Full Restoration Antique KUBOTA Tractor // Fully Restore and Repair Abandoned Old KUBOTA Plow Truck
2024 ж. 15 Қаң.
243 108 Рет қаралды
Full Restoration Antique KUBOTA Tractor // Fully Restore and Repair Abandoned Old KUBOTA Plow Truck
I hope you have fun with the video! If you have any questions on the used tools, materials or the processes, write it in the comment section - i´ll try to answer as soon as possible!
If you want to support my channel hit the like, leave a comment, subscribe and share my work. It helps a lot! :-)
Thanks for watching! Please subscribe to support my channel.
I hope you like it!
If you like it please Subscribe: bit.ly/3EaCNEI
#kubota #kubotatractor #tractor #plowtruck #dtrestoration #restoration
ماشاء الله تبارك الله عمل جميل ❤❤❤❤
Excellent post and I really enjoyed the music.
What an amazing job good on you all great work I love it nice
BISOUS BONJOUR DE LA FRANCE BIENVENUE JADORE CONTINUER MERCI
Hola amigo, cometiste hasta donde yo observé dos graves errores, primero, las valvulas una vez asentadas no se pueden cambiar de lugar por que todas no asientan iguales, segundo , al empaque de la cámara o culata no se le coloca ningún pegamento, así que corrije para la próxima vez esos dos graves errores, saludos y siga adelante con las restauraciones. Un abrazo desde Buenos Aires Argentina.
i felt dezy watching the video please place your camera properly
Grán trabajo !!!
انت رائع جدا ومتقن لعملك
WOW!........Is there nothing this guy can't restore.
❤❤🎉😮🎉😮
Sei.veramente.un.uomo.veramente.meravoglioso.come ..dic
👏👏👏🔥🔥🔥👌👌👌Гарна, імітація на реставрацію!!!
Não é boa prática soldar sem uma máscara. Os olhos agradecem a proteção da mascara.
Perfect 👌
👍👍👍👍👍👍👍👍👍👍👍👍
Бро! Снимай про российскую или советскую технику, будет тебе миллионы просмотров
Restaurado trator 🚜😉
These SE Asians have a very distinct welding technique. It is because the welder controls are just so so. Which means none of them set up the welder to burn the rod consistently with the welder voltage and amperage set correctly. This is just fine for small implements but for piping and porosity it will simply never do. In fact I had to be qualified for nuclear piping and could weld vertically, upside down, and sideways never removing the rod from the work like they do for thin sheet metal. Good job men. Good work.
Study at school, learn from KZhead 😁
Torque of headbolts, SEAsia? As much as you can get. Here in America if the radiator is not reworked the motor will not be warrenteed. Because sure as shootin the engine will overheat. The water that came out of this one was rust filled, ergo, no antifreeze to keep rust from forming. This coates the radiator tubes for cooling. Excellent work men.
Very nice.. I love it.
Someone please tell the old geezer that Kubota isn't blue it's orange
за трубу 👍можно еще метр доварить вправо и над с метр а то штурману дышать не чем )))🙄😁или в воздухан пустить так вообще будет евро 8 😂👍
Super
I'm kind of confused why even in warmer climates you don't use antifreeze. It has higher boiling point and help resist corrosion in the block. But water is free I guess so that's why they do it
Клапана провалятся от такого притирания
Сказочник ремонта, хоть женщин перестали ставить в ролики, кино одним словом.
А что на Японских моторах корзины сцепления Не центруются??? Что бы вал без проблем вошел. ??????😂😂😂
🚜🚜🚜🚜🚜🚜😊😊😀😁🤩💯
👍👍👍👍👍👍👍
I enjoy watching you guys work but putting the same crappy radiator and hoses back on?
The meaning of ANTIQUE is 100 years old... Geeeeeez
☢️☣️ el aceite al suelooooo!!
Разобрать,помыть, и собрать обратно сомнительная реставрация 🤔.
если нет зап частей или не за что купить то и так сойдет)))😁
@@user-ms9zm2yt4i тогда это Т.О. а не реставрация 🤔😁😁😁
👍
Spray everything including the rubber hose😂
ربما يكون حديدا
It would be better if they put the rear tyre on the right way round
Kabil 11:04😯👍
Вы убиваете головку блока цылиндров
People watch your videos only the place where you clean with gasoline or diesel fuel.... You. You can’t even post the other part of the video, they’re not interested in anything else. 😂
Did he centralise the clutch
vraiment c'est. la formation professionnelle
He should paint them close to what the factory colors were. He always chooses colors that look so stupid together.
Yea no doubt, a green engine??
👌
피스톤링 압축링은 교환해주는것이 맞는데 그대로 조립한다는것은 이해가 안되네
If you got the side covers for the engine you should put them on,it would look better with them on & you need to adjust the carburetor down because it's idoling to high & cut that part of the exhaust that's pointing forward off,better yet just take off the top muffler & just add exhaust pipe but not really long like the top is,about half that then you'll have a good tractor
Все собирали двигателя не. ремонтировали помыл бензином собрал и поехал
👋👋👋👋👍👍👍👍💪💪💪💪
What model is this? At first I thought maybe a L2550 but that is a 3 cylinder, this looks like it’s a 2cylinder. Kinda looks like I see 3 injectors so maybe it is a 3cyl which would be weird cause of how the exhaust manifold has only 2 holes like a 2cylinder would. Has me very confused??? Yep it’s a 3cyl.
Он не пашет
What part of this is a full restoration? ? What was wrong in the first place? ? The engine was disassembled and cleaned and painted a strange color, the valves were matched and assembled separately, the transmission was left as is, the front tires were slick, and the rear tires were rotated in opposite directions.
Why would you paint the motor green??
That thing is an absolute abomination 🤮 they literally took a tractor that just needed a good pressure washing and ruined it
What’s he painting that thing with an airbrush or what?? Definitely not an appropriate sprayer.
You work with what you have, not what you don’t
Meus parabéns vocês mecânicos são muito abilidozos
This is not a full restoration.
Full restoration? Good fake. Grind the valves into the seat, and then pull them out, and not know which one belongs where? Nice fairy tale.