Only $2 for 5 pcs PCBs and Free SMT Assembly at JLCPCB& Get $30 for
New Users: www.jlcpcb.com/cyt
Get Altium free trial -www.altium.com/yt/tapendra-ma...
In this video I am showing the easiest way to build a high power induction heater.
Required Material-
1. MOSFET IRFP260N
2. Inductor 200uH
3. Fast Diode FR307
4. 12v Zener Diode
5. High voltage capacitor 0.33uF
6. Resistor 470ohm
7. Prototyping Board
8. 6mm Copper Tube
Follow me on
Insta- / tapendramandal
Facebook- / tapendramandal
Thanks for watching my video.
#HomeMade #InductionHeater #DIY
In fact, it is one of the most beautiful waters I have seen on KZhead in terms of clarity, creativity, and the best videos. Rather, it excels many videos in explaining its structure, as well as bringing it closer with clarity and facilitating the work. It made me look at it simply. Rounding and clarifying with his name and illuminating the resistors and diodes is the best thing you have done. Filming on the close with clarity and with writing for each resistance. Thank you for that, but I would have made you a genius and mighty if I had made the circuit without the chip. The bells every day and always click on the likes, and I will give you a million stars and likes, but we thank you for that
YEAH TAPENDRA!! SO HAPPY TO SEE YOU ON THE PLATFORM AGAIN!
Very powerful induction heating M/C 🔥 🔥 🔥
tapendra bhai....mind blowing keep it up bro...
glad to see you uploading again :)
Very good bro
Professional ❤
nice welcome back bro
Bro its an amazing project 🤴
Great job brother
Круто. Привет из Минска
Tenks bro
Tanks for sharing Please tell me how many turn on inducter and which diameter?🌹
Welcome back
Great gg
Welcome back brother. After a long time. I have try contacting you so many times Happy to see u back
Thank chintan Bro
yaaayyyyy you're backkkkk
Nice
Long time no see!!
You Back again with an Amazing Project
Thanks
@@tapendramandal Welcome 😄
Welcome back brother and please check that code links of self balancing Robot.. not working!!
Op 🔥🔥
Welcome back sir
Thank you 🙏
👌👌👌
Tapendra ka b tech merey sath complete hoa tha 🤣🤣
খুব ভালো বেয়াই
Thanks bei
sir please make a video on how to make esc for bldc motor
Bro I am not geting view can I upload your old video please replay
I want to buy it
how high goes temperature ?
I like it
Thank you
👍👍👍😊
❤❤❤
Op
Is this not 360 W. Can this circuit handle 1000W? How much maximum it can handle current in video there is given about voltage 12-48 v but not current.
Bhat din bad
please make a project - "home theater turn on in the morning automatically like an alarm"
berapa harga pcb nya
Hi, what power supply did you used? thx
He used the power supply that he showed in the video. He even showed the label and ratings, so you wouldn't need to ask.
@@johncoops6897Hello anhz Should I use 470 2w or 1w resistor, thanks
Why bro long time no video
where can i learn how to build this?
You can learn it right here, simply by watching the video. Go figure 😂
@@johncoops6897 no, i want to learn how to come up with the electronic circuit and not how to build it.
@@multiarray2320 - Then you will need to learn electronics. The easiest way is to take a university course, or alternatively you can learn by "doing". For example, build existing circuits that interest you, and then modify them and see what happens.
Hello Sir, I watch your every videos but I have some serious issues please read the whole paragraph then only you will get that what I exactly want to say. I wants to know which microcontrollers are used nowadays for Industrial and Domestic Automation (except PLC), such as microntrollers which are being used in Havells Smart Fan or Anchor IR remote Control Fan, or SYSKA Smart LED, etc all. All I wanted to know that these small smd based Smart Home Automation items by big brands uses which Microntroller for their smart products such as Fan, Bulb, Motor, Door Locks, etc. ??? Because as far as I have experienced AVR ATMega328P, PIC are not suitable for operating Inductive Loads (such as Fan or Solenoid Valve, Water Pumps , etc) as I have seen they produces back emf while on operation and the whole operation gets freezes down as a back emf creates disturbance for the microcontrollers and hence this way the whole code gets corrupted. I am seriously messed up with all these issues and till now I haven't found any relatable solution to this problem on the internet. I hope you have the answer to my question. I request you to please make a seperate video for me explaining all these Industrial Automation and Limitations of AVR, ATMega 328P, PIC, etc with troubleshooting of all these problems(especially on how to operate heavy Inductive loads on Arduino and how to troubleshoot back emf generated by motors). I have faced back emf issue on DC motors and Johnson Motors too, they were also not properly driven by Arduino and after 2nd or 3rd try they have also shown abnormal operation. I don't know why Arduino can't handle heavy current consuming DC motors with Motor Drivers or even AC motors on Relay. I faced the same issue on both !!! The whole circuit gets freezes down after 2nd or 3rd try and at last I get left with only 2 options, either re-upload the code or Restart the Arduino. Eagerly waiting for you response. Now you are the only last hope for me to get this sorted out. Please help me !!! 🙏🙏🙏
Nobody can answer your questions. If you have problems with Back EMF then you need to deal with the Back EMF. A microcontroller is just a controller it cannot drive large loads, so whatever you are doing between the micro and the motor is wrong. As I said... deal with the Back EMF, if that is what is causing your problems.
Could you identify each of the components?
You mean like on the schematic circuit diagram that he showed on-screen throughout the video?
Hello bro may pakhanjore se hu aaj hi pata chala tumhare bare me nice 🙂 👍👍👍 bro may vlog banata hu may tumhare video dekrahu help me now bro... sanjay shil Vlog
He will be coming back next year again.
Next week U will get a new video 😀
@@tapendramandal Can i melt copper with it??
It can not be 1kW, if input power supply is 24V@15A :(
Still u remember your youtube password
😂
Bhai apna no. Do
😂😂😂😂
So long bro .....
Yeah bro
Not 1kw.
Fake
মরিচ বাতি | পানির বোতল দিয়ে লাইট | Decoration Wall Light | Wall decoration ideas | Diy Wall Decor kzhead.info/sun/l85qc9yyhV-LhHA/bejne.html
In fact, it is one of the most beautiful waters I have seen on KZhead in terms of clarity, creativity, and the best videos. Rather, it excels many videos in explaining its structure, as well as bringing it closer with clarity and facilitating the work. It made me look at it simply. Rounding and clarifying with his name and illuminating the resistors and diodes is the best thing you have done. Filming on the close with clarity and with writing for each resistance. Thank you for that, but I would have made you a genius and mighty if I had made the circuit without the chip. The bells every day and always click on the likes, and I will give you a million stars and likes, but we thank you for that