Thanks master.. to share your knowledge..more power master
@user-hd3yr9ym3x10 ай бұрын
Thank you for watching
@CrazyMe3010 ай бұрын
Great job, nice to see the inner sleeve left longer than the gland base, too many folk cut it right back and you end up with single layer of insulation next to the rough gland inner. That would pass a Chemical plant inspection if it was an E1FW gland. If you use adaptors, the inner sleeve should go past them by at least 10mm though. I think 3 and 4 look a bit short on the inner sleeve.
@007floppyboy Жыл бұрын
Thanks brother appreciate your suggestion
@CrazyMe30 Жыл бұрын
Nice
@zubairalam1669 Жыл бұрын
👍👍👍👍
@sitasuthar98272 жыл бұрын
😍😍😍
@user-gu9xu9fm1f2 жыл бұрын
I’d redo the first one get more bend on it
@Zombie_Longwinger2 жыл бұрын
First cable too long tbh. I would advise not cutting the inner insulation off until after it's in the isolator. This avoids possible scratching of the core insulation. If you score around the inner insulation first before inserting then the inner comes off easier . Good effort though my friend . Spent over 35 years doing swa btw lol 😆
@paulharrison6408 Жыл бұрын
Thanks for the advice sir. Stay safe
@CrazyMe30 Жыл бұрын
Good job bosing..Ilan ang FLc mo 35mm ba Yan o 50mm..stay safe God bless
@josecastillo3801 Жыл бұрын
50mm po sir.
@CrazyMe30 Жыл бұрын
i think this site is in emirates hills 🙂🙂
@arghiegonzales8420 Жыл бұрын
What is the procedure for cable termination...this video all about how to gland the cable
@zayn-mallik4168 Жыл бұрын
It depends on what you are going to terminate from LOw voltage to High voltage
@CrazyMe30 Жыл бұрын
Pls use lug
@closeplus12252 жыл бұрын
THIS CABLES I THINK FOR AIR HANDLING UNITE SUPPLY.
@gcbbuildingproject4782 Жыл бұрын
EXACTLY
@CrazyMe30 Жыл бұрын
You should be using CW glands for outside.
@shaynemacdonald30516 ай бұрын
Thanks for watching!
@CrazyMe306 ай бұрын
That is a CW gland.
@mcryptonite69485 ай бұрын
It is a double compression gland, CW is specially use for outdoor applications and where necessary to provide an IP66. Regards & thanks for watching
@CrazyMe305 ай бұрын
That is a BW gland
@shaynemacdonald30515 ай бұрын
Single compression for indoor use
@CrazyMe305 ай бұрын
Looks terrible you had loads of on the cables but you fucked the bends up totally.
@paulpink9518 Жыл бұрын
Thats the customers req😁
@CrazyMe30 Жыл бұрын
Ang hirap gawin hehe
@lilysofficialchannel Жыл бұрын
Kaya po yan basta pag aralan lng maigi. Ingat po
@CrazyMe30 Жыл бұрын
Nakakairita Ang ganyang disconnect switch master Lalo na yong selector type. Mag termination ka ng 10mm wire. Masakit sa kamay.
Thanks master.. to share your knowledge..more power master
Thank you for watching
Great job, nice to see the inner sleeve left longer than the gland base, too many folk cut it right back and you end up with single layer of insulation next to the rough gland inner. That would pass a Chemical plant inspection if it was an E1FW gland. If you use adaptors, the inner sleeve should go past them by at least 10mm though. I think 3 and 4 look a bit short on the inner sleeve.
Thanks brother appreciate your suggestion
Nice
👍👍👍👍
😍😍😍
I’d redo the first one get more bend on it
First cable too long tbh. I would advise not cutting the inner insulation off until after it's in the isolator. This avoids possible scratching of the core insulation. If you score around the inner insulation first before inserting then the inner comes off easier . Good effort though my friend . Spent over 35 years doing swa btw lol 😆
Thanks for the advice sir. Stay safe
Good job bosing..Ilan ang FLc mo 35mm ba Yan o 50mm..stay safe God bless
50mm po sir.
i think this site is in emirates hills 🙂🙂
What is the procedure for cable termination...this video all about how to gland the cable
It depends on what you are going to terminate from LOw voltage to High voltage
Pls use lug
THIS CABLES I THINK FOR AIR HANDLING UNITE SUPPLY.
EXACTLY
You should be using CW glands for outside.
Thanks for watching!
That is a CW gland.
It is a double compression gland, CW is specially use for outdoor applications and where necessary to provide an IP66. Regards & thanks for watching
That is a BW gland
Single compression for indoor use
Looks terrible you had loads of on the cables but you fucked the bends up totally.
Thats the customers req😁
Ang hirap gawin hehe
Kaya po yan basta pag aralan lng maigi. Ingat po
Nakakairita Ang ganyang disconnect switch master Lalo na yong selector type. Mag termination ka ng 10mm wire. Masakit sa kamay.
Yes boss tyaga lng hehe, salamat po
Wrong glands and no IP washers used.
Wrong glanding
Thank you sir. Appreciate your comment. Stay safe
No good....!🤭
Dress properly your cable