I sharpen drills in 30 seconds. Tool for sharpening drills. idea #2
2024 ж. 12 Ақп.
872 303 Рет қаралды
I made a sharpening tool that makes the drill bit sharper than a new drill bit.
This tool will be distributed free of charge to those who purchase the Sander Stand Plan.
#how to sharpen a dril #drill bit sharpener #how to make
Нельзя так затачивать. Такие диски не предназначены для боковой нагрузки, поскольку сетку защитную стачиваете, а ещё они гнутся при надавливании, что на видео и видно. Полноценный заточной диск, но убавить до нужной скорости вращения обороты у УШМ, чтобы не превысить допустимую угловую скорость вращения камня. Работать с торца диска, а не сбоку. Или алмазную чашку, что попрочнее будет.В общем задумка неплоха, но требует доработки. Заднюю кромку сверла нужно сгладить, а затачивается режущая часть.
И что, под каждый диаметр свёрл делать эту приспособу? 😂😂😂
Мой дедушка говаривал, - "а где ручка?" Зачем? А что-бы закинуть подальше удобно было!..
2 одинаковых уголка не будут так ходить ( в притирку) надо скачивать грань у верхнего, или будет зазор и верхний будет гулять.
A lot of negative comments from people who claim to know better. I was pleased you refrained from the lunatic practice of removing the disc guard from your angle grinder.
А как насчет заднего угла режущей кромки.
The included Angle for a twist drill is 118/122°
Isso aí parceiro, show de bola Att: Weliton Marks - Canal Desbravatube
This drill bit does not have any back relief The cutting edge is shorter than then the tail It would be next to useless.
thank you, you are the best
Полное враньё. За одну установку сверло заточить невозможно. Необходима обеспечить затылование задней поверхности.
I can sharpen a drill in 30 seconds doing it by hand . 40 years as a toolmaker.
With the cutter wheel? I do.
Thank you very much
Под каждый диаметр своя приспособа?
Success! For only 3x the cost of a new drill bit and 10x the duration it would take to go buy one; you too could have fresh, sharp, and slightly shorter drill bits! 😂
Do you throw away a chisel when it gets blunt? Yeah a jig takes time and money to build but once it's done you've got it. Could have had it half made in the time it took to make your ridiculous comment.
@@robinmarwick1982 man sharpening a chisel is one thing, this is something totally different
@@drolinginkno...they're both tools that make holes in things. Got my first set of drills 20 odd years ago; true enough they're shorter than they were but so are my chisels. Monumental waste throwing away a drill when it can be sharpened.
У меня ученики без опыта , на глаз на алмазе и то лучше затачивают
Cutting disk's are not designed for use in grinding. They can disintegrate. Too dangerous for me.
Да бред какой то видно, что люфты на уголках большие
Пробую, каким диском пользуетесь,
This way it don't drill neither butter! The attack angle is wrong and it's overheating!
Dangerous use of slitting disc!!!
Drill a bit in 30 seconds but takes you 4 hours to build the tool!
😊😊😊😊😊😊😊😊😊😊😊
😊😊😊😊😊😊😊😊😊😊😊
c'est mieux que rien, mais pour tout outil de coupe, en plus du tranchant il faut un angle de dépouille ce que ne fait pas votre système.
good tips for life
LOS TALADROS NO SE AFILAN,LAS BROCAS SI.
Time and materials way more than buying some more bits😂
So you need to build a jig for each size drill????? This is so damned stupid. Just go sit and buy a bid sharpener for 20 dollars.
I sharpen them in 3 seconds without a silly tool
👍👍👍
NO slipp angell thats why its overheating
Bonjour, lorsque l'on ne sait pas affûter un foret à la main, on s'adresse à quelqu'un qui s'y connait.
Гайки тільки заважають, все одно, на око.
о ко ко))
Купи новую и всё,...
That’s a long 30 seconds 🙄🙄
Я точу свёрла секунд за 20. А если у тебя руки из жопы ,то можешь ещё пять приспособ сделать ,не поможет .Ты крутишь сверло на котором видно обратный угол заточки.
Pre magorov 😂
D= 4,5.6.8 10????
That's not 30 sec
Viel zu unpraktisch,schleife ich von Hand besser und schneller 😛
Dont look sharp when driling
Totally wrong if that drill was sharpened correctly then you drill something the steel spirals shavings should came out both sides of the drill when drilling . Never use a cutting disk and grinding on the side of it . Use a grinding disk .. clearances of the drill aint right and thats why you force the drill in to the metal . Never hold the job by hand and then drill it . Use a vice or clamp it down . No engineering knowledge
That's what I like about KZhead always some keyboard warrior to pour negativity on someone else's work. Granted safety issues holding a work piece by hand while drilling it. The fact the guy produced a pretty reasonable jig somewhat contradicts your remark of 'no engineering knowledge'
Why doesn't the cutting disk say you not sposed to grind with it?
Видимо никогда у криворуких не кончатся видео о заточке сверл с придумыванием разной хрени. Вы на свои руки посмотрите,откуда они растут. Я ЗАТАЧИВАЮ СВЕРЛА ДЕРЖА В РУКАХ ОПИРАЯСЬ НА ПОДЛОКОТНИК НАЖДАЧНОГО СТАНКА С КРУГОМ МЕЛКОЙ ЗЕРНИСТОСТИ.
Emesh gency only.... 😊
А проворот свердла, убрать пятку?
Mouay... Bof 🙄 Il y a plus simple et plus efficace
Po co ta głupia muzyka
Очередной ОНАНИЗМ...
Encore des conneries pour avoir de l’argent 👎👎
w buty wsadz sobie to ostrzenie wierteł.
How can I delete this crap
Non avevi un audio che non rompesse le palle?
😂