Stronger Than Steel! Mix Iron Powder and Superglue You Will Amazed
2023 ж. 13 Ақп.
1 297 741 Рет қаралды
In this video, we show you how effective a combination of iron powder and super glue is when doing repairs. Using iron powder when filling or repairing any gap is very effective and powerful. In fact, the use of iron powder is even more effective than baking soda. Repairs made with iron powder are even harder than steel. Watch this video to learn these mechanic tips and tricks.
Just repaired a broken metal frame from a pair of eyeglasses with graphite (from an ordinary pencil) and superglue. Takes a bit longer until it is hardened (about 30 minutes), but it's hard like stone now and the glue joint seems as strong as welded! Absolutely fantastic!
try mixing baking soda and graphite together, mix well then add the superglue n u get instant, insanely hard bonds
Rough job,.filing the chrome! Mask it on both sides, fill it, wipe smooth, no filing!
When using a sharp knife, work AWAY from your other hand!
interestingly and incredibly useful tip.. thank you sooo much.
3:37 How wonderful! I learned a lot of great tips from your creative videos
Грёбаное любопытство, зачем я это посмотрел
Испытания давлением при открытом кране, вообще поразили!
При открытом кране давление, кстати минимальное, а вот при ЗАКРЫТОМ - максимальное.
@@user-kw1cb2jw6v неужели кэп?
@@Evgeni-Evgenich не знаю, но смотрите "Закон Бернулли"
@@user-kw1cb2jw6v я про то что я это имел ввиду, в первом комментарии.
In the sequence he close the faucet!
Thank you for the very good practical and vividly examples. In my cellar I will be amore a leak water pump tube (hole corrosion) with your ironpowder-superglue-mixture. ;-) Спасибо за очень хорошие практические и наглядные примеры. В своем подвале я буду оберегать протекающую трубку водяного насоса (коррозия отверстия) с помощью вашей смеси железного порошка и суперклея. ;-)
Ничего необычного. Это используется уже лет 40 (а может быть и больше). Есть холодная сварка, можно смешать эпоксидную смолу с железными опилками. Nothing unusual. This has been used for 40 years (maybe more). There is cold welding, you can mix epoxy with iron filings.
Главное при обработке данного состава - дышите глубже
Pó de grafite também é eficiente.
I think you can just use plain old resin for all of these applications, and maybe a bit of powder into it to make it more resilliant, like they do with carbon fiber and glass fibers
Металлическую стружку с клеем болгарка не берет ,а тут напильником кран доработал. Что то не сходится
Это супертехнологичный напильник из адамантия! Это знать надо ёпта!😄
@@knsk1857 А нож тогда из чего? Из вибраниума?
@@knsk1857 смесь ещё не застыла,поэтому и получается и обрабатывается относительно легко. ёпта
@@Alekseykachanov основа сраный суперклей, держит не металл, а сраный суперклей. Который от нагрева плавится и рушится.
С языка снял)))
Thank you for sharing, the video is very useful
Удивил) я это знал, когда суперклей только появился. А ты понял только в 2023 году. Молодец. Учишься.😂
Las mezclas son impermeables? Y la de polvo de hierro se oxida?
Чудо какое средство болгарка не берет, напильник в легкую
NICE IDEA. .... BRAVO 👏👏👏👍👍👍👍👍
Merci pour cette idée j ai souder ma sortie de pot de tracteur tondeuse de la sorte et plus 1an après cela tien toujours très bien
Hi. It looks reliable. It would be nice to see the time difference. Is it as reliable as in the first hours? And won't it weaken when wet? And it is also interesting to see a comparison with epoxy resin. Flexural and tensile strength in comparison 😮
Last month I have repair my water tap (a hole on it) using epoxy resin for simplicity reason. So far it still good.
Re-watch the video It's made from iron And super glue Dear lady
It has +and -
Yes, agree. It should have some engineering measures instead of a show.
yeah, be a good comparison test, looks like some pretty strong $h!t.
Nice idea, thanks :)
Балгарка не берёт, я всегда знал, что напильник это сила!))) Это вторая серия саги "если проволока не держит, то сварке делать нех.....й!“))
Невероятно, поразительно, не может быть.
*The best filler for a molecular adhesive is graphite powder, durable, reliable, and a great combination of materials.* *Самый оптимальный наполнитель для молекулярного клея - графитный порошок, прочно, надёжно, и большое сочетание материалов.*
Oi boa noite po de grafite e mais forte
O que você me diría do pó de carbono?
@@fabioribasdeoliveira7221 Hi! O pó de grafite é o melhor ingrediente para a cola molecular.
@@tokanosunsay3653 Por favor,mas qual grafite exatamente sería o melhor?Talvez grafite "H"?
@@fabioribasdeoliveira7221 O tipo de grafite não é muito importante. Eu pego num lápis normal, trituro-o numa lixa, depois adiciono um pouco de bicarbonato de sódio ao pó resultante e misturo. Aplico esta mistura no objecto a reparar e pingo alguma cola molecular, mas certifico-me de que não se espalha.
Das ist wirklich eine gute und simple Idee! Ist jedoch nichts neues, aber dafür sehr einfach effizient! Wir hatte früher so was ähnliches gemacht: Eine Scheibe, eine sehr stabilie Folie auf der einen Seite, darüber, gewickelt und mit starken Band umwickelt, dann in den Schraubstock gespannt und zugedreht. Das hatte natürlich einen höhere Wirkungsgrad.
I knew about the baking soda hack, but not about using iron filings with superglue! But why not, manufacturers have been adding metal powder to epoxy glue for years.
Iron powder is too expensive , BS is fine for me 🤣
Good but doesn't it dry instantaneously like backing soda?
А если винт смазать каким-нибудь маслом и засыпать таким порошком, его можно будет выкрутить, а резьба останется.Тогда и метчик не потребуется.
резьба может не пропечататься. надо пробовать.
можно фольгой от шоколадки обернуть
@@vadim_4863 or condom 😂
Я попробовал мелкие алюминиевые стружки с клеем на дефектный места гбц автомобиля(где то длиной 4мм и глубиной1мм на поверхности с прокладкой между блоком.это держится пока 6месяц прощел
😮
Он совсем не термостойкий 100град предел. если только не надолго.
@@Jonbraunful так ему даже вытечь некуда, если раковина глухая. Я с эпоксидкой мешал, заделывал раковины выходящие в окна охлаждения. Про результат не в курсе.
What is the temperature of the mixture before it hardens?
Hello from Costa Rica. Wowwwww this is amazing !!!
Очень крутая идея, тыщу лайков!
I am going to try this on an aluminum starter bracket that broke off of a John Deere D105 riding mower. I plan to place a threaded bolt in the spot that’s broken and then put the crazy glue and concrete on top of it.
素晴らしい!
Grazie!!! Fausto
在本視頻中,我們向您展示鐵粉和強力膠的組合在修復時的效果如何。 在填充或修復任何縫隙時使用鐵粉是非常有效和強大的。 事實上,使用鐵粉甚至比小蘇打更有效。 用鐵粉進行的修復比鋼還要難。 觀看此視頻以了解這些機械提示和技巧。
este si esta genial, ya lo probe
The baking soda works like the catalyst of some kind and also as the filler. Using any glue and adding any filller allows to make the strongest joins . It is like to prepare the concrete.
Yes I think he used too much baking soda
I used baking soda to glue my ebike throtle. That joint takes incredible beating and holds for 3 years already.
@@Sopheris Try to use the tobacco ash.
Amigo, muy impresionante su video, gracias por compartir sus conocimientos, siga adelante!!!... 👍👍
can we use iron sand?
Cool my friend... Cool.
Этот cool дано с солью делают или с содой - и не ржавеют окисляясь как опилки железные.
Где взять железный порошок?
Кусок металла, напильник. ))
what is the tensile strength of this material, what is it called? Iron acrylate cement?
Do you use while it is active
Superrr!!!@😀😀😀👍👍👍👍👍
See a few Superglue n powder vids now. The carbon one was interesting, might have to try this as a low temp metal casting method in silicon mods.
I have, and superglue with anything sticks to silicone unfortunately. Don't ruin your mold. Use resin with carbon, or baking soda. A steel mesh will insure a type of rebar reinforcement. Hope this helps. 🤓
Quisiera ver el experimento 3 con una presión hidráulica controlada
Resiste altas tempretauras arriba de 1000 Gc ? es para una mofle de una moto
I think you just 'invented' JB weld. Or at least the base of what would become JB weld. Im sure the offical JB weld product has a few refinements over mixed glue and metal filings.
Be sure to wear gloves, sealed eye protection and a respirator/mask etc to prevent inhalation. When powders are down to the micron levels, they tend to float in the air like cigarette smoke.
А если порошок из керамики смешать, то наверное и дрель не возьмёт, хоть бронеплиты делай
надо на хрупкость проверить. Возможно не пробьет, но удар будет хороший!!!!
where can i buy or get iron dust ?
Пассатижами вместо молотка... Мастер, что сказать...
Regarding the bolt that was fixed into the hole with powdered iron and super-glue; if the bolt has some oil on the threads or maybe a wrap of Teflon plumber's tape, then when the iron/glue sets, you can screw the bolt in and out, as the iron/glue will have bonded to the piece of steel, and have threads on the inside of the hole!
Me extraña que hasta ahorita veo un video con esta mezcla, hace muchos años que me la enseñó un Maestro cerrajero de gran experiencia e inventiva Hasta hoy solo había visto mezclas con bicarbonato y últimamente con grafito ambas tienen lo suyo, pero esta con polvo de acero incluso es exotérmica, lo que indica una fusión inalcanzable para las otras mezclas...
It surprises me that until now I see a video with this mixture, many years ago a Master locksmith with great experience and inventiveness taught it to me. Until today I had only seen mixtures with bicarbonate and lately with graphite, both have their own thing, but this one with steel powder is even exothermic, which indicates a fusion that is unattainable for the other mixtures.
👍👍👍👍👍
STRONGER THAN STEEL!!! *video literally shows this being cut with steel
Pamuk ve hızlı yapıştırıcıyı dene o çok daha sağlam oluyormuş.
Позвоните доктору Дью?😂
how about titanium powder??
Can it be used to repair electrical water heater tank (iron or copper) with working temperatur up to 75 degree Celcius ?
you can use adhesive name Metallica of Astral
no superglue only has a workign temp up to 60 deg c
Dann muss man einen Kleber nehmen der auch längerfristig Feuchtigkeit verträgt, Temperatur sollte kein Problem sein. Es gibt zu den Produkten meistens auch Datenblätter.
Я отсюда чувствую вонь от этих испытаний😂
Дымок , что надо, коллапс лёгких обеспеч🤣ен..
В ядерной войне 18-го века использовались именно такие технологии.🤭
может вы плохо помылись? или давно не мылись? рекомендую больше времени уделять гигиене. :)
@@user-nn6xo5vm1o так пахнет только жженый цианакрилат🤣
иногда случается в жизни использовать ТАКОЕ... отчего волосы встанут дыбом и... выпадут.
А термическую проверку прошла металлическая пудра ?
What is the best source for the iron powder? Can we buy?
OMG, I will do this definitely now Super Glue Cement Epoxy is getting so expensive and l need it a lot for things I am making.
bro at 0:56 its indestructible and at 2:57 it cutting easy...........hummmm..
I was hopping to see this. You noticed it .
1:51
MUITO BOM
I like this. I will use this technique to repair broken laptop hinges.
How does the iron dust compare to graphite powder?
Думаю она просто крупнее))
Алюминиевую пудру можно использовать?
лучше пудру для лица. в ней есть тальк, окись цинка и двуокись титана. клей активирует молекулярную структуру титана. крепче получится чем просто с металлической пудрой.
Can we buy....the iron dust....from the market....or must keep it from our...tasks.....some other time....???
You can gets the iron dust from warm bag that people warm hands in winrer.
I wanna try it.
What if you added Aluminum filings to that mix ?
Aluminum and iron no bueno
Интересно вместо железного порошка использовать отработанный тонер... По идее тонер - это пыль из оксида железа и смолы.
мы так и делаем. но постарайтест не везде распространять эту информацию. плиз.
Ну да человек изобрёл наполнитель для клея зачёт! Еще изобрети брусок какой то образив возьми и с эпоксидкой смешай. Тут и эпоксидка которую все любят и напильник точить не будет, точнее напильник будет стачиваться и ножи таким точить можно будет!
Вы только что изобрели корундовый полимеробетон аналоговнет😂 " срочно патентовать"
How can you find iron powder, It is not easy.
da un fabbro?
Ma io vorrei sapere quale è la "super glue"!
From where u get Iron dust ???
드릴에도 견디고 망치로 두드려도 멀쩡한데 2:57초 3:53초 부분 커터칼에 쉽게 잘려나가는 수준...아! 커터날이 또 다른 특수한 장비인가 보군요.
Col cutter magari prima che indurisca.
Лезвие ножа сделана из вибраниума.
También lo note, queda en evidencia la poca confiabilidad del vídeo , saludo desde Colombia
War vielleicht noch nicht ausgehärtet, unter Verwendung von Zuschlagstoffen dauert es länger bis zur Endfestigkeit.
Y el polvo de hierro tan fino ¿cómo lo consigues?
Wonder if it works with iron oxides? I don't have iron powder but iron oxides.
You a Prospector?
Шлифмашинка абразивом не берет, а простой напильник отлично пилит :)))
засунь свой русский... учи английский
@@milordas , мне насрать на твой английский
@@milordas засунь свой русский... учи английский
cool, but where can you actually buy baking soda?
Plant a soda tree, harvest the leaves, dry them, crush them, wash/rinse with bleach, you can thank me later. lol
Выкручиваться болт плоскогубцами даже не пытаясь их сжать.
Наконец-то я вижу умное видео. Просто поразительно помешательство общества на соде. Сода - самый неподходящий наполнитель по двум причинам: она непрочная, хрупкая, легко колется и размалывается и она растворяется в воде. Атмосферная вода (пар) будет медленно, но неумолимо разрушать склейку с содой. А вот железный порошок - вы сами видели только что, насколько он прочен. Такая склейка будет оставаться прочной много лет. I'm finally seeing a smart video. The society's obsession with soda is simply amazing. Soda is the most unsuitable filler for two reasons: it is fragile, brittle, easily pricked and crushed, and it dissolves in water. Atmospheric water (steam) will slowly but inexorably destroy the bonding with soda. But the iron powder - you've just seen for yourself how durable it is. This bonding will remain strong for many years.
You filed it! But it was difficult to grind it?
Dervirá para una grieta en el piso de un box de ducha de acrilico.?
Analogamente, sì. Vuoi che ti diciamo pure se funziona sulla moquette?
The reason why this mixtures give good bonding results .Is because the pulverized particles resent lots of bonding area an create strong links
well done
또 하나의 꿀팁을 얻었다
耐熱温度は何度ですか?
Hitzebeständig?
Nice. Where can regular "urbanic" man can get this Iron Powder? 🤔
The problem is, where do you get iron powder?
I'm asking the same question
@@leonardjones7707 Passe uma chave velha no esmeril e coloque um papel branco por baixo da pedra do esmeril e verá o pó cair.
🙏
Toller Wasserdruck da Pinkele ich Kräftiger
el problema de todos los pegamentos es la temperatura ,por encima de 80 grados estas mezclas suelen perder propiedades
I've been using my pliers all wrong.
The more you know right
try with aluminum, bronze powder
From where do you get Iron Power?
There's probably some in your hot hands hand warmers! But be careful. It reacts to oxygen. That's how it gets it's heat
👏👏👏👏👏👏
ide like to see iron glue vs jb weld.
¿donde se consigue el polvo de hierro?