Triple-Piston Pneumatic Circular Saw [Restoration]

2022 ж. 8 Қар.
601 180 Рет қаралды

This restoration is on a 1920s Model B12 "Safety Saw" pneumatic circular saw made by the Ingersoll-Rand Co.. The "Safety Saw" name was in reference to the patented design of the retractable blade guard, one of the first of its kind. This saw runs off of a triple-piston "Little David" motor that Ingersoll-Rand seemed to use in a number of their larger pneumatic tools.
Unfortunately, I could not find any mention of this saw in the literature and therefore it is only an educated guess on how much compressed air this saw need to run.
The saw had many previous repairs that all needed some new attention. The main issue with this item was the completely seized throttle valve and the extra crusty and old grease that had hardened over time.
Once cleaned of grease, repaired, and reassembled the saw would idle when I applied a bit of compressed air from my air compressor which can only put out 90 psi @ 20cfm. The idling is either due to the low flow of air not providing enough force on some valve to completely seal it, or there is a leak somewhere within the saw. Either way, I decided not to fix that issue because an idling pneumatic circular saw sounds AMAZING and I could listen to it all day.
Despite the reduced air flow, the saw still cut just fine and definitely had tons of torque. I'll be sure to use this next time I need to cut a thick wood beam with the most ironically named tool I've restored.
Wrenches, screwdrivers, and socket drivers are now for sale at www.handtoolrescue.com
Help secure more tools for future videos (if you want):
/ handtoolrescue
Instagram:
/ handtoolrescue
Facebook Group - Share your restorations
/ handtoolrescue
/ handtoolrescue
Reddit - Share your restorations
/ handtoolrescue
Podcast (with @jimmydiresta and Andrew Alexander) - anchor.fm/fitzall

Пікірлер
  • I launched a new perfect handle smaller screwdriver for sale on the website. Some might even say it's an actual usable size this time....www.handtoolrescue.com

    @HandToolRescue@HandToolRescue Жыл бұрын
    • Useful size? What is this heresy?

      @horstyoutube6413@horstyoutube6413 Жыл бұрын
    • Давление побольше надо !

      @user-yh6dr9jn4x@user-yh6dr9jn4x Жыл бұрын
    • I purchased one as a present for my son. It's freaking awesome!!

      @patrickmchose7472@patrickmchose7472 Жыл бұрын
    • I do so very much enjoy your restoration videos. Thank you for posting

      @micrashed@micrashed Жыл бұрын
    • Bro, for how long have you had that Evaporust barrel? THat water look almost black like oil.

      @diegoviniciomejiaquesada4754@diegoviniciomejiaquesada4754 Жыл бұрын
  • Easily one of my top five favorite triple-piston pneumatic circular saw restoration videos!

    @ColombianComplain@ColombianComplain Жыл бұрын
    • to ruin the joke HOW MANY TRIPLE PISTON PNEUMATIC CIRCULAR SAW RESTORATION VIDEOS ARE THERE??!

      @dimitar4y@dimitar4y Жыл бұрын
    • @@dimitar4y at least one?

      @frogz@frogz Жыл бұрын
    • @@frogz 😂😂

      @jodidavis6595@jodidavis6595 Жыл бұрын
    • Never thought it even existed

      @canonsonico3752@canonsonico3752 Жыл бұрын
    • Naa !!! You need to be more specific. This is the B12 model which has been done to death. I've seen at least five better ones !!

      @Chewligan1@Chewligan1 Жыл бұрын
  • These heavy duty pneumatic tools probably saw a lot of use in the mining industry. Many mines were not electrified, and usage of pneumatic tools would also reduce risk of sparks unlike electric motors. Also these pneumatic motors were light and compact for their power at the time. Drills and hammers were already using pneumatic air, so the piping and large compressors were there, and I think saws like this would come handy when timbering the mine. The standing pneumatic grinder you mentioned, lot of the larger mines had workshops down the levels, so running those workshop tools from the air line makes perfect sense too. Very interesting restoration as always!

    @ketturi@ketturi Жыл бұрын
    • There was probably more than a couple of job sites out in the bush that might have had a petrol powered compressor on site but no electricity hooked up yet this would have suited. Thinking with the right diamond wheel, enough water and no sense of self preservation it'd be bloody good for cutting marble

      @krissteel4074@krissteel4074 Жыл бұрын
    • Oh! Good point! I wonder if the lack of sparks from a brushed electric motor is why it's a "Safety" saw.

      @wbfaulk@wbfaulk Жыл бұрын
    • @@wbfaulk No, safety because the guard is spring biased so that it dropping will not cut you, you need deliberate force to expose the blade from the guard. Yes mines have a lot of pneumatic tools down shaft, all for safety, and no sparking, though a lot of them also have hydraulic tooling there as well, powered by water, as after all you do not need a compressor for them, merely the main shaft depth and that column of water. Dump the water to both cool the rock and keep dust down, and in any case you need to pump large volumes of dirty water out, so you have the sumps and pumps there, and as well that water often contains useful amounts of ore, so it also gets run through a centrifuge to get rock out, which then is treated like ore, and the rest is filtered and treated before discharge, though a lot also goes back down after that as clean process water.

      @SeanBZA@SeanBZA Жыл бұрын
    • Agreed. It's primary use is in mining. Compressed air was used not just for drilling but also underground winches - this saw would run on the same source of air.

      @jackking5567@jackking5567 Жыл бұрын
    • i was told that air tools are also often used when you expect super long run times on the tools. they don't heat up or wear out like motor driven tools do, and they can often get a lot more torque. i have an air ratchet set meant for a racing pit crew, and they are torque monsters despite not being even rated for torqueing bolts

      @Gunbudder@Gunbudder Жыл бұрын
  • Awesome! I remember seeing the Craigslist ad and thinking "HandTool Rescue needs this death machine, I mean this "Safety Saw", in his life." Great restoration, especially great job on that aluminum repair! And thanks for sharing the unique engineering of this dastardly thing with us, I love the triple piston arrangement, and the brilliant way they kept the size small by "overlapping" all of the connecting rods! I also just LOVE the personality that thing has, the way it idles. Brilliant :)

    @LizMatzelle@LizMatzelle Жыл бұрын
    • Thank you again for sending this my way! Couldn't have done it without you.

      @HandToolRescue@HandToolRescue Жыл бұрын
    • @@HandToolRescue literally!

      @xenoxaos1@xenoxaos1 Жыл бұрын
    • Awesome. :)

      @IstasPumaNevada@IstasPumaNevada Жыл бұрын
    • Wow. That’s a generous gift, to all of us. Cheers.

      @johnsrabe@johnsrabe Жыл бұрын
    • Liz, I think I can say this without any worry of not speaking for any of the viewers of this channel, thank you, you let us see a piece of history!

      @frogz@frogz Жыл бұрын
  • I think it is "idling" because the removed corrosion in the trigger valve assembly has resulted in too much clearance and thus the valve is slightly leaking. I imagine if you plated the spool valve with electrolysis it might take up the lost clearance.

    @larrycleeton@larrycleeton Жыл бұрын
    • I think the idling sounds kind of cool. It would give you rhythm like a metronome if it was used in the field on repetitive cuts. Chugga chugga.

      @paedahe4975@paedahe4975 Жыл бұрын
    • @@paedahe4975 That's the pleasing beat of the extra safety overflowing. Those old tools had too much safety for their own good, that's all.

      @R.Daneel@R.Daneel Жыл бұрын
    • I wonder if there were o-rings on the control valve at one point

      @ericpaul4575@ericpaul4575 Жыл бұрын
    • @@ericpaul4575 Prob too old for O-rings, if you notice, it's all Regular slotted screws, too old for Allens and Phillips too - My 1946 and earlier stull is all slots screws, no "Modern Headed" fasteners?

      @Mad-Duk_Machine_Werkes@Mad-Duk_Machine_Werkes Жыл бұрын
    • It's supposed to do that... I Walter Mitty designed it!

      @DiverCTH@DiverCTH Жыл бұрын
  • Tools made before the days of workplace safety are always so freaking cool!

    @user-js4vh2lw6n@user-js4vh2lw6n Жыл бұрын
    • Yeah, but once they taste blood, they want more!

      @pfadiva@pfadiva Жыл бұрын
  • At first I was a bit sceptical about this saw. But then it started idling, and the sound it makes when it's cutting, it's freaking AWESOME!

    @klauswunderlich6169@klauswunderlich6169 Жыл бұрын
  • I've never noticed how much closed captions enhances watching these videos until just now.

    @kevinbissinger@kevinbissinger Жыл бұрын
  • This HAS to be the COOLEST project you have done to date, EVER !!! WoW !!! And that rhythm it has ...... Thanks for a great video! 👍

    @blk77sunshn@blk77sunshn11 ай бұрын
  • Awesome restoration as usual! Can't wait for the pneumatic quintupel piston oscillating cake frosting applicator, I think Milwaukee made one back in the 50's. My granddad had one, brought it in for a warranty repair back in 64. They said it should be ready by next week.

    @jeffreykipperman6894@jeffreykipperman6894 Жыл бұрын
  • Your vocalizations were priceless when that spring bit you

    @robertvien5693@robertvien5693 Жыл бұрын
  • My month has been made now. Thank you for blessing the people once again

    @DabztoCoffee@DabztoCoffee Жыл бұрын
  • The sound of that "idle" is amazing! I wouldn't think it's supposed to but way cooler.

    @shtboxyj8406@shtboxyj8406 Жыл бұрын
  • I am amazed at how you can take this apart clean, restore, make repairs an then remember where they all go, as an Airforce Vet we had manuals that helped us, an you don't have, amazing job by an amazing guy.

    @cecilgore495@cecilgore495 Жыл бұрын
    • I think he uses the videos to look back and see how everything was assembled, and that's how the channel got started in the first place!

      @Khrrck@Khrrck Жыл бұрын
  • Closed Caption is my favorite KZhead option!!! Thank you as always! -CYC

    @christophercastor6666@christophercastor6666 Жыл бұрын
  • THIS IS *MADNESS.* WHAT KIND OF OVERLY-GLORIOUS MACHINE IS THIS!?

    @scottcates@scottcates Жыл бұрын
  • The tools you restore will never cease to amaze me.

    @andersmoore@andersmoore Жыл бұрын
  • Brilliant restoration for an awesome saw. The guys who earned their living with these tools deserve much respect. Best from the UK where the adjustable HTR spanner is now in use. Thank you.

    @gbentley8176@gbentley8176 Жыл бұрын
  • Any mechanic does repairs, but only someone who has a love for tools does an excellent job like you. This is the best repair channel on all of KZhead. Lots of information, very relaxing and you are so much fun too.

    @cosmefulanito5933@cosmefulanito5933 Жыл бұрын
  • Asbestos gaskets, lead-based paints, radium dials... Working with old equipment shore is fun!

    @IslandHermit@IslandHermit Жыл бұрын
  • As a child I always love taking things apart because I wanted to see how they worked. And I think this is what has led me to restoring tools and different things. To this day I'm still curious how everything works that I take apart. FABULOUS work on this restoration it works and looks wonderful !! 👍👍👍

    @robertmanley7556@robertmanley7556 Жыл бұрын
  • I absolutely love that you use tools you've restored in previous videos.

    @infin1ty850@infin1ty850 Жыл бұрын
    • He makes those old throw-back Screw drivers and wrenches and sells them - they only LOOK old- theyre brand new

      @Mad-Duk_Machine_Werkes@Mad-Duk_Machine_Werkes Жыл бұрын
  • I love it! I've never actually heard a tool go "tah-pock-ah-ta" before. That thing rates right up there with the swing saw as a scary whirling blade flesh-mangler.

    @pfadiva@pfadiva Жыл бұрын
  • Watching a restoration and drinking afternoon tea. Nothing better.

    @digisports22@digisports22 Жыл бұрын
  • I love this kind of shit. Getting to see old tools of the past restored and demonstrated how they were in their prime.

    @Drosera420@Drosera420 Жыл бұрын
  • You are a god damned national treasure. Someone should find a way to get you a platform of some kind where you could just make video content for all of us to marvel at and enjoy on a semi-regular basis.

    @MrCytree@MrCytree Жыл бұрын
  • The craftsmanship and production value of the parts is incredible. I'm a timber fabricator and we byrn through a few plastic crappt drills every year. I can't help but think that's planned out when I see what kind of rigidity and skookum casing these older tools had.

    @Solomon.R@Solomon.R Жыл бұрын
  • Got my perfect handle small screwdriver this week. Just the right size. Carry and use it everyday. Thanks.

    @reggiefaggart196@reggiefaggart196 Жыл бұрын
  • This thing is AMAZING I'm always in awe of the uniqueness of the items you find and restore!

    @VintageStuff@VintageStuff Жыл бұрын
  • This is now one of my favorite restorations you have done. Really nice work. Thanks for the videos! Stay well.

    @DavidWardJr@DavidWardJr Жыл бұрын
    • I'll second that. Nice name, by the way.

      @davidward9935@davidward9935 Жыл бұрын
  • This is a tool you seek out to own not because it is practical or better than your existing tools...but because of the amazing sounds it makes.

    @OmegaGamingNetwork@OmegaGamingNetwork Жыл бұрын
  • i love the old heavy duty air tools. there is essentially an air tool version of every single moving tool you can think of, and they are usually pretty interesting

    @Gunbudder@Gunbudder Жыл бұрын
  • I like that this was named a "safety saw". It's no wonder tools like this don't exist anymore. Where do you find these death traps? They're awesome!

    @funwithmadness@funwithmadness Жыл бұрын
    • Safety saw in that it both had a spring guard that kept the blade away from contact, and also you needed force to retract the guard, a big upgrade over the older ones which had only a cover to keep the chips from hitting you, and no other blade protection, basically a bare spinning wheel of death.

      @SeanBZA@SeanBZA Жыл бұрын
    • These saws were made for underground mines with methane or other explosive gasses. I had a pneumatic chainsaw and a pneumatic arc welder that i used underground

      @anned8634@anned8634 Жыл бұрын
    • @@anned8634 'Pneumatic arc welder' seems like it may be closing the barn door after the horses are out.

      @boothbytcd6011@boothbytcd6011 Жыл бұрын
    • A viewer named Liz Matzelle saw it on Cragslist and sent it in.

      @tektrixter@tektrixter Жыл бұрын
    • @@anned8634 pneumatic arc welder???

      @frogz@frogz Жыл бұрын
  • Holy Kadoodle HTR, cant believe your 90psi @20cfm wasn't enough for this Timber Beast, but then again the size of the 3 pistons was very impressive let alone the trick bearings. Great Job keeping it real with the restoration and repairs! Thanks Much for another @y@ Popping Rescue!

    @pjhalchemy@pjhalchemy Жыл бұрын
    • As a rule of thumb, an air motor needs 8hp driving the compressor for every 1hp delivered by the air motor. They are impressive in many respects, but efficient use of air is not one of them. A Mack truck air starter motor (vane type, very noisy, also made by Ingersoll Rand) uses about 750 cfm. Luckily it spins the engine so powerfully it only has to do it for a couple of seconds. So the air brake tanks, provided they haven't leaked down, will supply enough air. If not, Mack supplied hoses so you could couple up the tyres! Start the diesel engine, fill up the brake tank(s), then refill the tyres and you're off... Turbine starters (eg Austart) are more efficient and quieter than vane type. But they still use a lot of air.

      @Gottenhimfella@Gottenhimfella Жыл бұрын
  • With how many saws and chainsaws you restored that didn't had a shred of safety features this feels like the safest thing you ever handled

    @Chester200100@Chester200100 Жыл бұрын
  • Where you keep finding these rarities baffles me. Another great restoration

    @deezworkshop@deezworkshop Жыл бұрын
  • Every time I see your restorations, it blows my mind how well made they are for when they were invented. My education has unfortunately taught me mainly the bad side of history so seeing these incredible creations gives me a more hopeful outlook.

    @xxPenjoxx@xxPenjoxx Жыл бұрын
  • I love the quotes around "Safety Saw", if they had the winking emoji back then I think they would have added that as well.

    @russellashburn6268@russellashburn6268 Жыл бұрын
    • Yeah, I thought the same thing. You look at the saw and think "that looks totally safe"

      @Ranger_Kevin@Ranger_Kevin Жыл бұрын
    • "Safety" Saw is probably more accurate.

      @jamesholden8256@jamesholden8256 Жыл бұрын
    • Safety is relative.

      @VeraTR909@VeraTR909 Жыл бұрын
  • The noise of the saw motor, and the cutting blade, and the air compressor big enough to run it, makes this most ear-splitting power saw ever.

    @haweater1555@haweater155510 ай бұрын
  • Dude I’d leave that thing chilling on my shelf running, that’s a bad ass conversation starter.

    @agoodballet@agoodballet Жыл бұрын
  • I LOVE THIS THING!!!! WHAT A BEAST!!!! Oh I see now it's from the 1920's ..... I was gonna guess the 1930's but it's even more awesome that this monster was was around even earlier!!! I've watched a couple of color and speed/frame-rate restored films from the 1920's (I can't remember the name of the channel, but they also add some sounds to it just to give you the atmosphere of where they were filmed) and seeing what was around back then it's hard to believe this was the high tech back then, AND that you managed to get it working with very little work (well... I mean very little work as in it was mostly cleaning with only a few small repairs) GREAT JOB!!!!

    @Nobe_Oddy@Nobe_Oddy Жыл бұрын
  • Great resto buddy! I love the old-world look! With the proper compressor, that thing would be scary! LOL

    @captainjerk@captainjerk Жыл бұрын
  • I love doing weld repairs on old aluminum castings like this one! Aluminum wheels area also pretty fun, then again, this old cripple really loves to weld lol. Gotta do something with my free time, when my wrecked back will allow.

    @Adam-th9vs@Adam-th9vs Жыл бұрын
  • Your description of the smell of old, dried grease (Nutella) is so spot on. I can still remember the smell from working on ancient machines back in the day. The memory of the smell is somehow nostalgic... but... in all the wrong ways . Love your videos btw :)

    @tomhill4003@tomhill40035 ай бұрын
  • I may have said this before, but seeing that intro and opening music with the clip, your face... It is better than drugs man, it brings a tear to my eye... I duuno why, is it because you remind me of a friend from a long ago, is it the nostalgic series opening from decades ago when times were better... You are a gift of God to mankind my friend... P.s. a bloody nice saw... I was first thinking it would be a diesel 2 stroke, but when i saw the pneu valve trigger, i was not disappointed, as i didnt read the info... I see your vid, i like and fullscreen, then i read the desc... Either way, yeah, no wonder its got torque for days, that thing with a proper compressor and a 400 liter tank would be able to much through anything... Hell, this thing could only suffer from overheating of the main bearing, as from what i can hear, despite it cooling itself by air constantly, the idle speed increases slowly, which kinda points toward grease being heated up... The pistons and the walls should be getting cooled and contracted equally as one seems to be steel and other cast iron, so no differential shrink rate there, which only leaves the grease churning as the obvious source of heat, which doesnt seem to really be a great thing... I dont know anything about this saw, maybe it likes to warm up the grease and idle at higher speeds, but im not sure at which point of continuous duty does it want a break...

    @camillosteuss@camillosteuss Жыл бұрын
  • I’m always impressed by how you keep everything straight and you know how to reassemble

    @MitchellGuyon@MitchellGuyon Жыл бұрын
    • When you record a disassemble it's easy to reassemble.

      @Vicus_of_Utrecht@Vicus_of_Utrecht Жыл бұрын
  • Nice one! And you don't even hear the screaming saw blade, like on other circular saws... :)

    @petebeatminister@petebeatminister Жыл бұрын
  • -How much air you need to run this? -Yes

    @gplusgplus2286@gplusgplus2286 Жыл бұрын
  • Hope you try it on a compressor with enough air one day. I'd guess it needs a diesel unit like they use with pneumatic jackhammers to run how it should.

    @jaycalgary7@jaycalgary7 Жыл бұрын
    • Looking at the original inlet piping (0:24) it seems to be at least 3/4", so this thing will need quite some air to run at full beans.

      @Ranger_Kevin@Ranger_Kevin Жыл бұрын
  • Saw notification. Deep joy felt instantly. Thanks bud. a ray of sunshine in a damp Irish day.

    @keithfarrell7638@keithfarrell7638 Жыл бұрын
    • Glad you enjoyed it

      @HandToolRescue@HandToolRescue Жыл бұрын
  • You have the sharpest drill bits on KZhead

    @Lobo-ih3bh@Lobo-ih3bh Жыл бұрын
  • What a beast! The saw is pretty good too I guess.

    @morphadge@morphadge Жыл бұрын
  • I find it unbearably funny that the word "Safety" is within the quotation marks of the nameplate lol.

    @Bbeaucha88@Bbeaucha88 Жыл бұрын
    • Safety from that era is like flat earth now; a joke laughed at by most, but still believe in by a shocking amount, unlike flat earth, however, safety is reasonable.

      @the_clockwork_jackass6897@the_clockwork_jackass6897 Жыл бұрын
  • Forbidden, Nutella looks good lol good video I like watching you take old tools and making them look brand new again and they probably work a lot better than they did when they were brand new.

    @BadKarma714@BadKarma714 Жыл бұрын
  • Another master restoration on an extraordinary hand tool. I would never get to see these tools if it wasn't for your channel, Eric. Cheers.

    @channelsixtysix066@channelsixtysix066 Жыл бұрын
  • Awesome. LOVED how it sounded idling.

    @craymosstheater3999@craymosstheater39994 ай бұрын
  • The Angelic sounds and lighting when you smacked the saw blade with a hammer. Awesome.

    @RandyPrimus@RandyPrimus Жыл бұрын
  • That rotating assembly is so dang cool!

    @jerleh261@jerleh261 Жыл бұрын
  • I FELT each of those spring slips

    @jaystevens3548@jaystevens3548 Жыл бұрын
  • Well...Certainly a big saw. SICK restoration as always. GREAT WORK !!!!!!!!!!!!!!!!!!!!!!!!!

    @carlmcgee1623@carlmcgee1623 Жыл бұрын
  • That machine is MENTAL ! Greetings from Southport UK

    @Kevin-gx8lc@Kevin-gx8lc Жыл бұрын
  • I really like the humorous moments that surprise me while I focus on the work technique. You already have two talents. Humor and technical. Big fan.

    @mohdzuhair90@mohdzuhair90 Жыл бұрын
  • Hiya Eric. It was here, then it was gone, now it's back. Glad the video is back.

    @WilliamTMusil@WilliamTMusil Жыл бұрын
  • I felt that spring recoil in my SOUL lol. Also, that first nut you had to properly bust free was a gods-damned miracle (coming from another denizen of the rust belt)

    @williamking9707@williamking9707 Жыл бұрын
  • I tip my hat to you sir, you're one of the few people I've actually seen get an easy out to work!

    @danmooney7192@danmooney7192 Жыл бұрын
  • Love the restoration. That beast needs a plaque that says "I havent had lunch yet. TAG youre it". Thanks for another great video. 👍🏻

    @tinaredington1292@tinaredington1292 Жыл бұрын
  • If I could sum that crazy contraption up in one word it would be “insane”

    @kamoboko86@kamoboko86 Жыл бұрын
  • This is possibly the coolest tool ever, and the scariest. The idle tho.... Damn!

    @sifibuckle@sifibuckle Жыл бұрын
  • Based on your description, I would plan a vacation around the opportunity to wield this blackhole of torque

    @aaronledrew@aaronledrew Жыл бұрын
  • Fantastic resto! I felt your pain trying to reload that spring. OUCH!

    @richardmclean25@richardmclean25 Жыл бұрын
  • Great video.....I am spoiled with modern tools! Thanks!

    @d1gardner@d1gardner Жыл бұрын
  • Who would have thought that a pneumatic three piston/cylinder saw would be a good idea? And than to look at how it was designed, manufactured and run is another amazing feat. And with all that stated, you find such a saw to refurbish is yet another amazing feat as well... Thumbs Up!

    @garymucher4082@garymucher4082 Жыл бұрын
  • the intro to your videos always makes me smile man haha well played

    @mikeyera@mikeyera Жыл бұрын
  • It's very satisfying to see the old tools being beautifully finished.

    @275jesuss@275jesuss Жыл бұрын
  • I felt that spring lol nice job as always

    @lrrromicronpersei8294@lrrromicronpersei8294 Жыл бұрын
  • Love that idle. I'm keen to see it run at full pressure. Cool resto!

    @oohhhhh@oohhhhh Жыл бұрын
  • That's crazy! We still use ingersoll & Rand electric torque drills in our shop! Didn't knew that company existed for that long!

    @rust_hunter7867@rust_hunter7867 Жыл бұрын
  • Like your videos. I’ve been a welder for 35 years, I will have nightmares watching you weld aluminum, lol

    @briangoldman8209@briangoldman8209 Жыл бұрын
  • That is the most wonderfully steampunk wicket saw I have ever seen... damn thing needs to be hooked up to a boiler from an old steam locomotive! What an actual beast!

    @JayFude@JayFude Жыл бұрын
  • Everything was so overbuilt back-in-the-day...and I love it.👊💗😊

    @bones357@bones357 Жыл бұрын
  • I cant tell if I prefer your rougher style of resto, or My Mechanic's perfect restos. I dont wanna choose, so im just gonna watch the both of ya lmao. Much love from Michigan!

    @squibblez2517@squibblez2517 Жыл бұрын
  • I felt your pain mate when that spring came back at you. It made me hurt looking at it.

    @jcramond73@jcramond73 Жыл бұрын
  • A beast of a saw! I love the hardware on it! The bolt heads on this saw are gorgeous! Thanks for sharing 🇨🇦

    @paulcooper2897@paulcooper2897 Жыл бұрын
  • I love the rhythm when it's idling.

    @isaacplaysbass8568@isaacplaysbass8568 Жыл бұрын
  • I have the CC's on and I am hooting and hollering. I love you, man. Good, good stuff.

    @pryordvm@pryordvm Жыл бұрын
  • I must say I really enjoyed watching your work ❤❤❤

    @hassiemlakay4611@hassiemlakay46117 ай бұрын
  • Thank you for the latest installment of Nightmare Tools !

    @paulfox3532@paulfox3532 Жыл бұрын
  • Thank you for helping me appreciate modern tool design!

    @DasAlbatross@DasAlbatross Жыл бұрын
  • Well congrats! You have restored another ancient death machine!

    @de-bodgery@de-bodgery Жыл бұрын
  • I dont watch this channel to see the right tool used for the right job. I watch because its interesting to see how you are going to use what you have to make the rescue work out in the end. 🍻

    @AzraelsTear@AzraelsTear Жыл бұрын
  • Hello, bravo for your restoration, you always have curious objects. Bravo for your humorous videos. Greetings from the south of France

    @olivierquaderi8766@olivierquaderi8766 Жыл бұрын
  • So steampunk and over-dangerous. I definitely love this tool.

    @Akitene@Akitene Жыл бұрын
  • Lo mejor de la reparación. El final con el trenecito...chin ,chin ,pun. Hasta que acelerassss Un saludo desde España.👍

    @nani-df1nf@nani-df1nf Жыл бұрын
  • Great to see Andrei Arlovski is keeping busy these days!

    @jheetman@jheetman Жыл бұрын
  • As always, fantastic video. Very satisfying to watch you complete a restoration, especially with the CC on. Do you ever release any with a voice over? Like your own director's cut, kinda lol. Keep up the great work brother, 1M subs is closing in :)

    @Algorhythmz@Algorhythmz Жыл бұрын
    • Thanks! Yes, narrated videos are on Patreon.

      @HandToolRescue@HandToolRescue Жыл бұрын
    • @@HandToolRescue cool business model

      @calinguga@calinguga Жыл бұрын
  • Love that exhaust note, reminded me of the single cylinder diesel engines from Ruston or Greaves.

    @nsbhagwat@nsbhagwat Жыл бұрын
  • that slow idling is sooo dope :)

    @yzorgone@yzorgone Жыл бұрын
  • You don’t know how excited I am when I see a new HTR video in my subscriptions. Such great work and you always make me laugh. Keep it up brother

    @Whobghilee@Whobghilee Жыл бұрын
  • Every-time I see one of these restorations I can't imagine another one that good or interesting coming along. Great job. Makes me even more glad I came along after these kinds of tools were extinct. A sawyer would go deaf in a week after using this contraption.

    @donparker1823@donparker1823 Жыл бұрын
  • Love the idle of the tool.... Don't change it! Would love to see it work eith a proper flow of airv

    @willcullen3743@willcullen3743 Жыл бұрын
KZhead