using 555 Timer IC : • Auto On Time Delay Cir...
Facebook : / pallab.sarkar.378
Instagram : / _its_015
Song: Erik Lund - Summertime (Vlog No Copyright Music)
Music promoted by Vlog No Copyright Music.
Video Link: • Video
Thanks a Lot
Welcome 🙏
There is a problem. It's not display 12 in hours segments, How it display 12.
@@arexperiments. kzhead.info/sun/dcuhhKqSnZ6dZq8/bejne.html
Thank you for doing this circuit, can i ask why there are 330 ohm resistors always on the first digit but they aren't on the second digit? Sorry for this question but it's my first time using these IC's. Thanks!
I have installed 330 Ohm Resistor in this circuit for 7 Segment Display LED Protection. In 1st Digit I put 330 Ohm Resistor in Common pin and 2nd digit I put 330 for data pin. 🙏🙏
Hello can i ask what circuit simulator did you use? I want to try something with this awesome circuit before ill make a pcb thanks!
I used Proteus 8.6 simulation software .
Good work. But I am struggling to read the schematics. I went through the description to see if there is a link to download the more visible one like you always do but I didn't see. Hope to see the link soon. Your works are clean
Thank you sir, thank you so much. This video is for trailer only. in the next I'll upload this clock circuit part by part with circuit diagram.
Circuit is good but one problem time is not correct.
yes , you are Right time is not currect but if you want to fix the timing then change the pulse generating circuit. You can use 4060 IC instead of 555 Timer IC. How to generate 1 Hz Clock Pulse : kzhead.info/sun/Y6uqn9Ccop-dhaM/bejne.htmlsi=QdVT8DrhAGraRpsd
In your ckt diagram do we need the ic 4026 pin no 16 to be connected to +ve you have not shown this
This is not a real circuit, it is a simulation circuit, so there is no VCC and ground connection. 16 pin of 4026 IC is VCC and 8 pin is Ground.
can we set time in the clock? or it should run from 0? could you please answer
We can set the time but since it's not an RTC clock, we have to set the time again when the power goes off
let's do on a PCB 😍😍😍😍😍😍
👍👍👍👍
How to make it output 12:00 then if it reach to 12:59 it will beome 01:00
I think it's not possible without Arduino or any Microcontroller.
pls share the file sir
Led clock circuit diagram ic Number
Normally I have used 555 timer IC for clock frequency generator in this schematic diagram. But if you want to get the exact 1Hz clock frequency you can watch this video of mine. I have given the link below Link - kzhead.info/sun/Y6uqn9Ccop-dhaM/bejne.html
Can you send me this clock CKT Diagram on my email add
Ok Sir ji 😊
Not Rcd the ckt diagram yet
@@sanjaykhatri6093 I will create a new circuit diagram and send it to your email. Please share your email id.
@@sanjaykhatri6093 Circuit Diagram : drive.google.com/file/d/1J0UyUBunlg3PKrXK-PIB0Ocbat2FN5iB/view?usp=sharing
Morning Sir, thank you for the circuit diagram, much appreciated! Could you please suggest possible solution: Minute counter counts to 59 and then 10min.? It actually doesn't begin at 1min.,, but rather at 10min😢 Thank you for your time.