How To Make Drone With Hand-made Radio Control. DIY Drone
How to make quadcopter with arduino radio controller.
1806 Brushles Motors : s.click.aliexpress.com/e/_DEL...
Emax 12A Brushless ESC : s.click.aliexpress.com/e/_DBP...
PCB Boards: s.click.aliexpress.com/e/_DEq...
Standoff Spacer : s.click.aliexpress.com/e/_DEY...
4045 Propeller: s.click.aliexpress.com/e/_DEI...
3S Lipo (800-1300mah) : s.click.aliexpress.com/e/_DCA...
2mm gold Connectors: s.click.aliexpress.com/e/_DE7...
T-Plug Connector & Cable (Male) : s.click.aliexpress.com/e/_Dl9...
2 Pin JST & Cable : s.click.aliexpress.com/e/_DmR...
KK2.1.5 Flight Controller Board : s.click.aliexpress.com/e/_Dcj... OR s.click.aliexpress.com/e/_Dkg...
M3 Screw: s.click.aliexpress.com/e/_DmW...
M3 Nuts: s.click.aliexpress.com/e/_DBW...
Cable Stripper : s.click.aliexpress.com/e/_DD5...
Lipo Battery Charger: s.click.aliexpress.com/e/_DF5... OR
s.click.aliexpress.com/e/_Dlw...
How to make 6 CH Remote Control video : • DIY 6 Channels Radio C...
Thanks for watching. If you want to support, join this channel.
/ @kendin-yap
Connection Schemes: www.rcpano.net/2020/06/18/how...
#drone #quadcopter
00:00 Video introduction
00:09 Making
11:18 KK2.15 Board setup
13:15 Radio control test
14:34 Flight
All of my videos: bit.ly/2Z9QVYK
Thanks For Watching And Please don't Forget To Like, Share & Subscribe For More Awesome Videos.
KendinYap Channel kzhead.info/tools/gjJ.html...
Que trabajo tan elaborado. Un Dron casero y quedó genial. Espero que cada ves sea más fácil de hacer. Saludos desde Cali, Colombia.
Harika bir kanal keşfetmenin zevkini yaşattınız teşekkür ederim. Sesinize yer vermemişsiniz ama keşke sesli anlatımınızdan da mahrum kalmasaymışız. Emeğinize sağlık.
Hocam geçen bu video sayesinde dronumu tamamladım.Mühendislik tasarım ödevimdi ve hocam çok beğendi.Kendimi mühendis gibi hissettiğim bir projeydi.Çok teşekkür ederim size çok şey kattınız.Var olun...
Your WhatsApp???
lisede misisniz
Hangi alıcıyı tercih ettiniz ben videodakinden bulamadım
Koray abi 16 yaşımdayım robot yapımı hakkında hiçbir bilgim yok kendi basit fikirlerimi hayata geçirebilecek kadar öğrenmek istiyorum nasıl başlamam gerektiğini anlatabilir misin
@@Peynir12Kardeşim seninle aynı durumdayım bende
Parabéns, excelente . Eu vejo empresas fabricando drones que não tem 1% da qualidade de voo do seu drone perfeito. muito inteligente
Iwpp2900😅😮❤
hocam yıllardır bu işleri takip ediyorum ilk defa delikli plaketten frame yapan görüyorum gerçekten çok etkili , pratik ve ekonomik bir çözüm ellerinize sağlık
Salut je m'appelle
Always wanted to make my own drone, glad I found your video bud! Very well explained, although now that I realize I don't think you said a single word the entire video 😆 either way instant fan of your work and now Subscriber to your channel, Sir. Keep up the awesome work!
You are showing the fun about building from "scratch", instead of ordering something already made or so. Nice 🙂
It’s more fun and it makes you feel like a nerd (in a good way)
Hocam kanalınızla bugün tanıştım. Bir mühendislik öğrencisi olarak takdir ediyorum emeklerinizi. Elinize sağlık, dilerim çok daha iyi yerlere ulaşırsınız.
ne mühendisliği okuyorsun abi
@@alperengul2578 sağane
starting now
Translated Message is Sir, I met your channel today. As an engineering student, I appreciate your efforts. Good luck, I hope you reach much better places
@@alperengul2578 bahçe mühendisi
Hoca ,eline koluna sağlık ,,bizleri çook bilgi sahibi ediyorsunuz ,tesekur ederim
Çok etkili, pratik ve ekonomik bir tasarım ellerinize sağlık.
Świetna robota, jestem pod wrażeniem tej budowy drona. 🤯
Yine muhteşem bir video. Teşekkürler hocam.
Very well done. Using basic components you constructed a great flying drone. I must add that the pilot makes it look easy.
I'm Claudio Sallum from BRAZIL AND I'M ALSO an instant fan of your work and now a subscriber to your channel, sir. Keep up the amazing work!
Türkiyede böyle bir kanal olması heyecan verici.
İçerik ve donanım alt yapısı olarak çok başarılı bir kanal tebrik ederim.Basarilar dilerim devam ederseniz daha iyi yerlere geleceğimize eminim.Yerli bir kanal olmanız dolayısıyla ayrıca gurur duyuyorum.
This is a brilliant video. Makes it very clear how to go about building one.
Parabéns pelo vídeo 👏🏻, aprendo muito com você
hi daniel carlos this video is in english,but you speak in portuguese
That is amazing! The only issue I can even see is accessing the screws to replace a broken arm. Nice drone!
If you have some video editing ambitions then I may have an idea for something you could try. At 0:50 you have the measurements for the board, but you rotate the board while the measurements stay in place. It would be cool if the measurements would follow the board and rotate along with it. This could be done tediously by keyframing every frame individually, but some video editing programs also have tracking features which allow you to make it follow the pcb's position and rotation automagically. I think it would look cool if it were like that, but it's absolutely fine the way it is. So if you don't feel like doing something like that then that's totally fine :D
@kendinYap I love your videos, these are simple but very explanatory. Could you please make a drone or plane which streams live video stream to a mobile app using data cable as commercial drones do. They use the same remote control and a data cable to attach with a mobile phone to record live video. I watched an FPV video on your channel too but it was streaming the video to another receiving screen but not to the mobile app. Thank you in advance for your guidance and help.
I'm from Brazil, congratulations and thank you!
Well done, always ready to learn more from you, great job with yield understanding
This is really cool. Now I want to build one too. Your video is very detailed. I would have loved to hear you explain the steps in a voiceover, but this will definitely help. Thank you!
He is Turkish. If that guy had done the voice-over in the video, it would have been in Turkish. Maybe that's why you don't understand conversations.
@@oylesinebirhesap211 why the rude response?
this guy deserve a medal :D Thx for tutorial
This is a great video and thank you teacher
As an odiance bro i loved your design and tutorial of making aeroplanes with its circuit connection
it actually fly pretty decently.. great job !!!!
Bu tür videoları bir türkün de çekmesi bizi çok mutlu ediyor.
Aynen
thanks master yoda.. greeting with big honours from indonesia.. 🙏
Tenyata ada yg dari indonesia
Aku juga dari Indonesia
all we are muslim brothers
I can't believe what I have just watched, That was awesome. Well Done 👍 Good Job 👊💯
🖒🖒🖒🖒🖒
Mannn that is awesome and im following your video to make my own. Ill really appreciate if you could add an oled display to the transmitter really liked it maann
Did you make it by now?
Wow! That's so stable
Everywhere I go, I see his face.
Abi mükkemmel çalışmalarının devamını dilerim dolar uçmuş ben kumanda bile alamiyrum
hola muy buen video espero que permanezcan haciendo este metarial... Voy a seguir mirando sus creaciones. Les mando un beso nos vemos luego ❤️👍🏽
je teme
ძალიან სასარგებლოა ჩემთვის, მადლობა
This controller board has more settings than iphone.
😂😂😂
😂😂😂
😂😂😂😂
That's really
Do you know what an iphone is
Very clever and good luck on anything you build next. The Hoppers, down under. (Australia)
Süper olmuş, eline sağlık hocam.
wow this drone sounds like a Tie Fighter!!
Güzel çalışma, beni abonen yaptı.
really loved it and learnt a lot. One doubt though, whether the transmitter and receiver is the same one that you made earlier in different video(the 6 channel transmitter)? And another question, will you make a arduino based flight controller for the same? thank you for the videos and love from India.
The basic principles are the same for both. But there are some differences.
@@Kendin-Yap Can you please elaborate what are those differences? The receiver in this case also doesn't use PPM ouput. I think earlier ( 6 channel receiver in your video) and in present case, both are receivers with PWM output.
Elinize sağlık 👍 mükemmel
Emeklerine sağlık...
Impressive build, educational and entertaining!
vay maşallah bugün başlarsam yaz sonuna kadar ancak bitiririm ben. Kappa :D :ADS
Bitirdin mi kardeşim merak ettim 😂😂
@@talhaserin6109 yapamadım :S
@@geberrrrrrrrrrrrrrrrrrrrrr sağlık olsun 😂😂
Çook iyi fikir helal olsun 😀👍
Abi böyle şeyler görmek çok güzel 👏👏👏
Daha iyi bir uçuş kontrol sistemi ile freestyle drone videosu bekliyoruz
eyes: I got it, I can make. hand: no,you cant!
Congratulations! Good job 👍🏻
Harika, elinize sağlık
Reis harikasın bee
Hocam esc gibi bazı elemanlar çok pahalı. eski sayılmayan bir drone inceledim, kücük tek devre ile kızılötesi yardımıyla motorlara bağlanıp kumanda ile kontrol ediyordu. bunun için detaylı bir video çekebilirmisiniz? wifi modülü ile olabilir, nrf24l01 ile olabilir, sp8622 ile olabilir. saygılar
hello new friend thank you for share have a wonderful day
Thank you for your generosity in sharing your expertise! From Barcelona.
I APPRECIATE YOUR TALENT SIR,RESPECT SIR,I'LL MAKE DRONE BY UR VIDEOS
Merci beaucoup mon frère adoré tes vidéos 💔😘😉😉😉😉😜😜
Cutting and drilling FR4 (pcb board) is dangrous for your health because it produces glass powder (FR4 is fiber glass). If you inhale that, your system cannot get rid of it so it accumulates (similar to asbestos) . In general cutting and drilling FR4 is a "big no no" in elecronic assembly labs(use a PCB gillotine for cutting it). When it cannot be avoided, it is recomended to be done eithe in water, or with wet boards (so that the powder doesn't fly off).
Thanks for reminding
Thanks
the pcb he is drilling in the video is paper phenolic no glass epoxy
You truly deserve a medal Sir. Fantastic work. 👌
Cool tutorial thanks bro!
Please permission, I am sharing this video for learning. Thank you
Damn. I heard they're looking for a new CEO at DJI
I really love your videos, am willing to make one too.. but could you make a video adding a camera to this drone, so that the photage can be seen on a PC or smartphone like real drones do please?? 🙏🙏
Very well done indeed!!!
Maşallah harika olmuş abone oldum .
Abi 3D yazıcın varsa kendin bir özel tasarım yapıp rc uçak yapabilir misin
Aynısını dicektim
Aynen 3d yazici boyle maketlerde cok is gorur
Rc yapmak öyle kolay değil mesela f22 raptorun rc sini yapacak onun için mini turbo jet motoruna ihtiyacın var anladığım kadarıyla reis elektronikden anlıyor motordan pek anlamıyor
很厉害啊!!!!
Merhabalar, Receiver'ın olduğu plaketin bağlantılarını detaylı anlatabilir misiniz?? Teşekkürer ederim, çok güzel olmuş. İyi çalışmalar
Hocam merhaba, videolarınız çok kaliteli yürekten tebrik ediyorum. Ben internette bu eski oyun kolları (joystick FT Aviator gibi) ile drone kontrolü yapmak ile ilgili araştırmalar yapıyorum ancak bulamadım. Bir örnek çalışma yaparsanız harika olurdu. Başarılar dilerim 👏👏👏
Eski oyun kolları ile olur mu bilmem ama Unity oyun motoruna biraz hakimseniz, Arduino ve Unity arasında Serial Port üzerinden entegrasyon yaparak modern oyun kolları ile kontrol sağlayabilirsiniz. Ben de taze bir yazılım mühendisi olarak tamamen el yapımı bir drone yapma işine merak saldım. Yazılımını yazmayı gözüm kesiyor da işin donanım kısmı, uçuş fiziği vesaire falan hala soru işareti. İyi çalışmalar dilerim.
@@mehmetbatuhanarslanturk1661 usta uçuş kontrol kartının frameworkleri filen internette var mı ? kendi kendine rota belirleyip bu rotayı gidebilecek bir drone yapmayı deniyorum da nereden başlıyim ?
Nice. I'm trying to make mine too.
All the best
Great work and effort behind the project ....
Bu kanalı 300 abonesi oldugu zamanlardan beri takip ediyorum bu kadar buyuyeceği kalitesinden belliydi zaten yine mukemmel bir iş çikarmişsin hocam kolay gelsin
Thanks for amazing tutorial!
No GPS? Why the setting is loaded with lots of info than huawei 😂
Hello. Thank you for the video. What is the flight time before the drone dies?
I am a big fan of your channel
Good morning boys
huh where do i find these pro materialsssss 🤣
The drone is SUPER cool
FASCINATING !!!
It's a bit difficult especially the body lol
Very difficult
Can you explain to us the way to make a drone with Arduino Uno and the code?
The code is easy you can code it yourself
@@yassineseghrouchni8175 hi can you help me ?
Gostei!!! Parabens!!
well-done, great, fantastic, superb, amazing and fabulous work, you should modify it and make it more commercial and really you are great and smart engineer, Elina saglik, Saygilart, Irak, Kerkuk
very very very very god
Dang, still using a KK board....
멋지네요~ really gorgeous drone!!!
Just simply amazing!
Kendin yap, Teach me how to make a remote control submarine, only you can do it , no one else can do it , I hope you will make it beautiful with diagram like you other videos THANKS 🎥🎥🎥🎥🎥👌👌👌👌👌
Hi
Great Drone
Seni tebrik ederim çok faydalı video.demeki bizim insanımızda böyle şeyler yapabiliyor.senin videoların örnek olsun bir çok faydasız ve boş işler yapan sosyal medya daki avanaklara
Can you build cheaper than this cause i can't afford this pls Then give me a link
Range 130-150 metre, flying duration ~5-6 minutes with 800mAh, up to 1300mah can be used. Found it from the answers in comment section
Tebrikler eline emegine saglik👍
AMAZINGGGGGGGGGGGGGGGGG!!!!!!!!!!!!!!!!!!!!!!!!!!! LOVE THIS VIDEO!!!
You can order this from jlcpcb .
reis bunun malzemelerı zaten bir dron fiyatı eder elıne koluna sağlık türkiyede teksin seviliyosun
Kanka amaç dronu ucuza getirmek değil.d
Eline sağlık usta çok iyi olmuş
cool dude love the saw how did you make that ? id like to build one :oD