KZhead

Many people don't know the secret to welding aluminum simply and effectively

KULI TEHNIK
2024 ж. 27 Нау.
590 218 Рет қаралды
Жүктеу

Many people don't know the secret to welding aluminum simply and effectively
How to weld aluminum using LPG gas without using flux
Many people still use flux for welding aluminum, for welding aluminum this time I didn't use it

Пікірлер

  • My Dad taught me to weld steel with an oxy-acetylene torch and a small tip and use a wire coat-hanger with the paint sanded off. Then, an old shop teacher of mine, taught me to pre-heat the aluminum before welding it. He said to put a piece of Stainless Steel in behind the hole you were filling up, in your aluminum welding project, and melt the side walls of the casting while you melt in broken strips of CASTING, instead of aluminum rods. The metals HAD TO match, in order to melt together and not break again. The aluminum would run on the Stainless Steel plate, but wouldn't bond to it, so you would have a smooth surface on both sides of the aluminum patch. You didn't have to worry so much about it "falling out the back," since you had a backing plate it wouldn't melt to. Bill, from Tn. 🇺🇸

    @general5104@general510411 күн бұрын

    • Isso sim seria a forma mais correta com certeza! 👍👍🍀🍀🍀🍀

      @sergioalvescordeiro9495@sergioalvescordeiro949510 күн бұрын

    • A 5 inch sanding disc in a drill with 80 grit would take care of your coarse shaping. Then go over it with 180, 220, then 400 or so to finish. Nice job re-shaping the notch!

      @jeremynull6652@jeremynull665210 күн бұрын

    • ​​@@jeremynull6652 Rapaz! Hoje em dia está cada vez mais difícil encontrar profissionais com o entendimento clínico igual ao seu! Parabéns! 🙏🙏👏👏👏👏👏👏👏👏👏👏🍀🍀🍀🍀 Eu também sou um perfeccionista raro e na área que eu trabalho, soluções em fragmentação de rochas, livres de controle, sou o melhor que está tendo 🤣🤣.👍👍👏👏👏👏🍀🍀🍀🍀

      @sergioalvescordeiro9495@sergioalvescordeiro949510 күн бұрын

  • My brother had a case with a bad crack. It was a Yamaha as well and his friend, some kind of exceptional welder, touched it with. A grinder and said that's why nobody wants to mess with it. It's magnesium. I need some special rods so it'll take a couple days because I have to order them. Impossible to tell where it was repaired.

    @keithsuggs7935@keithsuggs79353 күн бұрын

  • And after watching this video with no explanation, the many who didn't know the secret to welding aluminium STILL don't know the secret to welding aluminium.

    @ellesmerewildwood4858@ellesmerewildwood485810 күн бұрын

    • Tout à fait d'accord. Exemple : quel est le type de la baguette utilisée ?

      @pl5484@pl54848 күн бұрын

  • Excellent job, well done, you the man.

    @clintstegall1069@clintstegall1069Күн бұрын

  • الله ينور عليك انا اتعلمت منك حجات كتير جزاك الله خير

    @user-bv9pk7hm7r@user-bv9pk7hm7r29 күн бұрын

  • Поинтересуйтесь, как скоро оно отвалится. Есть более простые и надежные методы пайки, но - с помощью реактивных флюсов и при температуре около 280 градусов. Проверено сотню раз.

    @user-gr4xq8fp5w@user-gr4xq8fp5w11 күн бұрын

  • No tricks involved. It just time, patience and more than an afternoon of experience and trust in ones own abilities. Well done!

    @brucepooley3623@brucepooley362329 күн бұрын

    • 2:10 😅

      @DisanthaNeelakantha@DisanthaNeelakantha12 күн бұрын

    • きく

      @gisunsun@gisunsun11 күн бұрын

  • I watched this comment and showed it to my neighbour. He said that it seemed familiar, so we rented a projector and read it with the entire town and we where astonished, when we found out how original and funny it was, before it actually was copy/pasted from millions and millions before this.

    @timgannon2993@timgannon2993Күн бұрын

  • Индусьі давно паяют алюминий автогеном и не парятся а мьі аргон спец єлектродьі

    @user-ht7ff6yq2h@user-ht7ff6yq2hАй бұрын

  • Was the first aluminium welding I had to learn as an apprentice 25 years ago not as easy as it looks to much heat and poof it just falls away.

    @ScorpioxA1@ScorpioxA110 күн бұрын

  • very Nice work 👍

    @honziiik08@honziiik0824 күн бұрын

  • Nice. This is a metal artist

    @danionescu988@danionescu9889 күн бұрын

  • Well done! Btw is this exciter/sniper 150 v1?

    @foofighter1790@foofighter17902 күн бұрын

  • Paying someone to do this would cost 10 times more than just buying a new case cover.

    @Willy_On_Wheels@Willy_On_Wheels6 күн бұрын

  • Extraordinário 👍👍👍

    @armandolima5742@armandolima574221 күн бұрын

  • Show de bola parabéns

    @paiefilhofulinariabraz4752@paiefilhofulinariabraz47527 күн бұрын

  • Не понемаю что за присадки.здоровья и всех благ

    @user-yb7bd8uc1y@user-yb7bd8uc1y13 күн бұрын

  • Может это эфективно но не просто.

    @iogangrozny9228@iogangrozny92288 күн бұрын

  • ❤ Озвучку добавите ??

    @welznsk@welznskАй бұрын

  • Vraiment une Grande BRAVO

    @user-qz5go8ud9m@user-qz5go8ud9m10 күн бұрын

  • Pengelasan yang jenius luar biasa mantao

    @idekreatifgampang@idekreatifgampang13 күн бұрын

  • Вы используете обычную алюминиевую проволку и разглаживаете потом электродом?

    @nrt8305@nrt8305Ай бұрын

    • Please give a reply .?

      @georgesamkutty686@georgesamkutty68626 күн бұрын

  • Good job

    @TeknisiAsanah@TeknisiAsanah27 күн бұрын

  • I like this trick 🎉

    @MesinSolusi@MesinSolusiАй бұрын

  • لم يستعمل العامل المساعد وهو زيتي

    @cosh7670@cosh767022 күн бұрын

  • Хорошо что у меня есть такой мастер

    @user-wd8yb4nf8c@user-wd8yb4nf8c10 күн бұрын

  • As u get better at welding you will sharpen your tungsten less and less. Your skill will improve that you always keep a perfect gap without touching the material with the electrode. One more critical safety advice for welding in a confined space dont smoke weed before u weld in the confined space.

    @JoeBidenIsGreat@JoeBidenIsGreat11 күн бұрын

  • Это - космос!

    @---fw2ih@---fw2ih18 күн бұрын

    • где

      @user-ir4yf8ci8e@user-ir4yf8ci8e18 күн бұрын

  • Do you explain what welding rod you can aluminum rod?

    @HenryZerrudo@HenryZerrudo10 күн бұрын

  • Bang kenapa setiap aku mencoba pengelasan alumunium selalu melorot ya?

    @kadetsuwoko3918@kadetsuwoko391826 күн бұрын

  • Профессионально! Пропан с кислородом или ацетилен?

    @user-wi1oe4rt8l@user-wi1oe4rt8lАй бұрын

    • Пропана достаточно

      @qwertyqasdfga5188@qwertyqasdfga518813 күн бұрын

  • Era tão mais fácil tampar o buraco com um pedaço do mesmo material e soldar já fiz vários

    @clodoaldojoliveira2831@clodoaldojoliveira28317 күн бұрын

  • if u could only tell us the secret !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

    @S-mz2my@S-mz2my9 күн бұрын

  • Ah ganyan lang pala 👍

    @Cumpang@Cumpang11 күн бұрын

  • Why so many different rods and what are each made out of? Obviously, some are a low melting point alloy that can be melted on top and spread over smoothly. This being a low stress part and not important in terms of safety, I'd trust this repair, but, if available, a factory or used replacement from a wrecked bike would be so much more cost effective in terms of shop time and cost to a customer.

    @oldgeezerproductions@oldgeezerproductions14 күн бұрын

    • I believe it's just various aluminum scrap pieces

      @randyloomis2313@randyloomis231312 күн бұрын

  • When i was 7, i needed this fix on my dirtbike. I tried aluminum foil & duct tape... Failed 😂

    @djnone8137@djnone81374 күн бұрын

  • I thought you had to tig aluminum but time will tell what works.

    @johndoe3johndoe382@johndoe3johndoe3823 күн бұрын

  • Bon travail

    @bacarmohamed7286@bacarmohamed728610 күн бұрын

  • Bro just knitted that thing back together

    @mikhaelcouchman8783@mikhaelcouchman8783Күн бұрын

  • With coat hanger ? What's this guy using to weld with 1711 stick welds

    @johnnysalazar1552@johnnysalazar15523 күн бұрын

  • I can weld enough to safe my self

    @davidsouthwell8196@davidsouthwell81962 күн бұрын

  • Skillful, extraordinary work

    @mdataurrahman1240@mdataurrahman124013 күн бұрын

  • Many people don't need to know.

    @dm55@dm5515 сағат бұрын

  • А можно было положить в пещаную форму разогретую деталь и залить расплавленный алюминий?

    @sergey3791foton@sergey3791foton8 күн бұрын

    • В песчаную неудобно-в глиняную -можно попробывать.

      @user-ev9su3dx8w@user-ev9su3dx8w6 күн бұрын

    • @@user-ev9su3dx8w Я не печник, но думаю что надо не просто глину, иначе её будет пучить, ведь в ней много житкости и будут воздушные раковины.

      @sergey3791foton@sergey3791foton6 күн бұрын

    • @@sergey3791foton я занимался кладкой печей, но по глине вопрос скорее гончару 😁

      @user-ev9su3dx8w@user-ev9su3dx8w6 күн бұрын

  • Rapi telaten

    @Herexracing99@Herexracing9925 күн бұрын

  • Telaten 👍

    @Las_2000@Las_200027 күн бұрын

  • Практически как новенькая, осталось только покрасить 😉👍🏻

    @TEMHblU_PblUAPb@TEMHblU_PblUAPb14 күн бұрын

  • Спасибо, конечно, но мы уж по старинке, аргончиком🙂

    @user-ir4yf8ci8e@user-ir4yf8ci8e18 күн бұрын

    • Ну фик его знает, по старинке ли, у нас так дед варил, когда про аргон ещё в научных фильмах рассказывали😊

      @qwertyqasdfga5188@qwertyqasdfga518813 күн бұрын

  • Viele Menschen könnten auch mit deinem "Geheimnis" etwas anfangen.

    @michaelkuntner@michaelkuntner12 күн бұрын

  • Before welding aluminum, I used to use charcoal on an electric welding machine

    @hailongnguyen7526@hailongnguyen752611 күн бұрын

    • Please elaborate

      @williamlund4184@williamlund41845 күн бұрын

  • А что не показал как шнурки завязывал перед выходом из дома

    @user-ci5yw8bn6d@user-ci5yw8bn6d3 күн бұрын

  • Basta mo lang ininangan wala paliwanag! Kung ano mga klase rod ang mga ginamit mo at materyales

    @norbertinoquiambao4178@norbertinoquiambao41788 күн бұрын

  • Bagus

    @yudopurnomo6525@yudopurnomo652528 күн бұрын

  • ガス溶接がやり易いのか🤔

    @user-uk1ix9zn4v@user-uk1ix9zn4v12 күн бұрын

  • Perfect

    @mohamedashfak4528@mohamedashfak4528Ай бұрын

  • Preciso fazer no câmbio fiat faire kkk salve Alexandre de Moraes kkkkk

    @cesaralmeida9249@cesaralmeida924913 күн бұрын

  • Elpiji mean LPG in Indonesia language.

    @tobiltok2536@tobiltok253617 күн бұрын

  • Sambil Ngomong Dong mas Biar Netizen Faham

    @JakaBaratha-bf2bq@JakaBaratha-bf2bq11 күн бұрын

  • 5:38¿Se puede ser más irresponsable?

    @mrjimy@mrjimy9 күн бұрын

  • Скажи пожалуйста, ты осьминог? 5:36. Ведь точно запасные щупальца есть?

    @user-wy8vp8je8i@user-wy8vp8je8i10 күн бұрын

  • Keren

    @dantermotor@dantermotor23 күн бұрын

  • This guy really needs to stop dropping his bike

    @morbidt9723@morbidt97234 күн бұрын

  • Enakan dalemnya dikasih mal tanah liat dlu om

    @mesincacahkaryacipta8408@mesincacahkaryacipta8408Ай бұрын

  • The welding electrode is made of which metal .? Any code name. ?

    @georgesamkutty686@georgesamkutty68626 күн бұрын

    • Debería ser de aluminio

      @fernandoroblero6499@fernandoroblero649916 күн бұрын

    • competent welder

      @inamuddinilikeyourchannel4220@inamuddinilikeyourchannel422014 күн бұрын

    • There is no electrode. This is gas welding. The filler rods are strips of molten cases of the same material that the case is made of.

      @johncrowley5612@johncrowley56123 күн бұрын

  • THE NGELAZZZ

    @harynugroho8596@harynugroho85969 күн бұрын

  • Yan,ang,hinaha nap,ko,ok

    @user-vz1jd2by6k@user-vz1jd2by6k10 күн бұрын

  • Me gustaría que también dijeran el proceso y los materiales que usan , porque así como pudo decidir si es cierto o nadamas son videos falsos , si no puedo decirles que e gusto solo por ver lo que.hacen con mucha tecnología pueden hacerlo fácil ustedes pero los que los vemos no lo creemos al menos yo ya que e intentado hacerlo y el aluminio al calentarlo así como lo hicieron ,para mi se derritió y no se soldo , no engañen a los usuarios que los ven ,sean realmente sinceros y si no , no le veo el caso de que según enseñen y solo engañen, sean realistas , no culeros

    @user-ep4pw5yo2t@user-ep4pw5yo2t9 күн бұрын

  • Бляяя, я как увидел диск с большими зубами - чуть не какнул!!!

    @user-kb9yw6kk5o@user-kb9yw6kk5o22 күн бұрын

    • А что помешало? 😂

      @user-ov7td9ef3y@user-ov7td9ef3y11 күн бұрын

  • Хоть бы сальника вынял

    @user-yn8ss2wr2s@user-yn8ss2wr2s10 күн бұрын

  • Обычная на пайка алюминия 😂😂😂

    @AlEXsvarshik@AlEXsvarshik10 күн бұрын

  • 😮😮😮

    @tonchanthol5329@tonchanthol532912 күн бұрын

  • Silver rod welding better isnt it ..😂😂

    @2wwwilly@2wwwilly13 күн бұрын

  • Eso sólo lo hace el Mafer

    @user-ny2gp6cl9f@user-ny2gp6cl9f11 күн бұрын

  • うーん、まぁ応急処置というか、DIYとしてならって感じですが… 残念ですが…

    @yk2756@yk275611 күн бұрын

  • 😂 esto no es nada extraño

    @fidecastro8181@fidecastro818118 күн бұрын

  • Это называется не сварка а на пайка алюминия на конструкцию И не надо говорить про сварку

    @user-rh9gt7hd4y@user-rh9gt7hd4y11 күн бұрын

    • This is welding. Clearly the parent metal is fused.

      @johncrowley5612@johncrowley56123 күн бұрын

  • انت تضيع الكثير من الوقت هناك طرق اسرع وافضل من هده

    @user-kg4gy4kv5w@user-kg4gy4kv5w16 күн бұрын

  • JB Weld does the job effectively too, just not as pretty lol

    @seblo8462@seblo84628 күн бұрын

  • And a little piece of aluminum sheet?

    @rosaylafuente@rosaylafuente13 күн бұрын

  • Duct tape.

    @fido139@fido13914 күн бұрын

  • Знаем блять простой способ сварку надо

    @user-ri4ir5dh3i@user-ri4ir5dh3i12 күн бұрын

  • 👍👍👍👍👍👍👍👍👍👍👍👍👍🤏🤏🤏

    @ks-ek4of@ks-ek4of12 күн бұрын

  • Very laborious, that doesn't work. 👎👎.

    @raicing100@raicing10010 күн бұрын

  • Mais barato comprar outra, burrice kkk

    @JoaoPaulo-hu5dy@JoaoPaulo-hu5dy13 күн бұрын

  • Od 8-roku życia spawam czym się da i nie widzę w tym nic niezwykłego o ile to nie magnez.

    @tudor011@tudor011Күн бұрын

  • มันไม่ได้ยากอะไรเลย

    @hackerzbangsaiz9371@hackerzbangsaiz937122 күн бұрын
KZhead