How do you diagnose a bad Diesel Injector Pump | Complete Diesel Pump Repairing
2021 ж. 12 Қыр.
1 795 424 Рет қаралды
How do you diagnose a bad Diesel Injector Pump | Complete Diesel Pump Repairing
#dieselpump
#mechanicalskills
How to repair diesel pump,
What happens when a diesel pump fails,
How to Diesel Engine Pump Set And Fire
How does a diesel pump work,
diesel pump adjustment,
restoration diesel pump,
Super, it's the first video I've seen from this country, when the reparing does not take place on the ground. Respect for this!
True,what happens is these youngsters would have come from a technical college where things are done properly rather than old school where no consequences are ingrained but survival at minimum cost
bcos he is not repairing it!
I know, right!
here is a great opportunity for toolmakers to show their equipment, these mechanics are the best in the world
thank you
An actual shop with metal benches, usually its somebody putting something together literally in the dirt. Nicely done👍
And don't forget the buff/ grinder, that's on a stand too !!!
They are expert. The way they do things. No manual to guide them. Pure experience
Monkey see monkey do .it obvious your related
Just imagine how many times they did it wrong to become expert…
I know everything what they are doing here as it was my job in between '88-'99. We used sonic cleaners and sometimes it still wasn't clean enough, hats off to these blokes washing off in a fkn dog dish LOL, love the work ethic of these folk, regards, UK
thank you
I wonder if I could ask your advice? I have a DAF 615 diesel engine in my boat. Diesel is getting into the oil and diluting it plus I have light grey smoke at the exhaust. Is it possible the fuel pump is faulty and what is the actual fault? Thanks in advance. Nigel Hatten
@@romakayak I'm not familiar with that engine but it might be the seal on the front of the pump, it depends on how much diesel is getting in the oil, if there's so much diesel diluting the oil it could be getting past the rings and burning to make the smoke.. it could also possibly be a leaky injector that just dribbles fuel into the cylinder and that's leaking past the rings into the sump.. It's really hard for someone to diagnose the problem without seeing it and with so little information
@@romakayak sounds like the injectors or the cups to me??🤷🏻♂️🤷🏻♂️🤷🏻♂️
@@christiantorres2950 Thanks for your tip. I found the fault myself, it was the copper seal between the bottom of the injector and the cups. I used a fuel dye to find where the leak was. I changed all the seals and replaced the nozzles and now everything is fine.
Lol, this Chipmunk Speedramps killing me!!😂But nice craftsmanship, much respect for this people!👍
l1q0p
I am watching this while drinking my coffee in the morning!
I remember testing CAV pumps at tech college on a rig like this over 50 years ago !
thank you
Wow, thoughts I’d never see a shop that used work benches, and a test machine to boot! amazing work! Great video
Purpose of the table is to collect spilled oil as you can see at 2:00 .
and clean pans for parts.
Jesus loves you
Right man at right place keep up. Very good.
Amazing practical experience . Finally you start working on a table glad to see That is happening .hopefully the entire Maintenance industry will start doing that.
love to see talibans working
@@apesplanet3301 your ignorant
@@apesplanet3301 They are Pakistanis
Bu video serisinde en temiz çalışan, çalışma tezgahı ve mengene kullanan birini ilk defa gördüm . Güzel çalışma kolay gelsin
thank you
That's so cool. First, everything has to be taken apart and cleaned because the Diesel gets gummed up and clogs. Then they put it under pressure to see which one needs to be adjusted. Very interesting machine. I liked it in the Winter cold months I could plug up my block to keep it from getting too cold so the Diesel fuel would fire early in the mornings. 1988 Mercedes 190 D.
10 secs in and I'm impressed . He is actually using a table.
Ma Sha Allah,,nice work brother.i'm watching from bangladesh. If u open the governor in your video i would be peace.
The first rule of fuel injection repairs, CLEAN IT BEFORE DISMANTLING ANYTHING! The second is to convince the client to change the engine oil occasionally, this one looks like it was never changed.
в бедных странах масло не меняют, а доливают до уровня на угар, плюс двойной перегруз и жара +45 убьют любое масло в считанные часы...
That is rural Pakistan not some Kline western nations shop. In Nigeria this will most definitely be the case.
Good to see the use of a proper bench and vice. Usually it all seems to be done on a dusty solid floor!
Good set up .skilled staff .
🇵🇰👍Pakistan style good job
Toolmakers, look at these mechanics.these are true professionals.they don't replace parts they manufacture and repair them. are the best.
Красавчик, это первый чел который так дотошно отмывает, сто процентов будет работать после сборки, сам там всегда делал, чистота залог успеха, поучитесь горе ремонтники как нужно делать считай в полевых условиях, где песок повсюду.
То, что он работает на столе, а не на песчаном полу, как его соплеменники, уже о многом говорит.
@@CEEDLAND он еще небось все в воде, перед сборкой собирает... ну судя по мисочке..
То что он отмыл - слабо влияет на работу агрегата. Внимательно просмотрите на первый пуск после сборки. Там грязь из плунжеров пошла в мензурки! Не думаю что это хороший старт эксплуатации агрегата.
Плунжера их качество первое дело.
Если не заведётся то это значит плохо помыл)))
لکھتے لکھتے قلم ہی ختم ہوجائے گی مگر میرے پیارے رسول اکرم صل اللہ علیہ والہ وسلم کی تعریف کبھی ختم نہیں ہو گی ❣😍
well done, keep up the good work.
Skillful workshop team. Nice job. Esselamu aleikum...
This guy has a bench most of the time they work on the ground big improvement
I was thinking this the whole time.
Those pump parts has to be really clean and kept that way during reassembly.
And his still got a Big hammer, every thing they fix is with a hammer
this is not fair. Table must be taken away.
Agree, first time I have spotted a Pakistani work bench.
بہت خوب صورت جناب مگر آپ نے بیک سیڈ ریس والا ٹاپا سلو فٹنگ میں نی دکھایا ہے
I'm lifting my hat. This is skill. Good work. 👍
Nice use of the torque wrench and the install of new seals and gaskets
PROFESSIONAL👍🙏
The parts tables are now on my wish list
Watching from Kenya, good work
mko kila mahali..😂😂
OMG! I see a nice work bench with tools, and a coffee to boot!
It's tea...they are a nation of tea drinkers...😋😋
just the tools and machines to do the job all the rest is skill no bullshit probably cost effective as well great job just by the way he handles his tools you can tell it aint his first disco
most clean work space ever (in parki)
So strip, clean, re build, re grease, re seal, re oil, re set. Thank you 😎
Good job sir.watching here..
Hey look….. the guy built a workbench and stands up to work…. Wha a concept!
It may look rough compared to our garages but these men could show 99% of western mechanics proper work ethic, And how to recycle things unlike our throw away society, And not one cordless tool insight !! Imagine telling any of our mechanics sockets/spanners only no cordless etc, They would shit a brick and go home crying to mama.
Jim you are so right we seem to have it all ass backward skill is what rules not tools cordless tools don't seem to make the job cheaper
Have either of you ever worked in a diesel injection shop? I have. We rarely used anything other than 1/4” drive and 3/8” drive ratchets and sockets, wrenches, and the occasional soft faced hammer. No impacts in sight because we were dealing with small hardware.
All by hand...true machine....
They use a nice bench, but giving the part a quick rinse before working on it would also be advised. Helps keeping your parts clean throughout the process and is just an overall good step in QC. It doesn't even have to be a lot of work. But just a quick rub down with some soapy water to get most, but preferably all, gunk off before you start disassembling. And of course cleaning parts as you go so you don't contaminate everything you touch with dirt.
Jesus loves you
one of the most beautiful videos
Zabardast yah jo app nay table par kam kiya yah teek hai
Good job man;thanks!
Thank you for showing jayahind.
A PURO ÑEQUE...QUE CAPOS SON..............FELICITACIONES DESDE CHILE....JUNIO 2022......................
Excellent skills and workmanship
thank you
โปรเฟสเซ่อร์ แห่งการซ่อมปั๊มหัวฉีดดีเซล ดูแล้วเพลินไปกับการปฏิบัติงานครับ..
ماشاء الله عمل ممتاز وشغل نضيف الله يفتح عليكم ويرزقم باكستان فيها عقول نضيفه
Son capos estos viejos con poco la hacen todas...👍👍✌🙋
Best work...... Super
Pinnar frictions Halifax 1967 real cutting edge stuff performed on a table WoW
excellent skills
Que grandes mecánicos!!!!
Skillfull and good job,,, mantapp tapi safety kurang
I can't believe it it must be fake, he's not working on the ground in sand and dust ?? That mecanic seems to know is job perfectly well.
If he didn’t have to have a reasonably clean space for injection pumps you best bet he would be in the sand.
I bet they were expert on any model by the way they do their job...
eres un fenomeno.....bravo.
Out standing skills
Excellent.....crude, but excellent👍👍🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸
is good to see how others country do some job i can learn a few tricks
This is a very good machinists
Молодость вспомнил. До армии и чуть чуть после , работал слесарем по ремонту топливной аппаратуры дизельных двигателей. Работа , я вам так скажу очень ядовитая .хотя и оплачивается не плохо. На видео чувак молодец . Качественно к делу подходит.
thank you
Great work
Impressive work
Hola genio saludos desde Argentina . Muy bueno lo que hacés saludos
Boa noite parabéns muito bom
Excellent workmanship. These guys can build better automobiles if they get finance.
Do you offer a training course for servicing and repairs for the diesel pumps if so how long does the training take and how much is your fees in US$?
a metal table? wonder how he got his hands on that luxury.
I liked the dirt ground table better, and when they reuse the old fluids that contain all the good stuff on them that help to break in the new components!
The Boss told them no more working in the ground !!!🤣🤣🤣🤣
Finally someone standing at a bench instead of crouched down in the dirt
Thanks for the video.. Gives you an idea just how much some company overcharge for repairs/overhauling work right there...
thank you
I like 👍 your invention
Những sáng tác của Sỹ Luân nghe mãi ko phai.. Phúc hát rất hay và ấm áp
good job !!! nice video !!!
Dobra robota proszę o więcej podobnych filmów
Mantap p bro
this is not diagnosis, it is repairing already, they are highly skilled craftsman
Salam nice video hy,same isi tarh ka pump hy jis ki side plate nahi hy,us tarh ka pump ka kholna jorny ka video bna lo plz.
Thanks my brothers
golden hands.... so classy
Excelente trabalho, isso que é trabalho bem feito.... very good work.
how
Jesus loves you
Respect.
Good job 👍
Il fond du très bon travail avec les moyens qu'il ont pas de boulonneuse à air comprimé ou boulonneuse à batterie ,bon courage
thank you
Good sharing
Wow! These guys really know what to do 👏
it's not that complex, it's a simple pump
São muito bons mecânicos com os poucos recursos que têm 👍
A NECESSIDADE FAZ O SAPO PULAR
Jesus loves you
Good work
Perfekt 👍👍👍👍
I am also a injection and nozzles expert I base in nigeria with over 20 years of experience
not sure whats more impressive the work or the fact theres no steel to cap boots n they wearing sandals
Very Nice
very good master
Muito legal esses videos os piazada sao bao dimais
I would of washed it down before taking apart!
unappreciated talent.
Overhaul and testrun seems like fine work, thanks for sharing. But I did not get that diagnostic part.
Ттттттттитттттроъъъ89ш88
Testing that the injectors were delivering fuel within spec?
@@DJW1959Aus I associate "diagnosing" with locating errors by looking for symptomes or/and doing tests, Pre teardown. Those final adjustments I would call obligatory calibrations and performance quality insurance. Have I got my understanding of the word wrong ?
@@ogreunderbridge5204 Oh, I see, well, we have not seen the diagnostic part so can't say anything about that.
Good job
Чувствуется творческий подход к работе
thank
Первое видео, где есть верстак.
Прям с языка сняли.
Еще бы здесь в песке кувыркали.
первый раз вижу чтобы они на столе чтото делали
Это вип мастерская .
Да, точно. Они всегда, всё делают на полу,сидя на жопе. А этот на столе. И что, немаловажно на чистом столе.
Не,не будет работать. Песка с дороги не будет в этом насосе... Так нельзя.
First time i see them using a work bench and using clean fluids ! Not reusing the same dirty oil ! I'm impressed , a job well done !
@@user-jz6wr8dx9w согласен.нк притрется
En la prueba de flujo... uno de los inyectores aportaba menos combustible que los otros cinco... ¿Porqué no solucionaron ésa falla...?
Porque no es una falla ya que esta dentro del rango aceptado. Ademas son probetas finas, si fuesen mas anchas apenas se notaria la diferencia.