KZhead

How to make Laser Security (Theft) Alarm using SCR - 1 KM Range

Anurag Projects
2023 ж. 15 Нау.
1 272 481 Рет қаралды
Жүктеу

How to make Laser Security (Theft) Alarm using SCR - 1 KM Range
Required Components:-
1) C106MG SCR (silicon-controlled rectifier)
2) 680 ohm Resistor
3) 100uF 25V Capacitor
4) Laser Module
5) LDR Sensor
6) 5V Buzzer
7) Push to OFF switch (Normally Close)
👉Circuit Diagram Link :-
drive.google.com/file/d/111rZ...
➡️ Buy Online Robotics and Electronic Components at Lowest Price in India...
👉Website Link - robocomp.in
#alarm #electronicsproject #sensorproject #theftalarm #circuit #security #securityalarm #anuragprojects
Thank you for Watching......

Пікірлер

  • One kilometer range? Good luck with that. When I was a kid, I built a similar circuit that would switch a relay on when the beam was interrupted, and off again when interrupted a second time. I placed this across my bedroom door so when I entered my bedroom, the lights automatically came on, and when I left, the lights would shut off. It didn't take long for my sisters to realize they could place their hand through the beam then run away leaving me in the dark.

    @paparoysworkshop@paparoysworkshop Жыл бұрын

    • Really good fun. We enjoy.

      @ShivaShankar-rj4rg@ShivaShankar-rj4rg6 ай бұрын

    • You try this and it works?

      @Sgt.Rafael-kl8bu@Sgt.Rafael-kl8bu3 ай бұрын

    • Can you make a video on it or send a circuit diagram

      @milankumar1835@milankumar18359 күн бұрын

  • years ago, I applied this for the security of a large area, I circulated the laser in the desired routes through small mirrors.

    @omerbektas5713@omerbektas5713 Жыл бұрын

  • Пять с половиной минут смотрели как надо паять. Гениально. Наверное целый год думали над этой схемой!

    @user-bv7gd7wk5d@user-bv7gd7wk5d Жыл бұрын

    • Скажите спасибо людям.. Можете лучше - покажите. Дерьмо оставте при себе... Весной пригодится.

      @user-os3nn2tx1z@user-os3nn2tx1z Жыл бұрын

    • ещё больше прикололся , на 1 км дальность мощнейшего лУзера.🤣 отстой лузер.

      @777WALLL@777WALLL Жыл бұрын

    • скорее как не надо паять , так как паять он не умеет от слова совсем , даже учитывая видеомонтаж он не напаял , а насрал.

      @habaru78@habaru78 Жыл бұрын

    • Не нравится, не ешь.

      @user-zj6ye6of4i@user-zj6ye6of4i2 ай бұрын

    • Кому не нравится тому пусть повылазит. Есть что то лучшее? Огласите пжалста.

      @user-zj6ye6of4i@user-zj6ye6of4i2 ай бұрын

  • Highlight of the video @4:20 no annoying music.

    @caramba10@caramba10 Жыл бұрын

    • Fake video?? 😂😂

      @mohammedtoufeequrraheman8994@mohammedtoufeequrraheman89947 ай бұрын

  • These build types (no perfboard, just component to component) always amaze me, and I have respect for the folk that show this. I do notice that their soldering irons are always in bad shape. I mean terrible. But I am impressed with the rest of it. Notice sometimes they cut away and have added solder. Not surprising.

    @shader26@shader265 ай бұрын

    • Unless you just bought the soldering iron five minutes ago

      @user-xm6fe7ko6i@user-xm6fe7ko6i16 күн бұрын

  • То что надо. Спасибо.

    @bekzodbotirov7170@bekzodbotirov7170 Жыл бұрын

  • Muy buen proyecto , éxitos

    @ottofrancomanrique7337@ottofrancomanrique7337 Жыл бұрын

    • excellent, great video !

      @arduinomaquinas@arduinomaquinas9 ай бұрын

  • Ist great! thanks, input voltage? is 5v? and power for the lazer? the bat is 1,5v or 3.7v too

    @orlandoparedes669@orlandoparedes669 Жыл бұрын

  • Классный датчик периметра можно соорудить.

    @wasilyok090662@wasilyok0906625 ай бұрын

  • Ótimo trabalho 👏 sucesso aí irmão 🤜🤛

    @pauloinventostube7533@pauloinventostube7533 Жыл бұрын

    • Thank you so much....

      @anuragprojects@anuragprojects Жыл бұрын

    • ахах . Lapsha for stupid suckers. At 4:47, you can clearly see how the sound worked, before the laser crossed. Ahah. The sound of sound even crookedly made. False deer

      @kinostory@kinostory10 ай бұрын

    • excellent video, awesome !

      @arduinomaquinas@arduinomaquinas9 ай бұрын

  • What's the Buzzer model? Is it active or passive? What's the operating voltage? plz mention.

    @sazadur_rahman@sazadur_rahman9 ай бұрын

  • Mạch này làm báo động rất tuyệt vời rất hay hữu ích

    @Mr.ky89@Mr.ky894 ай бұрын

  • C'est plus que parfait.❤

    @marcbaflast7271@marcbaflast7271 Жыл бұрын

  • How long do you think this LDR will last with the laser beam falling on it's surface constantly???🤔

    @chinmoy1955@chinmoy195511 ай бұрын

  • V/nice, useful project. Thks

    @SajidAli-yt5qx@SajidAli-yt5qx Жыл бұрын

    • You are Welcome.... Thanks for watching our videos!

      @anuragprojects@anuragprojects Жыл бұрын

  • Very good excellent really very useful.

    @francomongillo@francomongilloАй бұрын

    • Thank you so much…..

      @anuragprojects@anuragprojectsАй бұрын

  • Sir you are a expert in this field I have a question for you

    @Dannydawson537@Dannydawson537 Жыл бұрын

    • Yes, please ask.

      @anuragprojects@anuragprojects Жыл бұрын

    • @@anuragprojects firstly what a fantastic vid well done sir 👍🏻 I’m currently working on a drone project are you familiar with radio signals?

      @Dannydawson537@Dannydawson537 Жыл бұрын

    • Thank you so much for you like my videos. Sorry, I don't know about radio signals.

      @anuragprojects@anuragprojects Жыл бұрын

  • До 5метров и это хорошо. Свыше как я понимаю нужна оптика, центровка. Благодарю!

    @user-zj6ye6of4i@user-zj6ye6of4i2 ай бұрын

  • Cool - nur das einzige Problem aktuell ist, das es kaum noch Läden für diese Bauteile gibt..

    @DerHamborger@DerHamborger Жыл бұрын

  • То что нужно! 👍

    @bobboboff5326@bobboboff532610 ай бұрын

    • Thanks 😊

      @anuragprojects@anuragprojects10 ай бұрын

  • Height of the object matters a lot here. If someone jumps over or under the laser line, it may not detect. Multiple laser beams at various levels would possibly help.

    @prasadksr6459@prasadksr645911 ай бұрын

    • Mirrors

      @ernestbailey6617@ernestbailey66178 ай бұрын

    • Ufff... 🙄🤷‍♂️

      @bislong365@bislong3656 ай бұрын

    • Usar Laser y sensor IR... Use Laser and IR sensor...

      @frank0-1@frank0-16 ай бұрын

  • Ingenierio disculpe,me podría indicar los colores de las bandas de la resistencia y de cuántos watts ? con cuántos voltios se alimenta el circuito ? de cuántos voltios es la batería para el láser ?

    @pantera1664@pantera1664Ай бұрын

  • Problem :The reset button is not working, when the light is blocked the buzzer beeps and when the object passes away it resets on its own without the use of the reset button

    @rakshith9584@rakshith9584 Жыл бұрын

  • Excelente trabajo.

    @ivan1290@ivan1290 Жыл бұрын

    • Thank you....

      @anuragprojects@anuragprojects Жыл бұрын

  • Is it the same laser module as the one found in dvd head and can we use it in this project? And let me know how much volts should I supply the laser module.

    @user-wi8op3bf6l@user-wi8op3bf6l8 ай бұрын

    • Google

      @kennmossman8701@kennmossman87017 ай бұрын

  • Belo vídeo 👍 Obrigado.

    @raimundononatotim7454@raimundononatotim7454 Жыл бұрын

    • Thanks and welcome 😊

      @anuragprojects@anuragprojects Жыл бұрын

  • You might could use a phototransistor to replace both the LDR and the SCR.

    @t1d100@t1d100 Жыл бұрын

    • a photo diode and a photo transistor will work

      @reyznbran9586@reyznbran958611 ай бұрын

    • @@reyznbran9586 they dont latch like thyristors

      @lezbriddon@lezbriddon10 ай бұрын

  • Instead of a on/off switch button, is it possible to put a timer (like 30 seconds) ?

    @LEdiablo28@LEdiablo28 Жыл бұрын

    • I'm big of LOL

      @sennopo289@sennopo289 Жыл бұрын

    • Yes

      @akinoye@akinoye Жыл бұрын

    • use a capacitor in series with the buzzer. 100 k resistor parallel to the capacitor. then after 1 minute sound will die. again after little time it is ready to detect. change the values until you are happy.

      @sube789@sube7895 ай бұрын

  • preferably join a bistable flip-flop/multivibrator. so that the sound continues when the light is once blocked

    @armantape@armantape9 ай бұрын

  • Excelente vídeo, gracias por la información, cómo le podemos dar uso práctico en el hogar a este circuito?

    @henrysuarez9857@henrysuarez9857 Жыл бұрын

    • Thank you so much....and Welcome....

      @anuragprojects@anuragprojects Жыл бұрын

    • Olá. Vou colocar esse projeto numa plaquinha e instalar uns 4 alarmes desse com bateria de moto na casa toda. Mesmo se os bandidos cortarem a energia, a bateria vai segurar. Mas vou usar 12 volts nesse circuito por isso vou analisar os componentes com mais resistência. 👍🇧🇷

      @user-vs7lv5ij1x@user-vs7lv5ij1x Жыл бұрын

  • No flux? No rosin-core solder? ALL cold joints. What a Rube!

    @covfefewithdave2571@covfefewithdave2571 Жыл бұрын

    • It wouldn’t solder without flux. Of course he’s using flux.

      @Sctronic209@Sctronic209 Жыл бұрын

  • on the left side of the circuit (input side) , what have you used as input? does 9 V battery works?

    @ruddy3962@ruddy3962 Жыл бұрын

    • If you are using 5 volt Buzzer then you should use 5 volt power supply.

      @anuragprojects@anuragprojects Жыл бұрын

    • If you want to use 9 volt battery then you have to used 12v Buzzer.

      @anuragprojects@anuragprojects Жыл бұрын

    • @@anuragprojects okay thank you

      @ruddy3962@ruddy3962 Жыл бұрын

    • What you mean 1 KM Range ?

      @robertpasangha3805@robertpasangha3805 Жыл бұрын

    • Most welcome... Ruddy

      @anuragprojects@anuragprojects Жыл бұрын

  • THe silicon contro rectifier, what is the A and V ? 2/ The resister watt1/4 or 1/2 3/ the ldr sense K?

    @frederickpretorius7093@frederickpretorius7093 Жыл бұрын

    • thanks for reply on my question

      @frederickpretorius7093@frederickpretorius70935 ай бұрын

  • you have to use 2 of them with an AND gate. Other vise insects will ring the alarm. But using a PIR is easier.

    @sube789@sube7895 ай бұрын

    • I was thinking the same but I think we can use a PIR sensor to trigger the secondary laser circuit and then maybe setup some fuzzy logic to monitor the dwell of the PIR and laser to accurately eliminate false alarms.

      @MrXyzasdf@MrXyzasdf5 ай бұрын

  • This scheme is worth a Nobel Prize, or maybe even two...🙄

    @user-go1cz8np3m@user-go1cz8np3m9 күн бұрын

  • Great job

    @electronicskamalhindi7919@electronicskamalhindi79193 ай бұрын

  • Wow thats a nice idea.. but considering the insect and bugs that interupt the laser.. you will never have a night sleep. And in 1km distance the pointer of your laser will be the size of umbrella.😂 garage park assist is better than security bro.

    @mustafadelmonte9413@mustafadelmonte941311 ай бұрын

    • Thanks for the tips! Bro

      @anuragprojects@anuragprojects11 ай бұрын

  • Can we use tip122 instead of ur ic?

    @HenilKayastha@HenilKayastha3 ай бұрын

  • Ngạc nhiên quá, bấm đăng ký kênh luôn.

    @sangtaobuzz@sangtaobuzz2 ай бұрын

  • Great great! Thank you a lot.

    @ZehMariap@ZehMariap3 ай бұрын

    • You are welcome!

      @anuragprojects@anuragprojects3 ай бұрын

  • Mạch báo động của bạn rất tốt

    @thao976vlog6@thao976vlog69 ай бұрын

  • Nice info🙏 5:31

    @orangkreatif-tv7rg@orangkreatif-tv7rg11 ай бұрын

    • Thanks

      @anuragprojects@anuragprojects11 ай бұрын

  • Amigo sirve para sirena de 12v ?

    @leonardoruiz7522@leonardoruiz752211 ай бұрын

  • Ya ,bisa 1 km , jika dapat fokuskan laser pada target.,tapi pada malam hari/gelap jalur sinar laser terlihat merah .

    @ukmkotabandung3609@ukmkotabandung3609Ай бұрын

  • Nice video Thanks for sharing P.S. Adding some details -about the circuit- for the beginners will be great 👍❤

    @khalidmurii@khalidmurii11 ай бұрын

    • Most welcome and Thanks for Watching my videos 😊

      @anuragprojects@anuragprojects11 ай бұрын

    • ахах . Lapsha for stupid suckers. At 4:47, you can clearly see how the sound worked, before the laser crossed. Ahah. The sound of sound even crookedly made. False deer

      @kinostory@kinostory10 ай бұрын

    • nice video

      @arduinomaquinas@arduinomaquinas9 ай бұрын

    • more of a toy than a serious project - very limited demo with no measurements whatsoever - no specs for the laser module - no suggestions on alignment - - construction is really terrible - - the SCR used is way overkill - LDR by itself is a poor choice as it is affected by ambient light-

      @kennmossman8701@kennmossman87017 ай бұрын

    • ​@@kennmossman8701bruhhh... seriously? 🤷‍♂️

      @bislong365@bislong3656 ай бұрын

  • Verry nice

    @blackboysinger3798@blackboysinger37984 ай бұрын

  • Bro is there any alternative transistor there to replace this C106MG SCR. If yes please share the transistor number and it's connection. Please bro need this.

    @kararitchie@kararitchie10 ай бұрын

    • bt151

      @fredmasaiti4507@fredmasaiti45078 ай бұрын

  • I'm kindly asking for a drawing of the circuit

    @mwetenabulwe4954@mwetenabulwe4954 Жыл бұрын

  • Thanks the tutorial usefull and easy to follow

    @gaweown@gaweown Жыл бұрын

  • hola, buenas tardes, noches, días. que voltaje utiliza el circuito???. P.S. - En el vídeo debería decir el voltaje de entrada, nada más te faltó eso. gracias.

    @isaiperez9525@isaiperez952511 ай бұрын

    • Concordo. Isso q eu ia perguntar.

      @altinofreire5826@altinofreire582610 ай бұрын

  • Bhi dusra trangistor use kar sakte ha kiy

    @bbaart1974@bbaart197410 ай бұрын

  • Is there something else I could use instead a C106MG Scr

    @Thegameingdragon-cy5tm@Thegameingdragon-cy5tm2 ай бұрын

  • 1 km lazer will probably burn out the thief, you don't need the alarm actually 😂

    @beterbey@beterbey Жыл бұрын

    • Right Bro...😊

      @anuragprojects@anuragprojects Жыл бұрын

    • 😂

      @konglakhena9100@konglakhena9100 Жыл бұрын

    • 😂 Exactly

      @amitavaroy4287@amitavaroy4287 Жыл бұрын

    • 😂

      @ahmedghareb186@ahmedghareb1867 ай бұрын

  • Is it possible to make a laser security buzzer? For example, if someone enters the room it makes a buzz, just enough sound to alert you.

    @GameOn-li6qe@GameOn-li6qe Жыл бұрын

    • Цей зумер треба під,єднати до ПНЧ до входу і буде вам проблема на вуха!😂😂😂 Обов,ЯЗКОВО скористаюся цим апаратом, тепер злодіїв я напугаю тільки.

      @valeriyvaleriy1671@valeriyvaleriy1671 Жыл бұрын

    • Urm, which video did you watch ?

      @MW-us3sv@MW-us3sv Жыл бұрын

    • @@MW-us3sv same video, where you replied to my comment “(How to make laser security (Theft£ Alarm using SCR - 1KM Range)”

      @GameOn-li6qe@GameOn-li6qe Жыл бұрын

    • Long story short, you are describing exactly the same device as presented in the video.

      @vyacheslavorlovsky506@vyacheslavorlovsky50610 ай бұрын

    • No it's not, it is because once the laser beam is interrupted, it constantly start buzzing till you press the reset button. And this is not how wanted. I want something like, it should make a buzz for second or two and then stop automatically...

      @GameOn-li6qe@GameOn-li6qe10 ай бұрын

  • traffipax detector will be? thx

    @Towards32@Towards326 ай бұрын

  • just light the light sensor when passing by then you will be saved.

    @detsky8384@detsky838410 ай бұрын

  • Which laser module is compatible with the circuit ?

    @tdceylon@tdceylon3 ай бұрын

  • Recomiendas algún proveedor de los componentes electrónicos?

    @henrysuarez9857@henrysuarez9857 Жыл бұрын

    • I buy Electronic Components from RoboComp.in.... You can buy Components from RoboComp.in

      @anuragprojects@anuragprojects Жыл бұрын

  • Hello if I don't put the buzzer can I use the 5 volt out to send this command to activate a contactor to activate a external siren?

    @NIKOSAUDIO1409888888@NIKOSAUDIO1409888888Ай бұрын

    • You can use these two points to actuate anything but through a relay contact.These two points will energize a relay, the relay contacts can further run/actuate anything.Thanks from Pakistan.

      @AzmatAli-ht1rz@AzmatAli-ht1rzАй бұрын

  • What did you do that 2 wires

    @k.chaithanreddykandala6872@k.chaithanreddykandala68725 ай бұрын

  • Тут важна скорость срабатывания на быстродвижущийся объект. Сомневаюсь что схема сработает на быстропромелькнувший предмет

    @aleksandrmarminiv@aleksandrmarminiv11 ай бұрын

    • Эта скорость похоже зависит от ёмкости электролита

      @Mnogolikov@Mnogolikov8 ай бұрын

  • can you made to automatically reset

    @milankumar1835@milankumar18359 күн бұрын

  • con SCR106M em có thể thay thế bằng con nào khác được ạ anh.

    @LyNguyenTiVi@LyNguyenTiVi3 ай бұрын

  • Battery kitne volt ka h ?

    @YashodaDevi-gu8nn@YashodaDevi-gu8nnКүн бұрын

  • What voltage was the power source?

    @richardbennett8268@richardbennett8268 Жыл бұрын

    • Good question, amongst many other ananswered questions !!!

      @paulanthonybridge5741@paulanthonybridge5741 Жыл бұрын

    • USB or 5V

      @kartrok3072@kartrok3072 Жыл бұрын

  • Nota 10 👍🏻

    @joabepereira6381@joabepereira6381 Жыл бұрын

  • VOLTAGE KITNA DENA HOGA AC YA DC

    @studybyshivam2399@studybyshivam23997 ай бұрын

  • How much input voltage?.

    @bhasakararaodayam5094@bhasakararaodayam509412 күн бұрын

  • Nice

    @MuhammadAhmad-vy6un@MuhammadAhmad-vy6un Жыл бұрын

  • What is the voltage of laser module.. is it 3v or 5v😊

    @danica2111@danica2111 Жыл бұрын

    • You can give Voltage 3v to 5v. Thanks for Watching my videos 😊

      @anuragprojects@anuragprojects Жыл бұрын

  • Gostei muito legal

    @volneireichertmutolimda2168@volneireichertmutolimda2168 Жыл бұрын

    • Thank you so much.....

      @anuragprojects@anuragprojects Жыл бұрын

    • Fís como alarme em redor da casa com epello ficou muito bom e botei ligado no amplificador de áudio

      @volneireichertmutolimda2168@volneireichertmutolimda2168 Жыл бұрын

  • This does NOT have 1000 meters range. This is useful over 1 to 5 meters, that's all. CLICKBAIT.

    @user-cd1hs2vw2x@user-cd1hs2vw2x Жыл бұрын

    • You have to focus your laser.

      @shanglang133@shanglang133 Жыл бұрын

    • However, It's just a demo version which may cover 1 square feet that doesn't matter though at all. Anyway, it's good though for security purposes with home made laser light services. Without doubt, it's definitely Praise worthy Good Job 👍. Of course, this person at least deserves appreciation for his invention by making this type of home made security gadget. Love from Bangladesh. Cheers!

      @billetdouxbd84@billetdouxbd8411 ай бұрын

    • @@ucvinhnguyen8745 y

      @brhanedish153@brhanedish15310 ай бұрын

    • Buddy, plz dont write comments like this before using your brain! You're just embarrassing yourself...what it meant is, the distance is dependent on the laser that will be used. There are many lasers out there tht can shine straight beams for long distance.

      @aaronsingh6496@aaronsingh649610 ай бұрын

    • If you want to extend its distance then you can use optical fiber cables as per your need…

      @TechSupportNepal@TechSupportNepal8 ай бұрын

  • 1km? It depends the power of laser or external light

    @tiago6939@tiago693918 күн бұрын

  • 😀😀

    Жыл бұрын

  • Hello sir i want one help for this video detail

    @venkatvn2456@venkatvn24567 ай бұрын

  • It can have 1000m range of the light is that strong 😊

    @indianwoodworks7462@indianwoodworks7462Ай бұрын

  • itu dayanya berapa volt y kak?

    @IndahLestari-yq2ev@IndahLestari-yq2ev2 ай бұрын

  • Hahaha! I am an hobby electronic person. Now I am 70+ and recently found that my hands shake while doing soldering. However after watching this video, which I suppose must be created by an young person, I feel I am not that bad. Thanks.

    @tmsunderrajan@tmsunderrajan Жыл бұрын

    • Your range is 1 km, I made range 10 km. Same components.

      @mohdnaur2418@mohdnaur241811 ай бұрын

    • Wow, this author (of video, sure), speaks and understandss da perfekt inglees. ;))). However, seriously, shaking while soldering, is not only you... So, you are not alone... me too...

      @valshaev1145@valshaev114511 ай бұрын

    • Hint: try to support your hand on something while soldering!.

      @arnbon6241@arnbon624110 ай бұрын

    • @@arnbon6241 Thanks for your suggestion.

      @tmsunderrajan@tmsunderrajan10 ай бұрын

    • @@tmsunderrajan You're welcome. 😁

      @arnbon6241@arnbon624110 ай бұрын

  • like. solo centraljava indonesia

    @sapardieko7750@sapardieko7750 Жыл бұрын

  • Do you have any street camera detector and speed camera detector circuit diagram

    @user-wi2xb9dv9m@user-wi2xb9dv9m10 ай бұрын

    • google

      @kennmossman8701@kennmossman87017 ай бұрын

  • Total expenses??

    @accindividual803@accindividual803Ай бұрын

  • Напругу треба зробити від блока зап. від батарейки не вигідно, краще на акумуляторі ,як лазер так і апарат приймача.

    @valeriyvaleriy1671@valeriyvaleriy1671 Жыл бұрын

  • What is the maximum distance between the LDR sencer and Laser module ?

    @tdceylon@tdceylon Жыл бұрын

    • Depends on which laser light you are using and How far can the laser beam travel? Thanks for Watching my videos 😊

      @anuragprojects@anuragprojects Жыл бұрын

    • 1 to 5 meters.

      @user-cd1hs2vw2x@user-cd1hs2vw2x Жыл бұрын

    • I have a 5 watt laser with adjustable focus that probably would work at one (or two) km. Problem is, it tends to set things on fire... 😁

      @myrlyn1250@myrlyn125010 ай бұрын

  • Tegangan berapa Volt ??

    @amazing__1756@amazing__175610 ай бұрын

  • Day time how can work..

    @thevabhas7225@thevabhas722511 ай бұрын

  • How would you make this so that the alarm times out after 3 seconds and resets the alarm on its own?

    @shanglang133@shanglang133 Жыл бұрын

    • 4 of these would secure a perimeter and tell which fence has been crossed based on which direction you hear it coming from. Perfect.

      @shanglang133@shanglang133 Жыл бұрын

  • Can we use c540mgscr instead of c106mg scr?

    @sumithchiluka9064@sumithchiluka90646 ай бұрын

    • No

      @anuragprojects@anuragprojects6 ай бұрын

  • Thank You 👍👍👍

    @hermanfrans9169@hermanfrans916924 күн бұрын

    • Welcome 👍

      @anuragprojects@anuragprojects23 күн бұрын

  • Jarak nya brp mter

    @udiservis580@udiservis58018 күн бұрын

  • Sir 3 km range wala FM transmitter making project chahie,,, plz 🙏🙏🙏🙏

    @sanjoychakraborty2305@sanjoychakraborty2305 Жыл бұрын

    • Ok, I will try.... Thanks for Watching my videos 😊

      @anuragprojects@anuragprojects Жыл бұрын

  • How many volt we use as input voltage for scheme?

    @dedensukarna8936@dedensukarna8936 Жыл бұрын

    • 3.7 id say

      @anthonyrichard7319@anthonyrichard7319 Жыл бұрын

    • 5v for receiver circuit and 3.7v for Laser Light. Thanks for Watching my videos 😊

      @anuragprojects@anuragprojects Жыл бұрын

  • Please tell me name of this beat in your next video

    @user-wo7em8tb5w@user-wo7em8tb5w2 ай бұрын

  • How to range in circuit and senser

    @user-or1vm5pe3k@user-or1vm5pe3k5 ай бұрын

  • Can i use 100uf 16 v capacitor instead of 100uf 10 v

    @9krishbhoir734@9krishbhoir7349 ай бұрын

    • Yes, you can use. Thanks for watching 😊

      @anuragprojects@anuragprojects9 ай бұрын

  • ESCARGENCY RESEARCH TEMPUS OMNIUS REVELATHE

    @thomaskallmyr@thomaskallmyr Жыл бұрын

  • why the capacitor?

    @kramotakra@kramotakra18 күн бұрын

  • What is the operating voltage of the ckt and laser module

    @jyotiranjanmohanty7276@jyotiranjanmohanty72765 ай бұрын

    • Hi, Circuit 5V and Laser module 3.7V. Thanks for watching

      @anuragprojects@anuragprojects5 ай бұрын

  • Так он через километр будет рассеянный до толщины пальца, там как минимум нужна собирательная линза

    @MrSergias@MrSergias Жыл бұрын

    • А зачем тебе луч с иголку ? Или ты бацилы будешь контролировать ?

      @wasilyok090662@wasilyok0906625 ай бұрын

  • Thanks!

    @herculestubalado906@herculestubalado90628 күн бұрын

    • Most welcome and Thanks for your support 😊

      @anuragprojects@anuragprojects27 күн бұрын

  • nice👍

    @fortunetv1987@fortunetv19876 ай бұрын

    • Thanks

      @anuragprojects@anuragprojects6 ай бұрын
KZhead