KZhead

How To Weld Aluminum , Hollow Motorcycle Blocks

KULI TEHNIK
2023 ж. 11 Ақп.
946 672 Рет қаралды
Жүктеу

#automotive #welding
How To Weld Aluminum , Motorcycle Blocks With Holes
how to weld a simple perforated aluminum

Пікірлер

  • I learned to gas weld Aluminum from a WW2 book published by ALCOA on welding for Aluminum aircraft parts before the advent of TIG. Takes time to learn and requires some serious practice. My biggest problem was seeing what I was doing due to the bright yellow flame given off making it hard to see when the Aluminum was going to puddle. I did some experimentation and research to see what wavelength that yellow flame was then bought some low density blue industrial filter material (from Lee Filters) that blocks out the color of yellow, leaving you only seeing the Aluminum. Works great!! NEVER let your flame be an Oxydizing flame, always make sure it is a slight carbuerizing flame for best results. Oxygen and Aluminum do go well together as any TIG welder will tell you! Same goes for gas welding Aluminum. !! Well done!

    @johnkemas7344@johnkemas73443 ай бұрын

    • Use a #5 green to block the IR backed up by either cobalt blue or dydimium lenses. They are all readily available. If the filter material works well, that's good but it may not block the IR adequately. You should still back it up with a #5 green lense.

      @michaelallen1432@michaelallen143215 күн бұрын

  • B E A U T I F U L J O B !!! THANK YOU FOR DOING A SUPER JOB AND CAPTURING IT ON THIS VIDEO !!! I appreciate pretty work! ((I just subbed)) My Dad taught me oxy/Actlyn and a coat hanger, welding before I was 10. I got into Iron Art about 11 and was mentored by a local artist for several years, making figurines, etc and selling them at a local art flea market. It is an art to be able to do. I worked as laborer and set-up assistant & later as a journeyman machinist at job shops and then got a break and got on with a major shop. When I first started work at the big shop, a group of craftsmen were trying to weld up a sheet metal fuel tank for a tractor, with 1/16" welding rods and were blowing holes in it and cussing like a sailor. I was 21 and not supposed to know anything. (No one knew I had been raised in a machine shop.) I offered my services. I got a torch with the smallest tip he had and a cutting shield, (I was used to goggles), and a wire coat-hanger and a wire brush and a strip of emory cloth. I swirreled the holes up and dressed them, like they weren't there, with the emory cloth. I asked what they were trying to do in the first place, and it was to weld in a 1/8" female pipe fitting. I got one of those and wire brushed it and installed it. Wire brushed it again and hit it with some Rustoleum Hardhat Spray paint They asked me how I was able to do that. Then I informed them I could do that simple a job by age 10. My Dad raised me in a custom machine shop. The word traveled fast and Before the day was over, the young, know nothing, NEW GUY was accepted in all the craftsmen circles. It's nice to be accepted. I worked there another 37 years..

    @general5104@general5104 Жыл бұрын

    • 👍👍👍👍👍👍👍👍👍👍👍 آفرین ..

      @QTYTQ@QTYTQ Жыл бұрын

  • У тебя золотые руки дружище!!! Дай тебе хороший tig аппарат, ты любого аргонщика за пояс заткнешь!!! Я так пологаю это Индия, там много рукастых ребят которые на коленке что хочешь сделают!!! 👍👍👍

    @user-sh4dm5sg9t@user-sh4dm5sg9t3 ай бұрын

    • ini di Indonesia bukan di India

      @mbara2172@mbara2172Ай бұрын

    • ​@@mbara2172❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤الف تحية لرجال اندونيسيا الابطال

      @user-or2et7ox1v@user-or2et7ox1vАй бұрын

    • да уж, заткнет аргонщика, это ты мощно сказал. Приходили к нам парни на завод с корочками 5-6 разряда, уходили через пару месяцев

      @user-hn4mw8no7f@user-hn4mw8no7f11 күн бұрын

  • I've seen & done all the sorts of repair you could do on this type of casting & I appreciate the skill used relative to the tools involved. It was a job well done. Yes there are other ways of doing it, but this shows that you don't need all the fancy tools. Desire, intent & creativity is of greater importance to achievement. I enjoyed seeing an alternative way to solve the problem.

    @stevetenere4307@stevetenere430710 ай бұрын

  • Кто бы, что не говорил, но руки у вас эолотые! 👍Берегите их.... Думаю, что если бы вы имели возможность получить знания и доступ к инструментам, то сделали бы свою работу лучьше многих оставивших злобные коментарии... 🤔👌👍

    @zub2332@zub2332 Жыл бұрын

    • Mais conhecimento o cara é ferra

      @andreluizdejesuscosta@andreluizdejesuscostaАй бұрын

    • Руки - ноги есть. Голова думать умеет, что мешает заработать денег на инструменты ? Ответ правильный - лень. Если бы не лень, сидел бы не в индии где то в какой то норе, а в уютном гараже в какой нибудь другой более благоприятной точке мира, и делал бы красивые вещи. Но лень вперёд его родилась, по сему он забил на обработку внутреннего отверстия. Да и такие коментаторы как ты, были бы чуточку умнее, дичь бы не писали, а смотрели бы правде в глаза. Поддержатель хренов. Руки у него крюки. А инструмент хороший.

      @nfdteam2nfdteam222@nfdteam2nfdteam2223 күн бұрын

    • @@nfdteam2nfdteam222 если бы каждый баран, который тыкает не знакомым людям был чуточку умнее, то возможно он бы знал, что именно лень является мотивацией прогресса... Чего твк подгорает? Вашу работу и профессионализм никто не замечает?.. Обидно?.. Бывает... 🤔

      @zub2332@zub23323 күн бұрын

  • Had you ever thought of making the hole square, then get a piece of flat aluminum plate, then cut a square to fit the hole from the flat stock, then weld that into place of the hole? Another thing, is you could clamp a piece of steel under the hole, then apply your aluminum filler fight on to the steel, and fill up the hole, after it cools, remove the steel, since aluminum wont stick to steel. 😁👍

    @JK-zl7vv@JK-zl7vv3 ай бұрын

  • well done , personally I would have cut a plate , formed it then welded it in with tig , but when you have plenty of time and oxy acet , thats certainly a way to go.

    @tomthompson7400@tomthompson7400 Жыл бұрын

    • do a video

      @rogerlarson8040@rogerlarson80402 ай бұрын

  • Absolutely fantastic. Gilligan's Island Welding Academy. The best school of all.

    @eddiepiecart6030@eddiepiecart60302 ай бұрын

  • This take more skill than most people will realize. I was not thrilled about the saw blade on the grinder, but the rest was great. One tip, if you spray the aluminum with wd-40 it will keep your discs from clogging, and they cut the aluminum faster.

    @CreativeEngineering_@CreativeEngineering_Күн бұрын

  • Thank you! For me as a welder very interessting. I heard about, but never saw how it works

    @66Gollum@66Gollum Жыл бұрын

  • I would cut and form 2 strips of alum plate and cut the hole square then tig welded it in much less work. but not a bad job for what it was but a long way I miss torch work lol. there's always so many different ways to do the same job keep up the good work & thanks for sharing

    @tryandtakealaska3797@tryandtakealaska3797 Жыл бұрын

    • Do a video

      @rogerlarson8040@rogerlarson80402 ай бұрын

  • Having gas welded Aluminum before I got a tig set up I know how quick and perceptive you have to be to be successful. That said, to do a good job (ie: solid finished part), it would be far better to take a good piece of alu. of the correct thickness, shape it to fit the hole prep the seams and weld it.

    @mikemakuh5319@mikemakuh53199 ай бұрын

  • Для такого нужна снаровка, и чувство металла, попробывал неполучилосб, надо пробывать и пробывать, нетак просто как на видео, парню респект и уважуха!

    @user-ob1bd7cx1n@user-ob1bd7cx1n Жыл бұрын

    • каким газом грел?

      @user-sd4fy5fn5t@user-sd4fy5fn5t Жыл бұрын

    • Practice makes perfect

      @whitefox9@whitefox9 Жыл бұрын

    • Пробовать !!!пробовал!!... Вначале нужно научиться писать без ошибок и русский выучить)))

      @user-nz5gi7pl2z@user-nz5gi7pl2z Жыл бұрын

    • @@user-nz5gi7pl2z А вдруг он не русский? Суть он донес, а до мелочей дое**ться много ума не надо.

      @detidavga5255@detidavga5255 Жыл бұрын

    • @@user-nz5gi7pl2z • “I had to try and try” is the proper grammar for English, the word “tried” would not work in that context for an English sentence.

      @SongWhisperer@SongWhisperer Жыл бұрын

  • Parabéns, um excelente soldador raíz!. 👏👏👏👍

    @vantuirbampi6979@vantuirbampi6979 Жыл бұрын

  • I always preferred torch welding over anything else simply because of the amount of control you have, but welding aluminum looks like a different animal great job.

    @Chris-cz6hn@Chris-cz6hn Жыл бұрын

  • Amazed how well that turned out well done 👍

    @ddoherty5956@ddoherty59567 ай бұрын

  • I've welded oxy and acetylene with carbon steal but not aluminum I've welded aluminum with large spool guns and welding aluminum can be challenging at times but this level of oxy acetylene aluminum repair is quite impressive. I must admit. Well done sir. well done.Wheither you're aware of it or not most welding shops in America wouldn't even tackle that project because most modern day welders don't have those skills anymore to do aluminum oxy acetylene welding repair to that level anymore. so kudos to you sir you put most of us modern day welders to shame.

    @fonhollohan2908@fonhollohan29084 ай бұрын

  • Mis respetos para este señor felicidades exelente trabajo

    @alfredohernandeztrevino4110@alfredohernandeztrevino4110 Жыл бұрын

  • Nie org kata tangan kurniaan Yang Maha Esa... Terbaik bro...

    @ahmadfikri2099@ahmadfikri2099 Жыл бұрын

  • Real life is the best school ever ! thanx man, you share some great knowledge. Most of us should learn those 3rd world's technics for repairing lot's of stuff !

    @dafily1697@dafily1697 Жыл бұрын

    • i do this in a 1st world country but this is just one technique of doing it.

      @biggusdickus9046@biggusdickus904624 күн бұрын

  • Great job. Never saw steel weld rod used to shape and get impurities out. Also great job using circular saw blade on angle grinder. Looks dangerous.

    @Paul-jb7br@Paul-jb7br Жыл бұрын

    • Extremely !!!. Local tool shop refuse to sell me one.

      @pauloconnor7951@pauloconnor7951 Жыл бұрын

    • The welder's last name is "Dangerous"

      @joesjoeses@joesjoeses6 ай бұрын

  • Amazing, now I know how to weld old body parts of my Landrover. Thanks..many professionals prefer soldering, but I will definitely try this way.

    @mateuszszurpit6499@mateuszszurpit64995 ай бұрын

  • с одной стороны - золотые руки! Но с другой стороны, а не проще было латку поставить?

    @Vlad-ob2ts@Vlad-ob2ts Жыл бұрын

    • Легче было житкий алюминий залить . Подготовив участок как при обычном литье.

      @user-gr8yt6iy7k@user-gr8yt6iy7k Жыл бұрын

    • A condition d'avoir de l'aluminium en plaque d'une bonne épaisseur. Avec une telle maîtrise, pourquoi s'embêter...

      @davidfoo2762@davidfoo2762 Жыл бұрын

    • латку надо подгонять по размеру,гнуть, потом всё равно обтачивать, трудозатраты.

      @barmalina@barmalina Жыл бұрын

    • @@barmalina в любом случае, в разу проще, легче, быстрее да и прочнее в итоге.

      @Vlad-ob2ts@Vlad-ob2ts Жыл бұрын

  • muy buena reconstruccion MAESTRO, GRACIAS POR COMPARTIR

    @andresalexanco7703@andresalexanco7703 Жыл бұрын

  • Я конечно не сведую в технологии таких работ, но как по мне все просто замечательно, рукастый человек!

    @user-lv3bo1tc4n@user-lv3bo1tc4n9 ай бұрын

  • Super jest to odrestaurowane i zrobione pozdrawiam twórcę tego filmiku serdecznie 👍👍👍👍

    @andrzejporeda7281@andrzejporeda72819 ай бұрын

  • Satisfying watching that. Repaint it you would never no from the outside it’s been welded. 👍🏻👌🏻

    @michaelashton4846@michaelashton484611 ай бұрын

  • Сейчас так мало кто умеет. Неоправданно долго и сложно. Мастерство нужно, чтоб так наплавлять алюминий. Мне нравится👍

    @ifnic1@ifnic120 күн бұрын

  • Excellent and patient job, with expertise it's another thing

    @gilsonfelix3415@gilsonfelix3415 Жыл бұрын

  • You are seriously talented. Using a steel rod to bevel the edges, making the harness with bits of aluminium rod and using a timber circular saw for the first clean up is just 10/10! You are an ambassador for the forgotten versatility, usefulness and relatively low cost of the now abandoned Oxy Acetylene.

    @redpost2380@redpost23802 ай бұрын

  • Me quito el sombrero ante usted , por su maestría y destreza en su oficio porque se lo difícil que es soldar aluminio y usted domina a la perfección ese arte y porque conserva los 10 dedos de sus manos a pesar de usar la herramienta más peligrosa jamás inventada la amoladora combinada con el disco de sierra 🖐️

    @joseorestesdelgado6574@joseorestesdelgado65747 ай бұрын

  • Great job meister, thank you for sharing

    @GladSadMadWorld@GladSadMadWorld9 ай бұрын

  • Wow!! Impressive results!!! This guy is not only a highly talented technician but an accomplished artist! PS - buy a new part unless your labor is essentially free. The new part would be MUCH cheaper and stronger.

    @mortimerschnerd3846@mortimerschnerd384610 ай бұрын

    • Depende el mercado y su localización, hay países donde adquirir esa pieza nueva es carísimo o no se consigue, es x ello de q las reparan

      @SuperArgentun@SuperArgentun7 ай бұрын

  • Perfectly done job I m from sri lanka 🇱🇰🇱🇰🇱🇰

    @sarathjayakodi2962@sarathjayakodi2962 Жыл бұрын

    • Uvufyfy

      @saber90opp74@saber90opp74 Жыл бұрын

  • Nice ! and a carbide tooth cutting wheel for the rough shaping is actually a clever choice because abrasive disks will get gunked up by aluminium in not time

    @TheOneAndOnlySame@TheOneAndOnlySame Жыл бұрын

    • PAM cooking spray is all I gotta say. Idk what it does but it's cheap and keeps a carbide blade clean like new every pass. I only know this because I work in an aluminum fab shop.

      @codyjohnson5674@codyjohnson5674 Жыл бұрын

    • @@codyjohnson5674 HM. Ok , will try. And you for to try isopropanol alcohol as a cutting fluid for aluminium too, it does wonder

      @TheOneAndOnlySame@TheOneAndOnlySame Жыл бұрын

    • @@TheOneAndOnlySame alcohol is not explosive but its is highly flammable. We have weld slag flying all day non stop. ISO alcohol is not a good idea in our shop.

      @codyjohnson5674@codyjohnson567411 ай бұрын

    • @@codyjohnson5674 Hmm ok. Try it on a lathe then 👍

      @TheOneAndOnlySame@TheOneAndOnlySame11 ай бұрын

    • @@TheOneAndOnlySame a lathe cut dont get anywhere near the temps a weld contains. Never seen a personal lathe make molten metals.

      @codyjohnson5674@codyjohnson567410 ай бұрын

  • perfeito, ótimo soldador.

    @miguelfortesn1491@miguelfortesn1491 Жыл бұрын

  • Love it. In the States you could find someone to do this work but most likely the bike would be scrapped.

    @farmerkevin@farmerkevin8 ай бұрын

  • Excellent. This is a $1000 work if you get it done by a professional company thats why ppl change parts as a whole. Well done !!!

    @SMILYHIPPO@SMILYHIPPO10 ай бұрын

  • He's a "mounster"😂😂😂 Amazing work!!!#

    @rodolfo7624@rodolfo76249 ай бұрын

  • Good job IF no mechanical strength is expected, hopefuly the case here. I suppose in some areas aluminium plates will be more costly and difficult to find than simple soldering rods or alu sticks and work time is almost costless. And great job soldering with acetylene torch, so delicate with aluminium.

    @davidfoo2762@davidfoo2762 Жыл бұрын

    • I would guess that to be oxy propane as it leaves no soot. I would be interested to see a impact test. Sometimes old school works great.

      @vicferrari9380@vicferrari9380 Жыл бұрын

    • These engine covers are made from crappy cast alloy, so the weld is actually stronger. I know because I had my old R6 engine cover repaired this way and it outlasted the bike (engine failure 6 years and 30,000 miles later).

      @kaba_me@kaba_me Жыл бұрын

  • Sangat bermanfaat sekali, jadi tekniknya hampir mirip dgn pengelasan besi yg sudah bekas dilas listrik Saran aja bang, kalo pake mata potong besi di pakein dimmer biar aman Tapi terima kasih sekali untuk ilmunya

    @anjargin4663@anjargin4663 Жыл бұрын

  • Top Work.... 👍🏾💪🏾💪🏾💪🏾💪🏾💪🏾💪🏾💪🏾💪🏾

    @Nobody-vf6xf@Nobody-vf6xf8 ай бұрын

  • Great work! With GTAW process I'd finish that in less than one hour, exactly 55 min.

    @A.Hisham86@A.Hisham867 ай бұрын

  • Looked like a good place to use an old stop sign.

    @wreckum56@wreckum56 Жыл бұрын

  • Good job. The carbide cutting blade is always an extremely dangerous tool. I use one myself & being careful not to use it in positions where it might jam & kick back is of utmost importance!

    @stevetenere4307@stevetenere430710 ай бұрын

    • My father lost a fingertip with one of those

      @ZirconGames@ZirconGames7 ай бұрын

    • Yes, they are like staring down the barrel of a loaded gun. The Danger is high & the outcome can be bone chilling.@@ZirconGames

      @stevetenere4307@stevetenere43076 ай бұрын

  • Cool repair, right up to the saw blade on the angle grinder, terrifying.

    @maaseyracer@maaseyracer Жыл бұрын

  • Great Job!

    @gianlucaspi@gianlucaspi Жыл бұрын

  • Excelente trabajo, felicitaciones 🎉

    @juancarranza5611@juancarranza561111 ай бұрын

  • Lo maximo maestro felicitaciones ,,,gracias x el tutorial desde lima peru

    @juanpabloserranoquispe48@juanpabloserranoquispe484 ай бұрын

  • me encanta,pedazo de video eee,y el interior,como lo pules?,un saludo.

    @ivangimenezmolano8830@ivangimenezmolano8830 Жыл бұрын

  • Super!! Great skill you have, I have a query can we do this using mmaw/gma process? Using same electrode grade 4043 using Flux cored or bare electrode.

    @subratnayak6742@subratnayak674210 ай бұрын

  • 이것도 진득하지 못한 사람은 못할듯 열정도 대단하시네요^^

    @tiger09298@tiger092987 ай бұрын

  • Wah idea cemerlang bang

    @Kita.Ada.C.H.l@Kita.Ada.C.H.l Жыл бұрын

  • I love watching you work. Very skilled I have never seen that technique with the welding rid to remove impurities either. In my ignorance can I ask is this Argon gas.

    @Stevo736@Stevo736 Жыл бұрын

    • Are you talking about the gas emitting the flame? Argon is inert

      @intothevoid3962@intothevoid3962 Жыл бұрын

    • oxigen dan acetilin

      @yudhi0227@yudhi0227 Жыл бұрын

  • Can be done much faster with a MIG welder. I had my R6 engine cover repaired this way a few years back. It was just $40 for a new part, but Yamaha did not have it stock and I could not wait.

    @kaba_me@kaba_me Жыл бұрын

    • Those rods he's using can be used to stick weld aluminum with an electric arc welder too. I've used them to fix motorcycle timing covers.

      @pR1mal.@pR1mal. Жыл бұрын

    • La varilla es de aluminio?

      @salvadorcano5493@salvadorcano5493 Жыл бұрын

  • Great job, no voids in there. But that saw made me nervous.

    @VenturiLife@VenturiLife Жыл бұрын

  • Resolvido o problema, parabéns

    @claudiotadeusilveira@claudiotadeusilveira Жыл бұрын

  • Muy buen trabajo. El hombre la tiene muy clara y conoce de herramientas, estoy seguro que conoce los riesgos de usar la amoladora sin protección. No creo que haga falta explicarle.

    @robertopablovizcarra3023@robertopablovizcarra30236 ай бұрын

  • Excelente!! Q usa como fundente?

    @gabrielrohringer7630@gabrielrohringer7630 Жыл бұрын

  • Tôi cũng là người thợ hàn tôi nhìn tay nghề anh này thì tạm được gần bằng tôi.cố gắng lên nhé.

    @emyeukhoahoc.176@emyeukhoahoc.1767 ай бұрын

  • Great job👍

    @jeremijerem912@jeremijerem912 Жыл бұрын

  • Great job boss🎉

    @Gursewaksingh-vh7vn@Gursewaksingh-vh7vn Жыл бұрын

  • trabalho simplesmente espetacular, mas não era mais fácil soldar uma chapa de alumínio no buraco e depois dá acabamento?

    @IvysSSousa@IvysSSousa8 ай бұрын

  • what addition material do you use?

    @pagecosta@pagecosta Жыл бұрын

  • Que buen trabajo excelente, que varilla usaste?

    @carlosherrera268@carlosherrera268Ай бұрын

  • Good job

    @doolteen4291@doolteen42917 ай бұрын

  • ¿Qué material uso además del electródo? el alambre

    @Najbaalam@Najbaalam7 ай бұрын

  • Wow! Most folks would just consider it scrap aluminum and throw it on the pile.

    @nathanhale7444@nathanhale7444 Жыл бұрын

  • Great job! That carbide saw blade on the angle grinder to rough shape the weld is a bad idea. Using without a guard is a really bad idea. It works but will eventually end in disaster. Do yourself a favour and stop while you are uninjured!

    @TricksterJ97@TricksterJ97 Жыл бұрын

    • I use a carbide blade with aluminum all time but will only use it on a air grinder. The air grinder doesn't have much strength and will stall easily so it has very little kick back to it. I agree using it on a electric grinder is asking for trouble. Interesting to use the 6013 rod to flick away the oxides.

      @vicferrari9380@vicferrari9380 Жыл бұрын

    • 그라인다 카바없이 하는건 위험하지만 대부분 카바 벗겨내고합니다 안좋은 습관이긴한대 카바가 잇으면 그라인더질하기가 힘듭니다 특히.구석같은곳은 카바잇으면 그라인더질이 안댐 그래서 대부분 일할대 카비없이 하는경우가 대부분입니다

      @totoy33@totoy339 ай бұрын

    • Он страха не знает😅 ❤

      @user-yh6dr9jn4x@user-yh6dr9jn4x8 ай бұрын

  • muito bom, excelente profissional

    @andreandrezao6453@andreandrezao64536 ай бұрын

  • Qual o número dessa ponteira que você está usando

    @Geronimo820@Geronimo8207 ай бұрын

  • Profe suelda oxigeno co acetileno o.lo puedo hacer con gas butano gracias saludos desde resistencia chaco argentina

    @carlosjoseaguirre4194@carlosjoseaguirre4194 Жыл бұрын

  • Excelente!

    @pedrorodrigues8853@pedrorodrigues8853 Жыл бұрын

  • Hadir nyimak boss ku suksesselalu buatbossku 👍👍💪💪

    @pintobengkel8112@pintobengkel811211 ай бұрын

  • Я як зварювальник алюмінію на tig141 шо можу сказати. Руки в цього хлопця прямі, але це з'еднання хочь і виглядає гарно проте не буде мати монолітної структури. Алюміній дуже активний метал і потребуе доброго захисту зварної ванни. Також потрібно змінній струм для руйнації оксидної плівки.Маю зауваження до такої великої наплавки. Це створить деформації та напруги у виробі і швидше за все його можливу руйнацію в майбутньому. Не думаю що такий спосіб є нормальним і що він вартій уваги, але автору лайк за винахідливість

    @user-AngryUkrainian@user-AngryUkrainianАй бұрын

    • ты считаешь что тебя кто то понял?

      @netSerf777@netSerf77725 күн бұрын

    • @@netSerf777 для чего ваш коментарий? какая с него польза? разжигание? оскарбление? если не понимаешь есть переводчик

      @Seriyification@Seriyification25 күн бұрын

    • @@Seriyification я просто не понимаю зачем говорить на региональном языке в интернете на иностранном канале, а что я тебя задел? ну тогда открывай ротик , заправлю тебе полный бак))

      @netSerf777@netSerf77725 күн бұрын

    • @@netSerf777 1. Ну да логика железная. Говорить про иностранный канал и самому писать не на английском (оригинальном языке канала хотя он из Индонезии). 2. Украинский это государственный язык Украины и запрещать на этом языке писать можешь у себя на родине, там тебя поддержат. А это американская площадка где можно писать на любом языке 3. Ты меня не задел, просто хотел спросить для чего вообще такое писать когда в видео автор вообще ничего не сказал и не написал, а ты решил к рандомному комментарию на украинском выставить претензию. Ну и я поинтересовался какая у тебя цель? 4. Ну и про ротик, спасибо, пожалуй откажусь я таким не увлекаюсь. Ну а если тебе нравиться такое можешь предложить своей маме или папе может они согласятся.

      @Seriyification@Seriyification24 күн бұрын

    • @@Seriyification я пишу на международном а не на региональном языке, и это не украинский канал , если бы я захотел что то написать автору канала, я скорее использовал бы английский язык, а по поводу того что я тебя задел, вопрос был риторический, и так понятно что задел, так что открывай рот)

      @netSerf777@netSerf77724 күн бұрын

  • Y por dentro?? Girará bien el motor??

    @juangv72284@juangv72284 Жыл бұрын

  • Excelent.profesor.Ecuador.😊

    @fernandorojas9039@fernandorojas9039Ай бұрын

  • hola amigo buen trabajo, una opinión abría sido mas rápido poner un molde en la parte interior saludos desde chile....

    @cristiansalinas4174@cristiansalinas41747 ай бұрын

  • Dom de Deus. Parabéns.

    @jesuscelio1@jesuscelio1 Жыл бұрын

    • Na verdade Deus não tem muito a ver com isso. É habilidade e conhecimento mesmo.

      @eletronicagomes4427@eletronicagomes4427 Жыл бұрын

  • Wow verra good job!

    @sylvaingirard153@sylvaingirard153 Жыл бұрын

  • Zabardast

    @bilalshafiq4589@bilalshafiq458911 ай бұрын

  • Я смотрел его 2 раза, должно быть, это была очень хорошая работа.👍👍

    @peterisaloftpc4093@peterisaloftpc4093Ай бұрын

  • Хотел конечно задать вопрос, -«почему нельзя было заварить аргоном…» Потом под конец увидел что это индусы

    @Daniilwelder@Daniilwelder Жыл бұрын

  • Imagine the tig welds this guy could make! Just a thought.

    @BEARivrman81356@BEARivrman8135610 ай бұрын

  • You are great!!!

    @WaAallE@WaAallE Жыл бұрын

  • paling demen kalao liat karya anaka bangsa gini .

    @bluedragontoybash2463@bluedragontoybash2463 Жыл бұрын

  • You should have sent that to 6061 KZheadr. He would have fabricated it perfectly.

    @FrustratedBaboon@FrustratedBaboon13 күн бұрын

  • Великолепная работа я сам сварщик по этому и говорю МОЛОДЕЦ

    @user-ek3hj7ls9v@user-ek3hj7ls9v10 ай бұрын

    • понятно какой вы сварщик,не для этих работ выбран инструмент,мастерство начинается с правильно подобранных инструментов,а это шляпа полная.

      @vadimg5413@vadimg54139 ай бұрын

  • GJ Отличная работа 😄👍

    @Den-po5py@Den-po5py8 ай бұрын

  • Out of curiosity where can I buy a pair of safety sandals? I love this blokes footwear

    @Takaraz83@Takaraz838 күн бұрын

  • Hello, what kind of solder do you use for soldering aluminum?

    @favoritdmitry6786@favoritdmitry6786 Жыл бұрын

    • Carbide+ oxigen

      @blackrabbit9601@blackrabbit9601 Жыл бұрын

  • Mantap chanelnya go internasional 🙏

    @mbahsemootomotif3136@mbahsemootomotif31369 ай бұрын

  • Болгарка с таким диском это очень опасно! Смотрел и переживал чтобы пальцы не попилил😮

    @nicks.834@nicks.8347 ай бұрын

  • EXCELLENT CRAFTSMAN ! * clap - clap *

    @George_Avgeris@George_Avgeris Жыл бұрын

  • qual é o material de adição voce utiliza?

    @pagecosta@pagecosta Жыл бұрын

  • Good Skills.

    @jamesward5721@jamesward5721 Жыл бұрын

  • joss, kapan ngaliwet mas, hee

    @kenzyromultimedia4905@kenzyromultimedia4905 Жыл бұрын

  • Did you cast the filler rods yourself? Cool repair.

    @TheDistur@TheDistur11 ай бұрын

  • Very nicely done..

    @matthewq4b@matthewq4b25 күн бұрын

  • Красота!

    @user-vc3if3wi4j@user-vc3if3wi4j Жыл бұрын
KZhead