Stage6 Sport Pro clutch rebuild
2023 ж. 27 Қыр.
94 773 Рет қаралды
Restoration of Stage6 Sport Pro clutch tuning, redesign of spring mounts, making new ones and self-tuning.
There is also a video with restoration of Stage6 Torque Control MKII • • Stage6 Torque Control ... .
Other social media • linktr.ee/samodel
Email • makulaturafis@icloud.com
Тюнінг для скутерів t.me/oholoshennya_moto
Hello Oleg👋 nice to see you this repair and modifikation is absolut genius from me 👍👍👍 i wish you a nice weekend
Awesome video again samodel I learning so much about adjusting scooters with your videos Keep posting
Muito bom. Vc é doutor, sou do Brasil tenho uma jog 50, aprendi muito vendo seus vídeos
Шикарно сделано. Браво
😊Great Solution for this Problem 👍 I got the Stage 6 Racing Clutch with same Problem, i think i try your Methode with mine 😊
Красавчик 👍👍👍
Уж пружины мог бы и в перчатках натягивать. Береги руки пожалуйста, они ж золотые у тебя.
Да руки очень сильно надо беречь, я тоже любил мототехнику покупать и восстанавливать но месяц назад случайно перерезал указательный палец и сухожилия в нем, хирург сшил все но палец на 30% работает и в согнутом положении (не розгибается), и теперь врятли я буду так ловко чинить что либо, очень жалею что взял этот чертов нож в тот день.
@@Lard-st5ji офигеть, очень жаль что так вышло. Сам как то раз порезал большой палец на руке, мне походу повезло что я не перерезал связки, теперь на пальце красуется не маленький шрам.
@@chayniksfunkcieyjopa Да тебе повезло, потому что сухожилия в пальцах сложная штука и они не сростаються без операции еще и потом реабилитация долгая, у меня пока 1 месяц может за пару месяцев восстановлю палец розминками, но это все фигня, самое главное это деньги потому что мне в госс больнице на операцию и всякую мелочь для ухода за пальцем после операции ушло больше 200$(для меня это немаленькая сумма), а в норм клинике бы ушло в разы больше, но были бы деньги на норм хирурга и массажиста то восстановил бы палец 100%. Короче могу посоветовать ничего острого в руки не брать, а если брать то в перчатках или зарабатывать много чтобы лечили професионалы)
Muy buen trabajo, como siempre!
Genius as always 🦾
Como siempre, Samodel es el Mejorrrr!! Saludos 🇦🇷
you did a really good job man! greetings from italy!
Brilliant as always! Please upload more often.
Проверь что в момент срабатывания сцепления ремень стоит на максимальном диаметре на заднем шкиве. Возможно тебе так же нужна более жесткая пружина заднего шкива или более легкие ролики
Super travail 💪
Молодец ❤
Красава👍😎
You are amazing, brother I've learned a lot from you
Muito bom vc e mecanico preparador muito bom!!!!lhe sigo ha mt tempo...eu tmb suo muito corioso na mecânica..mas vc SAMODEL e top!!!abraço s...BRASIL.FORTALEZA CE...
Parabéns ótima aula
Bravo 👏
Оооо о це воно!!!💣👍
really good man :)
hi . youre knowledge and skills are amazing . thank for sharing .👍
Very nice job sir, we’ll done.🎉
Hola tanto tiempo excelente trabajo saludos de mza argentina
Bedankt je bent mijn favoriet
Great job!
kurcze gdubym wcześniej to widział uratowął bym tez swoje :D jesteś mega pomysłowy ;)
Красава 💪🏻😎
انا اكون سعيد عند مشاهدتي لمقاطع الفديو الخاصه بك انا من العراق اتشرف بمعرفتك
Saludos Estimado Samodel tu eres un verdadero artesano ya solo te falta que fabirques en fundicion tu propio diseño de cilimdro refrigerado por agua echo por fundicion de aluminio
🔥
Buen trabajo 🇺🇾👍👍👍
فنان والله
وحش استمر
Sehr interessant und gute Arbeit. Ist abonniert 👍🏻
Mega dobra praca
When you are putting tight springs in again use a old brake cable in a loop and a piece of wood so it will look like a large U shape each end of wire going to the wood or metal with a nut and bolt the same thing that's on a push bike to lock the cable then use every time you need it hope this helps you great videos when you Reply can you do it in English thanks 😊
PS use nut and bolt through the middle of clutch to hold it down put it in your vice so you have 2 Hands 🙌 to help you 😊😮😅😊
Genio !!
Дякую за ідею. Треба взяти на озброєння!
ナイスなクラッチミート👍
👏👏👏👏👏
Użyj imadła następnym razem jak będziesz zakładać sprężynki xd
Ok
Самодел красавчег! Делай видео как будешь делать водянку
Wonderful 🎉
So for city use.. light spring. for having fun... strong spring
❤❤❤
Bester Typ
😍🛠💪👍👍👍💯
Eu tenho uma bicicleta motorizada, mas gosto muito de assistir e aprender com seus vídeos, parabéns 👏🏼. Podia trazer um projeto de bicicleta motorizada pra nós assistirmos.
Since the springs are hooked to the plate, and the plate is hooked to the shaft, you will loose some tension, in result loose some rpms Hence the original setup the spring pulling the pads into each others
Самодел, жду видео с переделкой этой поршневой под водяное охлаждение
Does the Malossi model drill pulley work fine?
👊😎👍
Morning @samodel!!!tell me please what oil do you use to premix and how much %
That's got some pull for a 120cc
Lütfen daha fazla video
La Classe
Siema Samodel dawaj więcej filmów
бімба
Привет 👋, давай видосик на разгон как будет 🚀
💫💫👌🏽👌🏽👌🏽
Кстати я бы еще колодки сцепления после пропила весами проверил
Ps i was watching the one where you made a full Exhaust it was very good would it not be better to get a old one cut up in sections then flatten them out use them for templates rolling them on the bench bar tac them together then fully weld up less dangerous
Le demarrage est bon avec un tour/minute bas ou haut??
Just you need a drive belt more thinner as honda-bando 23100-GG2 for get better results in medium- top speed and get more rpm when started, also change try to changes the big torque spring yellow for a lower rpm spring, a weaker spring as 1000rpm, in medium and high speed with the yellow one scoot runs forced with the clutch, if you try one more weaker scooter will run more free in medium and high speed.
привет, самодел !
🇧🇷
Yaylar gergin mi olmalı?
Течь масла с карбюратора кейхен Хонда такт???
탁월한 선택입니다 4500~5500이 적정한 RPM
Can you not put a 62mm piston in it you might need to get Aliminum welding rods of ebay or amazon then drill retap threads but if you have enough space see what the distances for bigger???? apparently the Aliminum rods work well and there cheap??
Hello I have a question. If I do the same thing on 50cc scooter will have the same torque or less because my scooter has very very little torque.
👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍
Привет, скажи а что с самодельным варматором что ты сам отливал? Как он вообще работает ещё?
How many hp does it make? Btw I love your videos :D
Not petrol?
can you tune a yamaha dt50mx
Преднотяг ставить с низу а не с верху,пружинки
Почему
@@Samodel жоще будет
@@Samodel там оба варианта возможны. Разница в жесткости пружин (можно менять не пружины, а положение). Сами не перескакивают, проверял)))
انا من العراق واريد نفس هذا الكليج الخلفي لدراجة ياماها jok apiro من اين احصل عليه
💎💎💎💎💎💎💎💎💎💎💎💎
Молодец рукастый... Груза наверное щяс по 4.5г? на жосткие такие пружины
На видео 6шт по 9 грамм, но уже поставил по 13 и стало лучше
what is the size of your tires man ?
Hey, have been watching you for a while now and you inspired me to customize my bike 😁. I have a small question for you. If you increase the size of the piston you have to give more air on the air screw on the carburetor? Hope you are ok, keep doing your best 👍🏻
if you increase your piston size you will need to change the jet that is inside the carburetor, he shows it while fixing the carburetor in the video before this one. Also, make sure to stay within safe limits, read up on what size piston your stock engine can handle, or your crankcase might have a big hole in it.
Шеф,що за хвірма штангеля( чи сссилка є)??
a.aliexpress.com/_EHYn8IJ
Mon scooter...embrayage accroche a 6000 tr.min. 😉👌
Капец, за то что на больших оборотах движок с места должен трогаться я ваабще не понял, можете об'яснить пожалуста
You forgot the rubber bushings
Hola Samodel de que país sos, contestame
Helo sir i hew gilera stalker 50cc and i tray tu adjust carburator when i tray to ride at first scooter go an then dead now wont start pleas help
ALmost everyone : Let's trow my old broken parts away and buy a new one. Samodel : What is buy? You are fcking mcgyver man haha
Plesse make more Videos
Первый
🥇
😂😂😂😂😂
Все красиво,только не хватает в сцепе трёх резиночек,демпферов
Они хорошо.но тоже притупять розход колодок.особенно когда будет в пыли
В точку. От того что их нет и пружины тупо пальцами ставятся. Преднатяга нет совсем
У меня есть свой печальный опыт. Когда-то купив скутер и еще не знав всей матчасти мне показалось что эти резинки демпферы задерживают сжатие колодок при сбросе газа.Я их убрал и стало вроде получше но через пару тысяч километров я выбросил колодки,потому как у них сильно разбило отверстия которыми они садятся на пальцы платы сцепления! Вот так вот. Соответственно на сток сцеплении без резинок нельзя! Кстати я тоже обратил внимание что на этом тюнингованном сцеплении нет резинок.
Le falta combustible al carburador, las hondas trabajan con un poco de exceso en el carburador al igual que las Yamaha cuando les ponemos cilindros Racing.
а не простіше купити щеплення в зборі і не витрачати час?
😅Hello Samodel i hope you are safe and well.....we didnt heard anything since 4 Months 😢 are we need to be concearned? Please comment if you able to Give us a life Signal 😅
ชแบคันเล็กๆแต่ขอเสียงนุ่มๆเบาๆไว้ขับไปจ่ายตลาด
Grandes 7 nombre flujo contante google es importante para mí
Hola samodel