Tried this once. Problem: Friction generates heat, which melts glue, which ends pretty little rolls of sand paper.
@briansmith8999 Жыл бұрын
What you on about? He didn’t use no glue!
@jp-wd9qy11 ай бұрын
Генитально! Как только вижу термоклей, понимаю, будет ненужная самоделка.
@evgenyrepkin9930 Жыл бұрын
плавкий клей нагрелся и все разлезлось
@user-vp3rs1so9q Жыл бұрын
😅
@defraivagad7429 Жыл бұрын
💯
@user-dc6bk9bx9p Жыл бұрын
Супер, правда термоклей отклеивается от тепла
@arthiarthubald6101 Жыл бұрын
Вообще пофигу, там исполуется бумажная наждачка, она распадется быстрее чем нагреется клей
@Alleksandr_Gamer Жыл бұрын
похоже.чел.давно.в.магаз.не.ступалл
@user-df8zk5is1q Жыл бұрын
Хрень полная , секунд на 30 работы , дальше клей разогревается и все идет по одному влажному месту .
@bez_be Жыл бұрын
Всё! Завтра же с утра за вином!
@slavamostovoy3773 Жыл бұрын
Я тоже ,,
@nedeljkoperic9481 Жыл бұрын
Огурцы и contex не забудьте докупить!!!
@Alleksandr_Gamer Жыл бұрын
термоклей хрень полная нагреется и распадётся
@Armgorec Жыл бұрын
Хорошая самоделка! Вот только есть вопрос: А больше 2 минут она проработает?
@fergeron_druidych Жыл бұрын
U tebia malo probok ot vina???? Ili dorogu do magazina snegom zamelo?
@sakoupa Жыл бұрын
Slick. The tightening of the nut/washer provides compression that holds the sandpaper.
@jimparsons6803 Жыл бұрын
Well done buddy. We hadn't worked that one out.
@wiccanwarrior9 Жыл бұрын
Исполнение дерьмо. На таком биении ничего не сделаешь.
@user-gv8il4gc4z Жыл бұрын
Идиотовидео
@rasha.idi.na.xu. Жыл бұрын
Но это легко устранимо с помощью той же дрели.Потом по размеру склеить бумагу и вперёд))
@vladimirvladimir1412 Жыл бұрын
и термо клей вариант говно.
@user-jj3fo3ni8z Жыл бұрын
@@user-jj3fo3ni8z можно взять покрепче, найрит, ПВА- д3, 88-й , суперклей не самый дешёвый , и ок !💪
@user-hh1gh6yo8d Жыл бұрын
Отлично! Есть повод сбегать в магазин за бутылочкой вина. Лучше 2 возьму. На вторую пробку наждачку мелкозернистую. 😀
@nemoerambler4749 Жыл бұрын
бери сразу ящик.ну шоб сто раз не бегать
@user-do5ze4ub9k Жыл бұрын
@@user-do5ze4ub9k Убедил. Новый годна носу, не пропадет. Да и пробок на год хватит😀 С наступающим.
@nemoerambler4749 Жыл бұрын
Fantastic is an idea of a genius!!
@filippooreglia2602 Жыл бұрын
you should mount a wing nut, to facilitate the replacement of the abrasive cylinder🤗
@alleentochvrij9253 Жыл бұрын
And possibly use larger washers on the cork. It might compress better.
@dancahill8199 Жыл бұрын
Por fin..... Algo funcional.... Felicitaciones.... 👍
@leopoldopolo5195 Жыл бұрын
Мой кот тоже яйца лижет,когда делать нечего....
@alexirbis5747 Жыл бұрын
Весь в тебя
@jason22jj Жыл бұрын
А у меня, как у человека армейского, собака красит будку
@user-lq7gc1vk9x Жыл бұрын
What a innovation he has to be awarded noble prize 🏆
@saisankar.m2580 Жыл бұрын
Nobel Prize
@RErnie-gv1hv Жыл бұрын
А то, что спермоклей от нагрева теряет свои свойства- никто не думает. Доктора в студию!!!
@ddr.club_WBT_1 Жыл бұрын
Это заявка для доктора дью. Срочно позовите доктора!
@termit1735 Жыл бұрын
Нафиг надо, надоели эти кринжовые самоделки у него в видео. Лучше пусть что-то более интересное разбирает
@Chewed_Mole Жыл бұрын
Бьёт. Надо было сначала пробку просверлить, зажать болт, в шурик и обточить пробку, а уже потом мотать и клеить наждачку.
@Anton..A Жыл бұрын
Ага, и не а сопли клеить, которые при нагреве поплывут
@deniszuzu9310 Жыл бұрын
thank you. The only problem I have is, after I drink that whole bottle of wine, I can't faribikate nuttin.
@calvincosby921 Жыл бұрын
True but you no longer care.
@RErnie-gv1hv Жыл бұрын
A great idea.. But unless you have a load of pipes to clean up it's easier by hand. But the idea is great and simple and I'll use it for other sanding jobs that will be more suited to this type of sanding wheel. Well done and thanks for the great video.
@jimheriotspence5649 Жыл бұрын
Jim let’s be honest, you’ll never use this idea. You’re a nice guy Jim, But you’re not nice enough to use this idea. Jim have a good 2023 my good friend
@sho7gunx63 Жыл бұрын
Молодец какой, я не додумался 😊😊😊
@user-jt3it6dy8m Жыл бұрын
Clever, very clever, my friend! Thanks. ✔
@johnathansmith3819 Жыл бұрын
Есть приспособа лепесток, без этих заморочек, и работает супер!
@user-rw1mp9ng2y Жыл бұрын
Док, настало твое время!
@gorshookgorshohek1526 Жыл бұрын
Опередил 😄
@mobivlad33 Жыл бұрын
хорошая приспособа,пригодится.👍
@user-hp2kz4si1o Жыл бұрын
Да, только как спермоклей нагреется всему пиз*а
@andyvillage6857 Жыл бұрын
@@andyvillage6857 ,спермоклей использовать не будем,я подумал что можно сделать на липучку.
@user-hp2kz4si1o Жыл бұрын
Dude you are a genius
@2Jeezuzisreal Жыл бұрын
Не смущает что это будет нагреваться и термо клей не будет держать 😂
@user-rc5jr8my5k Жыл бұрын
Криво просверлил, нужно было зажать сверло, а вращать пробку.
@user-jw9yz7gs9v Жыл бұрын
You do know Dremel makes pretty much the same thing, probably works a lot better too
@Antharion Жыл бұрын
And with the time ,the bottle of wine the nut bolt most likely cheaper too
@willyswagon57 Жыл бұрын
I bet the sandpaper slips on the cork. It’s also a good idea to drill the hole in the exact center of the cork.
@pedro_sanchez.80 Жыл бұрын
Not THAT long and more costly, though.
@johnathansmith3819 Жыл бұрын
Drum sander set of 5 for about 10 bucks!
@wiccanwarrior9 Жыл бұрын
делитант,Я прав мужики?
@user-jm4py2fw3o Жыл бұрын
Нет. Правильно: дилетант.
@stell33.stell33 Жыл бұрын
на 107%
@user-gf4bf3hl4k Жыл бұрын
Finally a homemade tool I might actually use
@Slowhand871 Жыл бұрын
No, the glue heated up from friction and everything fell apart
@Lupuzs Жыл бұрын
lol
@mtraven23 Жыл бұрын
Гениально. Никогда бы не додумался.
@user-ns4tf3xb1t Жыл бұрын
Очумелые ручки
@MSK-tv4ml Жыл бұрын
Если термоклей не отклеится (не допускать нагрева) - вполне удачная идея.
@DomNaPechi Жыл бұрын
Где же вас, таких гениев находят???
@user-js8xy2zl9d Жыл бұрын
Нобелевскую премию в студию
@el_brigadir Жыл бұрын
Lo encontre genial te felicito...
@rafaelaguayopinochet8211 Жыл бұрын
Great idea! I live on winery row (it’s way out of hand here) in central Texas, and have large trashbags full of corks, and no I don’t drink! 😂 I make topwater lures, among other useful things. Going to add this, and some other modifications for buffers etc. to my list. Really appreciate you sharing your ingenuity. Happy New Year! 👍👍👌
@charlieboutin3341 Жыл бұрын
By the time you make this you could have had the entire project done!
@elroygolightly1104 Жыл бұрын
после таких операций можете попрощаться с подшипниками шпинделя и муфты. шуруповёрт это долго терпеть не станет, он все таки не на это рассчитан.
@kombatshock8158 Жыл бұрын
Ideen muss der Mensch haben👍👍👍👍
@ilseheiland4205 Жыл бұрын
Been doing this for 20 years . Should leave a longer tail on sandpaper for longer before it wears out
@michealbleys2212 Жыл бұрын
tightening the nut expands the cork to grip the abrasive tighter. good one
@marcuscicero9587 Жыл бұрын
Putting the device in a drill makes the hot glue melt. A roll on emery paper and some elbow grease saves a lot of time
@turboduckhead6179 Жыл бұрын
@@turboduckhead6179 Copied from existing drum sander sets.
Есть способ гораздо проще. Делаем на шпильке продольный рез болгаркой. Вставляем наждачку в разрез и наматываем ее на шпильку. ВСЁ. Ну и естественно потом в шурика вставить.
@HDR_HDS Жыл бұрын
It's cheap enough, I'll just buy it.
@richardcurtis2688 Жыл бұрын
Идея хорошая, но термоклей не подойдёт, потому что нождачка нагреется и клей расплавится,
@monolit5610 Жыл бұрын
Пробка вращается,а шкурка на месте ,поэтому не забудь клей
@farida7015 Жыл бұрын
Wow.👍
@zfreedom4582 Жыл бұрын
فكرة بسيطة وسهلة وحلوة..
@user-vm9ch6ee9c Жыл бұрын
Excellent idea. Far cheaper than buying sanding drums.
@daver8298 Жыл бұрын
These won't last 5 mins buddy.
@wiccanwarrior9 Жыл бұрын
Есть намного проще решение. На заводе мы называли это - вертолёт)
@AlainDelon74 Жыл бұрын
Wow! Wonderful idea!
@vetsfreepress2144 Жыл бұрын
Zajefajny pomysł 👍🇵🇱
@starybasiorswietokrzyski5859 Жыл бұрын
This is very helpful thanks
@rubensalais1502 Жыл бұрын
Buena la idea pero así se desperdicia mucha lija para utilizar el otro extremo nececita romper la lija para quitar el pegamento
@javierdavilamartinez818 Жыл бұрын
Стык нужно делать по диагонали и лучше без нахлеста, и не на термоклей
@azvedy7395 Жыл бұрын
Thank you for reminding me I have to call Spectrum cable
@jerrydawg4434 Жыл бұрын
Excelent
@romildomonteiroferreira1940 Жыл бұрын
Пробка в тисках - это сильно! С руки сверлить - тоже... про центровку и биение промолчим. Сопли термические... ой.
@polurich9968 Жыл бұрын
A 1965 hack !! Awesome dude!
@josesantos222 Жыл бұрын
i like it
@annaqojimDigital Жыл бұрын
Quicker and Cheaper to buy than to make.
@thomasbuckley37 Жыл бұрын
Здорова! Глупый момент. Трубочка с разрезом и лентой наждачки проще и лучше.
@user-zo1hj2wz3z Жыл бұрын
хрень, нагреется и отклеится!
@user-my1dv7kb4d Жыл бұрын
Трубу проще лентой обвернуть и ручками
@mrpitonchik Жыл бұрын
Awesome an actual tool thats useful . Maybe the first video like this that's actually worth the watch
@Aprilfool4121 Жыл бұрын
Or you go buy one for $3 a save time and supplies that are worth more 😂
@henryhenry3832 Жыл бұрын
@@henryhenry3832 You'd be the type to save a cork ,a piece of all thread and 2 washers and nuts huh. A dollar saved is a dollar earned.
@Aprilfool4121 Жыл бұрын
@@henryhenry3832 or you don't know how big of a wast of money buying crap like this is when you have 200ft roll of sandpaper laying around
@Aprilfool4121 Жыл бұрын
@@Aprilfool4121 only if you’re time is worth nothing, mine is worth $115 per hour, so I would rather buy a $3 flapper wheel and save my customers a lot of money
@henryhenry3832 Жыл бұрын
@@henryhenry3832 you do you dude.
@Aprilfool4121 Жыл бұрын
Сначала купить бутыль вина чтобы появилась пробка. А далее... дануНах эту самоделку, надо идти за следующей.....
@ksv_072 Жыл бұрын
Soon as he started using hot glue I knew, engineer. But then when he started drilling a cork... Genius.
@Valient6 Жыл бұрын
It's not rocket surgery. It's an ok idea but not genius.
@ibob148 Жыл бұрын
Good 😍
@nyLove859 Жыл бұрын
only problem is once the sander gets hot from sanding the glue lets go.
@thisthat7238 Жыл бұрын
даешь термоклей опасным нагревающимся инструментам, претендент на премию дарвина
@user-hv5tx6qv7k Жыл бұрын
В ручную быстрее обработать края трубы
@timoshkovvitaliy Жыл бұрын
вот чем займусь на выходные, только бы в пятницу пробку не потерять
@user-kd2ow7pb1c Жыл бұрын
Great idea
@davidgrossmiller7073 Жыл бұрын
Good wine choice !!
@DonAlfonso63 Жыл бұрын
Хммм... а то что насадка в процессе съезжает в сторону патрона дрели ни кто не заметил!?
@user-ln9pg5vz9b7 ай бұрын
гениально! грандиозно!
@651Alex Жыл бұрын
Ты лучше покажи, как ты шурик ушатает через 15 минут работы такой приспособой!
@user-yd6nn2dr9e Жыл бұрын
в ручную в 10 раз быстрей и качественней.
@dizayiner2552 Жыл бұрын
мамкин инженер в деле)))
@andrei4421 Жыл бұрын
Yes a solution to a problem.
@cfarrell9581 Жыл бұрын
Neat....just what I need for tomorrow ,
@gsxrinfrance5827 Жыл бұрын
Thx...very good tip!!!
@frederikclaessen3184 Жыл бұрын
Если не в курсе Шлифовальные круги и насадки продаются на каждом углу За копейки Зачем огород городить ? Смысл?
@user-ym3le8jh9k Жыл бұрын
Dopo 1 minuto si stacca, usi carta abrasiva carburo di silicio per il ferro ?
@venditeemiltecnica3620 Жыл бұрын
Склейка на термо клей, это вообще не должно держаться
@Fotalist Жыл бұрын
Lmao the pause before the thrust.
@theohmeyegods Жыл бұрын
There's a lot of households in the USA with plenty of wine corks
@ronaldelkins6108 Жыл бұрын
That's awesome
@dickraw7442 Жыл бұрын
Я один ждал момент когда ему в лицо отлетит вся мамбаебина?)))
@kostiamorikov292 Жыл бұрын
You put hot glue on this? The sandpaper will be hot with the friction and disassemble. Sounds good, doesn't work
@lefresh059 Жыл бұрын
хе р-н ч
@user-ig3dh1nu2h Жыл бұрын
Go to harbor freight and spend $3 for sanding drums
@stairman3151 Жыл бұрын
So is there a wine bottle that uses a 3” or 4” cork?
@hdrjunkie Жыл бұрын
I could buy that for a dollar at the hardware store
@kevinmccarthy1076 Жыл бұрын
Know thats a worthwhile tool. 👍
@jhndijkman Жыл бұрын
I would have had that pipe sanded and done in half the time it took to make an attachment for the drill. With - dun dun dunnnn - my hands.
Tried this once. Problem: Friction generates heat, which melts glue, which ends pretty little rolls of sand paper.
What you on about? He didn’t use no glue!
Генитально! Как только вижу термоклей, понимаю, будет ненужная самоделка.
плавкий клей нагрелся и все разлезлось
😅
💯
Супер, правда термоклей отклеивается от тепла
Вообще пофигу, там исполуется бумажная наждачка, она распадется быстрее чем нагреется клей
похоже.чел.давно.в.магаз.не.ступалл
Хрень полная , секунд на 30 работы , дальше клей разогревается и все идет по одному влажному месту .
Всё! Завтра же с утра за вином!
Я тоже ,,
Огурцы и contex не забудьте докупить!!!
термоклей хрень полная нагреется и распадётся
Хорошая самоделка! Вот только есть вопрос: А больше 2 минут она проработает?
U tebia malo probok ot vina???? Ili dorogu do magazina snegom zamelo?
Slick. The tightening of the nut/washer provides compression that holds the sandpaper.
Well done buddy. We hadn't worked that one out.
Исполнение дерьмо. На таком биении ничего не сделаешь.
Идиотовидео
Но это легко устранимо с помощью той же дрели.Потом по размеру склеить бумагу и вперёд))
и термо клей вариант говно.
@@user-jj3fo3ni8z можно взять покрепче, найрит, ПВА- д3, 88-й , суперклей не самый дешёвый , и ок !💪
Отлично! Есть повод сбегать в магазин за бутылочкой вина. Лучше 2 возьму. На вторую пробку наждачку мелкозернистую. 😀
бери сразу ящик.ну шоб сто раз не бегать
@@user-do5ze4ub9k Убедил. Новый годна носу, не пропадет. Да и пробок на год хватит😀 С наступающим.
Fantastic is an idea of a genius!!
you should mount a wing nut, to facilitate the replacement of the abrasive cylinder🤗
And possibly use larger washers on the cork. It might compress better.
Por fin..... Algo funcional.... Felicitaciones.... 👍
Мой кот тоже яйца лижет,когда делать нечего....
Весь в тебя
А у меня, как у человека армейского, собака красит будку
What a innovation he has to be awarded noble prize 🏆
Nobel Prize
А то, что спермоклей от нагрева теряет свои свойства- никто не думает. Доктора в студию!!!
Это заявка для доктора дью. Срочно позовите доктора!
Нафиг надо, надоели эти кринжовые самоделки у него в видео. Лучше пусть что-то более интересное разбирает
Бьёт. Надо было сначала пробку просверлить, зажать болт, в шурик и обточить пробку, а уже потом мотать и клеить наждачку.
Ага, и не а сопли клеить, которые при нагреве поплывут
thank you. The only problem I have is, after I drink that whole bottle of wine, I can't faribikate nuttin.
True but you no longer care.
A great idea.. But unless you have a load of pipes to clean up it's easier by hand. But the idea is great and simple and I'll use it for other sanding jobs that will be more suited to this type of sanding wheel. Well done and thanks for the great video.
Jim let’s be honest, you’ll never use this idea. You’re a nice guy Jim, But you’re not nice enough to use this idea. Jim have a good 2023 my good friend
Молодец какой, я не додумался 😊😊😊
Clever, very clever, my friend! Thanks. ✔
Есть приспособа лепесток, без этих заморочек, и работает супер!
Док, настало твое время!
Опередил 😄
хорошая приспособа,пригодится.👍
Да, только как спермоклей нагреется всему пиз*а
@@andyvillage6857 ,спермоклей использовать не будем,я подумал что можно сделать на липучку.
Dude you are a genius
Не смущает что это будет нагреваться и термо клей не будет держать 😂
Криво просверлил, нужно было зажать сверло, а вращать пробку.
You do know Dremel makes pretty much the same thing, probably works a lot better too
And with the time ,the bottle of wine the nut bolt most likely cheaper too
I bet the sandpaper slips on the cork. It’s also a good idea to drill the hole in the exact center of the cork.
Not THAT long and more costly, though.
Drum sander set of 5 for about 10 bucks!
делитант,Я прав мужики?
Нет. Правильно: дилетант.
на 107%
Finally a homemade tool I might actually use
No, the glue heated up from friction and everything fell apart
lol
Гениально. Никогда бы не додумался.
Очумелые ручки
Если термоклей не отклеится (не допускать нагрева) - вполне удачная идея.
Где же вас, таких гениев находят???
Нобелевскую премию в студию
Lo encontre genial te felicito...
Great idea! I live on winery row (it’s way out of hand here) in central Texas, and have large trashbags full of corks, and no I don’t drink! 😂 I make topwater lures, among other useful things. Going to add this, and some other modifications for buffers etc. to my list. Really appreciate you sharing your ingenuity. Happy New Year! 👍👍👌
By the time you make this you could have had the entire project done!
после таких операций можете попрощаться с подшипниками шпинделя и муфты. шуруповёрт это долго терпеть не станет, он все таки не на это рассчитан.
Ideen muss der Mensch haben👍👍👍👍
Been doing this for 20 years . Should leave a longer tail on sandpaper for longer before it wears out
tightening the nut expands the cork to grip the abrasive tighter. good one
Putting the device in a drill makes the hot glue melt. A roll on emery paper and some elbow grease saves a lot of time
@@turboduckhead6179 Copied from existing drum sander sets.
Well done 👍
Сползла за 2 сек использования збс
Мастерское рукожопство. Нагревающуюся шкурку термоклеем
Есть способ гораздо проще. Делаем на шпильке продольный рез болгаркой. Вставляем наждачку в разрез и наматываем ее на шпильку. ВСЁ. Ну и естественно потом в шурика вставить.
It's cheap enough, I'll just buy it.
Идея хорошая, но термоклей не подойдёт, потому что нождачка нагреется и клей расплавится,
Пробка вращается,а шкурка на месте ,поэтому не забудь клей
Wow.👍
فكرة بسيطة وسهلة وحلوة..
Excellent idea. Far cheaper than buying sanding drums.
These won't last 5 mins buddy.
Есть намного проще решение. На заводе мы называли это - вертолёт)
Wow! Wonderful idea!
Zajefajny pomysł 👍🇵🇱
This is very helpful thanks
Buena la idea pero así se desperdicia mucha lija para utilizar el otro extremo nececita romper la lija para quitar el pegamento
Стык нужно делать по диагонали и лучше без нахлеста, и не на термоклей
Thank you for reminding me I have to call Spectrum cable
Excelent
Пробка в тисках - это сильно! С руки сверлить - тоже... про центровку и биение промолчим. Сопли термические... ой.
A 1965 hack !! Awesome dude!
i like it
Quicker and Cheaper to buy than to make.
Здорова! Глупый момент. Трубочка с разрезом и лентой наждачки проще и лучше.
хрень, нагреется и отклеится!
Трубу проще лентой обвернуть и ручками
Awesome an actual tool thats useful . Maybe the first video like this that's actually worth the watch
Or you go buy one for $3 a save time and supplies that are worth more 😂
@@henryhenry3832 You'd be the type to save a cork ,a piece of all thread and 2 washers and nuts huh. A dollar saved is a dollar earned.
@@henryhenry3832 or you don't know how big of a wast of money buying crap like this is when you have 200ft roll of sandpaper laying around
@@Aprilfool4121 only if you’re time is worth nothing, mine is worth $115 per hour, so I would rather buy a $3 flapper wheel and save my customers a lot of money
@@henryhenry3832 you do you dude.
Сначала купить бутыль вина чтобы появилась пробка. А далее... дануНах эту самоделку, надо идти за следующей.....
Soon as he started using hot glue I knew, engineer. But then when he started drilling a cork... Genius.
It's not rocket surgery. It's an ok idea but not genius.
Good 😍
only problem is once the sander gets hot from sanding the glue lets go.
даешь термоклей опасным нагревающимся инструментам, претендент на премию дарвина
В ручную быстрее обработать края трубы
вот чем займусь на выходные, только бы в пятницу пробку не потерять
Great idea
Good wine choice !!
Хммм... а то что насадка в процессе съезжает в сторону патрона дрели ни кто не заметил!?
гениально! грандиозно!
Ты лучше покажи, как ты шурик ушатает через 15 минут работы такой приспособой!
в ручную в 10 раз быстрей и качественней.
мамкин инженер в деле)))
Yes a solution to a problem.
Neat....just what I need for tomorrow ,
Thx...very good tip!!!
Если не в курсе Шлифовальные круги и насадки продаются на каждом углу За копейки Зачем огород городить ? Смысл?
Dopo 1 minuto si stacca, usi carta abrasiva carburo di silicio per il ferro ?
Склейка на термо клей, это вообще не должно держаться
Lmao the pause before the thrust.
There's a lot of households in the USA with plenty of wine corks
That's awesome
Я один ждал момент когда ему в лицо отлетит вся мамбаебина?)))
You put hot glue on this? The sandpaper will be hot with the friction and disassemble. Sounds good, doesn't work
хе р-н ч
Go to harbor freight and spend $3 for sanding drums
So is there a wine bottle that uses a 3” or 4” cork?
I could buy that for a dollar at the hardware store
Know thats a worthwhile tool. 👍
I would have had that pipe sanded and done in half the time it took to make an attachment for the drill. With - dun dun dunnnn - my hands.