KZhead

Building a Sakura D5MR vs D5S - Part 1 - Drift Spot Lincoln

Drift Spot Lincoln
2021 ж. 18 Жел.
18 817 Рет қаралды
Жүктеу

So Sakura have released the D5Mr, but whats it like? How does it compare to the D5s?
I decided to buy one, build it, test it, sell it. I don't need the car, but was intrigued as to the differences!
Part 1 - Building the car and comparing parts
Part 2 - On track, how do they compare
• D5Mr vs D5s Part 2 - D...
Thanks
Drift Spot Lincoln

Пікірлер

  • Thanks, this was very helpful. I've just bought the D5 MR v2. I've built 25 plus cars so far but this is my first drift chassis and I will be upgrading as i build. Especially the drive shafts etc as you have mentioned. This is my first build getting back into rc cars. I will now be watching your other videos. Keep up the good work 👍

    @martinbaker7502@martinbaker75024 ай бұрын

  • 100% agree about the axles. Why they chose to do them like that is beyond me. I have changed mine to the d5s axles and I love the way the MR drives on carpet compared to the d5s.

    @mattbrc@mattbrc2 жыл бұрын

    • That review is to follow. But my d5s is so well setup I love it. So I hope the MR keeps up!

      @DriftSpotLincoln@DriftSpotLincoln2 жыл бұрын

  • great, waiting for pt2 ;)

    @gianpaolomiraglia5418@gianpaolomiraglia54182 жыл бұрын

  • I've built 3 D5s now. Including 2 MRs. Even with the new MR v2 that has threaded axles, they still use those weird hexes and small bearings. I just toss those parts and run yeah racing 44mm rear axles, reved SG front knuckles and reved asl front axles. 5x10x4mm bearings all the way around. The 2 other quirks with the D5 are loose rear diff (needs shims) and the input idler gear slop that can cause the gears to bind (also needs shims). IMO anyone who is looking to build a D5 should buy the axles, knuckles, bearings, and shims from day 0, dont even bother with the stock parts. Here is a parts list Rear Axle : SKD5-007BK Front Axle : RV-RD-005 Front Knuckle : RV-RD-001SG Bearings (5x10x4) : PTK-10039 Diff Shims (10x12.5x0.1) : CEGG36910 Input shaft Shim (5x8x0.1) : SER110423

    @DJ.1001@DJ.1001 Жыл бұрын

    • You can probably also run plastic YD-2 front knuckles and standard axles if you're looking to keep everything budget. I have not tried this personally but it should work.

      @DJ.1001@DJ.1001 Жыл бұрын

  • Yeah, I was shocked about the axles. The hex strips very easily, and worst of all leaves some play on the hub for me. I think I may have to retap the threads to secure the wheel. There’s a chance 3racing will release the d5 mini soon, curious to see how they roll out with that

    @thisguy092@thisguy0922 жыл бұрын

  • We’re can I get brake rotors and calipers for a Sakura d5 mr evo v2?

    @Migz625@Migz6256 ай бұрын

  • Where did you get the files for the bumper Prints?

    @MacksDad@MacksDad2 жыл бұрын

    • I made them. They are on thingiverse. Search for DriftSpot

      @DriftSpotLincoln@DriftSpotLincoln2 жыл бұрын

  • I end up use 5x10x4 bearings and using reve-d axles In the front and yeah racing axles in the back. I didn't like them after a few tire changes

    @strippedgears82@strippedgears822 жыл бұрын

    • 100% agree. One of our members has done that too using d5s rear axles.

      @DriftSpotLincoln@DriftSpotLincoln2 жыл бұрын

    • But what about the front axles? Aren’t they also the new “strange” type?

      @DS-ez4er@DS-ez4er Жыл бұрын

    • @@DS-ez4er the new axles are good if you buy the aluminum one the plastic ones snapped easy

      @strippedgears82@strippedgears82 Жыл бұрын

  • The gears in the back on mine are really tight and won’t turn is there something I’m doing wrong?

    @LiquidCandyMedia@LiquidCandyMedia Жыл бұрын

    • Definitely. I THINK if I remember right. In the rear box the 90 degree gears. There are two types. Perhaps you have the wrong one in the wrong place so it's not meshing correctly?

      @DriftSpotLincoln@DriftSpotLincoln Жыл бұрын

  • What is the part number so I can convert to a nut and hex? Thanks

    @tomasborovian@tomasborovian Жыл бұрын

    • Rear axles: SAK-D535 (Although yeah racing do a D5s upgraded set which I prefer). You might also need the bearings specs are shown here: 3racing.shop/products/sak-d535-swing-shaft-set-for-d5s-44mm?_pos=5&_sid=467660d4d&_ss=r Front stub axles I can't find. Check the Manual for the D5s, basically you want the parts from that. 3racing.shop/pages/d5s-manual-pdf It's no wonder the 2.0MR has changed totally to the IFS, and to the normal axles eh? We said it straight off they were weak, and also that the IFS handles better and got back lash from people on our other video. hehe.

      @DriftSpotLincoln@DriftSpotLincoln Жыл бұрын

    • @@DriftSpotLincoln I have a D5MR v2 and I'm mainly interested in the classic self-lock nut. I don't like the screw for tightening the wheels

      @tomasborovian@tomasborovian Жыл бұрын

    • @@tomasborovian Yes to convert over you need new rear drive shafts, new front stub axles, and possibly bearings. Check the links for part numbers. The nuts themselves are easy to get hold of. :) Hope this helps

      @DriftSpotLincoln@DriftSpotLincoln Жыл бұрын

  • did u say something? still dancing tho

    @BenSuzi1980@BenSuzi1980 Жыл бұрын

    • 🤣🤣🤣

      @DriftSpotLincoln@DriftSpotLincoln Жыл бұрын

  • music is so loud

    @tehMaloWalo@tehMaloWalo Жыл бұрын

    • Agreed, poor editing software, wont happen again I promise!

      @DriftSpotLincoln@DriftSpotLincoln8 ай бұрын

  • Sorry too much background music for me otherwise was helpful

    @eltelturbo@eltelturbo Жыл бұрын

    • Yeh noted. It didn't sound that way in the edit but now it's up its stuck like it. Shame. I've lost the original edit files. But for future I'll take note

      @DriftSpotLincoln@DriftSpotLincoln Жыл бұрын
KZhead