KZhead
Автокөліктер мен көлік құралдары

excavator FAIL!!!! climbing on truck without ramps

BarZDa Stato
2020 ж. 25 Нау.
437 336 Рет қаралды
Жүктеу

this time it gone wrong :(

Пікірлер

  • Blade goes first, set it on the bed of the truck. Spin around and push the machine up from the rear. Then you can crawl up without moving the truck.

    @mikeznel6048@mikeznel6048 Жыл бұрын

    • Well somebody that knows what they're talking about,who would of thought. Blade up and drive it on

      @roxkrasy8791@roxkrasy8791 Жыл бұрын

    • Thanks for tips, but after this i dont try it again. thanks for watching.

      @barzdastato@barzdastato Жыл бұрын

    • @@roxkrasy8791 There is many ways to do it but blade first is the best way for sure.

      @mikeznel6048@mikeznel6048 Жыл бұрын

    • Yeah this fella was doomed from the very beginning 😂😂

      @dannyc1657@dannyc1657 Жыл бұрын

    • Even doing the blade first, when you boom down to lift the machine up, you also need to stick out so that you are pushing the excavator into the truck. If you only move the main boom the arc of the boom will start pulling the machine closer to the bucket(away from the truck) the lower the boom gets.

      @IndependenceIron@IndependenceIron Жыл бұрын

  • The guy who never made a mistake never made anything. It takes a brave man to show his mistakes for the benefit of others. Well done for sharing.

    @jix177@jix177 Жыл бұрын

    • Thanks for suporting and for watching.

      @barzdastato@barzdastato Жыл бұрын

    • That dosent mean u should make clearly stupid mistakes

      @kalle8836@kalle8836 Жыл бұрын

    • I don't think anyone said it does. But whatever.

      @jix177@jix177 Жыл бұрын

  • Hey I'm a 20 yr operator, and I think you exercise one of the best qualities of operating. You were going slow and being cautious. You just messed up. Experience always wins. And I'm sure you know what you did wrong by now. Good luck man...God bless in Jesus name...

    @tractorman6026@tractorman6026 Жыл бұрын

    • Well said. Thanks for watching.

      @barzdastato@barzdastato Жыл бұрын

    • The worst climbing i ve ever seen

      @nemanjastojkovic7638@nemanjastojkovic7638Ай бұрын

    • Yeah, he tracked the wrong way.

      @jeremyimes6734@jeremyimes6734Ай бұрын

  • Machine cost about £15,000 . Ramps £150 .

    @emclearance5694@emclearance56942 жыл бұрын

    • You are right with your point. But honestly these days alloy ramps for this wight cost about 400...500€.

      @marioreichl7647@marioreichl76472 жыл бұрын

    • I just sold £150. my very good pair of Ifor Williams Steel galvanized ramps each one was 3500kg so a safety weight of 7000kg . But New is £300 to £350 .

      @emclearance5694@emclearance56942 жыл бұрын

    • Definitely it getting a set of ramps that will bring that excavator to the back of that truck for 150. Maybe 1500, used.

      @mikeznel6048@mikeznel6048 Жыл бұрын

    • I often think about this seeing people doing this. It's like, what's the big deal with using some nice high quality aluminum ramps. All the time you spent lining it up and getting in and out the ramps would pay for themselves relatively quickly.

      @eric91780@eric91780 Жыл бұрын

    • come on over I will set you up with ramps and see how you fair in slippery conditions. the last thing you want to be is slipping sideways off ramps

      @xxxmikeyjock@xxxmikeyjock Жыл бұрын

  • I'm with the guy that commended you for showing your mishap. We use trailers in the USA for that, the no ramp method is dangerous for obvious reasons. Take care and be safe.

    @bradh74@bradh74 Жыл бұрын

    • Thanks for watching

      @barzdastato@barzdastato Жыл бұрын

    • ramps are deadly. no way do I use a ramp for loading a machine in a trailer with bedsides

      @xxxmikeyjock@xxxmikeyjock Жыл бұрын

    • @@xxxmikeyjock ramps are deadly?? what?? you load a skid steer without ramps too???

      @taki0ps230@taki0ps230 Жыл бұрын

    • @@taki0ps230 I have a t740 and no where near enough skill to load it without ramps. I might try with a full bucket for ballast

      @xxxmikeyjock@xxxmikeyjock Жыл бұрын

    • @@taki0ps230 the breakover when its slimy is scary A F

      @xxxmikeyjock@xxxmikeyjock Жыл бұрын

  • Hey mate hope your head isn't too sore...you need to learn to use the track levers with your feet and always get the edge of the tray past the sprockets before you swing around also keep the door shut when doing this sort of thing because it adds support to the rops if you do crash and burn, happy digging

    @craigresterman9375@craigresterman93752 жыл бұрын

    • Thanks for advice and for watching. I will never attempt this method again :D

      @barzdastato@barzdastato2 жыл бұрын

    • Nope get the proper equipment like the professionals get a trailer.

      @treesquatch9150@treesquatch9150 Жыл бұрын

  • I guess its so easy to criticise some one who struggles with this manoeuvre. For some this is so easy & done multiple times a day. For others, pure stress. How ever you tried. Much more than many others. That's a +. Im sure by now you have mastered this gig. Well done. Forgive previous harsh comments.

    @thylacine1962@thylacine19622 жыл бұрын

    • How i use to say: nobody born knowing everything. If you want to learn you have to try and from fails that you make on the way, you learn new things and abilties. Now worries all good. Thanks for watching.

      @barzdastato@barzdastato2 жыл бұрын

    • @@barzdastato good luck with all future projects. Truth is you bravely have a go. That deserves respect. I hope your still operating. Rock on Bro.

      @thylacine1962@thylacine19622 жыл бұрын

  • Dude now would be the time to change those hard to reach swing hoses..😅. Glad no one was hurt. I've seen this done a lot but can be dangerous especially if your lags are full of mud. I have a float for my excavator. Very easy and painless.

    @williamturkewitschturkewit1549@williamturkewitschturkewit15492 жыл бұрын

    • Yes, need to stay positive (about hoses :D). Thanks for watching.

      @barzdastato@barzdastato2 жыл бұрын

    • Yes please

      @flightnavigator8999@flightnavigator89992 жыл бұрын

  • So that's why you have a crane fitted to the truck so when you tip your machine over you can pick it up👍

    @danblackman2191@danblackman21912 жыл бұрын

    • Exactly :D. Thanks for whatching.

      @barzdastato@barzdastato2 жыл бұрын

    • Bet you have ramps now, bet that was very scary and lucky you were not badly injured... Be safe fella👍

      @danblackman2191@danblackman21912 жыл бұрын

  • Welcome with the jumpers !!👍🥴😉

    @chenesplit9158@chenesplit91582 жыл бұрын

  • Never climb up like that. Always have the blade as security behind you. I have done this with several types of machines over the years,and in Scandinavia this was s normal way to transport machines. This is a learning video of how you DOBT do it. Glad you are ok.

    @Drummer81able@Drummer81able Жыл бұрын

    • Yes, hope others learn from this.. Thanks for watching.

      @barzdastato@barzdastato Жыл бұрын

    • @@barzdastato mainly...it's most important you are ok. All do mistakes,and i know many who have fallen off,tipped backwards etc etc.. especially in winthertime when it's anow and ice..i never liked it then.

      @Drummer81able@Drummer81able Жыл бұрын

  • Trailers, wonderful inventions they are.

    @danfarris135@danfarris135 Жыл бұрын

    • Yes indeed 😁. Thanks for whatching.

      @barzdastato@barzdastato Жыл бұрын

  • seems like a good way to clean the mud out of the tracks

    @motionclone231@motionclone2312 жыл бұрын

    • True :D Thanks for whaching.

      @barzdastato@barzdastato2 жыл бұрын

  • Così non l'avevo ancora visto, bravo

    @alessandropaolini802@alessandropaolini8022 жыл бұрын

  • Lol. Rookie! That's how NOT to load an excavator! Lol

    @mewhoelse3554@mewhoelse3554 Жыл бұрын

    • Exactly, thanks for watching.

      @barzdastato@barzdastato Жыл бұрын

  • That’s 7.42 I’ll never get back, muppet, stick to loading ramps 🤠

    @heath8779@heath8779 Жыл бұрын

  • What a muppet! The undercarriage is wrong way around… !😂😂 karma , when they want to show off 😂😂

    @paolozusi3680@paolozusi3680 Жыл бұрын

    • Thanks for watching.

      @barzdastato@barzdastato Жыл бұрын

  • Its hard to truly learn what not to do until you have done it, That's what experience is called and with that the ability to change your tactics next time, and bring spare pants lol. I have had my share of machinery scares. Even better when you can correct your own mistakes like you did and big shout out for making it public, I would have burned that video before anyone saw it lol. Well done with the seat belt, Everything else is what it is but without the seatbelt you may be in a very different result. Learn and move on from a nobody down in New Zealand.

    @kiwidiesel@kiwidiesel Жыл бұрын

    • Thanks for watching.

      @barzdastato@barzdastato Жыл бұрын

  • You had to push the machine a little towards the truck and travel in a little before lifting the other end up. Or with a machine this big wi would usually load the blade side first. When you do that you can turn around and track further towards the truck without lifting the other end up from the ground.

    @Kasunderox@Kasunderox Жыл бұрын

    • Thanks for advise and for watching.

      @barzdastato@barzdastato Жыл бұрын

  • There are literally hundreds of videos on KZhead of people doing this successfully. I’ve never seen one of them raise the digger and then try and reverse the truck under it.

    @thegreat_I_am@thegreat_I_am Жыл бұрын

    • This was my thought exactly.

      @capnskiddies@capnskiddies Жыл бұрын

    • kzhead.info/sun/mLN-qNytoniLaqc/bejne.html

      @barzdastato@barzdastato Жыл бұрын

    • Interestingly, I see a lot of videos where the truck/trailer is always driven "under" the excavator when it is high. I would never do it that way. Either you can push up on the truck and reach the loading area with the blade and the undercarriage, which would have been possible without any problems in this case, or you leave it altogether and use loading ramps. Driving the vehicle back and forth is somehow wrong in all areas.

      @vonNachtmahr@vonNachtmahr Жыл бұрын

    • @@barzdastato So it can be done that way! Thank you.

      @thegreat_I_am@thegreat_I_am Жыл бұрын

  • Ačiū Dievui, kad gyvas!

    @serge9846@serge98467 ай бұрын

    • Pasisekė... 😅 Ačiū, kad žiūrite.

      @barzdastato@barzdastato7 ай бұрын

  • molto bravo anche come gruista

    @vivianapalestro9331@vivianapalestro93312 жыл бұрын

  • 15:40 didn’t push out on the stick enough when you pushed down with the boom.

    @mikeznel6048@mikeznel6048 Жыл бұрын

  • Glad you had your belt on man.

    @mikeznel6048@mikeznel6048 Жыл бұрын

  • That was awesome!

    @koas8478@koas84782 жыл бұрын

  • One of those things that's on the "can do it, but shouldn't" list

    @mikepage9520@mikepage9520 Жыл бұрын

  • That mighty beard dampered the fall also besides the belt.

    @MrJokkoma@MrJokkoma2 жыл бұрын

    • :D maybe littlebit :D Thanks for whatching.

      @barzdastato@barzdastato2 жыл бұрын

    • @@barzdastato To be honest, it must be a quite tricky maneuver to load an excavator whit such short tracks on a regular truck.

      @MrJokkoma@MrJokkoma2 жыл бұрын

    • @@MrJokkoma yes it is...

      @barzdastato@barzdastato2 жыл бұрын

  • Never done it myself but those I'e seen done it got that iron bar in front and drive up, then sving the digger around and back up. You do not back the truck.

    @anmoweb@anmoweb2 жыл бұрын

    • Now i know that :D not the best may to find out, but its life. Thanks for watching

      @barzdastato@barzdastato2 жыл бұрын

  • Хорошо что сам жив😉

    @Tatra815s1@Tatra815s13 жыл бұрын

    • ну да, не повезло. Спасибо за просмотр.

      @barzdastato@barzdastato3 жыл бұрын

  • Of you get ot on the truck how do you secure it?

    @treesquatch9150@treesquatch9150 Жыл бұрын

    • On that time i didnt secure it. Thanks for watching.

      @barzdastato@barzdastato Жыл бұрын

  • Just think of how much money you would have saved to have just bought a trailer. Just think of how much TIME you would save to load onto a trailer instead of this risky maneuver. I've seen people with too much confidence and bravado try this maneuver before (and yes most succeed most of the time) but I have NEVER seen anyone try to do this SOLO as the truck driver and equipment operator. That was twice the recipe for disaster. You shouldn't be surprised - sooner or later this was coming your way - its just statistics. I'm glad your ok, hope you learned more from this than simply trying again next time. Imagine doing this and having one of many hydraulic lines burst. Imagine doing this and having the truck brakes let go or the tires lose traction in the mud and start sliding. Imagine doing this and having a soft spot in the dirt cause one end of the blade to sink in. There is only about 100 things outside of your control that could go wrong even if your a top operator who does all your precise maneuvers right - then you put the icing on the cake by doing this alone solo getting in and out of the mini-ex over and over in odd positions. Don't mean to chew you out, but just get a dang trailer. Then you could haul your equipment and a load of dirt it dug at the same time.

    @donaldgulledge729@donaldgulledge729 Жыл бұрын

    • Yes you are right at all points. Peaple learn from their own mistakes, unfortunatly these mistakes are expensive. Thanks for watching

      @barzdastato@barzdastato Жыл бұрын

  • Be careful my friend.god bless you.new subscribe.

    @jun2vlog@jun2vlog Жыл бұрын

    • Thanks for watching and subscribe.

      @barzdastato@barzdastato Жыл бұрын

  • No one believes in chocks until they snap a parking pawl and heart skips a beat and going on a ghost ride.

    @fanningconstruction2050@fanningconstruction20502 жыл бұрын

  • Good job!

    @skliros9235@skliros92352 жыл бұрын

  • Dude... you had it!

    @cdsnider9496@cdsnider9496 Жыл бұрын

    • Yes almost 😁. Thanks for watching.

      @barzdastato@barzdastato Жыл бұрын

  • Бедная стрела 😱 нельзя так нахрапом ехать 🤦‍♂️

    @excovatochic@excovatochic Жыл бұрын

  • You learn from your mistakes just glad you wasn't hurt, it's just as easy using the ramps for safety reasons but if you don't put blade onto tray first

    @patho4908@patho490810 ай бұрын

    • Thanks for watching 😉

      @barzdastato@barzdastato10 ай бұрын

  • Je suis désolé mais je n’est jamais vu monter une pelle comme ça artisan TP j’avais le même genre de matériel et vu comme tu fait acheter des rampes tu sera gagnant en sécurité surtout pour toi et tu sauras on ne descend jamais de la pelle et on monte direct dans la benne et on ne touche jamais au camion salut 👋

    @michelsartorio7073@michelsartorio7073 Жыл бұрын

  • Better to spend a couple of bucks on ramps but hey, you win some, you lose some! Nice digger btw

    @vaclavpolasek6379@vaclavpolasek63792 жыл бұрын

    • Learning from stupid mistakes :) Thanks for watching.

      @barzdastato@barzdastato2 жыл бұрын

    • Crazy how the engine was still running😂

      @vaclavpolasek6379@vaclavpolasek63792 жыл бұрын

  • Норм, зодовку почистил...

    @user-wg1hf2ye2m@user-wg1hf2ye2m Жыл бұрын

  • Потом на авито!не битый не крашенный)))

    @stanislavyur@stanislavyur2 ай бұрын

    • привет, а как иначе 🤣🤣🤣 спасибо за просмотр.

      @barzdastato@barzdastato2 ай бұрын

  • Надо было и кран в конце перевернуть.

    @54sneak@54sneak2 жыл бұрын

  • Kauf dir Rampen dan ist der Bagger in 5 Minuten verladen und ohne Unfall.

    @WP18_-_-@WP18_-_- Жыл бұрын

  • I'm in France and every time i see small excavators like this they just put it in a dumpster then collect it with a roll-off truck

    @Emeric62@Emeric62 Жыл бұрын

  • 🥶🤕

    @Tatra815s1@Tatra815s13 жыл бұрын

  • What damage did the excavator take tho, looks few thousand on repairs probably. 🤪Stay safe

    @user-wt6sz6ox6g@user-wt6sz6ox6g2 жыл бұрын

    • Actually fitted under one thousand, but it was dificult to find who can do such work. Thanks for watching.

      @barzdastato@barzdastato2 жыл бұрын

    • @@barzdastato ooh i'm suprised. Knowing prices for parts for agricultural equipment that's actually pretty low. Sorry for english not my first language.

      @user-wt6sz6ox6g@user-wt6sz6ox6g2 жыл бұрын

  • That's alright, just wear the bucket out scraping on the truck bed, we'll get a new one......

    @galewinds7696@galewinds7696 Жыл бұрын

  • It’s better with the blade the other way👍

    @Andre-ng5ic@Andre-ng5ic2 жыл бұрын

    • True. Thanks for watching.

      @barzdastato@barzdastato2 жыл бұрын

  • Newbs on equipment thats what happens... glad you were not hurt.

    @IBRACIN@IBRACIN Жыл бұрын

    • Thanks for watching

      @barzdastato@barzdastato Жыл бұрын

  • Sah so gut aus der Anfang Schade Mensch

    @yyyxxx7222@yyyxxx72222 жыл бұрын

  • Sure am glad I use a Lowboy.

    @williamdonohue7470@williamdonohue7470 Жыл бұрын

  • Track are clean and free of dirt now.

    @heelerhealer7552@heelerhealer7552 Жыл бұрын

  • Jai fatto un bel lavoro

    @giannidifelice943@giannidifelice9432 жыл бұрын

  • Yeah. Him doing it backward.

    @harolddougherty4724@harolddougherty4724 Жыл бұрын

  • 👍👍👍

    @rienaharyoto3133@rienaharyoto31332 жыл бұрын

  • I think he’s done this before because he came prepared with a crane and the funniest part of all, he put this on KZhead.

    @royr3820@royr3820 Жыл бұрын

    • Thanks for watching.

      @barzdastato@barzdastato Жыл бұрын

  • So you travelled the wrong way after all that set up?

    @LoBeau53@LoBeau53 Жыл бұрын

    • Yes closer to the earth :D Thanks for watching

      @barzdastato@barzdastato Жыл бұрын

  • CONTINUA COSI'

    @marcoforneris2218@marcoforneris22182 жыл бұрын

    • Ahahahah

      @thehyperbiker8757@thehyperbiker87572 жыл бұрын

  • Lucky u alive, expensive experience!

    @snoopy81@snoopy81 Жыл бұрын

  • Good thing he turned the motor off soon after the accident.

    @ericmaxwell4161@ericmaxwell416110 ай бұрын

  • I was biting my nails just watching lol

    @DanielAvilan-tirado7600@DanielAvilan-tirado76002 жыл бұрын

    • It was like in slowmotion movie. Thanks for whatching.

      @barzdastato@barzdastato2 жыл бұрын

  • Cheap excavator up for sale Just a few scratches 😅

    @Anthony-os8id@Anthony-os8id2 жыл бұрын

  • Inexperiente é fogo....

    @noedesbarbosasilvajunior9623@noedesbarbosasilvajunior96232 жыл бұрын

  • That's one way to clean the dust off your machine!

    @joe86johnson@joe86johnson Жыл бұрын

    • Thanks for watching.

      @barzdastato@barzdastato Жыл бұрын

  • Poteva andare peggio, pensa se rompeva la sponda del camion

    @giuseppemarino1694@giuseppemarino16942 жыл бұрын

  • Really sad accident: (

    @paulkivisto9060@paulkivisto906011 ай бұрын

  • You are crazy 😂

    @maxmax3623@maxmax3623 Жыл бұрын

    • Like in movie Mad max lol Thanks for watching

      @barzdastato@barzdastato Жыл бұрын

  • I believe it was WC Fields Who said a sucker is born every 10 seconds

    @redeyedmongoose2963@redeyedmongoose2963 Жыл бұрын

  • And this is the reason i got my self a hooklift truck

    @9Pivo@9Pivo11 ай бұрын

    • Yes, hooklift is a good thing. Thanks for watching.

      @barzdastato@barzdastato11 ай бұрын

  • A Vonde Cojon...👍

    @pienizsrls8045@pienizsrls8045 Жыл бұрын

  • Problem was smal Bukett and soft ground...

    @B16Afreak@B16Afreak2 жыл бұрын

    • Lol. No. Absolutely was operator inexperience. This shit is easy for an experienced operator who knows how to use the boom/dipper and track foot pedals in unison. He needs to practice crawling up over logs and learn how to use boom/ dipper controls with your hands and track controls with your feet in unison and this becomes easy and safe even with a slippery truck deck.

      @sandys9791@sandys97912 жыл бұрын

  • Bro needs a trailer

    @brianvassar2556@brianvassar2556 Жыл бұрын

  • Annnnnnnnd thats what you get!!!

    @aussieearthmoving392@aussieearthmoving3922 жыл бұрын

  • Blade first and youv got this , can be safer than ramps

    @oudonbail@oudonbail Жыл бұрын

    • thanks for watcing

      @barzdastato@barzdastato Жыл бұрын

  • I'm a retired heavy equipment operator and loading in dump truck is easy. Folks please don't do what this guy did.You never get out and you darn sure don't back your truck up to it.

    @spiritwings4592@spiritwings45922 жыл бұрын

    • But it is many videos where they trucking back. Thanks for watching.

      @barzdastato@barzdastato2 жыл бұрын

    • @@barzdastato I've done it many times with no truck moving. As you found out extremely dangerous that way. I'm certified so I know what I'm doing. Just spend time learning the controls. This can be done safely. If I was there I would show you the correct way to do this. Be safe

      @spiritwings4592@spiritwings45922 жыл бұрын

    • @@spiritwings4592 Thanks :)

      @barzdastato@barzdastato2 жыл бұрын

    • But instead of all this back and forth why not say the smart thing why not use that bank to the left of the truck would've been much easier and safer

      @scottmcnichols4885@scottmcnichols48852 жыл бұрын

    • Lol don't try this at home lol

      @devaughangraham1432@devaughangraham1432 Жыл бұрын

  • 😝

    @jameslindley924@jameslindley9242 жыл бұрын

  • This load have ending better when you have use a machinetrailer, 🤔

    @TheUltimate65@TheUltimate65 Жыл бұрын

    • Yes, its true, now i have platform truck. much better :D Thanks for whatching.

      @barzdastato@barzdastato Жыл бұрын

    • @@barzdastato so long you survive its all good..🤗

      @TheUltimate65@TheUltimate65 Жыл бұрын

  • Just first look at the vid i see the mistake instantly NEVER have the blade on the back blade has too be infront ALLWAYS if u lose the Grip the blade will save u and also u will not make that big marks after u on the ground i know it is scary to swing when it's so high up but thats the best way just take it easy dont rush and make sure ur not too far out hope it went well whit the machine and u take care❤

    @broyttube@broyttube2 жыл бұрын

    • Yes it was rookie mistake...I will never again try this method :D. I get fixed machine and now it still working. Thanks for watching.

      @barzdastato@barzdastato2 жыл бұрын

  • Please make a ramps.

    @fathersons8791@fathersons87912 жыл бұрын

  • Ума нет- считай колека, зачем руля крутил? Надо было сразу ровно к кузову подъезжать и при заезде ,,задним,, ходом на платформу рукоять одновременно с ковшом выворачивать. 2 основные ошибки.

    @user-ix3xs5uh1u@user-ix3xs5uh1u Жыл бұрын

    • Спасибо за просмотр.

      @barzdastato@barzdastato Жыл бұрын

  • Рукожоп, ждал когда он в конце ещё и кран положит )))

    @evak-spas5525@evak-spas55252 жыл бұрын

  • Hahahahhau ma come si fa ad esse così anticappati

    @Ziotom132@Ziotom1322 жыл бұрын

  • Should have shut the truck door. It's the little things.

    @slidingdoor9055@slidingdoor90552 жыл бұрын

  • Please don't come to my house

    @oliverhill84@oliverhill842 жыл бұрын

  • U should invest in brown trousers

    @gerardfarrell3135@gerardfarrell31352 жыл бұрын

    • Thanks for watching

      @barzdastato@barzdastato2 жыл бұрын

  • Um piscar a mercadoria tá feita

    @parceirodoagro2068@parceirodoagro20682 жыл бұрын

  • engine out !!!!

    @TheS3fahrer@TheS3fahrer2 жыл бұрын

  • On buy 1500 dollars ramps, and you save money... you don't dammage your excaavtor and your truck And your life too

    @marsoudu87@marsoudu87 Жыл бұрын

  • Put the shuvle on the front 😉

    @lucas_vd_laak@lucas_vd_laak3 жыл бұрын

  • 😩😩😩

    @rienaharyoto3133@rienaharyoto31332 жыл бұрын

  • I po co to cofac babrać sie ramie dalej koparka na pake spych do gory max obrot i wjazd z podpartą łyzka to spora koparka to wjazd szybki i łatwy

    @phuskarbek6834@phuskarbek68342 жыл бұрын

  • Too much counterweight with the beard

    @flightnavigator8999@flightnavigator89992 жыл бұрын

    • Yes looks like that :D

      @barzdastato@barzdastato2 жыл бұрын

  • Lkw mit flachmulde.😜😜😜👍🇩🇪

    @thomasschafer7268@thomasschafer7268 Жыл бұрын

  • Using ramps is faster and more safe.

    @stormnr2@stormnr2 Жыл бұрын

    • After that i bought ramps, but it was not safer. Its very slippery when tracks are wet or frost outside. Thanks for watching.

      @barzdastato@barzdastato Жыл бұрын

  • Keep ur chin up about most comments on here,harf the people here won't no how to drive a digger,the harf that do only think thay can drive a digger, but will be a small few that can operate an excavator and yes there's a big difference. I like the way u own what people are saying so ur on ur way maybe.blade frist next time a,on ya

    @roxkrasy8791@roxkrasy8791 Жыл бұрын

    • Thanks for suporting words. And thanks for watching.

      @barzdastato@barzdastato Жыл бұрын

  • Fast forward to 5:52

    @c50ge@c50ge Жыл бұрын

  • Motor massa

    @tarciscalixto@tarciscalixto11 ай бұрын

  • This is a operator fail, excavator is inocent.

    @polarViking@polarViking Жыл бұрын

  • Si dice che.."u nghiuritu du culu e più forte du terremuatu" cit. Vecchio saggio

    @barrettm8279@barrettm82792 жыл бұрын

  • That cost.

    @emerson2you@emerson2you Жыл бұрын

    • Actually not to much, how it can look :) Thanks for watching.

      @barzdastato@barzdastato Жыл бұрын
KZhead