How to make a hydraulic pipe bender from an old jack?
2019 ж. 5 Қаз.
804 429 Рет қаралды
Friends, hello everyone! In this video I made a cool pipe bender from an old jack !!!
Main channel - qps.ru/gs5du
Original video[TeraFox] - • ТРУБОГИБ из старого до...
This is the simplest version I've seen so far, good job
Bravo. That was amazing of working with what you got.
A perfect project to make this weekend. I like messing around with my powerarc welder but this project will be super useful.
I say well done sir. Great ingenuity!
A steel plate under the jack would remove stress on jack it’s self. Really nice use of an old jack. Old don’t mean not good.
Nice work, great use of materials on hand
I wonder if your strap that go’s around the pipe, if it held pipe tighter against die. It would bend without marks or flat spot
Nice build excellent bands all around great idea and quality bands going to build one now myself thanks to this man putting it out for us to learn from him!
I lick the music and voice
Very cool video! I have a question. What if instead of squared tubes were used 12 gauge sheets as structure?
Brilliant work
decent lil bender man, kudos for the ingenuity....just curious if you could flip the jack to get a bit more angle?
Jack wont like being upside down. He could increase the distance of from where the jack attaches to the bender but then he would have to raise where it attaches at the top.
Top job my friend, you’ve done well
Really nice work.
great simple idea rolls pipe so it doesn't kink so easily, a little more radius in die would improve bend THANX!
Muchas gracias muy buena , genial , muchas gracias desde argentina Dante herrería
Excellent Job guy!
Muy ingenioso parce. 👏👏👏👏
Nice work!!
Awesome piece of hardware, and much appreciate your sharing, of your tips & tricks, my only wonder is where the jack is mounted to the pipe bending tooling, on the edge of the Stand up plate for the jack, and if it's casted out of different kinds of metal it could crack, shatter the small sharp fragments easier, because the pressure on the downward force isn't centralized, at the top it is, but the bottom is slightly off center. Now if the force nessesary to bend the types of tubing your using is a lot less than what the jack is capable of then No worries. I only ask cause I jacked a girlfriends car up with a similar jack that had Cast wheels on it (which I assumed would have been machined out of Cold Steel) but it seems that all these jacks, lifts etc. are made in a country, I won't mention, either way one wheel Shattered dumped the car on the ground and Thank the Lord I wasn't under the car at the time, I could have Crushed for a second time.(unrelated work neglegentces, no Accident straight up neglegentces) I just mentioned for this reason, I would be heart broken to hear that someone was injuried. Especially the fellow making and Sharing his Craft. What would I be able to watch at 3-4 am, before work. Thanks Y'all. Enjoy a beautiful day. Luv Andrew T
Addressing the jack mount problem, Using a 6 or 8mm steel plate between the jack base and spigot would distribute the load and take the pressure off the single bolt through the jack base. Simple and easy addition
Very ingenious.
one could split the tube on a pre bent pipe 90 to craft the bending shoe from
These apps are awesome.
Great Work! I may make one!!
great work boss...
I wondered if Russian... Saw the 3 stripes and all of my questions confirmed.
Same 🤣 adidas
Excellent vijeo!
Great work
Well done
Have you tried bending 60mm diameter 1.5mm thickness chrome pipe?
You have done a good job.
Awsome stuff my friend
They make manual benders,crankout bends with alot less effort,but a great project
Well done my friend
What radious does the roller piece has?
Радиус Плансона маловат, поэтому не большие волны на внутренней части трубы, а так очень здорово! Like
Vggygyyy76 cu
Great idea 😃
impressive!
Great video for reat ides. Good job.
good job ... be aware of the jack it will break any time cause it does not push vertical ..
So far so good)
nice job with nice musique.
Very nice ! Thanks
Way too much force being exerted on to the outside edge of the jack base.
Addressing the jack mount problem, Using a 6 or 8mm steel plate between the jack base and spigot would distribute the load and take the pressure off the single bolt through the jack base. Simple and easy addition
Awesome. What was the wall thickness of pipes please?
3мм
Здравствуйте скажите пожалуйста мах диаметр трубы?
Pravooooooo good id
wow amezing idea
🔥🔥🔥🔥🔥🔥🔥
A machining job for the die will set you back a couple of hundred euros in most european countries. Plus all the other bits and the hours you put in.. perhaps it's more convenient to buy a JD2 bender or some other semi-decent model
homemade? where did you get the block?
Надо сделать пластину под домкратом , а то чугун хрупкий , может ухо отламать
Top Works!!!!
This is the first video in which a hydraulic system is used instead of electric motor
Excellent
Good job..
Wow good
Wow 👌 excellent
Thanks for sharing 🤨🇸🇳
Good morning my friend. Second like!
vary gooed
Ide bagus bang..😁😁😊😊
👍🇰🇷👍한국에서 응원합니다
Crooked Bottom of Jack could break anytime
More like , including a old jacks in a pipe bender.
Genial
Very ingenious
Size?
Amazing Mr Russian guy.
хороший трубогиб, конструкция понравилаь, только привод лучше делать от подкатного домкрата
Бюджетный вариант
Fill the pipe with sand before you bend it you will get even better bands
I was thinking that heating the pipe with a torch would also make better bends.
تعديل بسيط كانت بتطلع احسن بكتير
Do you sale the die and machine?
No
@@Newterafox you might need to add a plate to bottom of jack too keep it from breaking or bending .. some of them were made of cast metal .. good build ...
How much this sir? I Need this One
A 3 quarter ALUMINUM EMT tubing bender at home Depot cost $52 dlls tax included less cheaper than the 1 this guy made. Also The Home Chepot 1 can do different offset. I will say no gracias comrade! Wait just found 1 at my local swapmeet for $7 bucks!
Throw a piece of 3/4" DOM 1/8" wall in your emt/conduit bender and see what happens when you try to bend it. That's what the bender in this video is built for.
Как тебе элпромовские болгарки?
Отличные!
@@Newterafox просто хотел себе взять! Почём они у вас?
That god damn music
👍👍👍👍👍👍
Quiero comprar una dobladora como esta, pero para tubo de 40 mil diámetro.
Mi dirección es calle Jesús Álvarez 16 Alzira Valencia España. (. GRACIAS.)
Base cylinder it gonna break
Verigood films distance Perú
Nice job, subscribed! If you want more subs, feel free to embed your video on our homemade tools forum; looks like you're one of us :-)
बिल,ज्वर
looks kind of rough in the corners doesn't look smooth the roll cage for a drag car would not pass cuz of them ripples in the tube
겁나 힘들어.. 보이네 ㅎㅎ
Кайф👍
Only watched part it was hard to read and watch at same time. Could not follow so stopped watching
Ocei
А че все на английском то, ты же вроде русский... Отснял бы вариант на русском.
Полная версия с русской озвучкой: www.youtube.com/watch?v=CxL40...
Ссылка не рабочая
You can helb me
Inside radius is kinked, epic fail!
I dislike the music
Any chance anyone here has plans for a similair build ? @familyDIY can you share some ?
Well done