KZhead
Тәжірибелік нұсқаулар және стиль

Restoration of a 50 year old Huge Rusty Drill Press. Awesome result!

Restoration In The Back Room
2023 ж. 13 Қаң.
666 175 Рет қаралды
Жүктеу

I got this drilling machine for the price of scrap metal. The headstock raise/release mechanism did not work, the headstock lock lever was jammed, the drill chuck was rusty and jammed, the on/off button was missing, all the electrics were rewound with duct tape. BUT the motor worked!
Restoration process.
First of all, I completely disassembled the drilling machine into parts. Some control levers were broken and new ones had to be made on a lathe.
I cleaned the parts of the hull using a paint remover and a rust converter.
I really like to use hammer effect paint on the body parts. Since the case is made of cast iron, it has an uneven surface and it is the hammer effect paint that hides all these irregularities, while the spray paint would only emphasize all the flaws.
During the repair was completely moved the engine. Rust was even on the rotor! Replaced all bearings and painted body.
The bearings on the spindle were also replaced!
In general, the work was not difficult but took a lot of time, and I will be grateful for the "thumbs up" pressed so more people will see the video and I will compensate for the cost of repairing this drilling machine! THANK YOU
I enjoyed working on this project, and upon completion, I had another "helper" in my workshop, who will often appear in the following videos.
So click "subscribe" and be sure to "bell" otherwise KZhead will not notify you about the release of a new video.
Good luck everyone and take care of yourself!
Sincerely, Max!
#awesomerestoration
#drillpress
#restoration

Пікірлер

  • Thanks!

    @davidm2690@davidm2690 Жыл бұрын

    • David, thank you very much for your support! I just recently connected this function (Thanks ❤️💲), and you are the first one who supported my channel financially !!!! I'm happy 🥲!!!

      @ITBR_Restoration@ITBR_Restoration Жыл бұрын

    • @@ITBR_Restoration Mjhgg

      @nicolaestoica6968@nicolaestoica6968 Жыл бұрын

    • ​@Restoration In The Back Room

      @alexshapiro2582@alexshapiro258211 ай бұрын

  • This press has worked like a charm for my projects kzhead.infoUgkxajoEbapTfqWaadnqb04h6U576yxXp-FE . I didn't even secure it to my table top, mainly due to the fact that I was using a 15 lbs drill vise. It's not flimsy at all as to what others have claimed it to be. Make sure the locking nuts and levers are secured and there won't be any issues with light pressure and patience. I was able to drill through aluminum, plastic, and steel (steel took a while) with no problems at all. Yeah it took a little longer than a regular drill press, but I don't have the space OR the money for one.The instruction manual was worthless, but luckily assembling the press was intuitive. However, the manual would be good for ordering replacement parts if needed. There is a nice breakdown of the parts that are included in the kit. Before ordering, make sure it is compatible with your unit, it is clearly stated what models the press is compatible with.This was an excellent purchase for $40!!

    @user-yc1mc4bu6q@user-yc1mc4bu6q7 ай бұрын

  • Молодец дал вторую жизнь станку и продлил память о СССР.

    @user-uc6cg1hv4f@user-uc6cg1hv4f4 ай бұрын

    • 🤮

      @user-hf7mr1vv9e@user-hf7mr1vv9eАй бұрын

  • Now there is the addition of a much needed tool! Marvelous!

    @publicclammer@publicclammer Жыл бұрын

  • Well done!! I like the choice of a hammered finish to hide casting imperfections. I also applaud your use of sealed bearings to replace the old open bearings in the motor and in the spindle. I'm glad that the quill was in good shape so that you didn't have to tackle restoring that, they can be a real pain. Overall excellent workmanship.

    @williamstyers4264@williamstyers4264 Жыл бұрын

  • К нижеупомянутым не аутентичностям я бы еще добавил шильдик, нужно было тоже восстановить. А вообще - Отличная работа!!!

    @Tsar77@Tsar77 Жыл бұрын

    • Все три таблички (большая с названием, средняя с оборотами и маленькая «заземление») заказал на Авито еще перед Новым годом, где то еще едут. Спасибо.

      @ITBR_Restoration@ITBR_Restoration Жыл бұрын

    • @@ITBR_Restoration Прямо от сердца отлегло, так расстроился за шильдики.

      @user-jf7cd8xp3c@user-jf7cd8xp3c Жыл бұрын

  • Nice refurbishing project. Every shop has to have a drill press. You did very good making it look great and run well too... Thumbs Up!

    @garymucher4082@garymucher4082 Жыл бұрын

    • thanks for the support! You are right, it is difficult to do without this machine in the workshop.

      @ITBR_Restoration@ITBR_Restoration Жыл бұрын

  • Great job it's good to see machines get a refit instead of throwing it away in this world of ours of just buy a new one Regards Steve UK London

    @stevefromlondon9175@stevefromlondon9175 Жыл бұрын

    • Thank you. This machine is very old, but it is of excellent quality, it has an excellent margin of frame rigidity and engine power. I think that a modern analogue will cost quite a lot!

      @ITBR_Restoration@ITBR_Restoration Жыл бұрын

  • Wonderful restoration, even without the decals, and you have it working nicely thank you.

    @terryrogers1025@terryrogers10256 ай бұрын

  • Very nice to see this old machinery get a new life.

    @SODAK2276@SODAK227610 ай бұрын

  • Nice job. I’ve always been afraid to re-do older industrial type machinery but you make it look easy 😊 Thanks for sharing.

    @restorerestoration4705@restorerestoration4705 Жыл бұрын

    • @@jaydouglas-up7fv 😀

      @restorerestoration4705@restorerestoration4705 Жыл бұрын

  • Very Beautiful! I like how U cleaned the wiring with the addition of a clean on/off button. Nice color combination. U turned it into a usable piece of art

    @davidgardner4940@davidgardner4940 Жыл бұрын

    • Thank you! In the workshop, this machine is a very important element.

      @ITBR_Restoration@ITBR_Restoration Жыл бұрын

  • Thank you for not making 1/3 of your video sandblasting. Love the colors you picked.

    @bfg1637@bfg1637 Жыл бұрын

    • Thank you for watching. I also got fed up with the sandblasting footage in the video.

      @ITBR_Restoration@ITBR_Restoration Жыл бұрын

  • Splendid job. I would have retained the gear-lever knob as a souvenir. :)

    @victorlaiviera9683@victorlaiviera96837 ай бұрын

  • Mis felicitaciones por esa restauración y darle nuevamente vida a ese taladro,saludos desde Argentina

    @andresscaglia9134@andresscaglia91347 ай бұрын

  • Просмотрел не отрываясь,это не работа,это симфония!Эх,повезло станочку,в такие ручки попал!

    @user-oy5ji2nc8l@user-oy5ji2nc8l Жыл бұрын

    • Спасибо за добрые слова 👋

      @ITBR_Restoration@ITBR_Restoration Жыл бұрын

  • Excellent job and an inspiraton for us all. You did not use fancy tools in the renovation (except a lathe perhaps and a sand blaster) ...you show what can be done with effort. Well done.

    @frankowen@frankowen Жыл бұрын

    • Thanks for the words of support. In my first videos, I used the smallest set of tools (I only dreamed of a sandblaster and a lathe). So you are right, with a strong desire, you can work with the simplest tool.

      @ITBR_Restoration@ITBR_Restoration Жыл бұрын

  • Amazing work!

    @joshuaosburg3618@joshuaosburg3618 Жыл бұрын

  • Собрался уже поворчать на некоторые небрежности, потом увидел, что это восстановление не для понтов, а для работы. ))) А про провод вам уже написали. Тоже люблю покрытие молотковой эмалью. Красиво получилось!

    @ShtankoPavel@ShtankoPavel Жыл бұрын

    • Спасибо за комментарий! Действительно, делал для себя, для частого использования, поэтому некоторые моменты во внешнем виде, упущены.

      @ITBR_Restoration@ITBR_Restoration Жыл бұрын

  • *_Better and much more beautiful than new!! Good job_*

    @RestorationVideo@RestorationVideo Жыл бұрын

    • 👍👍👍😉

      @ITBR_Restoration@ITBR_Restoration Жыл бұрын

  • Im just about to restore a very similar one! Thanks for the inside look before I take mine apart :)

    @MrRevell13@MrRevell1311 ай бұрын

    • I'm glad you found my video helpful.

      @ITBR_Restoration@ITBR_Restoration11 ай бұрын

  • Nice job. Maybe this will get me to fix my drill press. Thank you.

    @raymondmartin7130@raymondmartin71305 ай бұрын

  • Great job! Lada gearshift knob😊

    @scottrobinson3281@scottrobinson32817 ай бұрын

  • Gorgeous work

    @gergemall@gergemall Жыл бұрын

  • Работа хорошая. Возможно стоило сделать полноразмерный кожух на верхнюю часть станка, а не ограничиваться щитком спереди. Так же отмечу довольно опасный изгиб питающего провода идущего в блок с кнопками управления, в относительной близости от вращающихся деталей.

    @umbrellasebastiansanchez9094@umbrellasebastiansanchez9094 Жыл бұрын

    • Спасибо за вашу оценку. С завода изготовителя у этих станков устанавливался именно щиток спереди (была другая форма, в виде перевернутого чугунного горшочка), поэтому решил что для личного использования мне достаточно и щитка. Кабель довольно жесткий и я надеюсь не будет, (без посторонней помощи😁) лезть во вращающиеся детали 😁

      @ITBR_Restoration@ITBR_Restoration Жыл бұрын

  • Молодец!Очень грамотная покраска и сборка!

    @user-tl4jw2ki7n@user-tl4jw2ki7n8 ай бұрын

  • Fabulous restoration

    @RestorationsFOD@RestorationsFOD7 ай бұрын

  • Great video. Excellent restoration

    @joe1569@joe1569 Жыл бұрын

    • Thanks 🙏🏻

      @ITBR_Restoration@ITBR_Restoration Жыл бұрын

  • Excellent job.

    @nardaoeletronica@nardaoeletronica Жыл бұрын

  • Great restoration job and has given me some food for thought. I'm part way through the exact same thing myself on an old large format, heavy duty pillar drill I was donated by a late friend. My problems are that: 1. Mine seems to be considerably heavier with a massive cast body weighing about 20kg stripped of all parts!! The drill fully assembled was a real struggle to get up on the bench to dismantle. 2. It has a 60cm column which took a LOT of persuading to separate it from the body but now the large cast iron base collar won't budge. I think it is going to have to have one of my special citric acid baths for several days then the old heat and candle wax trick to separate it. 3. There is no base and no table, plus no rack/pinion lift. Consequently I'm having to think carefully about what to use. I'm currently thinking of a thick piece of granite for the base as finding a cast iron one seems remote as well as prohibitively expensive. Even a 1" steel plate would be quite expensive whereas I can get granite offcuts fairly cheaply and drilling using diamond core drills is no problem at all. Counterbores are a bit challenging but even they are not too bad. 4. The lack of a table and no rack and pinion lift also needs addressing and a retrofit of some kind seems inevitable. I can live without a table IF I can get/fit a suitable rack and pinion to take what will be approx 40kg with all the bits and a motor mounted 5. I never had a motor with it but I have a VERY good condition, as new, 3 phase, 2.5 HP motor that I plan to use with a suitable single to 3 phase 5HP capable VFD I already have. 6. The large 1/2" Jacobs chuck that came with it was rusted solid but that was citric acid soaked for a week and then stripped & cleaned and now looks really good. 6. The quill seems in good shape but I plan on replacing all the bearings as you did and using proper rubber sealed units. I can never understand why companies fit steel sealed or even non sealed bearings when, even retail, bearings are so little cost. 7. The quill return spring proved to be broken on dismantling but a new one was easy to obtain from Ali Express. I wish I had access to a sand/bead blaster like you have. I could do a great and quicker job of stripping all the bits back to base metal rather than wire brushing/flap wheeling/Scotchbriting that I have to do. I just have to dedicate some time to it once the weather gets a bit warmer - my shed has no heating and it's been -4°C during the day which is VERY cold for the UK at this time of year. Once again, a great job done and a really nice set of paint jobs and overall restoration! I hope mine turns out as well.

    @boblewis5558@boblewis5558 Жыл бұрын

    • First, I'm amazed at the text size of your comment. YOU have spent a lot of time to write all this, you have great patience (unlike mine 😁) Secondly, you are right about the sandblaster. It makes the job much easier and faster. If you watch my earlier videos, I mainly used electrolysis to remove rust, as well as a brass brush and grinder attachment. Thirdly, working in the cold is not at all pleasant. Although my workshop is heated, but when it is minus 25 Celsius outside, the temperature in the workshop drops to plus 10, and I don’t feel like doing anything with my hands at all. I am sure you will succeed with your machine, you can handle it. And when you're done, I'd love to take a look at it. Can you send a couple of photos by email? My email is in the channel description.

      @ITBR_Restoration@ITBR_Restoration Жыл бұрын

    • @@ITBR_Restoration thanks and I certainly shall! 👍

      @boblewis5558@boblewis5558 Жыл бұрын

  • Awesome always cool stuff always thanks 😎

    @charlesstarlin6354@charlesstarlin6354 Жыл бұрын

  • Looks great, I like the design of the head moving up and down rather that just the table on mine.

    @cm5838@cm58383 ай бұрын

    • 👍👍👍

      @ITBR_Restoration@ITBR_Restoration3 ай бұрын

  • Well done! 👍🏼

    @DrHutOfHandcraft@DrHutOfHandcraft Жыл бұрын

  • Проделана хорошая работа. Единственное, что я бы советовал: при сборке использовать не пластичную смазку, а ту же веретенку (индустриальное масло). Это обосновано тем, что при работе на станках образовывается пыль (помимо стружки) из тех материалов, которые обрабатываются. Она очень хорошо загустевает в пластичной смазке и коксуется в одних местах и изнашивает движущиеся детали в других местах. Некоторые узлы лучше и вовсе не смазывать (патрон токарника, например), либо смазать твёрдым графитом. На тех же Волгах старых шкворни лучше смазывать жидким маслом, чем пластичной смазкой (по тем же причинам что выше описаны). Допустим при следующем цикле ручной смазки ты прокачиваешь или проливаешь узлы жидким маслом и все гадости вымываются постепенно (можно, конечно, и проникающими смазками аля ВД40). Это все, конечно, при условии, что узел не защищён пыльниками или сам по себе не является герметичным.

    @Mechanic_Simulator@Mechanic_Simulator Жыл бұрын

    • Насчет смазки токарного патрона категорически не согласен. Также не согласны мои патроны, в т.ч. Bizon, имеющие масленки с завода для смазки передней части улитки. А внутрь патрона, со стороны сателлитов, закладывается консистентная смазка.

      @RZ296@RZ2965 ай бұрын

  • В СССР техника делалась на века! А если еще чуть поработать напильником получится - гранатомет!

    @user-or1hp3nc2e@user-or1hp3nc2e Жыл бұрын

    • Это точно 😂

      @ITBR_Restoration@ITBR_Restoration Жыл бұрын

  • Quality work

    @andyblyth923@andyblyth923 Жыл бұрын

  • Great job. What kind of grease did you use, never seen blue grease before.

    @lrdisco2005@lrdisco20052 ай бұрын

  • Masterfully done - stunning results! I love to see what appears to be “junk” restored to original condition & purpose. Thank you!

    @ronstudd3788@ronstudd37887 ай бұрын

  • Молодец, Крутая работа, но нужны инструменты посовременней, и зря не показал монтаж и подключение проводки. Продолжай в том же духе!!

    @178Spooner@178Spooner Жыл бұрын

    • Спасибо! Инструменты потихоньку подкупаю👍. Проводку не стал показывать, показалось что там ничего интересного не было.

      @ITBR_Restoration@ITBR_Restoration Жыл бұрын

  • Very nice restoration

    @tombarlow6176@tombarlow6176 Жыл бұрын

  • You have to show the sand blasting. It will bring you a lot of subscribers.

    @andresarmento7227@andresarmento72277 ай бұрын

  • Très beau travail de restauration et bien filmé. Félicitations !

    @titofernandezmeirino9832@titofernandezmeirino9832 Жыл бұрын

    • Merci d'avoir regardé et pour votre soutien !

      @ITBR_Restoration@ITBR_Restoration Жыл бұрын

  • Excellent work Bro.⭐️⭐️⭐️⭐️⭐️

    @jamescraig5421@jamescraig5421 Жыл бұрын

    • Thanks Bro!!!👍

      @ITBR_Restoration@ITBR_Restoration Жыл бұрын

  • Просто потрясающе.

    @user-yw8rj7wx5s@user-yw8rj7wx5s Жыл бұрын

  • Well done.

    @RestorationAustralia@RestorationAustralia Жыл бұрын

  • REALLY GOOD WORK DUDE !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

    @carlmcgee1623@carlmcgee1623 Жыл бұрын

  • Ну просто респект и уважуха за такую работу)))

    @mikhalych59@mikhalych59 Жыл бұрын

    • Спасибо 👍

      @ITBR_Restoration@ITBR_Restoration Жыл бұрын

  • У тебя тиски есть, а ты подшипники садишь ударами молотка. И посадочные места под валы и подшипники красить - так себе идея. Но всё равно красиво получилось. Лайк.

    @user-sv5oq1bd1t@user-sv5oq1bd1t5 күн бұрын

  • MAGNIFIQUE!!!!!!!!!!!!!

    @freedom020@freedom020 Жыл бұрын

  • Хороший станок! Отличная работа!!! 🤝🤝🤝

    @user-raf-kat@user-raf-kat Жыл бұрын

    • Благодарю за поддержку! Я долго откладывал ремонт этот станка, но он мне сильно пригодится для создания следующего видео.

      @ITBR_Restoration@ITBR_Restoration Жыл бұрын

    • @@ITBR_Restoration Уже весь в нетерпении ! 👋😁👏👍

      @pavelmeridian3428@pavelmeridian3428 Жыл бұрын

  • This was Epic ... respect.

    @nordicson2835@nordicson2835 Жыл бұрын

    • Thanks for support!!!🙌🙌🙌

      @ITBR_Restoration@ITBR_Restoration Жыл бұрын

  • Looks very similar to my Craftsmen drill press. "Restoring" mine required just removing light surface rust.

    @That70sChannel@That70sChannel9 ай бұрын

  • отлично получилось, я в прошлом году на металлоприёмке почти такой же станок купил, только без мотора и состояние на много хуже, но ни чего работает уже )

    @user-nl3rn2hc9b@user-nl3rn2hc9b Жыл бұрын

    • Отлично👍! Меня поражают люди, которые сдают на металл такие вещи!!!!

      @ITBR_Restoration@ITBR_Restoration Жыл бұрын

  • кожух защитный плоховат.можно было полноценным сделать.Да и детали лучше в тисочках зажимать, а не в клещах.А в целом работа супер !

    @user-uk1fp7dt8q@user-uk1fp7dt8q7 ай бұрын

  • Excelente trabalho !!!

    @adeilson701@adeilson701 Жыл бұрын

    • 🤗🤗🤗

      @ITBR_Restoration@ITBR_Restoration Жыл бұрын

  • Прекрасная работа!!! Но подшипники стоит проверять на присутствие смазки. Я обжигался на этом.

    @user-kj5kw7ue7y@user-kj5kw7ue7y Жыл бұрын

    • Спасибо за поддержку! Подшипники покупал не из дешевых))) поэтому надеюсь на совесть производителя)

      @ITBR_Restoration@ITBR_Restoration Жыл бұрын

  • essa pintura a mão ficou sensacional

    @valderjanzentaveiradasilva9819@valderjanzentaveiradasilva98197 ай бұрын

  • Fantastic restoration good for another 50 or more years I'm a new subscriber...

    @robertcolfack26@robertcolfack26 Жыл бұрын

    • Thanks for subscribing!!! On Monday or Tuesday I will post a new video, I will be glad if you watch it !!!

      @ITBR_Restoration@ITBR_Restoration Жыл бұрын

  • Ой, если честно, я прям заждалась ваше видео🙌🏻. В этот раз чуть позже обычного опубликовали. Работа отличная, прям новую жизнь дали этому прибору 🤟🏼👍🏻💫

    @lavotaro@lavotaro Жыл бұрын

    • Вибратор - это прибор, а на видно станок.

      @vladanufriev@vladanufriev Жыл бұрын

    • @@vladanufriev вам виднее 😂

      @lavotaro@lavotaro Жыл бұрын

    • @@lavotaro у вас станок, у нас прибор 🤣🤣🤣

      @user-yf5nh7iy8m@user-yf5nh7iy8m Жыл бұрын

  • Good job.

    @suadcokljat1045@suadcokljat1045 Жыл бұрын

  • Nicely done. If we're me though, I would have gone looking for two more bear shift knobs... 😄

    @robertfranklin5523@robertfranklin5523 Жыл бұрын

  • Excellent travail, BRAVO ! 👍

    @JC-sc4il@JC-sc4il Жыл бұрын

  • Maan, that was one Frankenstein of a drill. The shifter was cool though.

    @homeyshlitz@homeyshlitz Жыл бұрын

  • super travaille et bon montage vidéo ! bravo !!!

    @pascaldurand8083@pascaldurand8083 Жыл бұрын

    • Спасибо за просмотр и поддержку!

      @ITBR_Restoration@ITBR_Restoration Жыл бұрын

  • Ficou perfeito, parabéns

    @RegiPavan@RegiPavan5 ай бұрын

  • thats very impressive😮

    @mattewclubb5882@mattewclubb5882 Жыл бұрын

    • Thanks for your support!

      @ITBR_Restoration@ITBR_Restoration Жыл бұрын

  • It would be great to see the sandblasting. It's one of the best things to watch

    @jools182@jools182 Жыл бұрын

  • Perfeito parabens

    @carlosrodrigues1467@carlosrodrigues146710 ай бұрын

  • Well done

    @19Bmiller@19Bmiller Жыл бұрын

    • 👍👍👍

      @ITBR_Restoration@ITBR_Restoration Жыл бұрын

  • Все отлично, но выбивается не аутентичные пуск/стоп.

    @user-kr5pe4og1n@user-kr5pe4og1n Жыл бұрын

    • Спасибо. Аутентичные сейчас в дефиците))), не смог найти.

      @ITBR_Restoration@ITBR_Restoration Жыл бұрын

  • Very awesome work! Good to see you wear gloves when necessary but not afraid to show you get dirty (or injured). In older videos, the subtitles are in cryllic or are missing. Would it be possible to go back and change that?

    @Immortalaquarius@Immortalaquarius Жыл бұрын

    • Thank you! It is very inconvenient to work with gloves, but sometimes you simply cannot do without them. In which of the old videos did you have problems with subtitles?

      @ITBR_Restoration@ITBR_Restoration Жыл бұрын

  • Muy buen trabajo. Felicidades.

    @ldemiguelrodrigo3204@ldemiguelrodrigo3204 Жыл бұрын

    • ¡Gracias por mirar y por su apoyo!

      @ITBR_Restoration@ITBR_Restoration Жыл бұрын

  • Very nicely done, although I think I would preserve every plate with writing on it that was on the machine.

    @jozsefizsak@jozsefizsak Жыл бұрын

    • Don't worry about the labels. I installed all the new ones and posted a photo in the "Community" tab, I will be glad if you look !!

      @ITBR_Restoration@ITBR_Restoration Жыл бұрын

    • @@ITBR_Restoration Very nice!

      @jozsefizsak@jozsefizsak Жыл бұрын

  • Работа отличная Удачи!!

    @-159.4vmm_vova_s.@-159.4vmm_vova_s. Жыл бұрын

    • Спасибо за поддержку! Вам тоже желаю удачи!!!

      @ITBR_Restoration@ITBR_Restoration Жыл бұрын

  • Auch wenn du ein Russe bist? Super gemacht! Du hast es wieder bewiesen das Mann aus Sch…. Gold machen kann! 👏🏼👍🥇 Mach weiter so und bleib gesund 🍀

    @leahcimressik5994@leahcimressik5994 Жыл бұрын

  • Отличный станок!! Отличная реставрация!! Стал лучше чем новый!!!! 💯🔥

    @user-ct9wp3uo5l@user-ct9wp3uo5l Жыл бұрын

    • Спасибо за просмотр и поддержку👍👍👍

      @ITBR_Restoration@ITBR_Restoration Жыл бұрын

  • Bel lavoro e vernici appropriate 👍

    @maurozacchia8973@maurozacchia8973 Жыл бұрын

  • Отличный станок получился. Теперь я знаю каких деталей не хватает на моём точно таком же.

    @user-nl2vr8pc1n@user-nl2vr8pc1n Жыл бұрын

  • Excelente, muy bueno

    @nelsoncarta9351@nelsoncarta9351 Жыл бұрын

    • 👍👍👍

      @ITBR_Restoration@ITBR_Restoration Жыл бұрын

  • The old girl lives to fight another day, it came out beautifully

    @christurner5473@christurner54736 ай бұрын

  • Great restoration man! Love the hammer effect paint! EDIT: Subbed.

    @GordiansKnotHere@GordiansKnotHere Жыл бұрын

    • Hammer effect paint always looks great on cast iron and melted parts .

      @raoulvolfoni1800@raoulvolfoni1800 Жыл бұрын

    • If you paint a cast-iron product from a spray gun, then you emphasize all the surface irregularities. And the hammer effect paint hides all the flaws.

      @ITBR_Restoration@ITBR_Restoration Жыл бұрын

  • Ótimo muito bem trabalhado 👏👏👏👏 Br

    @tarciliobeneditodasilvafil3921@tarciliobeneditodasilvafil3921 Жыл бұрын

    • Спасибо ☺️

      @ITBR_Restoration@ITBR_Restoration Жыл бұрын

    • olá brazuca

      @edinhofragelli@edinhofragelli11 ай бұрын

  • Great job on a real beat up drill press. I think you should try to make a better belt guard though Should have maybe just power washed the whole thing before taking it apart - less work.

    @craigsmith3645@craigsmith3645 Жыл бұрын

  • Тема шпинделя не раскрыта! ) Я тех подшипников рот шатал!

    @mrvm07@mrvm0710 ай бұрын

  • НС-12 очень повезло, хорошая работа!

    @MrLezhenin@MrLezhenin Жыл бұрын

    • Спасибо за оценку 👍

      @ITBR_Restoration@ITBR_Restoration Жыл бұрын

  • Great job as usual thank you for the video.

    @smitzinok@smitzinok Жыл бұрын

    • Thanks for watching and for your support!

      @ITBR_Restoration@ITBR_Restoration Жыл бұрын

  • Человек славно потрудился!!! 👍✊ Вопрос: что за смывка (возможно неправильно назвал) в баллоне?

    @user-qc3tf4jr8b@user-qc3tf4jr8bАй бұрын

    • благодарю! смывка краски "Dekorix", только ей и пользуюсь.

      @ITBR_Restoration@ITBR_RestorationАй бұрын

    • @@ITBR_Restoration 🤝

      @user-qc3tf4jr8b@user-qc3tf4jr8bАй бұрын

  • Very nice. 👍. Did you use a wire brush to remove the green paint?

    @stuartkorte1642@stuartkorte1642 Жыл бұрын

  • Fantastic work, wish you showed the sandblasting. It’s fun to watch the sandblasting

    @ialaddin@ialaddin Жыл бұрын

  • great job on 1969 kamunaras drill press restoration awesome results restoration in the back room 😍😍😍😍😍😍😍😍😍😍😍😍😍😍😍😍😍😍😍😍😍😍😍😍😍😍😍😍😍😍😍😍😍😍😍😍😍😍😍😍😍😍😍

    @julienghanadan8311@julienghanadan8311 Жыл бұрын

    • 🤗🤗🤗🤗🤗🤗🤗🤗

      @ITBR_Restoration@ITBR_Restoration Жыл бұрын

  • Ką tu, staklikės kaip naujos :)

    @zoidberg552@zoidberg552 Жыл бұрын

    • O, ačiū!

      @ITBR_Restoration@ITBR_Restoration Жыл бұрын

  • Great job, what lathe are you using🤔🤔

    @niallcollins2493@niallcollins2493 Жыл бұрын

  • Very good

    @amirheydari3246@amirheydari3246 Жыл бұрын

    • Thanks 🙏🏻

      @ITBR_Restoration@ITBR_Restoration Жыл бұрын

  • You should use hammerite paint looks really good

    @PeterPerez.@PeterPerez. Жыл бұрын

    • Yes thank you.

      @ITBR_Restoration@ITBR_Restoration Жыл бұрын

  • Incroyable

    @bebel6874@bebel6874 Жыл бұрын

    • 🤗🤗🤗

      @ITBR_Restoration@ITBR_Restoration Жыл бұрын

  • great job !!! whenever you want to put a bearing on a shaft, the BEST solution is to heat it at 80 deg C with a hair dryer or a heat gun (no flame, torch...). it will slide on that shaft very easily. at that temperature no damage it is done to the bearing ! why you didn't sandblast also the other parts ?

    @fly3209@fly3209 Жыл бұрын

  • From number wire coming on the motor you have 3 speed motor giving a total of 15 speed with belt one set will be low speed, the other set will be medium speed and 2 power together will be high. It Looks good, I do think a powder coat paint would’ve looked better but that’s my personal opinion.

    @jerrygaguru@jerrygaguru Жыл бұрын

  • I'm surprised you didn't sand the stator. Not that it isn't a big deal. I just thought it might help. But what do I know!!😉😃

    @anthonysammartino1654@anthonysammartino16548 ай бұрын

  • Суровый был станок! Кто-то на него даже ручку переключения скоростей от грузовика поставил :) 6 скоростей, 5 вперёд и 1 назад, как на КамАЗе, может где-то ещё такие есть.

    @user-pe5rf3kd9x@user-pe5rf3kd9x Жыл бұрын

  • Как раз и меня есть точно такой-же, работает отлично,

    @user-ep5et2gc4u@user-ep5et2gc4u Жыл бұрын
KZhead