This is how we maintained the printers in the last few years .
Пікірлер
Alright now repeat that 20 more times lol
@JB-dv7ew Жыл бұрын
Great video thank you - What material do you have inside your filament dusters?
@renk872 Жыл бұрын
Sponge, I purchased them from amazon.
@mariuschirita2017 Жыл бұрын
@@mariuschirita2017 thanks what kind of sponge? The ones I have tries have degraded over time.
@renk872 Жыл бұрын
@@renk872 Never changed them, I try to turn them around a few times. I just replace the whole filter when they are done.
@mariuschirita2017 Жыл бұрын
👏👏👏...😜👌
@pilotimodele4598 Жыл бұрын
What do you use for lube? Also, isn’t the cold pull better if done with the cleaning filament?
@partsdave8943 Жыл бұрын
I use the lubricant that comes in the box with Prusa printers. Probably any lube would do it . I did read good things about lithium lube but never tried it. The cleaning filament is not very good for cold pulls , it sticks to well on the nozzle and it breaks when you try to pull it out. I found PLA+ does the best job for me. Some people do it with nylon but I never tried it.
@mariuschirita2017 Жыл бұрын
@@mariuschirita2017 My Prusa original MK3 didn’t come with any Lube. Been using 3 in 1 oil
@partsdave8943 Жыл бұрын
@@partsdave8943 I prefer thicker grease, I think it holds for longer. Just my opinion. There are many videos on youtube about grease for 3d printers.
@mariuschirita2017 Жыл бұрын
Hi, in what intervals are you doing the maintenance routine? Monthly?
@additivelabs Жыл бұрын
Ideally monthly, but I don't really have the time to do it monthly, sometimes every 2 months. Cleaning and lubricating the rods is quite important and this can be done more often.
@mariuschirita2017 Жыл бұрын
Have you ever cold pulled with petg?
@bluerider0988 Жыл бұрын
I tried PETG but found PLA+ better. I found PLA+ works very well with the cleaning filament and always had successful cold pulls with it.
@mariuschirita2017 Жыл бұрын
You have 3d printing broking or you dont need it sent it to me bro
@tomhankstomhanks2579 Жыл бұрын
A very helpful and informative video! Marius, we would like to share something with you if you're open to this. What's your preferred email address?
@filamentive2733 Жыл бұрын
Ce fel de spray e ăla,de unde se cumpără?
@remusraita8002 Жыл бұрын
Spray cu aer comprimat / Air duster
@mariuschirita2017 Жыл бұрын
Pretty sure rod lubrication isn't doing anything other than pushing lubricate to the ends of the gantry.
@bernardtarver Жыл бұрын
Yes, it is pushing some lube to the ends, but if you evenly spread the grease along the rod, the balls inside the bearings are definitely collecting a lot. The barrel ends diameter is higher than the rod's. That is the reason I keep spreading the grease a few times while moving the bed and the hotend. This worked very well for me. Some of my printers are almost 3 years old, printing 24/7 and they print like day 1.
@mariuschirita2017 Жыл бұрын
@@mariuschirita2017 certainly that bed sheet looks like new!
@NigelTolley Жыл бұрын
@@NigelTolley that is the newest printer, a few months old. The older printers are on the bottom row. Old down, new up 😉
Alright now repeat that 20 more times lol
Great video thank you - What material do you have inside your filament dusters?
Sponge, I purchased them from amazon.
@@mariuschirita2017 thanks what kind of sponge? The ones I have tries have degraded over time.
@@renk872 Never changed them, I try to turn them around a few times. I just replace the whole filter when they are done.
👏👏👏...😜👌
What do you use for lube? Also, isn’t the cold pull better if done with the cleaning filament?
I use the lubricant that comes in the box with Prusa printers. Probably any lube would do it . I did read good things about lithium lube but never tried it. The cleaning filament is not very good for cold pulls , it sticks to well on the nozzle and it breaks when you try to pull it out. I found PLA+ does the best job for me. Some people do it with nylon but I never tried it.
@@mariuschirita2017 My Prusa original MK3 didn’t come with any Lube. Been using 3 in 1 oil
@@partsdave8943 I prefer thicker grease, I think it holds for longer. Just my opinion. There are many videos on youtube about grease for 3d printers.
Hi, in what intervals are you doing the maintenance routine? Monthly?
Ideally monthly, but I don't really have the time to do it monthly, sometimes every 2 months. Cleaning and lubricating the rods is quite important and this can be done more often.
Have you ever cold pulled with petg?
I tried PETG but found PLA+ better. I found PLA+ works very well with the cleaning filament and always had successful cold pulls with it.
You have 3d printing broking or you dont need it sent it to me bro
A very helpful and informative video! Marius, we would like to share something with you if you're open to this. What's your preferred email address?
Ce fel de spray e ăla,de unde se cumpără?
Spray cu aer comprimat / Air duster
Pretty sure rod lubrication isn't doing anything other than pushing lubricate to the ends of the gantry.
Yes, it is pushing some lube to the ends, but if you evenly spread the grease along the rod, the balls inside the bearings are definitely collecting a lot. The barrel ends diameter is higher than the rod's. That is the reason I keep spreading the grease a few times while moving the bed and the hotend. This worked very well for me. Some of my printers are almost 3 years old, printing 24/7 and they print like day 1.
@@mariuschirita2017 certainly that bed sheet looks like new!
@@NigelTolley that is the newest printer, a few months old. The older printers are on the bottom row. Old down, new up 😉